Search Documents

By Klaus Schwerdtfeger

The rules of solution of oxygen from H2O-H2-He gas and of nitrogen from N2-H2 gas in shallow melts of liquid iron were measured at 1610o and 1600o C, respectiuely. Concentration profiles were detemined in the liquid iron. Tire rate data indicate that the solution process is controlled by diffusion in the iron melt. The diffusivities for oxygen and nitrogen in liquid iron, as calculated from the present data, are DFe-o = (12 ± 3) < 10-5 sq cm per sec and DFe-N = 11 ± 2) X 10-5 sq cm per sec at the temperatures employed. AN attempt was made by Shurygin and Kryukl to measure the diffusivity of oxygen in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was measured. Assuming that the rate of dissolution of silica is controlled by diffusion of oxygen in the iron, the oxygen diffusivity was computed from the rate data giving Dfe-0 = 6.1 X 5 sq cm per sec at 1600°C. Although this value seems to be of the right order of magnitude, there is no proof of the correctness of the assumptions involved in the interpretation of these rate data. The oxygen concentration in the iron at the iron-iron silicate interface was taken to be that in equilibrium with the silica-saturated silicate melt. That is, it was assumed that no concentration gradient existed in the liquid silicate. This is a questionable assumption, unless it is proved that the thickness of the silicate layer is very much smaller than that of the diffusion boundary layer in the iron. Furthermore, Shurygin et al.1 used the Levich equation2 to interpret their rate data. This equation was derived for mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich&apos;s derivations. In the present work the diffusivities of oxygen and nitrogen in liquid iron were measured at 1610" and 1600oC, respectively. EXPERIMENTAL METHOD Iron melts contained in high-purity gas-tight alumina crucibles were reacted with H2O-H2-He gas for the determination of the oxygen diffusivity and with N2-H2 gas for the determination of nitrogen diffusivity. At the end of the reaction period, the samples were quenched in a cold H2-He gas stream at the top of the furnace. Oxygen or nitrogen contents in the iron were determined by chemical analysis. Two different types of diffusion experiments were perforxed. To determine concentration profiles, a few rate measurements were made using 4-cm-deep melts. The solidified samples were sliced into discs and each disc was analyzed for oxygen or nitrogen. In another series of experiments, oxygen or nitrogen was diffused into shallow melts (about 0.5 to 1 cm in depth) and the total sample was analyzed to obtain an average concentration of the diffusate. In most experiments, 4- to 5-mm-ID alumina crucibles were used. Some experiments were also made in smaller (3 mm) and larger (7 mm) diam crucibles. This variation in diameter caused no difference in the reaction rate, within the limits of experimental uncertainty. To promote the establishment of a stable density profile in the melt, all the samples were suspended in the lower end of the hot zone so that the top of the melt was hotter by a few degrees. Molybdenum wire resistance heating was used. The reaction tube of the furnace was a gas-tight recrystal-lized alumina tube. In most experiments the furnace was heated by an ac power supply. To check the possibility of inductive stirring, some experiments were carried out in a dc operated furnace, with essentially the same results. The temperature of the furnace was controlled automatically in the usual manner. The temperature was measured with a Pt/Pt-10 pet Rh thermocouple and is estimated to be accurate within ±5°C. The iron used was prepared by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zir-conia crucible. The main impurities are: Si 0.004 pct P, S <0.002 pct Cr 0.005 pct N 0.001 pct Zr 0.002 pct O 0.003 pct Mn 0.004 pct C 0.002 pct The gas composition was controlled by constant pressure head capillary flowmeters. Oxygen was removed from the gas mixture by passing it through columns of platinized asbestos (450°C) and anhydrone. Selected H2O contents were obtained by passing the purified gas through oxalic acid dihydrate-anhydrous oxalic acid mixtures held at constant temperature in a water bath. Water vapor pressure data for the oxalic acid dihydrate-anhydrous oxalic acid equilibrium were taken from the 1iterature.3 The flow rate used was about 1.5 liters per min. The whole system was checked for tightness at regular intervals.

