Search Documents

By B. K. Gorain

Mining of low grade deposits along with the necessity to design and operate flotation plants with high throughput presents unique metallurgical and environmental challenges that need to be addressed to reduce project risks, improve project economics and to sustain the profitability of operations over the life of a mine. Some of the key challenges include poor recovery of valuables and concentrate quality issues due to complex mineralogy, the need to use poor quality water such as brackish or sea water, reduce environmental impact from the process, integrate flotation with hydrometallurgy to maximize precious metals recovery, escalation of capital and operating costs, use of unproven technology and constant use of larger equipment, high ore variability, worldwide constraints on resource availability and an ever increasing need for reliable metallurgical input to financial models to evaluate economic viability of projects. The need to develop effective solutions to these problems in a short time frame is becoming a key to the success of any new project and for sustaining the profitability of a mining operation. An integrated multi-disciplinary approach to problem solving is crucial with the need for a more lateral thinking along with strategic partnerships and collaboration involving the right players. This paper presents some of the key findings based on experiences from a large number of challenging projects and operations focused on solving complex flotation problems Keywords: mineral processing, flotation, flotation problem solving, flotation optimization, plant design, innovation

Sep 1, 2012

By J. Lampke

The superior characteristics of iron ore pellets compared with natural ore and sinter are well known. Due to the higher grade and bulk density they show improved transport and material handling properties. While charging blast furnaces with pellets an increased productivity is realized through pellet?s uniform structure and composition. The increased productivity is caused by a high permeable furnace burden with a decreased coke usage via fuel injection and oxygen enrichment. Therefore, a narrow pellet size distribution and a minimum content -6.3 mm are necessary (Meyer, 1980). The required pellet size distribution can be achieved on the one hand by screening the fired pellets after the induration furnace and recycle the undersized pellets. On the other hand it is possible to produce high quality iron ore pellets with a high degree of sphericity, the important narrow grain size distribution ranging between 9 to 16 mm with high green strength directly in the pelletizing device. To produce high quality green pellets, possibilities and knowledge about adjustments of the pelletizing device are necessary. The paper presents a classification of state of the art pelletizing systems in accordance with the advantages of the pelletizing disc and pelletizing drum in issues like adjustability, green pellet quality, the recycling rate and the space requirement. By a systematization of the influences on pelletizing the common reliance of objectives on influence like pelletizing moisture, disc inclination, rotational speed, mass flow and rim height are given. A variety of industry-proven examples are shown, too. Keywords: Pellet, iron ore, pelletizing, pelletizing disc

Sep 1, 2012

By Mario Gerards

Maturing populations create an increase in the demand for the type of non-ferrous metals, which are used in the manufacturing of electronic products. The depletion of existing high-grade deposits, make it necessary to boost the efficiency of beneficiation processes and most importantly the yield (recovery rate of the value commodities). Increasing demand now makes it worthwhile to tap into resources, which were previously considered waste, for example secondary deposits such as tailing ponds and electronic waste. In order to achieve increased yields, increasingly finer, or even ultra-fine fractions have to be treated. In most cases, mineral characteristics such as size and density call for non-mechanical, high-capacity technologies to be used. There are various technologies that allow for the separation of fines and ultra-fines. This paper outlines the dynamics and efficiency of pneumatic flotation with emphasis on its application to the recovery of non-ferrous metals, from electronic waste. The conventional agitator flotation technology of an electronic waste processing plant was not able to recover ultra-fine non-ferrous metals satisfactorily, due to losses within the tailings. Because of its adaptability and its inherent suitability for non-ferrous metals, pneumatic flotation has been incorporated to the existing process achieving excellent results. The merit of the process lies in the state of the art technology, which does not utilize compressed air and any rotating parts, which results in a reduction in wear and energy requirement, both features of this innovative technology. In addition, the use of pneumatic flotation resulted in a significant reduction in residence time, when compared to mechanical flotation. Pneumatic technology is able to influence air bubble size in a flotation cell, by changing the speed and pressure of the slurry stream. Higher slurry velocities lead to the formation of smaller air bubbles, which is required for the successful flotation of ultra-fine particles. Conversely, decreasing the slurry velocity leads to bigger air bubbles. The optimum bubble size can be created according to different feed characteristics. This is important in case of feed fluctuations.

