Search Documents

By K. W. Stöckelhuber, A. Wenger, H. J. Schulze

"An important elementary step of the flotation process is the forming, drainage and rupture of a thin intervening liquid film between bubble and mineral particle.After the encounter of the bubble with the solid surface a wetting film is formed. The initial thinning of this film is driven by the capillary pressure inside the bubble. When the film has reached a certain thickness rupture can take place.There are two possible mechanisms describing this process:-, Growing fluctuation waves (spinodal dewetting) on fluid interfaces under the influence of any kind of attractive forces (electrostatic, van der Waals). -, Nucleation inside the film.Metastable wetting films on negatively charged, hydrophobic glass surfaces (gaseous phase methylated), or on hydrophilic, positively charged glass surfaces (with Al3+ ions), have been analysed by means of the kinetics of film thinning according to the Reynolds law. These experiments demonstrate that both mechanisms can be responsible for the rupture of a thin wetting film. In the case of hydrophobic surfaces the nucleation mechanism is preferred; in the case of opposite charged silica surface the capillary waves mechanism due to an attractive electrostatic double layer force between silica and air bubble takes place.Hereby the existence of a long range hydrophobic force. on a hydrophobic surface can be excluded. The apparent interaction can be explained by the presence of gas nuclei formed on heterogeneous surface sites. The results provide deeper insight into the mechanisms of wetting film stability, adhesion process in flotation and droplet coalescence."

Jan 1, 2003

By A. F. Usov

A potential of electric pulse disintegration in benification used for primary deposits ores containing precious metals is shown. Of special significance is that PGM and gold grains, being highly plastic, are easily liberated and are not smeared on the disintegrated rock fragments surface. It al-lows gravity separation, which is less expensive and more efficient, to be used instead of chemical processing, which is expensive and environmentally faulty.

Jan 1, 2014

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By Christopher Davey, Professor Emeritus, Marian Mazurkiewicz, Peter Kanjorski

The concept of a high pressure liquid jet mill with highly unsteady flow, has been developed and recently patented by Cornerstone Technologies LLC (CsT), for the purpose of micron and sub-micron particle production. The mill accepts feed sizes up to 15mm for some materials and is capable of sub-micron production. Successful material range from precious metals such as silver and palladium to dielectric components and substrates such as Barium Titanate slips, zirconia, titania and silica. The process has also succeeded in adequately reducing the size of materials for both composite and coating uses such as anthracite coal, graphite, chrome metal, wollastonite and more than 100 others. A unique design approach has been taken to highly maximize the energy flux in the mill’s chambers to create extremely high turbulence and destructive cavitation. This is assisted by shock waves, which cause particles to undergo ultra high frequency pressure pulsations, high frequency collisions and then abrasion, shattering, hydro-wedging, and cleaving. Due to these extreme properties the processing occurs in just fractions of a second allowing throughputs up to 1000 kg/h on a machine that would fit inside a 60 cm box. The technical solution and technological advance, as well as the environmental and economic benefits indicate rapid and wide spread acceptance of high-pressure liquid jet milling in modern industry.

Jan 1, 2003

By B. McFadzean, J. Taguta

The enthalpy of immersion is the heat change arising from the replacement of the solid-gas interface with the solid-liquid interface when a solid surface is immersed in a liquid. Although immersion calorimetry has been established as a valuable and reliable means of determining solid surface properties such as wettability, it has seldom been applied in mineral processing research. In this study, precision solution calorimetry was employed to measure the enthalpies of immersion of different minerals in water. The enthalpies of immersion were then related to the first-order flotation rate constant as determined by the microflotation technique. The same measurements were also made on sulphide minerals whose surfaces were modified to different degrees of hydrophobicity using different percentage coverages of amyl xanthate collector. The enthalpy of immersion technique was capable of distinguishing and ranking minerals according to their wettability. All mineral types and collector-treated minerals conformed to the same relationship that was found between the enthalpy of immersion and the flotation rate constant. This conformed, empirically, to a power law equation. As the enthalpy of immersion decreased, there were large increases in flotation response for very small changes in hydrophobicity. In addition, a critical enthalpy of immersion (CEI) was found, above which no flotation could occur. The scatter in the data points could be corrected for by adjusting the rate constant using the density of the minerals to produce a robust relationship between the rate constant and enthalpy of immersion. These results have shown that the enthalpy of immersion is able to indicate both the natural mineral hydrophobicity and the extent to which collectors can render a mineral hydrophobic. This technique has considerable potential to be used as a sensitive and accurate measure of mineral surface wettability in order to predict flotation performance.

