Search Documents

By Kazuyo Yokoyama

New environmental assessment model based on the Waste Input-Output analysis has been developed and applied for the "Landfill mining activity". "Landfill mining" implies the digging up of the landfilled wastes, the recovery of valuable material and energy resources and, thus, the reuse of the saved space as a new landfill site. In this study, the landfilled wastes are assumed to be treated by the gasification/melting processes. Two kinds of reactors, the fluidized bed type (FB) and the shaft furnace type (SF), have been considered in this work as the typical gasification/melting processes adopted in Japan. In FB, the dug-up wastes are heated in the sand fluidized bed zone under reducing atmosphere, Fe and Al are recovered in the metallic form, and then, the gasification/melting of residues is made in the second zone. In SF, the waste is charged in the high temperature coke bed, and the gas is recovered together with molten metal and slag. Both processes generate electric power by the recovered heat and fly ash as waste to landfill. It has been found in this study that the both processes can reduce the total volume of waste and save the available landfill space. SF seems to have higher potential for decreasing volume of wastes because of less emission than FB while FB has great benefit to recover metallic Fe and Al individually. The results of scenario analysis have also indicated that the landfill mining activity is effective for sustainable management of landfill sites.

Jan 1, 2006

By Fernanda Margarido

Recovery of metals contained in the electrode materials of batteries was studied considering an integrated recycling process constituted by physical and chemical operations. The physical treatment included the shredding of the spent batteries, followed by a wet sieving operation of the fragmented material. The physical behavior of Ni-Cd and Zn-Mn based (alkaline and saline) system batteries was studied and compared. In that sense, shredding operation was performed and the sieving of shredded fractions was accomplished to evaluate the efficiency of the separation of electrodes and scrap. For Ni-Cd batteries the loss of electrode material with the supra fraction (scrap) after the shredding operation was lesser than the Zn-Mn batteries. Especially for saline-type batteries, the electrode attached to the scrap was substantial leading to important losses. This difference can be explained by the composition of the case materials and the internal physical constitution of the electrodes. The wet sieving studies carried out allowed optimizing the separation of the electrode fine fractions from the scrap materials through the analysis of selectivity Cd/Fe or Zn/Fe. For Ni-Cd batteries, maximum selectivity was achieved for the granulometry of 1.4 mm, while for alkaline and saline systems best selectivity were obtained at 2.8 mm and 5.6 mm, respectively. This process allowed the recovery of about 70% of electrodes for Ni-Cd and alkaline systems, and 50% for saline batteries, with less than 5% of scrap as contaminant. This physical step can be considered as a pre-treatment of this type of waste material envisaging its valorization by chemical treatment, as improves the concentration of the elements of interest and decreases the iron content.

Jan 1, 2006

By De-qing Geng, Guang-liang Wu

The waste slag generated by the LF refining process of Q345B low alloy hot-rolled steel, still has some refining capabilities. If recycled, it can reduce environmental pollution, and save the economic costs. A research on melting Characteristics of Q345B steel LF refining waste slag was investigated by using orthogonal experimental method, and the effect laws of composition on that were analyzed. Through variance analysis and significance criterion, it is concluded that the optimum ingredient of the regenerated LF refining slag is 25%A12O3, 12%CaF2, 7%MgO and R= (CaO)/ (SiO2) =2.5. And the regression analysis is carried out by using SPSS software, to get the mathematical relationship between ingredient with high reliability and melting temperature of refining slag T=1451.3-6.25CaF2+2.36 R.

Jan 1, 2016

By J. -P. Nepper

It has been possible to largely contain converter aisle emissions of SO2 and fumes in the case of batch-wise operated Peirce Smith converters during normal blowing periods with the help of suitably designed primary hoods. Controlling the escape of off-gas during the periods of turning the converter in or out of the stack has been problematic in the past. Effective automated contro1 systems have been deve1oped for the purpose and successfully applied in smelter operations in Spain, Taiwan and Germany. This has led not only to an effective reduction of emissions in the converter environment but also to an improvement in the converter operation.