Sep 1, 2012

By Peter Ay, Vincenz Mehlstaubl, Satyanarayana Narra

"This study gives an insight into non-destructive testing methods suitable for porosity analysis at a small scale, firstly summarizing relevant state-of-the-art technology and pending patents, secondly realizing and documenting the start-up of the VHX-2000 digital microscope by the manufacturer Keyence and thirdly demonstrating practical application with the extended analysis of three fundamentally different agglomerates for which important application-related parameters are determined. Various analysis procedures on the different agglomerates the efficient and timesaving operational features of the digital microscope are outlined. Firstly an analysis of flax fibre agglomerates determines the process conditions best suited to produce agglomerates with specific properties by determining sphericity, cubicity, density and porosity as well as fibre damage and alteration. Secondly the production of iron-hydroxide - hemp-fibre agglomerates serves to obtain information on porosity values as a result of a cauterization of the fibres. The third analysis provides estimations of porosity values for acid-treated lignin agglomerates. Measurements were carried out with compact dry agglomerates and with soaked, expanded agglomerates, determining factors for total water carrying capacity. Practicability of non-destructive testing by digital microscopy is demonstrated and explained concerning the applications in this study by obtaining definite structural findings about the analysed agglomerates. Information on its operation is made available by a practice-oriented manual for the VHX-2000 digital microscope. Further suggestions for more in-detail analysis results with different instruments are given."

Jan 1, 2014

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By B. Z. Wu

The ore dressing of tin-polymetallic lean ores is a difficult problem and the research emphasis in domestic nonferrous metals mining field. Through research and tackle key problem,and in order to supply reference in dealing with the same types ores, this paper expatiates the exploiture and appli-cation of six item new technology and technics in ore dressing of tin-polymetallic lean ores. It include the technics of multi-step compounding disposing tailings, grinding step by step, grinding and processing circularly technology, high thickness without circle flotation technology, dispersedly flotation tin step by step technology, exceed fine lean plumbum stibium zinc flocculation flotation technology, the synthetically recovery of waste water after ore dressing technology.

Jan 1, 2014

By Caitlin Rogers

The environmental and economic sustainability of froth flotation is dependent on effective management, which in turn improves the performance of a concentrator. In economic terms this means improved recovery of valuable minerals, in environmental terms this means effective management of acid generating tailings. Three indicators were selected to measure the performance of an integrated flotation system. The system consists of two stages of flotation; valuable mineral flotation followed by environmental desulfurisation by froth flotation. The suitable indicators were selected based on their fulfilment of four attributes. An attribute is a desired aspect of an indicator. The four attributes were: comprehensive, relevant, sensitive and quantitative. Two environmental indicators and one economic indicator were selected. They represent revenue generation from valuable minerals and environmental cost of management. The suitability of the selected indicators was shown using illustrative scenarios.

Jan 1, 2014

By H. Kasaini

Batch wise adsorption tests for platinum (Pt) on the surface of activated carbon pellets (Norit RO 0.8 BET surface area 1100 mg/g) were carried out in mixed chloride solution. The purpose of this study was to assess and compare the adsorption performance of amine-treated activated carbons (AACs) and native activated carbons (NACs) in terms of adsorption capacity and selectivity. The effect of pH and temperature on adsorption capacity and selectivity was established. The amine- treated ACs were prepared by anchoring the amino groups (butyl amines) on the surface of AC pellets in aqueous media and the UV-Vis was used to determine the amount of amine sequestered from solution by ACs. The dosage of butyl amine on the surface of ACs averaged 0.15 g/g, carbon. The adsorption mechanism was described by the ionization and complexation model whereby interaction between the protonated AAC surface and the anionic chlorocomplex ions (PtCl5 [H2O]-, PtCl62-) proceeded by either electrostatic attraction or/and by covalent bonding [(NH3)2PtCl6 or (CH2COO)2PtCl6]. By comparison, the adsorption capacities of Pt on amine-treated ACs and native ACs were 53.8 mg/g and 33.03 mg/g, respectively which highlight the benefits of anchoring functional molecules on ACs. The selectivity of AACs was influenced by solution pH. Pt adsorbed selectively on the surface of amine-treated ACs at pH<1.5. The highest separation factor that was recoded pertained to Pt and Fe species (ßPt/Fe = 90) then followed by Pt and Ni species (ßPt/Ni = 30) or Pt and Cu species (ßPt/Cu = 15). The lowest separation factor was recorded for Pt and Cr ions (ßPt/N= 5). Adsorption kinetics of Pt on amine-treated AC surfaces, according to the first and second order reactions, were investigated and results showed that rates were in the order 10= 5). -4 min-1 and 102 g?min/mg, respectively. The pseudo 1st order kinetics predicted the adsorption capacity of 51.81 mg/g which was almost similar to the experimental value (53.8 mg/g) while the second order rate equation predicted Pt adsorption capacity of 40.1 mg/g. Both The Langmuir and Toth isotherm fitted the Pt adsorption at pH < 1.0. The Freundlich isotherm tended to underestimate the adsorption capacity of AACs.