Jan 1, 1968

By R. K. Matheson

THE Nivloc mine is 9 miles west of Silver Peak, Esmeralda County, Nevada. It has been operated by Desert Silver, Inc., since the summer of 1937. The cyanide mill treats 19o tons of silver-gold ore per day. In March of this year the main operations were about 2000 ft. west of the main shaft, which served as the downcast air passage for the mine. The mechanical blowers in use were sufficient to ventilate the west end at that time, but it was foreseen that as the mining area was extended ventilation would be an increasingly difficult problem, especially during the summer months. It was decided, therefore, to continue a raise from a point 100 ft. above the highest mining level (440-ft. level) to the surface; a distance of 443 ft. at approximately 65° From this point 40 ft. of drifting would be necessary to connect with a shallow shaft on the surface. (Fig. I.) All the raise was serviced from the 440-ft. level; costs and progress obtained in the initial 100 ft. are included in the following pages. CHOICE OF RAISE A raise in this locality would have four objects: (I) to provide an ample supply of fresh air to the working places; (2) to explore the vein from the highest mining level to the surface; (3) to provide waste fill for stopes in the area, and possibly provide a transfer for waste from the surface; (4) to provide an emergency exit in the west end of the mine. Before the mining of an ore shoot in the eastern part of the mine, a similar raise had been driven for purposes of ventilation and exploration. This raise and subsequent mining showed the vein to be noncommercial for a distance of about 250 ft. below the surface. However, in the area under operation, old surface workings showed occasional values. Thus from a development standpoint the raise was an excellent prospect. The raise chosen was a three-compartment, stulled raise having two chutes and a manway. The manway inside timber measured 4 ft. 8 in. by 4 ft. 6 in.; it carried air and water pipes, a ladderway and a slide for a timber skip. The two chutes would be used for drawing off the muck and the cleaning of the bulkhead, as well as for ore and waste passes, which would be especially useful for lateral exploration from the raise. The fairly large cross section of the raise (6 by 15 ft.) would provide a large quantity of waste for backfilling, and more could be obtained from a glory hole on the surface. TIME SCHEDULE As speed in completing the raise was the main requisite, three shifts were considered, but two shifts were decided upon when it was found that three would necessitate considerably larger fans than those available for clearing the raise. The main diffi-

Jan 1, 1942

The Library of the above-named Societies is open frond 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated front sources of information. To these the Library, through Its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining neaps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be, sent more promptly and in more usable shape.

Jan 1, 1917

By Culver, Richard S.

In spite of the widespread interest in rock bolt research, relatively little is known about the critical region surrounding the bolt anchor. In analyzing the stress distribution around an opening resulting from rock bolt support, it is commonly assumed that the bolt is fixed at a point far enough from the surface so that the anchor does not influence the performance of the bolt. Furthermore, a bolt anchor is assumed to per- form satisfactorily if it will hold the design load with a minimum amount of load relaxation, commonly called bleedoff. From the standpoint of the design engineer both of these assumptions are reasonable, but they ignore the fact that the extremely high stresses in the region of the anchor are capable of generating fractures in the rock. Lang estimated the bearing stresses for a slot and wedge anchor on a one-inch-diameter bolt to be as high as 125,000 psi. This paper describes a more thorough analysis of the magnitude of the stresses around the anchor and the nature of the potential fractures that might result.

Jan 1, 1968

By J. R. FINLA

THE three great war periods of recent times involving the-chief industrial, commercial, and military nations of the world have been the following: 1. Wars centering around the French Republic and Napoleon Bonaparte, .1791-1815;. involving every nation in Europe, parts of Asia Minor and *North Africa., and the United States of America. 2. Wars in Europe, Asia, and North -America beginning with the Crimean War, 1854-56, the British Empire, France, Sardinia, and Turkey against Russia; the Sepoy rebellion in India, -1857; -war of France . and Sardinia against ..Austria in Italy, .185.9; :the Taiping rebellion in China, 1861; Civil War in , America, 1861-65; French. occupation .of .M Mexico, .1863; Prussian war against :Denmark, :1864; (Prussia and Italy against Austria sand various -south German : states, 1866; :the Franco-German War, 1870.7,1.