Jan 1, 1992

By Matti Leiponen

During the last few years Outokumpu Oy has put forth efforts to develop the material handling in the Pori tankhouse. The final objective is full automation including cell loading. The fully automated material handling provides high quality anodes and cathodes as well as equipment and handling systems capable of very accurate cell loading. The new machines and equipment for accurate cell loading and the methods to produce high quality anodes and starting sheets are described in this paper.

Jan 1, 1987

By Sridhar Komarneni

"Microwave-hydrothermal processing is a novel technique which combines the conventional hydrothermal processing with microwave field and we previously showed for the first time, that ceramic powders can be rapidly produced by this technique. This review paper deals with the synthesis of unary oxides such as Fe203, Ti02, Zr02, etc., binary oxides such as BaTiO3, SrTiO 3, PbTiO 3, SrZrO 3, KNbO3, etc., and ternary oxides such as NaTi2 (PO4)3 and pyrochlore phases of Pb(Mg1/3Nb2/3)O3, Pb(Zn1/3Nb2/3)O3 etc. and metal powders such as Cu, Ni, etc. below 195°C. This method can be adopted to the synthesis of a large variety of powders by the appropriate control of pH, Eh, temperature/pressure and concentration of chemical species. The main advantages of this method compared to conventional hydrothermal processing are (a) it increases the kinetics of reaction by one to two orders of magnitude, and (b) it can lead to novel phases especially those with layered structures.IntroductionConventional hydrothermal processing is a well-established synthesis technique which has been extensively used in the preparation of fine ceramic powders [1-5], large single crystals [6-8] and massive cement blocks [9]. Technologically important ceramic powders such as BaTiO 3, Al203 etc. made by the hydrothermal process are now commercially available. Although there are numerous methods for materials synthesis, hydrothermal method is truly a low temperature and environmentally benign process. For example, ZrSi04 (Zircon) which is extensively used in ceramic industry can be prepared hydrothermally at 150·C [10] compared to sol-gel or solid-state method [11,12] which require a temperature of about 1000·C. The hydrothermal method is environmentally benign because hydrothermal reactions are carried out in closed systems at low temperatures and the contents can be recovered and recycled after cooling to the ambient conditions. One of the disadvantages with any low temperature processing method is slow kinetics. For this reason we have combined the hydrothermal method with microwaves to enhance kinetics and we named this method as ""Microwave-hydrothermal"" processing [13- 16]. Although the combination of microwave and hydrothermal techniques has been used in the past few years to dissolve all kinds of inorganic (e.g. alumino silicate rocks) and organic materials rapidly for chemical analysis, we were the first to show its potential value for the synthesis of various ceramic powders [13-16]. In this paper, I show that this novel method is applicable to the synthesis of all unary, binary and multinary oxides by the appropriate control of pH, Eh, temperature, pressure and concentration of chemical species. In addition, this method is also found to be useful for the preparation of metal powders."

Jan 1, 1994

By T. Langthaler, H. W. Engl, H. Holl, K. L. Schwaha

"The trend towards near net shape casting requires the development of more complex design and control algorithms for continuous casting ""machines in particular with respect to the solidification process.Compared to conventional continuous casting the reduction in casting thickness allows to influence more directly the solidification rate by control variables like surface cooling and/or casting speed.In order to enable the determination of these control variables for a given solidification profile, an algorithm (inverse solidification analysis) has been developed based on nonlinear constrained optimization. The application of the model is illustrated by practical examples ranging from conventional continuous casting to advanced thin slab casting.IntroductionProcess development in the Iron and Steel Industry is directed towards the realization of continuous process sequences. Since the direct linkage of processes imposes some restrictions onto the individual process steps, more complex algorithms are needed for design of equipment and control of operation. In particular the recent trend to reduce casting thickness, i.e. to cast thin slabs, has made the direct coupling of continuous casting and rolling absolutely necessary. The prospective development in strip production is schematically shown in fig. 1."