Jan 1, 2014

By A. P. Das

Biomining technology focuses on achieving effective recovery of precious metals from their ores and concentrates using microbial techniques. Biomineral extraction of manganese from low-grade manganese ores using bioleaching was investigated in this paper. Five fungal strains were selected for screening of bioleaching of low-grade Mn ore collected from Sanindpur iron and manganese mines, Koira Sector, Keonjhar, Odisha, India. A fungal strain, Aspergillus niger was selected as it showed high efficiency of manganese leaching. Growth of the fungus was determined in terms of sbiomass dry weight and the final pH was monitored. The selected fungal strain was used for bioleaching of low-grade manganese ore of -150µm size particle size at 2 % pulp density with 2g/100ml sucrose concentration for duration of 20 days. About 60 % of Mn bioleaching was obtained with A. niger. The fungal species proved to be useful for manganese biomining.

Sep 1, 2012

By X. L. Song

A large amount of tailings in concentrators bring a series of problems to the environment and society. It is significant to reclaim the huge tailings and reuse them in industries in order to utilize mineral resources adequately. Primarily Lead-Zinc tailings with a certain quality of clay and feldspar were used to produce ceramic tiles by sintering method under specific technical conditions. By testing the properties of the ceramic tiles, it was shown that the amount of Lead-Zinc tailing used in the tiles was 60%~70%, and the mechanics properties were good. The optimum proportion parameters were Lead-Zinc tailing 60%, clay 35%, feldspar 5%, and the maximum flexural strength of tiles was up to 38.2MPa when it was sintered at 1090? for 30min. Its flexural strength, water absorption and thermal shock resistance reached the State Standard of GB/T4100.4. The product is suitable to be used in pavements and paths of parks.

Jan 1, 2014

By Klaus M. Hahn, Hermann Wotruba, Bernd G. Friedrich

"Due to an increasing demand for nickel and cobalt and the depletion of nickel sulphide deposits worldwide, the production of ferronickel from lateritic nickel ores becomes more significant. About 60 percent of nickel reserves are present in laterite deposits. Common production methods like acid leaching or smelting operations implicate high material and energy consumption. Physical processing methods are also not efficient, because of the fine microstructural intergrowth of the minerals carrying valuable elements such as nickel and cobalt. Due to the high energy consumption of metallurgical treatment of lateritic nickel ore (nickel grade: 0.8 - 3.0%, Co: 0.05 - 0.15%), the separation of waste material (about 75 - 85%) before the metallurgical treatment is desirable. Therefore, an alternative process has been developed, combining a pyro-metallurgical pre-treatment with selected mechanical processing methods. The developed process consisted of a selective pre-reduction and non-selective segregation of the contained metal phases in the first stage. By this, the properties of the metal carrying minerals were changed and could become subject to concentration by means of fine beneficiation processes afterwards. The parameters of the pre-reduction and segregation were varied and the pre-treated samples were examined concerning their efficiency of metalization grade and metal grain size. This paper describes the investigation of pre-treatment methods of a lateritic nickel ore. The pre-treatment and possible subsequent separation methods were examined with regard to the recovery of the valuable elements. Metalization grade was around 80% for both Ni and Co with metal phase grain sizes below 20 µm. Scanning electron microscopy revealed distribution of new metal phases not only on the reducing agent, but also on the “slag” material.INTRODUCTION Nickel laterites are characterized as strongly weathered regoliths with several zones containing reserves of nickel (Ni) and cobalt (Co). These laterites are formed on serpentinites and ultramafic rocks under climatic and/or tectonic conditions that have changed over time (Butt & Cluzel, 2013). The formation of Ni laterites is influenced by numerous geological and environmental factors. In general, there are three ore types named according to the dominant Ni hosting minerals: oxides, hydrous magnesia (Mg) silicates and clay silicates (Butt & Cluzel, 2013). The most Ni laterite deposits contain two of these ore types, usually an oxide zone and an either clay or Mg silicate zone. Distribution of these principal deposit types, their average Ni-bearing phases and mean Ni grade are shown in Table 1. A schematic profile of the different deposits based on the development on serpentized ultramafic rocks is given in Figure 1 (Butt & Cluzel, 2013)."

