Search Documents

By L. S. Reid, Irwin Politziner F. M. Townsend

Recently published data indicate that the water vapor content of a gas, as determined by dew point measurement, is inaccurate when the gas has been dehydrated with diethylene glycol. Water vapor contents and dew point measurements of gases dehydrated with triethylene glycol have been obtained in this investigation in order to determine the magnitude of a similar error, if one exists. Experimental data show a very low concentration of triethylene glycol vapor in gases dehydrated at atmospheric ternperatures and pressures ranging from 500 to 2,500 psia and that the accuracy of dew point measurements is not impaired by the presence of triethylene glycol vapor. INTRODUCTION Nearly all natural gas transported by pipe line to northern and eastern markets must be dehydrated to a low residual moisture content in order to assure maximum transmission efficiency and continuous delivery under peak load conditions. Without dehydration, water vapor often condenses in pipe lines in quantities sufficient to restrict the flow3 and. under low atmospheric temperature conditions, gas hydrates may form and plug gathering. transmission and distribution facilities. Gas may be dehydrated to pipe line specifications by a number of methods. The most widely used methods are (1) adsorption of water vapor on a solid dessicant such as activated bauxite, alumina or silica gel,' (2) by absorption of water vapor by either diethylene or triethylene glycol-water solutions of high glycol concentration,11,13 and (3) by simultaneous expansion-refrigeration of very high pressure gas in which gas hydrates are purposely formed and then quickly decomposed.'"" Of these three fundamental methods, the adsorption and absorption processes provide the bulk of the dehydrated gas moving to market at the present time. The expansion-refrigeration process. a relatively new development, is gaining in favor because of its simplicity but is sharply limited in its application by available differentials between source and gathering system pressures. Where gas sale or purchase contracts contain a maximum water vapor content specification, the water vapor content is usually determined by measuring the dew point of the gas at system pressure. Knowing he dew point temperature and the system pressure, the water vapor content of the gas is determined from a graphical correlation of saturation, or dew point, temperature us the water vapor content of the gas which is customarily expressed as pounds of water vapor per million cubic feet of gas measured at 14.7 psia and 60°F. Dew points are usually measured with the U. S. Bureau of Mines Dew Point Tester. shown in Fig. 1, which is well suited for use at temperatures lower than 120°F and at pressurei; ranging from atmospheric to 3,000 psi. A number of correlations of dew point temperatures vs water vapor content are available,3,5,15 the most recent of which is that by McCarthy et al.4 Where natural gas is dehydrated by absorhing contact with concentrated diethylene glycol-water solutions. considerable difficulty is experienced in observing water dew points due to condensation of liquid hydrocarbon and glycol films on the mirrored surface of the dew point tester. Riesenfeld and Frazierl2 report that the dew point method for determining the water vapor content of a dietllylene glycol-treated natural gas is in error due to the glycol content of the condensate formed on the tester mirror, and that the water vapor content of the gas tested is actually lower than that indicated by the standard' dew point-water vapor content correlation. Extensive experience in testing gases dehydrated by concentrated triethylene glycol-water solutions lias not revesled difficulties of the nature cited above for diethylene glycol. Water dew points are clear and sharp and condensation of

Jan 1, 1951

By R. J. Caro

The Anaconda phosphate plant was put into operation in the fall of 1923. Its present daily operating capacity is approximately 170 tons of treble superphosphate and 16 tons of phosphoric acid analyzing 42 pct P2 O5 and 52 pct P2 Os, respectively. As a result of the continued increased demand for phosphates, Anaconda decided in 1947 to expand the plant's daily output to 270 tons of treble superphosphate and 54 tons of phosphoric acid. The present daily plant intake is 335 tons of wet (footwall) phosphate rock analyzing 31.7 pct P² O5 and 0.28 pct V² O5. The rock is shipped from Anaconda's mine at Conda, Idaho, in open railroad cars, having been crushed to pass 3/8 in. mesh at the mine.' The expansion program will require an increased intake of 300 tons of rock per day. The hanging-wall rock anaIj-ses approximately 30.5 pct P2 O5 and 0.11 pct V² O5, and will be beneficiated in a new washing plant under construction

