Search Documents

By Michel Bustamante

The Arbre viaduct, 200 metres long, is the most important structure on the Belgian portion of the High Speed Train line between Paris and Brussels. The particular geotechnical conditions of the soil with carboniferous limestone affected by karstic phenomena, has prompted the designer to found the viaduct on systems of high capacity vertical and batter micropiles. The design of the working micropiles was validated by full scale tests performed on instrumented micropiles. The size of the structure and the deformation criteria to be met when HS trains are crossing the viaduct, together with the lack of references for such innovative structure, called for monitoring the movements of the piers as soon as the link was open to traffic. The authors report on the results of loading tests on micropiles and the results of settlement structure monitoring for a period of 4 years. Settlement of the foundation is estimated taking into account the group effect.

Jan 1, 2002

By Ronnie X. Gu, Xing Zheng, Gem-Yeu Ma

Due to implementation of the rotator construction method from which a smooth shaft was anticipated, a full-scale pile load test (Osterberg Method) was performed at Pier 14 Pile 9 of the main span of the New Benicia-Martinez Bridge to confirm the design parameters of the rock sockets. Two levels of load cells were fabricated in the reinforced cage of the rock socket. Each level consisted of three 670-mm Osterberg load cells with a total testing capacity of more than 50 MN in both directions. In an attempt to separate side friction and end beari ng, a 75 mm thick compressible Styrofoam material was placed at the bottom of the cage. The pile load test was carried out in four stages. The multi-level multi stage pile load test data was interpreted for casing friction, side friction for two rock strata, end bearing, and residual side shear values under repeated loading in opposite directions. The side friction from the casing in soils at Stage 2 is approximately 9 MN. The end bearing at the tip of the rock socket at Stage 3 was calculated to be approximately 17 MN at a displacement of about 75 mm. The residual side shear resistance for the 10 m 50% RQD rock strata was calculated to be 9 MN or approximately 50% of initial values, after being pushed 0.3 mm upward in Stage 1, 71 mm downward in Stage 2, then 55.5 mm upward again in Stage 3, and finally 105.3 mm downward in Stage 4. The test results surprising ly indicate that the side shear resistances from both low RQD intensely weathered rock and higher RQD slightly weathered competent rock are about the same at approximately 19 MN. This pile load test provides very critical information for confirming deep shaft design and analyses.

Jan 1, 2005

By James N. Mure

The paper describes the design development and construction of bored piles at Pindersfield Hospital, Wakefield, U.K. The piles were of monopile type. Monopile is the term used to describe piles which are constructed without pile caps so that the superstructure columns bear directly on the pile top. Pile geotechnical design was developed from the Site Investigation data and testing of two preliminary piles. Final design philosophy is described. Pile structural design was developed from the loadings applied by the superstructure, and the requirements, tolerances and limitations of monopile construction techniques. Construction was closely controlled in order to achieve a ?right first time? result. The conclusion gives a critique of the system and its value.

Jan 1, 2008

By Ahmad Mahboubi

The damage caused by catastrophic earthquakes has always been an incentive towards more sophisticated building codes and requirements. In parallel to computer technology development, the engineers? attitude towards acquisition of more accurate results is increasing. This approach leads to designation of structural elements with more elaboration considering different aspects of their behavior. In addition, less simplified methods will be considered as satisfactory for analyzing such problems. The problem of soil-pile-structure interaction is one of the phenomena that can be included in this category. In general, there are two methods by which the study of soil-pile interaction phenomenon is studied. These include direct and sub-structuring methods. The sub-structuring approach relies on the linear or slightly non-linear behavior of soil since it employs the results of kinematic interaction analyses for inertial interaction studies. In the past, the kinematic interaction between pile-soil was considered as negligible. This was due to the softer nature of the surrounding soil that increased the time period of vibrations. However, more research revealed that although this approach was consistent in many cases, there were some sites where the time period decreased. This was due to the material properties of the foundation and the soil, in a way that caused the frequency of vibration meet natural frequency of the system. The second type of interaction is the inertial interaction which reflects the effect a structure on top exerts on the oscillation experienced by the foundation. This paper examines the impact of vertical load on the inertial interaction by virtue of impedance functions. Three different load cases for the structure at the top of a pile foundation were considered for the analyses conducted in this study. The changes in the stiffness and damping of the system by frequency are studied and finally, the results are presented.