Jan 1, 2018

By V. Ross

"The Upper Group 2 (UG2) reef in the Bushveld Complex in South Africa hosts an estimated 40% of the world’s Platinum Group Metal (PGM) resources. The processing of this ore via flotation poses two particular challenges: limiting the levels of chromite in the concentrate to reduce downstream smelting problems, and enhancing the recovery of ultrafine (typically -10 micron), liberated PGMs. Conventional ways of suppressing the entrained chromite, such as froth washing, is not effective in PGM operations, which are dominated by mechanical cells. The recovery of fine particles is hampered by low collision efficiencies with air bubbles, as well as oxidised surface layers especially in tailings operations. This paper documents the results of laboratory tests on a run-of-mine PGM UG2 ore, investigating the application of a pneumo-mechanical column (PMC) and its effect on PGM flotation and its selectivity with regard to chromite. A key feature of the device is the stage-wise release of aerated slurry from an agitated downcomer, thus creating conditions where the superficial velocity profiles of air and slurry change axially within the separation zone. This aids segregation of the silicates and chromite-rich fractions in the separation zone, concentrating the latter towards the bottom of the column and minimising its entrainment into the concentrate. Comparison of the performance of the PMC to that of mechanical laboratory cells under equivalent operating conditions showed improved PGM flotation kinetics and recovery. This was accompanied by a decrease in gangue recovery compared to the mechanical cells by more than 40%, thus doubling the final rougher concentrate grade from 50 to 100 g/t. Significantly, whilst the overall Cr2O3 recovery was reduced by more than 60%, the selectivity (PGM recovery vs Cr2O3 grade in the concentrate) was doubled.INTRODUCTIONThe Bushveld complex in the northern part of South Africa hosts the world’s largest reserves of Platinum Group Metals (PGMs), representing approximately 40% of the total PGE. It is characterised by three main PGM bearing reefs, namely Merensky, Upper Group 2 (UG2) and the Platreef. The Merensky and Platreef are dominated by silicates in the form of pyroxenites, and carry economically recoverable amounts of copper and nickel, in the form of chalcopyrite and pentlandite. The UG2 on the other hand is a chromitite ore with chromite as (ideally, FeO.Cr2O3) the most abundant gangue, often constituting more than 70% by mass with a PGM grade of around 4.5 g/t. Other key gangue minerals are pyroxene, feldspar and talc. The PGEs occur in a wide variety of minerals, with platinum and palladium sulphides typically accounting for about half of the total. Base metal sulphides such as chalcopyrite, pentlandite and pyrrhotite occur in only very minor amounts, accounting mostly for less than 0.1% by mass."

Jan 1, 2018

By Ana Elisa Casas Botero

The Rhodococcus opacus microorganism was evaluated as a biocollector for flotation of barite. The electrophoretic behaviour of the mineral, before and after R. opacus interaction, was evaluated and showed that the cells adhesion shifted the mineral zeta potential curves. Adhesion tests were suggested a high affinity of the bacteria for barite. The experiments of the adsorption rate of the R. opacus on the mineral surface showed fast kinetics, achieving a maxim of cell adsorption after 5 minutes. Adsorption isotherm curves for barite could be categorized as Langmurian (L) type II. The best bioflotability results for barite achieved values around 75% for a R. opacus concentration of a R. opacus concentration of 250 ppm in the pH around 5.0. The studies were compared with the flotation of barite using a traditional collector. The bioflotation experiments were discussed considering the obtained adhesion tests. The results were supported by the Thermodynamic approach for selected pH values. The fundamental flotation studies showed the paramount potential that R. opacus presents as a biocollector and its possible application in the mineral flotation industry.