Jan 1, 2018

By Bern Klein, Givemore Sakuhuni, Libin Tong

The use of continuous discharge centrifugal concentrators introduced in the early 1990’s for recovery of gold associated with sulphides has introduced a novel application niche for gravity concentration which could not be realized with the low mass yield batch and semi-continuous concentrators. A typical application is scavenging gold associated with sulphides from flotation tails which has potential to increase productivity by reducing gold loss to tailings and lower grinding cost by using a coarser grind. However, the full potential of this technology has not been fully exploited partly due to the lack of reliable small sample procedures to demonstrate applicability. This paper introduces a bench-scale procedure developed to characterize the Knelson Continuous Variable Discharge concentrator (CVD) for scavenging gold from flotation tails. The procedure code named gravity release analysis was derived from standard flotation release analysis. It is a modification of the gravity recoverable gold and gravity amenability test in order to best simulate continuous centrifugal concentration. Based on this iterative procedure, a gravity release index similar to the flotation rate constant, for measuring individual mineral gravity susceptibility for an ore is introduced which can be a useful quantitative measure to both predict application of centrifugal concentration and for plant design. The gravity release analysis procedure was tested on a polymetallic flotation plant tailing at Myra Falls, BC, Canada and results show that it can predict CVD performance. The gravity release index for gold was observed to decrease with each successive cleaner stage showing that the initial stages recover liberated gold whilst successive runs recover gold associated with sulphides and or gangue. The difference in magnitude of the gravity release index for different mineral species shows the species separable by centrifugal concentration.

Jan 1, 2014

By Paulo Castillo, Cesar Gomez, Jaime Alvarez

Operations using flotation to produce mineral concentrates require testing of frothers to characterize their ability to preserve bubble formation size and to build a stable froth. Many techniques have been proposed to measure parameters associated with these two roles. These techniques focus, in general, on only one of these roles and are based on special equipment operated at conditions quite different from those existing in industrial cells and columns. Both roles have been simultaneously characterized in a laboratory flotation column, but the requirements associated with the installation and operation of one of these units, are a serious limitation for its use on-site. A technique based on the use of a laboratory mechanical cell, a common piece of equipment in operations, will have wider application. Establishing the ability of a frother to control coalescence by preserving bubble formation size is done through bubble size measurements as a function of frother concentration. Froth build-up and stabilization is associated with the amount of water carried by bubbles into the froth layer, which has been demonstrated to correlate with the gas holdup in the collection zone. Procedures devised for determining the critical coalescence concentration (CCC) from measurements of bubble size as a function of frother concentration, and the gas holdup by collection of water displaced from the cell by the presence of bubbles at different frother concentrations, were tested. Three analytical-grade frothers were utilized: a straight-chain (1-heptanol) and a branched (MIBC) alcohol and a polyglycol (PPG425). The results obtained at a standard set of conditions, demonstrated consistent differences between these frothers, and the ranking from least to most effective for reducing bubble size or decreasing water drainage followed the same sequences found when more complex frother characterization techniques are used.