Jan 1, 1950

By S. G., Lasky

IT seems to be in the nature of concepts that they have many meanings, and that the meaning best reflecting the primary interests of a person tends to be accepted by him as the normal meaning of the concept. The concept of ore reserves is no exception, for there is no unanimity of meaning among the several groups of us who are interested in ore reserves, nor even among the individuals of a single group. The groups most interested in ore reserves would seem to include at least the mining industry, perhaps State taxing agencies, and the Federal Government in all its diversified activities, and I would include also the citizenry at large or at least that part of it that consciously thinks about problems-of national welfare. To each of these, and to different individuals within them, the term reserves represents something different, and the farther away the individual or group gets from physical contact with the ore, the more abstract does his or its concept become. It is something different to the policy maker from what it is to the fact-finder or to the miner.

Jan 1, 1945

By G. E. Karantzavelos

Anew flotation process to recover alunite from low-grade alunite ores is described. The process begins with run-of-mine ore, reduced to less than 5 mm (0.2 in.), being preconditioned with the reagents before grinding and alunite flotation. From the preconditioning step, ore particles, impregnated with reagents, form pellets that subsequently disintegrate into the pulp during grinding. The second step is basically a standard alunite flotation step. Pilot plant test results show that an alunite concentrate assaying at least 85% alunite and less than 5% silica can be produced. Laboratory and pilot plant results were in excellent agreement, indicating that the new process is a viable means of alunite beneficiation. Plant results, using the new process, were superior to results from conventional alunite flotation procedure.

Jan 1, 1986

By AIME AIME

WITH a brilliance undimmed by hard times, the annual dinner on Wednesday evening, Feb. 17, was a complete success. More than 600 members, friends and ladies gathered early and filled the anterooms of the grand ballroom of the Commodore Hotel, while the president's reception was in progress, and then at the sound of the gong and with the music of the orchestra, rising above the happy din of conversation thronged to their seats at the tables. Following the "potage Ambassadeur"-probably to eliminate a very real hazard-the usual toy balloons appeared and a gay and lively scene, punctuated by multitudinous explosions, ensued, as the hundreds, of variously colored spheres bounced yon and hither until their gaseous existence was ended on the glowing end of a cigar or cigarette. On the speakers' dais sat C. E. Beecher, Chairman Petroleum Division; J. Vipond Davies, representative of A. I. M. E. on the Alfred Noble Prize Committee; Corbin T. Eddy, Alfred Noble Prize recipient; A.' S. Tuttle, Vice-president American Society of Civil Engineers; W. C. Mendenhall, Director U. S. Geological Survey; George C. Bateman, representing the Canadian Institute of Mining and Metallurgy; Paul D. Merica, Institute of Metals lecturer and Chairman James Douglas Medal Committee; Champion Herbert Mathewson, James Douglas Medalist; Robert E. Tally; retiring President; G. Temple Bridgman, toast-master; Scott Turner, incoming President; F. W. Bradley, William Lawrence Saunders Medalist; Fred Searls, Jr., Chairman William Lawrence Saunders Gold Medal Committee; Arthur Notman, President Mining and Metallurgical Society of. America; Robert J. Grant, Director U. S. Mint; Landon F. Strobel, Chairman New York Section; Howard Scott, recipient of Robert W. Hunt Prize; George. B. Waterhouse, Chairman Robert W. Hunt Prize Committee; F. M. Becket, Chairman Iron and Steel Division; Ora E. Clark, recipient of the J. E. Johnson, Jr., Award; Richard Peters, Jr., Chairman J. E. Johnson, Jr., Award Committee; E. C. Bain, Howe Lecturer; Sam Tour, Chairman Institute of Metals Division; and H. Foster Bain, Chairman. Charles F. 'Band Foundation Committee. ' Each was heartily applauded when introduced by Mr. Bridgman, as was Mrs. Tally, who also made a bow. The toastmaster made graceful reference in introducing Mr. Strobel, to the large part the latter had taken in planning the meeting.