Jan 1, 1988

By C. M. Iheagwara

This paper has addressed the issues that constitute major obstacles to the cost- effective and efficient operation of metallurgical vessels from the refractory standpoint. Refractories generally withstand severe conditions of high temperature reactions as well as physical loading/impingement and hence degenerate and need replacement. Scarcity of some refractory materials especially high alumina and magnesite ores in some places, the prohibitive cost and the frequency of replacement of damaged refractories threaten the continued support for metallurgical operations. Some of the causes, prevention and cure for refractory wear have been discussed and rational strategies (short and long term) have been recommended which if implemented should go a long way towards arresting the perennial problems they portend.

Jan 1, 1991

By James D. O, DeLa&apos

Multicomponent materials are common in nearly all areas of materials science and technology, yet the use of phase diagrams to represent these complex systems is hampered by the requirement of three or more dimensions for explicit graphical representation. In the present work, the "solid-modeling" capabilities of a computer aided design (CAD) system have been applied to the representation of three-dimensional phase diagrams. Relevant phase diagrams for a hypothetical quaternary eutectic system were constructed and used to demonstrate the capabilities of the technique. These capabilities lead to relative ease of phase diagram construction and improved access to qualitative and quantitative information. Results of this work are contrasted and compared to previous efforts toward computer ,representation of phase diagrams. It is concluded that solid-modeling of three-dimensional phase diagrams can be used to advantage in both education and research.

Jan 1, 1991

By C. Beckermann

"A diffuse interface model is derived for the direct simulation of two-phase flows with surface tension, density differences between the phases, and phase change. The derivation starts from the balance equations for a sharp interface and uses a formal averaging procedure on an atomic scale to obtain diffuse interface versions of the equations. Two approaches are considered: (i) the two phases have different velocities inside the interface and separate conservation equations are solved for each phase, and (ii) the two phases have the same velocity inside the diffuse interfuce and mixture conservation equations are solved. Based on a superposition of microscopic (atomic-scale) and macroscopic interface morphologies, an expression for the interfacial momentum source term is introduced that models surface tension effects and accounts for immiscibility between the phases.IntroductionDiffuse interface methods have been a popular tool in the direct simulation of two-phase flows [I]. In diffuse interface approaches, the interface between the two phases is characterized by a rapid but smooth transition in the properties, such as density and viscosity. Usually, a phase function ? is introduced to represent this transition, and the evolution of ? in the domain is computed from a separate equation or recipe. A unique set of conservation equations (e.g., mass and momentum) is solved on the entire domain, irrespective of the phase present, by accounting for the transition in the properties and introducing terms that account for interfacial sources. The continuum surface force (CSF) model of Brackbill et al. [2], which accounts for surface tension, is an example of the latter. The volume-of-fluid (VOF), level set, and phase-field methods are all examples of diffuse interface approaches. The major advantage of diffuse interface methods is that explicit tracking of the interface and the application of traditional sharp interface conditions are avoided. A disadvantage can arise from the artificial smearing of what is in reality an interface of atomic-scale width; however, techniques have been developed to overcome this problem."

Jan 1, 2004

By Soobhankar Pati

Solid oxide membrane (SOM) technology has been successfully employed for the production of high energy metals such magnesium, titanium and tantalum by directly reducing their oxides. This paper reports on the recent investigation done for calcium production by SOM process from calcium oxide, dissolved in fluoride and chloride based fluxes. This process employs an inert oxygen-ion-conducting stabilized zirconia membrane to separate the inert cathode in the flux from the anode. When the applied electrical potential between the electrodes exceeds the dissociation potential of calcium oxide, oxygen ions are driven out of the melt and through the zirconia membrane to the anode where they are oxidized. Reduced calcium metal deposits or evolves at the cathode depending on the operating temperature. The SOM cell has been electrochemically characterized, and key concepts related to CaO dissociation, leakage current, solubility of Ca in the flux, and hygroscopic nature of the flux relevant to the SOM process are explained.