Jan 1, 2014

By A. Morrison, D. Mesa, P. R. Brito-Parada

"Froth flotation is the most widely used mineral separation technique. It is based on the relative hydrophobicity of valuable and gangue particles. In a flotation tank, two distinct zones can be identified: the pulp and the froth. The pulp is a turbulent region in which hydrophobic valuable particles attach to air bubbles while hydrophilic gangue particles remain in the slurry. As the particle-laden bubbles rise, a mineralised froth zone is formed that overflows as a concentrate. Although the process is more than a hundred years old, there remain many aspects that are not completely understood, particularly for the froth zone. Thus, the rules governing the design of flotation tanks tend to focus on pulp zone parameters, which are largely based on operating data. An example of this is the design and operation of impellers. These tend to be designed paying attention to hydrodynamic phenomena in the pulp zone, but their effect on the froth zone has not been completely addressed. The role of impellers in a flotation tank is to break the air bubbles in order to generate smaller ones and to provide an environment that enables the collision between those bubbles and the particles in the slurry. This usually creates turbulent regimes that can affect the pulp-froth interface, destabilising the lower regions of the froth and affecting the overall performance of the process. Different impeller designs and retrofit modifications have been proposed in the past, addressing some of those issues. However, there is no systematic study of the effect of different impeller designs on the bubble size in the pulp and its links to the stability of the froth. This work tested the impact of an impeller designs combined with the use of a stator on the performance of an 87 litres continuously operated laboratory-scale flotation tank, with a focus on bubble size in the pulp and froth stability. The results showed that the implementation of a stator system decreased bubble size and increased froth stability. That resulted in an increase of mass pull, measured as a proxy of metallurgical recovery."

Jan 1, 2018

By W. S. Eu

Reduction of weathered mineral ores can initiate phase transformation which can affect either their activation or deactivation, subsequently influencing the extent of extraction of desired metals in a leaching reagent. The reduction of ilmenite ores for one occurs as a series of parallel, solid state reactions which at present has no known mechanisms, although the evidence of their effects is abundant. Understanding these reactions may well be the key to uncovering the mechanism of ilmenite activation, hence enabling precise control of its reaction process to maximize yield of TiO2 extraction. However, documenting the solid state reactions in the reduction of ilmenite is challenging due to the ore complexity, the number of simultaneous reactions and the difficulty of capturing critical intermediate reactions and phase transformations during processing. The phase transformations of ilmenite minerals reduced at temperatures up to 850°C were investigated in this study. Mineral transformations were studied in-situ using synchrotron radiation based X-ray powder diffraction with temperature resolved tests. The effect of the extent of reduction and specific mineral transformations were verified by leaching reduced ore with sulphuric acid. The re-sults suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By Di Liu, Yongjun Peng

"It was identified that clay minerals adversely affect fine coal flotation through slime coatings. In the study, it was interesting to find that an anionic polymer dispersant, lignosulfonate, successfully mitigated the negative effect of clay minerals in coal flotation using fresh water, but in saline water, it exacerbated coal flotation.In order to understand the mechanisms underpinning the different behaviour of lignosulfonate in coal flotation using fresh and saline water, the adsorption isotherm, and dynamic light scattering (DLS) measurements were conducted in this study. While DLS monitored the molecular conformation change (swelling or shrinking) of the polymer in fresh and saline water, adsorption isotherms enabled polymer adsorbed amount on clay and coal mineral surfaces to be determined. It was found that lignosulfonate adsorbed on the coal and clay mineral surfaces providing effective electrostatic repulsions and resulting in a mitigation of clay minerals from coal surfaces in deionised water. In the presence of saline water, however, polymer molecular conformation changed. Polymer molecules were compressed and adsorbed in form of aggregates. The adsorption amount of lignosulfonate on clay minerals increased in saline water. A low dosage of lignosulfonate could not provide sufficient electrosteric repulsion to disperse clay minerals. Moreover, the high adsorption amount of the polymer on coal and clay surfaces led to a more hydrophilic coal surface, and coal flotation was therefore depressed in saline water. This study provides a new insight into understanding the role of anionic polymeric dispersants in mineral flotation using different quality water."