Jan 1, 1932

Succession of Minerals and Temperatures of Formation in Ore Deposits of Magmatic Affiliations BY WALDEMAR LINDGREN (Tech Pub 713 10,000 words ) The paper presents data accepted by many geochemists and geologists regarding the succession of minerals and the temperatures of formation in ore deposits affiliated with igneous rocks It also presents the individual views of the author on the composition of the solutions that were active and on the mode of deposition He does not regard these views as speculations or hypotheses but as forming a well motivated and con¬sistent theory It is not certain, however, that all investigators will subscribe to them The mining engineer may not always be interested in the field of stability and tempera¬ture of origin in the mineralogy of ore deposits, but he certainly is interested in the succession of minerals because this has a definite bearing on the understanding of the ores and on the best processes of extraction The author, therefore, summarizes in plain language the principal features of succession as shown in metallic ores

Jan 1, 1937

A filled stope is one in which the support for walls and men and, at times, for the back of ore, is furnished by waste rock or sand tailings. The filling may be rock sorted out in the stope or from the walls, develop-ent, or the surface. The orebody is mined in sections, each practically an open or timbered stope, filled wholly or in part before adjacent ground is attacked. As a rule, the filled-stope method is limited to overhand flat-back, stepped-face, or rill stopes. The examples given are Copper Range, Iron Cap, Verde district, Zaruma district, Lucky Tiger, and Silver King Coalition.

Jan 1, 1925

By R. F. Mehl, M. Gensamer

THE stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals1 has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.2 It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. ‡ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, whether deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of

Jan 1, 1938

By W. G. Sinclair

THE North Texas district presented in this paper includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger and Young. It corresponds with the Texas Railroad Commission's district No. 9. Table I conforms with the nomenclature of pools as designated by the Commission. Most of the oil and gas produced in this region, generally referred to as the Red River uplift, comes from the Pennsylvanian strata. In recent years, however, increasing amounts are being developed in both the Mississippian and Ordovician.

Jan 1, 1946

By W. G. Sinclair

The wartime momentum of exploration continued throughout the year 1945 despite the end of hostilities in mid-August. The table below illustrates drilling activity in the various categories: Completed wells. . . . . . . . . . . . . . . . . . . . . . . . 401 Wildcats.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104 Wildcat discoveries, oil.. . . . . . . . . . . . . . . . . . . 2 Wildcat discoveries, gas-condensate.. . . . . . . 4 Development wells.. . . . . . . . . . . . . . . . . . . . . .297

Jan 1, 1946

By H. A. Baumann, A. J. Rostosky

EVER since the first installation of wet-washing methods of coal preparation, the removal of the water added by the washing process has created serious technical and operating problems. The rapid development and widespread adoption of wet washing has necessitated a corresponding development of dewatering methods and equipment. The amount of water retained by coal varies with the size of the coal. The moisture that is largely on the surface of the particles is easily shaken off coarse coal; thus coarse coal can be dried comparatively easily and quickly. Fine coal presents a larger surface area than does coarse coal, so its capacity for retaining moisture is greater. In fine coal, moisture below about 5 per cent is held between the coal particles and its removal is difficult. Draining and drying of the finer sizes is a major problem at many washeries. Two common problems of coal-washing practice that are intimately connected with dewatering and drying are the clarification of washery water and the prevention of stream pollution. The first field has been studied from many angles, including the use of coagulating and settling agents followed by vacuum filters to remove the solids, and the use of sludge tanks with dewatering screens incorporated therein. In many districts, the disposal of sludges into streams has been stopped by law. The lack of space for impounding sludges has created problems of disposal in other districts. Reduction in moisture means a saving in freight costs as well as the elimination of difficulties in unloading and storing. Excess moisture in coal causes it to freeze in localities where severe climatic conditions pre¬vail. Excess water in coals to be used in the production of coke and manufactured gas has a chilling effect on the walls of the oven or retort. Dryness of coal is important in producing good briquettes.