Jan 1, 1931

By AIME AIME

T HE appointment of Herbert Hoover to the portfolio of Commerce in the President&apos;s Cabinet is to engineers the fulfillment of a long deferred hope to have an engineer in high political office and is a matter of congratulation to us for three reasons; because he is a mining engineer who represents the highest type of idealistic engineering effort; because he is a past president of the Institute; and because he has probably a broader grasp of world problems than any other living engineer. Frank A. Vanderlip in the preface to his book "What Happened to Europe" tells of the many interviews he had with the most prominent men in Europe which were made possible for him by his eminence as a banker and by the courtesy of the American ambassadors. He cites by name such well known figures as Austin Chamberlain, Sir Auckland Geddes, Monsieur Delacroix, Monsieur Briand, Mr. Padkrewski, Mr. Venizelos, Colonel House, General Pershing, Mr. Baruch, and many others and says :

Jan 1, 1921

By AIME AIME

SCANDINAVIAN countries seem somehow to furnish an amount of talent and leadership far be- yond their population and among them Sweden is possibly at the top. The United States has many eminent citizens born in the latter, country or who are of Swedish descent and the engineers may claim their full share. In fact, the number is so large that a flourishing Swedish-American Engineering Society has been formed, including a number of A. I. M. E. members. Dr. Waldemar Lindgren is more scientist than engineer, though his work in economic geology has contributed directly to the development of many mines, and he is the valued- adviser of a number of our larger companies. Probably he, himself, values most highly the contributions he has been able to make to scientific theories of the occurrence and genesis of ore deposits. His fellow scientists have placed upon these the high mark of approval by electing him to the National Academy of Sciences, and Princeton University in 1916 recognized his position by conferring on him the degree of Doctor of Science.

Jan 1, 1931

The Library of the above-named Societies is open from 9 A.M to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should he made as definite as possible so that the information received may he what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 6, 1918

By I. Sheinhartz, H. M. McCullough

DURING the course of a lubrication study in relation to the compacting of metal powders, it became desirable to measure the thickness of sprayed graphite coatings on steel dies for hot pressing. The thickness of these lubricant coatings ranged between 0.0001 and 0.002 in. In their particular case, the authors were interested in a method for measuring the lubricant thickness on tapered die inserts having curved surfaces. The lubricant was sprayed on the inserts at an elevated temperature and it was desirable to measure the thickness as soon as possible after application. Various standard types of commercial equipment were tried. Most of the available devices operated on either a mechanical or magnetic principle. The mechanical devices, such as micrometers, dial indi-

Jan 1, 1956

By Howard A. Meyerhoff

AS a source of mineral wealth, the larger islands of the West Indies have never had an enviable reputation. The Spaniards took possession of them in the sixteenth century hopeful that they would yield gold; but it was not long before they knew the rather rigid limitations of Antillean gold production and were seeking-and finding ---richer deposits of the precious metals in Mexico and on the west coast of South America. Although a great deal of wealth changed hands in the West Indian islands in subsequent years, the fact may be laid to the abundance of pirates and privateers and not to the richness of local ore bodies.

Jan 1, 1941

By Zay Jeffries

OF the new production of non-ferrous metals in 1930 gold will rank first in value. We usually think of copper as the most important non-ferrous metal. The copper industry as a whole, that is, adding copper production to copper fabrication, is the largest non-ferrous metal industry. Prior to the world war; however, gold led in value of new metal produced. During the war copper passed gold in value, but gold regained its position during the 1921 depression. For the past several years copper has again passed gold, but in 1930 gold promises again to regain the lead. The gold producer has at times been called a social parasite, largely because we &apos; cannot eat or drink gold, or because we cannot use it for clothes or for the construction of buildings. Let us briefly examine this accusation.