Jan 1, 2014

Calcium sulfate whiskers are considered to be a prosperous reinforced material in application due to their high mechanical properties. But the hydration occurs easily at moist atmosphere or in aqueous solution. The surface topographies of the calcium sulfate hemihydrate whiskers and the hydrates were analyzed by on-line observation and using XRD. The results indicated the transformation of the crystal type and shape of calcium sulfate hemihydrate whiskers and the reduction of whiskers? aspect ratio. The hydration process of the calcium sulfate hemihydrate whiskers and the effective parameters were further discussed based on FT-IR measurements. The conclusions were obtained that the hydration of calcium sulfate hemihydrate whiskers can be divided into the three phases, namely, initial hemihydration phase, dehydration phase, and coarsening, dissolving and the re-formation of calcium sulfate dehydrate crystal phase. In addition, it was found that in the hydration process of calcium sulfate hemihydrate whiskers the calcium sulfate dihydrate whiskers are formed at first and then converted into the calcium sulfate dihydrate with different crystal shapes, but in the hydration of gypsum hemihydrate the gypsum dihydrate is formed without transition products. The surface active site-calcium ion which has strong trend to react with H2O, the surface ?OH and the inner channels are considered to play important roles in the hydration process of calcium sulfate hemihydrate whiskers.

Jan 1, 2014

By J. R. Cui

The production of electric and electronic equipment (EEE) is one of the fastest growing areas. This development has resulted in an increase of waste electric and electronic equipment (WEEE). In view of the environmental problems involved in the management of WEEE, many counties and organizations have drafted national legislation to improve the reuse, recycling and other forms of recovery of such wastes so as to reduce disposal. Recycling of WEEE is an important subject not only from the point of waste treatment but also from the recovery of valuable materials. Consumer electronic equipment (brown goods), such as television sets (TV), radio sets, and video recorders, are most common. However, recent work on recycling of waste electric and electronic equipment (WEEE) primarily focused on personal computer and printed circuit boards scraps. Based on a detailed characterization study of consumer electronic scraps, recycling of TV scraps oriented to recovery of metals is highlighted by utilizing air table separation, eddy current separation, and optical (metal) sorting process. The result indicates that a high recovery of copper could be obtained by utilizing an effective gravity separation process. The separation results reveal that air table separation is an effective technology to recover metals from consumer electronic scraps. By using a DGS table, approximately 90% of non-ferrous metals were recovered in the heavy product with a purity of 40%. Printed circuit boards and cables in TV scrap cause metals loss due to the fact that metals in printed circuit boards and cables are not liberated from plastics and ceramic materials. The study shows that eddy current separation and optical (metal) sorting process provide alternatives for recovery of metals from shredded TV scraps.

Jan 1, 2014

By A. Buchanan, M. Mirnezami, A. L. Restrepo, J. A. Finch, M. S. Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally revealed two aggregation maxima at pH 8-10 and 10-12. From measurements on sphalerite and silica suspensions the double maxima were replicated by Zn ions (pH 8-10) and Mg ions (pH 10-12) corresponding to the presence of zinc hydroxide and magnesium hydroxide, respectively. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By C. Tokoro

Co-precipitation of dilute toxic anions with ferrihydrite is an important removal mechanism in wastewater treatment system. Although, numerous qualitative studies have been published on removal characteristic from wastewater of dilute anions by co-precipitation treatment, detail mechanism or quantitative characteristic is not well understood. This paper discussed the co-precipitation mechanism of As(V) and Cr(VI) with ferrihydrite by comparative experiments between co-precipitation and simple adsorption. In this study, co-precipitation experiments and simple adsorption ones were distinguished closely. In the former, precipitation of hydroxides and adsorption of anions develop simultaneously, but in the latter, anions adsorb onto prepared hydroxides. Although high affinity anions for hydroxides (e.g. As(V) for ferrihydrite) showed quantitative difference of removal ratio between co-precipitation experiments and simple adsorption ones, low affinity anions (e.g. Cr(VI) for ferrihydrite) showed quantitative agreement in spite of deferent forms of ferrihydrites between them, that is, amorphous ferrihydrite was formed in co-precipitation experiments, but goethite was formed in simple adsorption ones. In order to discuss the mechanism of co-precipitation phenomena, three experimental studies have been carried out: (i) adsorption isotherm measurement in the co-precipitation experiments of As(V) or Cr(VI) with ferrihydrite, (ii) zeta potential measurement of co-precipitated or simple ad-sorbed ferrihydrite with As(V) or Cr(VI), and (iii) XRD analysis of co-precipitated As(V) for ferrihydrite. All experimental results suggested the main mechanism in co-precipitation phenomena of As(V) was not only a surface complexation (simple adsorption) but also a surface precipitation.