Jan 1, 1943

By John Dodd

This paper reviews advances in the technology of abrasion resistant iron and steels, which could help combat abrasion and wear in mining operations. With the recent progress in high chromium alloy iron development, high temperature heat treatment of massive castings can be eliminated, aloy cost reduced, and cracking problems avoided. Data on erosion-corrosion resistance of these irons; trends in the development of improved cast steels; and factors influencing toughness and abrasion resistance of manganese steels are all considered. The 7% Mn. 1% Mo manganese steels are shown to combine toughness and abrasion resistance, and composite castings are a means of combating abrasion in applications involving severe impact. A brief appraisal is given of recently developed martensitic wrought steels with improved weldability.

Jan 1, 1982

By AIME AIME

WILLIS McGERALD PEIRCE-"Jerry" to his host of friends, and on that account a hit of a puzzle to those who have known him only as "W. 14."-a native of Buffalo, educated at Penn State College, Illinois: and Yale universities, has bee11 associated throughout all of his professional career with the New Jersey Zinc Company. Jerry has served successively as investigator, section chief, and division chief in the research department of the company and has just been promoted to chief of research.

Jan 1, 1937

By R. E. Mussler, F. E. Block, T. T. Campbell

An exploratovy study was made to deternzine the feasibility of preparing beryllium by the metallother-. mic reduction of beryllium oxide. The procedure involved heating a relatively nonvolatile metal reductant in contact with beryllium oxide in a vacuum. Beryllium vapors formed in the reaction were condensed as a coherent deposit on a heated surface. Reductants tested included tanthanun, yttrium, thorium, Th-Mg, and Zr- Ti alloys, and the hydrides of lanthaniir~z, yttriunz, and zirconiur?7,. Test ten7pevatures ranged from 1350'to 175O' C, and reaction times ranged frot 30 to 100 lzr. In most cases metal recoveries were lola, although yields close to 90 pct of theoretical were obtained with latzthanum, yttrium, and zirconium reductants. In most cases metal deposits were contanzinated by beryllides, /ls/cally of the Beln M or Bel3 M type. BERYLLIUM has a variety of unique properties including light weight (sp gr 1.85), low thermal neutron absorption cross section, high scattering cross section, excellent dimensional stability, high strength to weight ratio, high melting point (1285"C), high specific heat, and high thermal conductivity. Interest in beryllium as a structural material in aerospace and nuclear-reactor applications is based on these properties. In general, the potential of beryllium has been only partially realized, largely because of the brittleness of poly crystalline forms of beryllium, difficulties associated in its fabrication, and joining problems encountered in its use in structural applications. Several excellent books and monographs are available to those interested in the occurrence, extractive metallurgy, and utilization of beryllium.1"* Although an extensive amount of research on beryllium has been in progress during the past 10 years, much of the work has been concerned either with the so-called "ductility problem" or with the development of methods of fabrication and evaluation of properties of various commercial or purified grades of metal. A recent survey of the literature indicates that only limited efforts are presently being directed toward developing new methods for reducing beryllium compounds to metal. Two major commercial methods now used to produce beryllium are the magnesium reduction of beryllium fluoride and e lec trow inn ing of beryllium from fused sodium chloride-beryllium chloride salt baths. Only a limited amount of work has been done on the direct reduction of beryllium oxide. Major factors which complicate this method are the great stability of beryllium oxide and the reactive nature of beryllium metal. The stability of the oxide necessitates extremely high reduction temperatures and vacuum operation to liberate beryllium metal vapor and cause reactions of the following type to proceed: XBeO(s) +YM(s)-MYOX(s) + XBe(& As early as 1939, roll' used this reaction for the direct reduction of beryllia by zirconium and titanium, and later in 1952 ~a~el~ studied the reduction of beryl-