Jan 1, 2010

By Beim Jorge, Piscsalko George

"Verifying the quality of cast-in-place foundation applications, particularly those cast under slurry, is of course important, due to its great dependency on the methodology employed and on the practices of the site personnel. Due to the techniques used to install these elements, it is usually not possible to inspect the hole prior to grout or concrete placement, but there are several Non Destructive Test (NDT) methods available to assess the integrity of the completed foundation elements. This paper will compare several NDT methods with the Thermal Integrity Profiling (TIP) method for verifying the integrity in Continuous Flight Auger (CFA) piles and Bored Piles. The Thermal Integrity Profiling method will be described and some examples will be presented where TIP testing was used to confirm the structural integrity of CFA piles and Bored Piles.IntroductionThere are several Non Destructive Test (NDT) methods available for integrity testing of foundation elements. Each of those methods has advantages and disadvantages (White et al, 2008). Some methods test the integrity based on the reflections of a stress-wave generated by low or high-strain impact, while others require tubes to be installed prior to concrete pouring, and test the integrity between those tubes, or within a small proximity of them. The former methods (especially the low-strain) are faster and more cost-effective, but are not able to detect the quadrant where the damage is located. The latter methods are able to determine the quadrant, but do not test the region outside of the reinforcing cage, that is, they are not able to determine the concrete cover. The Thermal Integrity Profiling (TIP) NDT method overcomes the limitations of these other NDT methods.Overview of Shaft Integrity MethodsUntil now, the most widely used methods to test the integrity of Bored and CFA piles were the low-strain pile integrity testing and the cross-hole ultra-sonic testing. The low-strain method for integrity testing (PIT) involves attaching an accelerometer usually to the pile top (using a putty or wax) and striking the pile surface with a handheld hammer, which causes a compressive wave to enter the pile. This wave is totally reflected when it reaches the end of the pile or a major defect, and is partially reflected when it encounters any change in crosssection, or a change in the resistance or density of the pile material. These reflections arrive at the top at a time determined by the distance and wave speed, and causes a noticeable change in the signal detected by the accelerometer. The acceleration signal is normally converted to velocity by simple integration, and sometimes the force applied by the hammer is also measured. The velocity (and force) signals can be processed by the pulse-echo method (in the time domain) or by the transient response method (in the frequency domain)."

Jan 1, 2015

By Theodore von Rosenvinge

Large diameter (2.4 meter) drilled shaft foundations were installed to depths of over 62 meters through soil into Arkose bedrock for Connecticut?s Pearl Harbor Memorial Bridge (I-95 over New Haven Harbor). The project involved many ?firsts? including the first ?extradosed? cable-stayed bridge in the US, and for Connecticut, the deepest drilled shafts, the first use of a rotator to install shaft casing, and the first use of the Mini-Sid technology for rock socket bottom inspection. Design utilized both friction and end bearing for rock sockets. O-Cell testing was employed to maximize performance factors during design and to allow adjustments to socket lengths during construction. Favorable test results permitted a reduction in socket lengths and significant cost saving.