Jan 1, 1930

By R. W. Raymond

AT the Pittsburg meeting of the Institute, in March, 1910, the death of Mr. Metcalf was announced, and Col. H. P. Bope, of Pittsburg, delivered in memory of him a brief but eloquent address, which, though expressing the sorrow of Mr. Metcalf&apos;s friends, and, in general terms,. the debt of gratitude which his country and his profession owed to him, was not intended to be a complete survey of his life and work. With Colonel Bope&apos;s permission, and with the aid of some of the statements in his address, I substitute for it, in our Transactions, this more detailed, yet still inadequate memorial. As Colonel Bope justly remarked, the men who could do justice to this theme-such men, as Jones, Chalfant, Bennett, Oliver, and Park-passed away before Metcalf, leaving him almost the last of the generation of great steel-makers who made Pittsburg the Sheffield of America, and who discharged a double function, as the rear-guard of the old metallurgical practice and the van-guard of the new. I knew many of them; would that I were better qualified to celebrate their achievements. William Metcalf was born Sept. 3, 1838, at Pittsburg, Pa., where his father, Orlando Metcalf, was an eminent member of the bar. At the age, of sixteen, he entered the Rensselaer Polytechnic Institute, at Troy, N. Y., from which he was graduated in June, 1858. Returning to his native city, he became an assistant engineer in the Fort Pitt Foundry, of which. he was made Superintendent in 1859. This famous establishment produced the largest castings and heaviest machinery then known in the United States;-and Mr. Metcalf&apos;s intense, intelligent and incessant study of his business prepared him as a manufacturer for a patriotic service to his country more valuable than, as a soldier, he could have rendered in the field. The call came in 1862, when the government needed, above all things, a supply of field, naval and siege artillery. The