Jan 1, 1967

By A Andersen

DURING an investigation of the copper-rich portion of the copper-silicon-iron system as part of an extensive research program on P.M.G. alloys, which was begun in 1937 in the research laboratory of the Phelps Dodge Corporation, it became apparent that the binary copper-silicon system below 7 per cent Si needed revision, therefore an investiga-tion was undertaken. Both X-ray methods and microscopic technique were employed. Despite the many investigations that have the clarification of this sys-tem as their object, no two successive reports on the system have agreed in placement of the alpha-phase solubility limit, and uncertainty about the secondary phase first to appear has been voiced several times.3,4,5 It was therefore not surprising, when T. Isawa's6 and M. Okamoto's7 works were reported at the time we were finishing up our experimental work, to find essential disagreement between their results and ours. But when C. S. Smith's latest work on the copper-silicon system8 was published just as we were finishing our laboratory report, it was indeed gratifying to find that the latter's diagram and ours checked in all essen-tial features, except the temperature of the peritectic line above 830° C. Many attempts were made to retain the beta phase during the present investigation, but none was successful. Isawa,6 however, reports that he has been able to obtain X-ray photograms of the beta phase. The structure, he states, is body-centered cubic with a lattice constant of 2.848 A.. at 7.2 per cent Si. Okamoto7 and Smith8 both use the designation Kappa for the hexag-onal phase, and to avoid confusion this designation will be adhered to in the present paper.

Jan 1, 1939

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by plotting [So = ooT as a function of eo =o] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors? It was shown that the true physical behavior of the material in the tension test could best be represented by plotting the average true stress, [S = P] as a function of [e = q' = log A-le = log Lo] where P, A, L, S, [e], and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

ONE of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing of the A.S.T.M., 1938. The work of Mann,1 Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserve especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by [P OL, plotting So = Ao as a function of eo = Lo] where A o and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors' It was shown that the true physical behavior of the material in the tension test could best be represented [by plotting the average true stress, S = P as a function of e = q' = log o = log Log] where P, A, L, S, e, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximum load point to fracture. The construction of such- curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain difficulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece

Jan 1, 1941

"The mountains of Utah contain one of the largest deposits of high grade bituminous coal in the world. According to the United States Geological Survey, there are 13,130 square miles of land known to contain workable coal, and these extensive fields contain 196,000,000,000 tons of coal. More remarkable than the extent of the coal fields is the thickness of the coal beds. Over three-fourths of the output of coal in Utah is recovered from beds ranging from 8 to 17 feet in thickness, as compared to one-eighth of the output of the entire country from such beds. In 1917, Utah mined one-third of its coal from seams at least 16 feet thick, compared to one-half of one per cent of the total bituminous output of the country from like seams.Coal at Wales, in Sanpete County, and in the vicinity of Coalville, Utah, was, it is reported, the first discovered by white men in the state. Wales claims the distinction of having produced the first coal mined in Utah. Two men, who had been coal miners in Wales, learned of the coal from an old Indian chief who called it ""rock that would burn."" In 1857, the town of Wales was founded and coal mined, and in 1858 some coke was manufactured and hauled by ox team to Salt Lake City. South of Wales is Castle Valley, in Wasatch Plateau field. From 50 to 60 miles of the Old Spanish Trail from Santa Fe, New Mexico, to Monterey, California, lies in Castle Valley. The coal in this field may or may not have been known at the time the trail was used extensively. The first published reference to this coal, however, was made by a party of the Corps of Topographic Engineers in their journal for October 11, 1853.After the completion of the Union Pacific railroad in 1869, mining on a commercial scale was attempted. In 1876 the Utah and Pleasant Valley railroad commenced operations between Scofield, in Carbon county, and Springville, Utah county, and following the year 1878, when the Rio Grande Western railway began construction through the Carbon county field, development increased until in 1900, when large smelters commenced operations in Salt Lake valley and gave coal mining in Utah an impetus that first carried it to an annual output of a million tons. During the past fifteen years many new mines have been opened, and with the construction of the Utah railway, an exclusive coal road, from the properties of the United States Fuel company in Carbon and Emery counties to connect with the Union Pacific system at Provo, the state reached a maximum production of 6,005, l 99 tons in 1920."