Jan 1, 2011

By John P. Turner, Steven S. Dapp, Dan A. Brown

"The Goethals Bridge Replacement (GBR) spanning the Arthur Kill Waterway between Elizabeth, NJ and Staten Island, NY is supported on over 200 drilled shaft foundations ranging in diameter from 4.5 ft to 10 ft and socketed into Passaic Formation siltstone. Four drilled shafts, two on each side of the bridge (NJ and NY), were load tested using the bi-directional axial load method. Axial test results demonstrate that RQD, taken by itself, is not necessarily a reliable indicator of side or base resistance. High recovery with low RQD can be a function of horizontally bedded siltstone and shale where the individual pieces of core do not exceed four inches, but may still provide very high side and base resistance. Axial testing was followed by a lateral rapid-load test (Statnamic) on each of the same four shafts. In addition, one of the shafts was subjected to a static lateral load test to validate the rapid-load method as being representative of static loading conditions. Results of the axial load tests provide the basis of unit side and unit base resistances used in the LRFD design of the rock sockets for axial loading, while results of the static and Statnamic lateral load tests were used to calibrate p-y curve parameters used for design under lateral and moment loading. This paper describes implementation of the load testing program and its role in the design process.INTRODUCTIONDesign of drilled shaft foundations for the Goethals Bridge Replacement (GBR) required load testing in order to validate the parameters used for calculating geotechnical axial and lateral resistances. The bridge, including foundations, was designed in accordance with the AASHTO LRFD design specifications, 6th Edition (2012). The bridge owner is the Port Authority of New York and New Jersey (PANYNJ). One of the PANYNJ project requirements was stated as follows:“Perform a minimum of two (2) separate axial compression load tests (one [1] in New York and one [1] in New Jersey) for each demonstration shaft of different size and construction methodology to verify the design assumptions and construction procedures. At a minimum, one (1) demonstration shaft is required to be representative of production shafts with a diameter within one (1) foot above or below the demonstration shaft diameter.Conduct a minimum of two (2) lateral load tests (one [1] in New York and one [1] in New Jersey) for each demonstration shaft of different size and construction methodology. At a minimum, one (1) demonstration shaft is required to be representative of production shafts with a diameter within one (1) foot above or below the demonstration shaft diameter.”"

Jan 1, 2016

By T. G. Davies

The paper presents design equations for singly laterally loaded piles embedded in sand. These equations were obtained from a comprehensive nonlinear analysis of free and fixed head piles subjected to horizontal loads. The sand is modelled as an elastic-perfectly plastic material whose strength and stiffness are proportional to depth below ground level. The soil's response is described by means of a boundary element representation of the continuum while the pile itself is created as an elastic beam. Equations for the latter are derived directly from the Bernoulli-Euler theory and are coupled with those describing the non-linear soil response. The effects of bearing failure along the front, face of the pile, shear failure along its sides and tension failure at the back face are accounted for in the analysis. Simple equations are presented to describe both the elastic and inelastic responses. The only sol parameters required to use these equations are the angle of internal friction of the sand and a parameter characterizing the rate of increase of the sand's modulus with depth. The latter can be taken as equivalent to the modulus of subgrade reaction. The results of this analysis show that soil yielding is very significant at working load levels, resulting in substantial increase in bending moments and lateral deflection.

Jan 1, 2010

By Vivek Samu, Murthy Guddati

A new method called Effective Dispersion Analysis of Reflections (EDAR) was recently developed to effectively analyze the dispersive waves generated from lateral impact to piles. This paper presents the results of nondestructive length estimation of existing piles through EDAR. EDAR provides a new visualization method for analyzing wave reflections by transforming the response into the frequency domain thus eliminating the need to perform difficult peak picking in the time domain. In addition to being able to analyze dispersive waves, EDAR also incorporates the effects of radiation damping due to the surrounding soil leading to more accurate length estimates. Concrete filled steel tubes of different embedment depths were tested both in laboratory and field conditions. Length estimates obtained were within 10% error margins after careful analysis accounting for the presence of soil effects and effects from pile top reflection.

By Ke Yang

"Drilled shafts are typically used to support structures subjected to large moments at the shaft head. The large moment can produce push and pull forces on the two sides of a drilled shaft. Consequently, the applied moment is partially resisted by the push-pull moment resistance induced from the vertical side shears. This type of push-pull resistance has not been fully recognized in most design and analysis methods. In this paper, a 30 finite element model for a drilled shaft subjected to lateral load and moment is presented and is validated against two field lateral load tests. Based on the 30 finite element model, a parametric study is carried out. It shows that the push-pull moment can resist 18-35% of the applied moment. The parametric study also shows that the push-pull resistance varies linearly with loading eccentricity when the eccentricity is less than the shaft embedment length. A method to estimate the push-pull resistance is proposed based on the results of the parametric study. Then, a new method for lateral capacity prediction is proposed to account for the push-pull resistance. The base shear resistance is significant for short drilled shafts; therefore it is also included in the proposed method. A case study on four lateral load field tests illustrates that the new method could improve the accuracy of lateral capacity prediction when compared with the traditional Broms method.INTRODUCTIONDrilled shafts are typically used to support a variety of structures subjected to large moments. Sound walls, highway signs, traffic signals, high-rise buildings, electrical transmission towers, and bridge piers are examples of cases where lateral loads with large eccentricity would result in high overturning moments on foundations.Current analysis methods for capacity predictions (Broms, 1964a and 1964b; Brinch Hansen, 1961) or deflection predictions (Reese, et al. 197 4) of laterally loaded drilled shafts are based on the lateral resistance of soils and rocks. However, O'Neill pointed out that moments can be partially resisted through the push-pull resistance provided by the vertical side shears due to the rotation of the pile (Reese, 1997)."