Apr 1, 1911

By David Moskowitz, Ira Binder, Robert Steinitz

THE hard refractory borides of the transition elements of the 4th, 5th, and 6th groups of the Periodic System have been the subject of a number of recent investigations.&apos;-&apos; It is well known now that most of these elements form several different borides, and Kiessling8 has summarized the rules which govern to some extent the arrangements of the boron atoms in the various structures. Melting points of a few borides have been published." The systems Fe-B, Ni-B, and Co-B have been reported," but, as these borides are rather low melting, they are outside of the groups of boron compounds considered here. Brewer&apos; has tested the stability of various borides and estimated a number of eutectic temperatures between different borides, but in no case was the complete system of a transition metal and boron investigated. The phase diagram becomes of special importance if the preparation of the borides from the elements in powdered form is considered; the lowest eutectic temperature will determine the first appearance of a liquid phase. Also, the knowledge of high temperature phases, if they exist, is important for the preparation of bodies from these borides by hot pressing or sintering. During the investigation of various metal borides,7 it was found that there were more boride phases existing in the Mo-B system than reported by Kiessling." They occur, however, only at temperatures above 1500°C and were, therefore, not found by him. This led to a study of the equilibrium diagram of the Mo-B system. ranging from 0 to 25 pct B and from room temperature to the liquidus. Part of this investigation was reported during the "Research in Progress" session at the 1952 Annual Meeting of the AIME.11 Raw Materials and Preparation of the Borides The raw materials used were commercial molybdenum and boron powder, both supplied by the Molybdenum Corp. of America. The molybdenum powder was 99+ pct pure? while the boron powder contained about 83 to 85 pct B. A large percentage of the impurities in this powder was oxygen, with the rest formed by iron, calcium, and unknown substances. The low purity of the boron used was, however, not considered detrimental to the final product, as most of the impurities evaporated at the high temperatures at which the borides were formed. The final product always had a minimum purity of 96 to 98 pct (figured as molybdenum and boron), with carbon, iron, and probably oxygen being the remaining products. Carbon is usually present as graphite. The chemical analyses always confirmed the compositions which corresponded to the crystallographic structures as determined by X-ray diffraction, and the boron content of the finished product agreed closely with that of the starting mixture; no boron was lost during the boride preparation. The chemical analysis methods employed for molybdenum and boron were previously described by Blumenthal.12,13 The powders were mixed by hand in the desired proportions, compressed at room temperature under low pressure, and then heated under hydrogen to about 1500" to 1700°C in a graphite crucible to form the borides. Usually, the three well-known borides Mo,B, MOB, and Mo,B,, which are stable at room temperatures, were prepared in this way, and all other compositions were made by mixing these borides in various ratios or by the addition of molybdenum or boron powders for the very low or very high boron contents. Preparation of two-phase compositions directly from the elemental powders was tried only occasionally to check whether equilibrium could be reached in this way. Experimental Procedures The stable borides were mixed in the desired ratios and heated under hydrogen in graphite crucibles to various temperatures. The well insulated crucibles were heated in a high frequency induction furnace. Special care was taken to obtain exact temperature measurement, which proved much more difficult than originally anticipated. It is believed that individual temperature measurements have an error of less than ±25ºC, while melting or transformation temperatures are accurate within ±50°C. The temperatures were measured with an optical pyrometer which was aimed at the closed end of a graphite tube extending down into the crucible. close to the samples. Attempts to measure directly through the hydrogen exit stack failed. The crucible arrangement is shown in Fig. 1. Heating was done at a slow rate to be sure that the temperature inside the crucible was uniform. The specimens were kept at the final temperature for about 30 min. For the investigation of high temperature phases, some samples were quenched. They were heated, without atmosphere protection, in a very small graphite crucible which could be rapidly removed from the high frequency coil, and dropped into water. These quenched samples were afterwards annealed to establish the equilibrium at lower temperatures. The melting points or the positions of the solidus and liquidus lines were determined by heating the specimens to various temperatures and examining them at room temperature for evidence of a liquid phase. These results were checked later on by thermal arrest curves, especially to determine the exact position of the eutectic temperature line. For this purpose about 200 g of the boride were melted in a graphite crucible, in an arrangement similar to Fig. 1. Slow cooling was assured by very good

Jan 1, 1953

By John Chipman, Theodore B. Winkler

IN order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chipman,3 dealt with the simplest possible slag system that would resemble those found in the basic open hearth-the slag system consisting of CaO-MgO-SiO2-FeO. (Taylor&apos;s rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemistry of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, Si02, FeO, Fe203, P205, MnO, A1203 and CaF2, but not all of the slag samples contained all of these components at one time. REVIEW OF LITERATURE Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Brings4&apos; von Samson-Himmelstjerna,5 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution ratios

Jan 1, 1946

By E. W. Murbach

The oxidation of uranium carbide by oxygen at various pressures, and by air, has been investigated at temperatures up to 600°C. Arc-melted and cast uranium carbide displays oxidation behavior that appears to be dependent on its treatment after melting. ccReactive" uranium carbide, which results from exposure of freshly melted material to laboratory air, ignites in oxygen at about 275° to 350°C depending on pressure, and in air at about 350°C. The product of the initial oxidation appears to be UO2+.. Continued heating produces U30,. The initial oxidation rate is poportional, roughly, to the square root of the oxygen pressure. The activation energy determined for the initial oxidation reaction is 7.1 kcal, from 400° to 600°C in 10 mm of oxygen. AN investigation of low-decontamination methods for reprocessing uranium carbide reactor fuels is being carried out at Atomics International. One of the reprocessing cycles includes oxidation of the fuel at relatively low temperature (300° to 500°C) and reaction of the product oxide with carbon at elevated temperatures (above 1500°C) to produce uranium carbide. A number of small-scale experiments have been carried out in which uranium carbide was oxidized in air and oxygen at various pressures to measure reaction rates and to obtain other information concerning the oxidation process. In initial experiments with arc-melted UC, ignition was observed at about 275°C in oxygen or 350°C in air. However, similar experiments by Neymark&apos; at 426°C in air showed no ignition. It was soon determined that the difference in oxidation behavior was due to the treatment of the UC following arc-melting. Neymark&apos;s experiments were carried out with freshly melted UC while those reported in the