Jan 1, 1925

By Terkel Rosenqvist

Few subjects in iron metallurgy and steelmaking have caused so much discussion and have resulted in so many divergent and partly contradictory statements as the theory of the distribution of sulphur between molten iron and slag. An interesting survey of the different points of view is given by Grant and Chipman.1 Grant and Chipman themselves conclude in their paper that, at least in the open hearth and electric steel furnaces, the governing reaction is a simple distribution like: FeS steel ? FeS alas [Ia] and MnS steel ? MnS alas [Ib] They conclude that no significant reaction takes place according to the more classical scheme: FeS steel + CaO slag ? FeOslag + CaS slag [2a] This is the reaction which is regarded by most investigators as the primary sulphur reaction in the blast furnaces, where it is accompanied by the reaction with carbon: FeO slag + C ? Fe + CO [2b] The writer suggests an alternative to the reactions mentioned above. It is the opinion of the writer that the a priori assumption of defined molecular compounds being present in molten steel as well as in molten slag, has retarded rather than promoted a solution of the sulphur problem. As for the constituents of molten steel, it is taking too much for granted to mention the presence of FeS and MnS. If this infers that the melt contains diatomic molecules, the statement must be made that at least such molecules do not exist in the solid state at room temperature. Solid FeS crystallizes in the nickel-arsenide structure, and MnS (high temperature form) in the sodium-chloride structure. In these structures the sulphur is surrounded by six metal neighbors, and no molecular groups can be isolated. When sulphur is dissolved in molten steel, it is expected to maintain the same coordination number as in the solid state. We know that sulphur in steel has a certain chemical potential and a chemical activity which can be expressed by the reaction: S steel + H2 ? H2S where the activity A. is proportional to the ratio PH2S/Ph2. We know also that this activity is influenced by the presence of other constituents. For instance, there is reason to assume that carbon and silicon increase the sulphur activity and manganese decreases it. However, the exact relationship here is scarcely known, and further investigations are needed. Concerning the molten slags, if anything should be assumed a priori it would be that they are composed of ionic rather than molecular parts. There are indications of this in that solid silicates form ionic structures, and molten slags show high electric conductivity and can be electrolyzed.2 It has been claimed by Taylor and Chipman3 that their activity investigations

Jan 1, 1949

By Terkel Rosenqvist

Few subjects in iron metallurgy and steelmaking have caused so much discussion and have resulted in so many divergent and partly contradictory statements as the theory of the distribution of sulphur between molten iron and slag. An interesting survey of the different points of view is given by Grant and Chipman.1 Grant and Chipman themselves conclude in their paper that, at least in the open hearth and electric steel furnaces, the governing reaction is a simple distribution like: FeS steel ? FeS alas [Ia] and MnS steel ? MnS alas [Ib] They conclude that no significant reaction takes place according to the more classical scheme: FeS steel + CaO slag ? FeOslag + CaS slag [2a] This is the reaction which is regarded by most investigators as the primary sulphur reaction in the blast furnaces, where it is accompanied by the reaction with carbon: FeO slag + C ? Fe + CO [2b] The writer suggests an alternative to the reactions mentioned above. It is the opinion of the writer that the a priori assumption of defined molecular compounds being present in molten steel as well as in molten slag, has retarded rather than promoted a solution of the sulphur problem. As for the constituents of molten steel, it is taking too much for granted to mention the presence of FeS and MnS. If this infers that the melt contains diatomic molecules, the statement must be made that at least such molecules do not exist in the solid state at room temperature. Solid FeS crystallizes in the nickel-arsenide structure, and MnS (high temperature form) in the sodium-chloride structure. In these structures the sulphur is surrounded by six metal neighbors, and no molecular groups can be isolated. When sulphur is dissolved in molten steel, it is expected to maintain the same coordination number as in the solid state. We know that sulphur in steel has a certain chemical potential and a chemical activity which can be expressed by the reaction: S steel + H2 ? H2S where the activity A. is proportional to the ratio PH2S/Ph2. We know also that this activity is influenced by the presence of other constituents. For instance, there is reason to assume that carbon and silicon increase the sulphur activity and manganese decreases it. However, the exact relationship here is scarcely known, and further investigations are needed. Concerning the molten slags, if anything should be assumed a priori it would be that they are composed of ionic rather than molecular parts. There are indications of this in that solid silicates form ionic structures, and molten slags show high electric conductivity and can be electrolyzed.2 It has been claimed by Taylor and Chipman3 that their activity investigations

Jan 1, 1949