Jan 1, 2005

By Paolo Cavalcoli, Federico Pagliacci

"As opposed to the static functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles). Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago. These are real challenges for those carrying out these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the rhetorical figure of ""David and Goliath"": cunning versus force. In reference to the case studies in this article: the permanent retaining walls for the Copenhagen Metro, and the structural repairs to the Arapuni Dam in New Zealand and the Wolf Creek Dam in the U.S., we will describe the foundations constructed in presence of rock using combined small-diameter direction drilling solutions, associated with their enlargement up to the project’s size, at depths exceeding 300 feet. Finally, a case study will be presented on the implementation of a large cross-section of an excavation in the rock, at depths greater than 800 feet.IntroductionAs opposed to the functional recovery of existing structures, the construction of infrastructures in an urban environment, when combined with complex geological situations, often involves building foundation structures, whether circular or rectangular in section, through rock formations or chaotic strata (sand and gravel with cobbles).Until a few years ago, these formations or strata were sometimes an insurmountable constraint on traditional foundation installation techniques. The difficulty in overcoming these geological situations is sometimes added to the increasingly frequent need to reach depths that were unimaginable just a decade ago.These are real challenges for those building these works and for those manufacturing the necessary equipment. There are two main methodological approaches to these problems, that can be summed up in the biblical figures of ""David and Goliath"": cunning versus force. In the engineering field, the force is summarized in the use of ever-larger drilling equipment in terms of installed power, weight in working conditions, winch and rotary capacity."

Jan 1, 2015

By Edward Jacobsen

The Oak Creek Power Plant in Oak Creek, Wisconsin is currently undertaking an expansion project. In order to supply cooling water to this facility, a 27' (8.2m) diameter tunnel will be bored, in rock; to connect to 4 vertical Intake shafts located approximately 1.5 miles (2.4km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to Install these intake shafts. When complete, the plant is expected to circulate upward of 2 billion gallons per day (7.5 billion liters) through this system. Two shafts were drilled in a (shortened) construction season in 2005 and the remaining 2 shafts and 4 liner assemblies were completed in 2006. Future connection to the tunnel, in 2007, will be accomplished by mining upward to reach the lower portion of each liner and then removing its internal bulkheads to permit the flow of the lake water into the tunnel.

May 11, 2007

By Yu Chuang, Zai Jinmin, Liu Songyu

"The piled raft foundation is a geotechnical composite construction method, consisting of three elements, piles, raft and soils, which is applied for the foundation in an increasing number. Differential settlements have numerous negative effects on a superstructure in piled raft foundations. Through the analysis of the production mechanism of differential settlements and differential settlements control measures, a method of adjusting pile configurations is presented to control differential settlements. By comparing the measured data and finite element method analysis of one oil storage piled raft foundation, the new method is verified that the differential settlements can be reduced effectively and the inner forces of foundations are more reasonable with varying length pile configurations. The differential settlements can be minimized or even reduced to zero with right pile length.INTRODUCTIONPiled raft foundations are widely adopted for the prominent advantage of limited settlements and adequate bearing capacities. However, there always exits differential settlements in conventional piled raft foundations. The differential settlement is the main cause that produces additional stresses in the structure. Differential settlements have numerous negative effects on a superstructure as well as on a foundation, and should be restricted to allowable limits. How to control the differential settlement is the key interest.An increasing number of structures are founded on piled rafts. For this reason, design strategies that enable an optimized design have a major importance for safety and economy. An optimized design may be defined as a design achieving maximum economy of the solution, that is minimum cost for the installation of the foundation."