Jan 1, 1963

SAN FRANCISCO SECTION Roy H. ELLIOTT, Chairman - T. A. RICKARD, Vice-chairman W. H. SHOCKLEY, Secretary-Treasurer, 959 Waverley St., Palo Alto, Cal. D. A4. RIORDAN C. F. TOLMAN, JR. A joint meeting of the local sections of the several national engineering societies represented in San Francisco was held at the Engineers&apos;. Club on Thursday evening, Sept. 26, 1918. The subject for the evening, "Fuel Conservation," was ably discussed by a-number of representatives of the Federal Administration and by engineers interested in the generation and utilization of all kinds of power on the Pacific Coast. The following extracts from papers presented at this meeting have been selected as being of the greatest interest and value to members of this Institute. Problems of the Fuel Administration ALBERT E. SCHWABACHER.-America&apos;s war needs call for 100,000,000 more tons of coal this year than in 1917, and 200,000,000 tons more than in 1914, when the war started, and this increase must come from a weaker man-power than that of 1917. It must be transported by a railroad system that has not been improved since the war started, and has been burdened with inconceivably greater demands than were made upon it before the war. This tremendous increased demand must be met by most intensive work in three directions; increased production, efficient conservation, and a distribution system which will insure against lost motion. While every European country has decreased its coal production since the war began, the United States has mined 50,000,000 tons more coal, during the first year of the war, and will increase this by another 50,000,000 the present year. Every 8 days there are being mined and transported as great a weight of coal as of the entire wheat crop of the United States. Of the 735,000,000 tons of coal which must be made available for consumption by our railroads, ships, war industries and people, 100,000,000 tons will come from the anthracite fields, the remainder from the bituminous fields. In 1917 there were produced about 330,000,000 bbl. of oil, and this year an additional amount over last year&apos;s production, of approximately 23,000,000 bbl. will be required. Water power developed 5,000,000 hp., the demand greatly exceeding the available supply.

Jan 12, 1918

By Leon Orlowski

THE oil-bearing districts of Poland are found on the slopes of the Carpathian Mountains. The oil belt extends from Gorlice southeast to Stanislawow. It is approximately 250 miles long and 30 miles wide, and comprises four geological districts: the western, or Gorlice district; next, to the east, the Krosno district; the Boryslaw district; and, in the extreme southeast, the Stanislawow district. The amount of petroleum produced in Poland from the beginning of the oil industry scarcely totals 26,000,000 metric tons, or 15 per cent. of the estimated supply. Of this amount, 18,000,000 tons have been taken from the fields of Boryslaw within 25 years; and only about 8,000,000 tons from all other fields within a period twice as long, although some of these other fields represent just as good possibilities as did Boryslaw at the beginning of its development. The Polish oil industry was severely stricken by the war. The retreating Russian armies, in 1915, destroyed a large number, of the existing oil wells, nor was the post-war period favorable for the development of this industry;; the money and credit stringency interfered with the expansion of drilling. But since 1921 there has. been a slow steady increase in production and there is now every reason to believe that conditions in the industry will improve. In fact, an increase in new drillings has been reported for the current year. The production of crude oil in Poland, in 1913, amounted to 1,113,668 metric tons. In 1914, the production declined- to 655,600 metric tons. In 1921, the production was 705,596 tons; in 1922, 712,428 tons, and in 1923, 737,182 tons; or more than 5,000,000 bbl. But the fields have a much greater potential output, which could be realized were the capital available for prospecting and new drilling. The principal producing, and at present most exploited, fields are around Boryslaw and Schodnica. These fields were developed rapidly for in the first year of their modern exploitation the wells were gushers of moderate depth. However, as a result of heavy drilling, the shallow folds have been exhausted and oil can be reached now only by deep drilling. Wells of almost 5600 ft. have been drilled in Boryslaw. Because of these drilling conditions, a large number of engineers and workmen specially skilled in deep drilling are to be found in this field.