Jan 1, 2008

By Larry Twidwell, Ed Rosenberg, Courtney Young, Sean Dudley, William Gleason, Maureen Chorney

Experimental and industrially produced polystyrene and silica resins are tested for recovery capabilities of Rare Earth Elements (REE). Testing regimes being used are typical of resin analysis. Inductively Coupled Plasma-AES results indicate that preferential separation and recovery is possible in the adjusted pH range of2 to 10, solution conditions, and resin type. Testing conditions are resulting in structure modification of the composite resin as indicated by X-Ray Diffraction, Differential Scanning Calorimetry, Scanning Electron Microscopy, Mercury Porisometry, and density analysis. Resin modification indicates both surface and internal structure alteration outside of reported standard behavior of resins. Structural changes have ramification for both Rare Earth Recovery RER and traditional resin operations. Analysis shows that the resin uptake of REE can be manipulated for concentration. Further analysis with SEM work indicates that widespread surface and interior modification is taking place as resins load with REE. This modification is leading to pore rupture and particle breakage. Further investigation is being performed to determine the mode of breakage.

Jan 1, 2015

By llya Perederiy, Vladimiros G. Papangelakis, Indje Mihaylov

"Nickel slags obtained from various smelting furnaces and converters differ in terms of their chemical composition and microstructure. The microstructure of the slag is largely affected by how fast the slag is cooled after being discharged from the furnace. Slow cooling is known to promote crystallization and growth of phases such as crystalline fayalite (Fe2Si04), magnetite (Fe3Ü4) and vitreous silica (S1O2). Slag granulation causes rapid solidification of the melt in the form of either an amorphous solid or highly intergrown crystalline silicate and oxide phases. Smelter slags contain entrapped Ni, Co and Cu in the form of dissolved oxides and matte inclusions. Extraction of the entrapped metals by high pressure oxidative acid leaching (250°C, 70 g/L initial H2SO4, up to 90 psi O2, 45 min) relies on the dissolution of the metal bearing minerals. The impact of the slag microstructure on the accessibility of these minerals to leaching, as well as the morphology of the produced residues is discussed in this paper.IntroductionIt was shown previously that entrapped base metals can be efficiently extracted from naturally cooled (as opposed to granulated) crystalline nickel smelter and converter slags using high pressure oxidative acid leaching operating at 250°C, ~40 g/L terminal acid and 60 to 90 psig oxygen overpressure [1, 2,3,4, 5, 6].Mineral characterization work performed on a naturally cooled crystalline nickel furnace slag from Vale's operations in Sudbury (ON, Canada) was previously reported [4]. Fayalite (Fe2Si04) and magnetite (Fe3U4) were detected using powder X-ray diffraction. These two minerals as well as silica (S1O2) and matte ([Fe,Ni,Cu]Sx) were also identified with the help of energy dispersive X-ray spectroscopy (EDX) on cross-sectional images obtained with a scanning electron microscope (SEM) operating in the backscattered mode. Nickel converter slags obtained from Vale's operations in Sudbury were found to be mineralogically similar to the furnace slag, but with higher contents of matte entrainment and magnetite based on the SEM-EDX observations [6]."