Jan 1, 2005

By Evangelia Ieronymaki

Civil engineering education relies on traditional methods of teaching, comprising mostly of deductive instruction by presenting the theory, followed by applications. This paper presents an alternative way for teaching foundation design to senior students, introducing a more inductive approach. The students are presented with a project/game adapted to a real-world problem at the beginning of the course. They are asked to identify the correct steps and methods throughout the lectures, for reaching an appropriate solution that they document and present at the end of the course. To make the project more enjoyable, the project has the format of a game where the students compete with each other on completing the task faster and more efficiently. The goal of this teaching approach is to enhance the ability of the students for problem solving and the engineering way of thinking, while playing a game. In the end, the students were requested to respond to a survey regarding the efficiency of this project/game on their learning. The results showed that students prefer more inductive methods for a design course, feeling that this project made them think more like engineers, while the ‘game’ twist of it made the whole course more fun. INTRODUCTION Most civil engineering courses are taught in 2019 the same way they used to be taught 40 years ago in the 80s. Classic methods are mostly deductive, where the instructor presents the theory first and then applications of that theory follow. Little or no attention is given initially to why the theory was developed or what are the problems it solves. The applications of the theory, and thus the purpose it serves, come only in the end and after methodologies have been presented, leading the students to show low interest in the material. As Albanese and Mitchell (1993) have reported, people are mostly motivated to learn things when they clearly see the need to know them. This explains the students’ little motivation that, if any, comes mainly from the fact that the material may be useful either in other courses or in their future careers. On the other hand, there are alternative inductive methods of teaching, where the role of the students is more active. A lot of researchers have highlighted the benefits of inductive methods in teaching engineering courses. Based on Prince and Fedler (2006), inductive methods include; a) inquiry-learning, b) discovery learning, c) problem and project-based learning (PBL), d) case-based teaching, and e) just-in-time learning. Inquiry-learning is maybe the most traditional method of inductive teaching/learning methods, where the instructor asks questions or poses problems and the students need to apply the theory they have learnt in order to find the solution (Bateman 1990; Prince 2004; Lee 2012). Similar to inquire-learning is the discovery learning, where students have to find the solution to a problem or answer to a question, while the instructor simply provides feedback to the students without guiding their efforts (Leonard 1988; Westbrook and Rogers 1994).

Jan 1, 2019

By James G. Ulinski, Sebastian Lobo-Guerrero, Vishal B. Patel

"Recently modified design equations used in the transportation industry to calculate side friction and end bearing capacity for drilled shafts are now providing more realistic estimations of capacities than did previous methods. Using multiple case studies and test results from various projects, a more realistic design approach was formulated by the Federal Highway Administration (FHWA), which resulted in greater values of ultimate capacity for side friction and end bearing and in a more efficient design overall.In 2010, the FHWA published GEC-10 – Drilled Shafts: Construction Procedures and LRFD Design Methods, which illustrates a different method of calculating side friction and end bearing resistance and results in greater values for design. In 2014, the Association of State Highway and Transportation Officials (AASHTO) adopted the method put forth by FHWA, which was included in its LRFD Bridge Design th Specifications, 7 Edition. The Pennsylvania Department of Transportation (PennDOT) recently adopted and incorporated the similar methodology as AASHTO for calculating side friction and end bearing for drilled shafts in rock, and these changes are reflected in the 2015 edition of the PennDOT Design Manual, Part 4 (DM-4). This article discusses the past and current design methodology along with a project case study with results from Osterberg Cell (O-cell) load testing, which presents a comparison between the design resistances of ultimate side friction and end bearing and the measured capacities at failure.The Old and the NewEditions of the AASHTO LRFD Bridge Design Manual from 2012 and earlier estimated ultimate side resistance, qs, in rock using the following equation (modified from Horvath and Kenney, 1979):qs=0.65aEpa(qu/pa)0.5 < 7.8pa(f ’c/pa)0.5 where: qu is the uniaxial compressive strength of the rock in ksf; pa is the atmospheric pressure in ksf; aE is the reduction factor to account for jointing in rock; and f ’c is the compressive strength of the concrete in ksi. For intact rock, previous versions of the AASHTO manual required that the ultimate end bearing resistance, qp, was calculated using the following equation: qp=2.5qu."