Jan 1, 2014

By Marco Le Roux, Martha Van Rensburg, Quentin Campbell

Fluidised bed drying is currently receiving much attention as a dewatering option during the beneficiation of fine (defined here as between 1 mm and 2 mm particles) coal. Apart from concerns about safety and combustion, the operating costs can be high if very high gas or air temperatures are used. The aim of this study was to investigate the removal of moisture from fine coal by using air at a lower temperature (25 - 55°C) within a controlled environment by lowering of the relative humidity of the air. It was firstly proven that fluidization has a major advantage over non-fluidized beds, with regards to drying rate and final moisture content. Hereafter several parameters that influence the dewatering rate and final moisture content were tested, from which it was concluded that the relative humidity of air acts as the largest driving force for dewatering. Parameters tested included relative humidity, temperature and coal composition. Energy balances showed a positive nett energy increase in the dried coal during combustion when related to the energy input during drying. In comparison with thermal drying technologies, fluidized bed drying was proven to be less energy intensive. It was therefore shown that this is a viable technology for the dewatering of fine coal.

Jan 1, 2014

By G. H. Li

Preparation strontium carbonate with celestite concentrate by flotation is studied by agglomeration-reduction roasting process. It is shown that, the drop strength of green pellet is greater than 4 times?(0.5m) -1 under the balling conditions of moisture of 9% and time of 18~20min. Lignin xanthate obviously improves the ballability of the celestite concentrate due to the increase of surface hydrophilicity, therefore, the balling rate is increased, as well as green ball strength. The drop strength of 7 times?(0.5m) -1 can be obtained when the lignin xanthate dosage is 0.5%~1%. Reduction roasting with anthracite shows that the SrSO4 conversion is 82%~83% for celestite concentrate pellet, under the optimal conditions of roasting temperature of 1100~1150? and time of 30min, and it is 10% higher than conversion of celestite lump under the same conditions. The strontium carbonate are prepared after roasted pellets are leached, purified and carbonated, and the SrCO3 content is higher than 97% , while the content of CaCO3 is less than 0.3%.

Jan 1, 2014

By Chao Li, Kym Runge, Saeed Farrokhpay, Dee Bradshaw

"It is well known that froth phase has a controlling influence on the overall flotation performance. Froth recovery is expected to be affected by froth transportation behaviour. The latter has been represented by different volume balance and energy balance based models. In froth transportation models based on a volume balance, the froth phase is divided into different zones. The total froth residence time is the sum of the time spent in each zone and is dependent on the cell geometry, bubble burst rate and the position that bubbles enter into the froth phase. Alternatively, the froth transportation model based on an energy balance treats the froth phase as a block. In this model, froth height above the concentrate lip is being predicted by minimising the energy of the system which is dependent on the froth geometry, froth stability and froth rheology. The froth height can be used to calculate the froth efficiency of delivering mineralized bubbles from the pulp to the concentrate lip. This paper critically analyses the current models of froth transportation in flotation, and examines the limitations of these models. The importance of froth rheology, which is the resistance to the froth flow towards the discharging weir, in determining froth transportation, is also highlighted."