Jan 1, 2012

By Marcela C. Santini, Luiz A. Teixeira

"Surface conditioning (also referred as etching) of plastics prior to metallization is generally conducted with sulfuric I chromic acid solutions. Although these baths perform well technically, the presence of Cr (VI) imposes serious operating problems of an environmental nature. The present work reports ·the results of a study of surface conditioning o(ABS using solutions based. on sulfuric acid, with hydrogen peroxide and/or nitric acid, replacing chromic acid, as oxidants. Process performance was evaluated by SEM and by the uniformity and adherence of electroless nickel coatings applied on selected conditioned samples. The results showed that the evaluated types of solutions could be optimized to perform as well as the chromic-based baths, with a much superior environmental quality.IntroductionMetallization of plastics is normally undertaken for either decorative or functional purposes. Through metallization, the specific properties of plastics such as light weight, design flexibility, and low-cost of manufacturing are enhanced by the addition of properties usually associated with metals. These include reflectiveness, abrasion resistance, electrical conductivity, and a variety of decorative effects (1).The available processes that can be used for metallization of plastics are vacuum metallization or vapoµr deposition; indirect metallization and plating (1). Plating can be sub-divided into electroless plating and electroplating. In electroless plating, metal ions in aqueous solution are deposited on the .activated plastic surface by oxi-reduction reactions without the aid of an external electric potential, forming a thin metallic layer. This electroless deposited film has two functions: (a) it provides an electrically conductive substrate that allows further coating by electroplating; and (b) provides a secure bond between the plastic substrate and the electroplated layer (1,2). In case the electroless metallic part requires an additional layer for finishing purposes, or just an increase in thickness, the part can be additionally electroplated with a· variety of metals - in most cases those are copper, nickel or chromium (3)."

Jan 1, 2000

By Pertti Koukkari, Nagendra Tripathi, Karri Penttilä, Justin Salminen

A computational fluid dynamic model for a novel flash ironmaking process based on the direct gaseous reduction of iron oxide concentrates is presented. The model solves the threedimensional governing equations including both gas-phase and gas-solid reaction kinetics. The turbulence-chemistry interaction in the gas-phase is modeled by the eddy dissipation concept incorporating chemical kinetics. The particle cloud model is used to track the particle phase in a Lagrangian framework. A nucleation and growth kinetics rate expression is adopted to calculate the reduction rate of magnetite concentrate particles. Benchmark experiments reported in the literature for a nonreacting swirling gas jet and a nonpremixed hydrogen jet flame were simulated for validation. The model predictions showed good agreement with measurements in terms of gas velocity, gas temperature and species concentrations. The relevance of the computational model for the analysis of a bench reactor operation and the design of an industrialpilot plant is discussed.

Jan 1, 2014

By M. Tokumasu, T. Mutoh, Y. Sugawara

"In October 1986, a process computer was introduced in order to achieve an optimum combustion of pulverized coal at the reverberatory furnaces. The secondary combustion air volume is controlled based on the nitrogen oxide concentration of the off-gas from the reverberatory furnaces. The carbon monoxide concentration has strong relation with the concentration of nitrogen oxide under the situation of using alternative fuels, such as chipped tires and p,ulverized coal. Using this computer aided combustion control system, both nitrogen oxide and carbon monoxide concentrations were stabilized and conventional monitoring and controlling apparatuses were absorbed into this computer system. Due to this easily operated system, labor cost was reduced and the operation of the reverberatory furnaces and the off-gas treatment plant became stable.IntroductionOnahama Smelter and Refinery started its operation in April 1965 as a large scale copper smelter and refinery in Japan. The green charged reverberatory furnaces were introduced and bunker C oil was chosen as the fuel for the reverberatory furnaces. After the oil crises, Onahama was forced to use cheaper fuels such as coal and waste tires, i.e., alternative fuels instead of the expensive oil. As the amount of the alternative fuels fed to the reverberatory furnaces increased, the concentrations of nitrogen oxide and carbon monoxide in the off-gas became unstable. Consequently, the fluctuation of the combustion condition became not to be negligible in view point of a combustion efficiency and pollution regulations. A process computer has been introduced to overcome these off-gas troubles and to reduce the operating cost of the smelter.Outline of Operation HistoryInitially, the operation started by one reverberatory furnace and then the capacity was expanded almost twice by additional furnace in December 1972. As shown in Figure I, the smelting throughput was depressed after oil crises in 1973 and 1978. From 1983 to 1985, some copper mines stopped their operations because of low price of copper metal. During this period, Onahama suffered from the shortage of concentrate production levels were depressed."