Jan 1, 2017

By Paul J. Sabatini, Robert C. Bachus, Terence P. Holman, Panos Andonyadis

A recent landslide comprising approximately 12 acres (4.86 hectare) and a displaced volume of more than 500,000 cy (382,000 m3) caused the shutdown of a four-lane state highway and two high-capacity freight railway lines. After completion of immediate landslide stabilization activities, various long-term slope stabilization measures were implemented that focused primarily on gradual slope unloading in areas near and upslope from the scarp of the landslide. Near the completion of the upslope excavation, an anchored soldier beam and lagging wall was constructed to allow for the temporary unloading of the toe of the main landslide area to facilitate installation of a permanent underdrain. The design of the anchored wall utilized information collected during the rehabilitation construction and included inclinometer data, site survey results, piezometer data, and field construction observations. Using the history of site-specific movements, results of back-analysis calculations from the landslide, and geometry/performance of the post-construction slope configurations, the fully softened and residual shear strengths along two potentially critical sliding surfaces were calculated. Owing to the high confidence in the values of shear strength as afforded by this information, the confidence in local groundwater conditions, and control of the loads, the designers selected a relatively low, calculated short-term factor of safety (FS) (i.e., FS ˜ 1.1 to 1.2) for the most critical unloading step. Long term calculated FS values on the order of 1.2 to 1.3 were anticipated. This paper describes the detailed evaluation of the landslide slope movement data associated with the shallow and deep potentially critical failure surfaces and selection of the associated values of design shear strength for these potentially critical surfaces. A description is presented of the analyses and design of the anchored wall, measures implemented during construction to minimize slope movements, and post-construction monitoring results during the unloading and subsequent installation of the underdrain.

Jan 1, 2017

By Monica Prezzi

"Auger cast-in-place (ACIP} piles and drilled displacement piles are being increasingly used as foundation elements for structures, particularly in projects requiring accelerated construction or involving the rehabilitation of foundations of existing, overstressed structures. Auger cast-in-place piles (also referred to as continuous-flight-auger piles) are widely used to construct the foundations of all types of structures. There are many different types of drilled displacement piles, with the installation methods varying according to the equipment used. Depending on the specific rotary piling technology used, responses ranging from those associated with non-displacement to those associated with full-displacement piles are obtained. Conventional pile design methods do not account for how the various construction techniques involved in auger piling change the soil state around the pile during installation and, hence, cannot accurately estimate the pile resistance in a consistent way. Research on this subject, identifying the different variables that must be accounted for in design and linking these variables to installation methods, is lacking. This paper describes the different piling methods available for auger cast-in-place and drilled displacement piles, the equipment used to install them and the quality control processes typically used. It also reviews some of the design methods currently used.IntroductionDeep foundations are extensively used in geotechnical engineering practice. The wide spectrum of piling methods results in a variety of pile types. Each type behaves differently, depending on the installation or construction methods. On one end of the spectrum are non-displacement piles, the classicql examples of which are bored piles or drilled · shafts. These piles are constructed by removing a cylinder of soil from the ground and replacing it with concrete and reinforcement. On the other end are full-displacement piles, such as closed-ended pipe piles or precast reinforced concrete piles, which are typically driven into the ground. Driven piles preload the materials below the toe of the pile and displace the soil surrounding the pile shaft laterally during the installation process. Therefore, displacement piles are, in general, more likely to have a stiffer response than non-displacement piles. This is true particularly in the case of sandy soils where displacement causes densification."

Jan 1, 2005

By Terrence M. Carroll, Chu E. Ho

"A pile installation and load testing program on driven tapered piles was undertaken at John F. Kennedy International Airport in New York City for the extension of the existing Terminal 4. As part of the program, dynamic testing by means of the Pile Driving Analyzer (PDA) was performed on several preliminary test piles as well as production piles. The results of the dynamic tests and subsequent static load tests were reviewed to develop an understanding of the pile-soil response of a tapered pile during driving and after setup. Pile setup occurred as a result of increase in shaft resistance with virtually no increase in toe resistance. More than 150 tons of additional capacity was gained after the setup time.The capacities measured during driving from the PDA are typically used as the basis for determining the pile driving set criteria, with the required initial driving capacities determined largely by the contractor’s experience. An improved appreciation of the setup phenomenon is required to better refine the driving criteria at the end of initial driving such that the required ultimate capacities can be obtained, with reasonable confidence, after a period of setup.This paper presents interpretation of pile-soil behavior from Case Pile Wave Analysis Program (CAPWAP) analyses and discusses the mechanism of increased capacity as a result of setup effects. Time-dependent capacity gain as a result of setup effects should be based on the extrapolation of the shaft resistance component rather than the total pile capacity as is commonly practiced. Prediction of pile performance using this approach was in good agreement with observed static and dynamic load test results.IntroductionTapered piles have been adopted for various projects at John F. Kennedy International Airport (JFKIA) since the late 1940’s. Initially timber piles were used exclusively, with steel Monotube piles being used from at least the 1980’s (Horvath and Trochalides, 2004). The steel Tapertube pile was developed in the mid-1990’s and has commonly been used in recent construction (Brusey and Yin, 2008). The Tapertube piles used for this project consisted of a 25 foot long tapered section that was 8 inches in diameter at the tip and 18 inches in diameter at the top. An 18 inch diameter straight pipe was welded above the tapered section."