Jan 3, 1925

By Nicholas J. Grant, Oliver Preston

PUBLICATION of data by Irmann&apos; indicating outstanding thermal stability and elevated-temperature strength properties in a sintered aluminum powder product (SAP) stimulated interest in the strengthening of metals by means of a highly dispersed oxide phase. This material was produced by compacting, sintering and extruding a fine flake aluminum powder, resulting in a dense product containing 10 to 16 volume pct alumina, which arises from the thin oxide film on the starting powder, highly dispersed in a matrix of pure aluminum. The method of producing SAP, and the stable high-temperature properties obtained from it, introduced the possibility of developing superior materials for high-temperature service by powder metallurgy methods. The composition of the materials of this type which are presently under consideration is predominantly metallic, containing from less than 1 pct up to about 20 volume pct of the oxide. As a result, other properties of these materials, such as electrical and thermal conductivity, thermal shock resistance, and to a certain extent ductility, notch sensitivity, machinability and hot working properties, are also predominantly metallic. These alloys do not constitute, therefore, a completely new class of materials as do the cermets, but rather present a new means of modifying the properties of a metallic matrix. In this sense, SAP type alloys are more closely analogous to the alloy aging systems. While the strength properties realized in the oxide-pure metal systems at the lower temperatures are substantially less than the best attainable in the aging systems, the thermal instabilities in the latter make them of less value for use at temperature much above their optimum aging temperatures, as indicated in Fig. 1. While the means of obtaining an oxide dispersion are more difficult and costly than conventional aging processes, in the light of the as yet limited understanding of such systems there is considerable promise of improved high temperature properties arising from the thermal stability of these structures. Since the development of SAP in 1946, its properties and the properties of a series of similarAl,O,-A1 products containing from about 1 to 20 pct aluminum oxide have been fairly extensively studied and reported.&apos;- "articular attention has been given to

Jan 1, 1958

By Raymond L. Jones

With the inauguration of open-pit copper mining in Bagdad, Ariz., plans were formulated for a large scale leaching operation. Dump stockpiling was started almost immediately, but actual production was not initiated until spring 1961.

Jan 9, 1977

"Butte originated as a placer mining camp. The first gold discovery was made in the year 1864, near what is now Main Street. Placer mining was vigorously prosecuted along Silver Bow Creek and in Missoula, Buffalo, Town and Parrot gulches for a period of five years, at the end of which time, in 1870, the camp was practically deserted. In the meantime, the quartz veins so prominently traceable over the hillsides were located, the first location being made by W. L. Farlin and called the Black Chief claim, and later restaked as the Travona. Reasoning from the presence of the gold placers, free-milling gold ores were eagerly looked for by the early prospectors. Claims covering the great Rainbow and other silver lodes were located in the sixties. The presence of valuable silver ores in these veins caused the staking out of many claims, believed to be valuable only for silver, but which later proved to be enormous copper producers.Treatment of these early discovered rich ores was first attempted in arrastres. Later, stamp mills were built. The Centennial dropping 10 stamps, was the first, and in 1875 Mr. Farlin built the Dexter 10-stamp mill, intro¬ducing chloridizing-roasting. More successful processes were soon introduced and several large mills built, among which were the Alice, Lexington, Silver Bow, Moulton and Bluebird, in all representing a total of 290 stamps. The silver mining industry reached its zenith in 1887 and declined rapidly in the early nineties, following the sudden drop in the price of silver in 1892.During this period of silver mining activity the business of copper mining was making rapid strides. Development of the veins, located as silver veins, had uncovered copper ore in many instances. There was great activity in ""claim staking'' in the years from 1871 to 1879, during which period most of the claims covering the present productive copper area were located."

Jan 1, 1913