Jan 1, 1989

By I. K. Chopde, M. M. Dhobe, C. L. Gogte

"The quality of machined surface is becoming more and more important to satisfy the increasing demand of component performance and its reliability. While machining any component, it is necessary to satisfy the surface integrity requirements. Heat treatment plays an important role in improving the characteristics of the material.This work investigates the effect of heat treatment on the surface characteristics of AISI D2 tool steel after Wire-Electro Discharge Machining (W-EDM). The test specimens were prepared by hardening and tempering and then machined with Wire-Electro Discharge Machining process. Optical and scanning electron microscopy, surface roughness and micro hardness tests were conducted to study the surface characteristics of the machined surface. After characterization based on microstructures and test results, it is observed that the recast layer droplets are of smaller size with reduced white layer thickness resulting in higher hardness and lower surface roughness.IntroductionWith the development of mechanical industry, the requirement of alloy materials having high hardness, toughness and impact resistance is increasing. At the same time the quality of machined surface is becoming more and more important to satisfy the increasing demands of component performance and reliability. When machining any component, it is necessary to satisfy the surface integrity requirements. Surface integrity has two important parts. The first is surface texture, which governs mainly surface roughness. The second is surface metallurgy, which concerns to the nature of surface layer produced in machining [2]."

Jan 1, 2012

By Nagy El-Kaddah, Thinium T. Natarajan

A modeling strategy is presented for computing the electromagnetic field and the shape of the molten metal in electromagnetic confinement systems. This strategy involves the use of a hybrid finite element/integral technique to calculate the electromagnetic field and force distribution in the melt. The free surface shape is determined from minimization of electromagnetic, gravitational and surface tension energies using the Lagrange method of multipliers. This approach was applied to model the electromagnetic levitation melting process. The model was found to accurately predict the measured shape of levitated droplets.

Jan 1, 2014

By Keith Cramer

As a leader in the development of metal extraction technology, Avecia continues to pioneer advancements for the processing of copper through leach, solvent extraction, and electrowinning of copper. From the initial patent of the second generation of oxime 5- nonylsalicylaldoxime in the 1970's; to the effective use of modifier technology; and development of computer assisted modeling programs, Avecia is driving SX technology to maximize extraction productivity. Keys to consider when advancing productivity are: 1) high quality, high performance products; 2) a responsive, partnering approach to technical service; and 3) tools to aid in the education of industry wide technical personnel with a view on continuous improvement. The focus of this paper is on the advancement of tools to aid in the education for optimization of processing copper through solvent extraction. One such tool is Avecia's own customized solvent extraction modeling program called MEUM. MEUM is currently used world wide to analyze plant operations, test ideas for improving operations, assist engineering companies in design, and to teach basic solvent extraction concepts. Recently MEUM has also been incorporated into a University setting. In the spring of 2000 Avecia worked with the University of Melbourne to integrate MEUM into their Mass Transport tutorial class. Students completed exercises to evaluate how operational changes affected a solvent extraction plant's performance. This paper introduces the basic functions of the program and discusses the successful implementation of MEUM into the University of Melbourne curriculum.

Jan 1, 2002

By Olli Järvinen

The capacity of the Outokumpu Pori refinery is today about 125 000 mt in 1998. The anode slime amount is about 700-800 mt. The copper is removed with pressure leaching. Selenium roasting is done with the gas roasting. The doré smelting in the furnace is done with the tilting rotating converter with oxy-fuel burner (TROP). Doré anodes are treated in the silver electrolysis. Gold is recovered from the gold mud with the quick hydrochloric acid leaching process. The important point in the leaching is to get into contact the solid copper with the oxygen and liquid. Outokumpu has an efficient agitator for this purpose. The GLS-agitator (GLS=gas, liquid and solid) is powerful for mixing oxygen, liquid and solid together. The current production in Pori plant is 40000 kg of silver, 5000 kg gold, 40000 kg of selenium and one hundred kilograms of platinum-palladium concentrate.

Jan 1, 2000