Jan 1, 2014

By P. Raghavan1

Reverse froth flotation experiments were carried out in the laboratory using two different types of kaolins for the separation and removal of coloring titanoferrous impurities from cryo-filtered clay after subjecting to high shear pre-treatment. This high shear pre-treatment consists of high shear agitation of a high solids clay slurry with the dispersant (high shear dispersion, HSD) followed by high shear agitation with the collector (high shear conditioning, HSC). After this pretreatment, the slurry is diluted and reverse flotation is carried out. One sample is from, Gujarat, India (Mamuara clay, ?MC?) while the 2nd sample is from Amberg, Germany (AKW clay, ?AC?). While MC consisted of 89% particles below 2µm and analyzed 1.06% of TiO2 and 0.29% Fe2O3 and measured a brightness of 83.4 %ISO, the corresponding values for AC are 67% below 2µm, 0.3% of TiO2? 0.49% Fe2O3 and 83.4 %ISO. The flotation performance is found to be greatly influenced by the conditions of high shear treatment. Important variables are HSD intensity (rpm), HSD time, HSC intensity (rpm), HSC time, HSD/HSC time ratio, ?HSD+HSC? total time etc. Higher shear intensities favor both the impurity liberation and collection. For both clays, it could be shown that impurity removal increases as total pretreatment time (?HSD +HSC? total time) increases up to a certain limit. For MC, the HSD time was only half or less than that of HSC time, while for AC, HSD time is at least twice (or more) than HSC time which is just an opposite manifestation. This is believed to be due to the striking differences between these two clays. Most importantly, the shear frequency is found more influential than the shear rate for the overall flotation performance for both clays. Interestingly, at high shear frequencies, i.e., when a stirrer with more number of teeth on the rotor is used, the ?HSD+HSC? total time is greatly reduced. Again, increased shear frequency helps to reduce flotation time and significantly improves flotation performance. At optimum conditions, product titania reduced to 0.35% for MC whereas the same reduced to 0.13% for AC. The product of flotation of MC measured 85%ISO brightness while that of AC measured84.6%ISO thus enhancing the value of the final product. It could also be established that the high shear pre-treatment shows better flotation performance than that due to collector dosage. Keywords: high shear dispersion, high shear conditioning, titanoferrous impurities, shear rate, shear frequency, brightness, clay recovery, Mamuara clay, AKW clay

Sep 1, 2012

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By B. Aydin, G. Erturk, G. Bulut

Coal is a complex material because of its structure consisting of carbon constituents and mineral matter. Flotation is readily carried out due to hydrophobic characteristic of coal. Therefore coal flotation is the most commonly used technique for fine coal beneficiation in order to acquire clean coal separating ash forming mineral matter from carbonaceous matter. In the coal flotation, floatability of coal both depends on characteristic of coal and used flotation reagent. Frothers as a flotation reagent are used to facilitate air dispersion into fine bubbles by prevention of bubble coalescence in the pulp phase, and stabilization of flotation froths. In this study, the effects of frother types and concentrations at different pH and particle size on the coal flotation were investigated. The representative sample was taken from Zonguldak, Turkey. It contains 9.1% ash and 7313 (kcal/kg) calorific value. Pine oil, Dowfroth 250, MIBC and Isooctanol were tested as frother types. It is determined that 1.92 ppm frother concentration is sufficient to float coal, except pine oil. In mixed frother tests, it is seen that Dowfroth 250 is more effective than others. No significant difference in coal recovery was observed for flotation tests at the different pH values. The best results are obtained in size of coal (-0.1 mm) with all frothers.