Jan 1, 2014

By Michel Brissette, Shaheer Sanuri, Veroljub Mihajlovic

"The main purpose of geometallurgy is to improve the mine planning by mapping hardness and throughput into the mine block model using geostatistics to eliminate the large production fluctuations caused by the ore hardness variability coming from different parts of the pit. However, not all grinding testwork available commercially can be applied to geometallurgy because of large amount of sample required and the associated cost per test. Geometallurgy is now being used in designing grinding mill but as the mining project progress, the accuracy of engineering must improve from 30-35% during the scoping study to 10-15% at the bankable feasibility stage and less than 5% for Engineering Procurement and Construction Management. For SAG milling, the SAG Variability Test (SVT) is an abbreviated version of the standard SAGDesign test developed for this geometallurgical need. The same amount of ore than the original test is ground for three cycles into an open batch SAG test and then the SAG pinion energy is predicted to the standard end point of 80% passing 1.7 mm. For ball milling, a Bond Variability Test (BVT) was also developed using the SAG ground ore from the SVT. The Bond ball mill grindability (Gpb), corresponding to the average of the net grams per revolution from the last three cycles of the Bond test, is also predicted from the third cycle. The relative error for both the predicted SAG ore hardness (WSVT) and Bond Work Index on SAG Variability ground ore (Sv-BVI), in kWh/t, averaged 5.5% and 3.8% respectively compared to the SAGDesign testwork values and are within 7% and 10% respectively from plant benchmark and within 7% from the samples sent to all partner laboratories. Both tests can be continued to measure the true hardness necessary for mill sizing. This article discusses the development of these two new tests, SVT and BVT, their potential use and accuracies in any geometallurgical program."

Jan 1, 2014

By Bern Klein, Givemore Sakuhuni

Flotation is the dominant base metal extraction technique and it requires ore to be ground below the liberation size for effective recovery due to its dependence on mineral surface properties. For a poly-metallic ore, differential hardness of constituent minerals leads to over grinding of softer minerals before the harder minerals are fully liberated, which makes selection of a target grind size complex, and the complexity increases when treating leaner ores. Flotation recovery deteriorates above 100 and below 10 microns causing significant loses of valuable minerals in most flotation circuits. Although enhanced gravity concentration is known to be effective at recovering particles above 100 microns, which are difficult to hydro-dynamically transport, exploiting differential specific gravity for base metal separation was not an option in the past. This was partly due to the absence of high mass yield gravity techniques. The advent of continuous gravity concentrators with flexible mass yields, in the past two decades, has necessitated investigation of possible base metal applications. The Knelson CVD, one of the continuous discharge centrifugal concentrators, has an established application niche for sulphides associated with gold. However, its base metal applications have never been rigorously tested. Considering the dependence of flotation recovery on particle size, continuous discharge centrifugal concentration can be integrated in flotation circuits to capture flotation non-recoverable coarse particles. This paper explores how particle size, liberation and mineral hardness influence application of continuous centrifugal technology to regulate galena deportment in a polymetallic base metal plant. The results show that particle size affects galena recovery more than liberation. In view of these results, the CVD can be integrated in the primary grinding circuit to pre-concentrate the heavy sulphides at a coarser grind size with potential grinding energy savings.

Jan 1, 2014

By Slobodan B. Vujic

"Some twenty years ago, during construction of flotation in the “Veliki Krivelj” copper and non-metallic mine Bor, a computer supported system for remote controle of technological process was installed. Nowadays, the major part of equipment of this system is worn-out and technically old-fashioned. Having this in mind a decision was made to design a new computer supported information-management system for Flotation. The paper presents a concept and features of project solutions.For the requirements of remote monitoring and management of technological process in Flotation of “Veliki Krivelj”, Copper and non-metallic minerals mine in Bor, Yugoslavia (hereinafter: CNM Bor), a measuring-regulation equipment was implemented and a computer control system, adjusted for that time, built some twenty years ago. The major part of this equipment is today worn out and technically out of date.Having estimated that production and business activities could hardly be more efficient, operative and successful on one hand, and available mineral and other resources rationally exploited, the CNM Bor made a decision in 1999 to improve information-management function of Flotation. The idea was that the set task be realized through development and introduction into practice up-to-date integrated and computer-supported production-business information-management system. The first logic step in completion of this task refers to engineering-creative determination of information management system (hereinafter: IMS), namely to project elaboration.When considering the real system from technical, technological, organization, monitoring-management, logistic and business aspects, the Project on IMS of Flotation, should provide a rational, modern and, for the real system conditions, complete solution. The Project solutions should be based on the most recent knowledge from computer and measuring-regulation technics as well as from CIM concept (Computer Integrated Manufacturing)."

Jan 1, 2003