Jan 1, 2014

By D. Moradkhani

The heap leaching of oxide copper ores with copper cathode recovery by solvent extraction and electrowinning is now well established as a low-cost method of copper recovery. The main purpose of this study was to extract copper from the copper low-grade oxide ore of Chodarchaei mine using column leaching. The copper oxide ore contained 1.1% Cu and 1.75% Fe. The mineralogical analysis indicated the malachite (Cu2(OH)2CO3) was mainly composed of oxidized phases. The sulfuric acid leaching experiments were performed under the laboratory conditions. The influence of several parameters on the course of the reaction such as particle size, acid concentration, flow rate, and time was examined. The optimum collective extraction of copper and iron was obtained at a particle size of +10-15 mm for a leaching duration of 3 days with sulfuric acid concentration of 100 gpl and using a flow rate of 2.5 cc/min. Under these conditions, the recovery of copper and iron were 98.54% and 41.99%, respectively. Keywords: column leaching, copper, iron, working diagram.

Sep 1, 2012

By A. K. Mukherjee

In this apparatus closed sized particles are placed in a container and then fluidized by passing water through the load of particles. Water flow is adjusted to deposit particles in one or more layers depending on the specific gravity of each of the particles, after which the deposited particles are separated in portions of different specific gravity. The obtained portions represent different ore content of the closed sized fraction. The process is repeated for all other size fractions to generate washability curve of the feed. Three different types of iron ores and one coal sample are tested in this equipment. The theoretical yield-grade curve generated for iron ore feed is unique in absence of any such practice for ore minerals. Similar curve is generated for coal and it is compared with washability curve, an existing practice followed worldwide. This comparison validates the performance of the process and the equipment.

Sep 1, 2012

By M. Abdollahy

In this paper, the hydrophobicity of chalcopyrite particles produced with different laboratory mills has been studied; different grinding mechanism in themills made some changes in particles shape, Image Analysis (IA) method was used to determine the shape properties of chalcopyrite particles which are ground by a laboratory ball mill, rod mill and ceramic ball mill. The shape characters are stated in terms of shape factors such as circularity, convexity, roundness and regularity factor. Hallimond tube was used to float chalcopyrite particles followed by determination of critical surface tension of particles, this parameter used as a criterion to study the wetting behavior of chalcopyrite particles. The correlation between shape properties and critical surface tension of chalcopyrite particles showed that the hydrophobicity of chalcopyrite was affected by the shape. Investigations showed that the circular, round and more convex particles that produced with ceramic ball mill had lower hydrophobicity with higher critical surface tension (?c). The results also showed that the hydrophobicity of particles ground by ball and rod mills increased with the decrease of roundness, circularity, convexity and regularity factor of particles. Keywords: chalcopyrite, particle morphology, flotation, image analysis system, micro flotation method, hydrophobicity, shape properties

Sep 1, 2012

By M. Wierink

The lifecycle of a resource, specifically a metal, is often depicted as circle from primary production from mining to minerals processing and via manufacturing and use to disposal and recycling. When a material is recycled, it is considered as saved energy compared to producing the material from primary source. This is, however, a simplified representation. At each step of the life cycle, there are changes in the quality of the material due to different materials chemical and physical interaction, phase transformations due to diffusion, radiation etc. Due to these physical and chemical phenomena there are losses of material, which as determined by thermodynamics are not recoverable within the life cycle. This can be considered as an increase embodied energy per mass unit of substance and loss exergy from the material cycle. With low cyclic loss, the material will remain in the recycling loop for a long time, while with high cyclic loss it will disappear fast. Where you put the material determines how fast it disappears from the resource cycle. In this research paper the phenomena of quality degradation of material and idea of increase of embodied energy and exergy loss within a resource cycles is portrayed. The cyclic nature of material states and transitions and energy consequences of material quality degradation as well as the parameters affecting the length of the time scales of the material cycles are described. Currently the cyclic embedded energy and the history of material is not taken under consideration in generic life cycle assessment. This easily results into a conclusion that lifetime of product is optimized only in terms of how much energy an appliance uses during its lifetime, while ignoring the loss of embedded energy due to the effects caused by the environs the material is subjected to during the cycle. Better description of the time properties of material give us a possibility to design toward optimum lifetime of products in terms of resource efficiency. Keywords: product lifetime, material lifetime, recycling, cyclic resource efficiency, material state, material quality, exergy, embodied energy

Sep 1, 2012