Jan 1, 2015

By Thang V. Nguyen, Lisheng Shao, Gary E. Taylor

"The Community Memorial Hospital of Ventura, California, proposed to build a new state-of-the-art Cancer Treatment Center with radiation shielding walls and roof. The loose silty soils at the site had the potential to liquefy during an earthquake, which would result in significant settlement under the heavy footing loads. Treatment options included various deep foundation alternatives, as well as several ground improvement methods. The choice of wet soil mixing minimized the disturbance to the adjacent hospital during construction and potential settlement. Wet soil mixing allowed the structure to be supported on a raft foundation, meeting the stringent building total and differential settlement criteria. The authors also performed unit cell 3-D finite element analyses to evaluate the behavior of the wet soil mixing system in seismic loading conditions. This paper highlights the ground improvement design, construction, QA/QC, and the research related to evaluating the effectiveness of soil mixing for liquefaction mitigation.INTRODUCTIONThe Ventura Community Memorial Hospital proposed the construction of a new Cancer Treatment Center to replace the existing structure, which was built in 1901. The hospital complex is located in a wellestablished residential neighborhood. The soil conditions at the site of the proposed structure required ground modification to support the very heavy radiation treatment section of the building and limit settlement. Originally, 90-foot-long precast piles were considered for foundation support. Based on supplemental Cone Penetration Tests (CPTs) performed, the deepest CPT did not encounter competent pile bearing strata at a depth exceeding 30.5 m (100 ft). This could result in failure of the piles under long-term conditions, especially if hydro-consolidation occurs. The more realistic pile penetration depth would have been 36.6 to 45.7 m (120 to 150 ft). In addition, the excessive noise in association with pile driving would have been unacceptable to the community, patients, and staff of the hospital, so an alternative ground improvement solution was required.The specialty geotechnical contractor recommended wet soil mixing, an economical solution of creating a soil-cement product known as soilcrete that would significantly reduce the construction related noise and provide a more complete deep foundation for the structure.SOIL CONDITIONS AND SETTLEMENT CONCERNSThe subsurface soils were interbedded (Fig. 1) consisting of loose to medium dense silty sands, and soft to medium stiff silty clays to a depth of 30.5 m (100 ft). Groundwater was encountered at depths of 9.1 m (30 ft) and historical high groundwater was at 8.5 m (28 ft) below the ground surface."

Jan 1, 2015

By Federico Pagliacci

"Many existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or pervious rocks or karst. Remedial works are necessary in order to install new cut-off walls to stop the water flow. In some cases the cut-off walls have to be executed at depths never reached so far, and difficult to reach with traditional foundation techniques. In many cases the Hydromill technology proved to be the best system to overpass rocky layers and ensure the required verticality. The maximum depth reached by the industry was in the range of 120-150 meters. This article describes the test performed to excavate and cast in place a 3.2x1.5 m panel to a depth of 250 m. The article will also describe the stratigraphy of the site down to 250 meters, as well as the technique adopted to achieve the said depth with deviations from verticality of 30 cm along the longitudinal axis (0.12%) and 20 cm along the transverse axis (0.10%), measured at the bottom of the excavation. The concreting of the panel, for about 1,100 m³, with plastic concrete in the lower portion and conventional concrete in the upper portion will be illustrated. Finally, the tests performed during the excavation and after concrete casting will be also described, with special attention to the continuous directional core drilling that was performed along the whole length of the panel to verify the results of the deviation from verticality, through the onboard instruments, and to control the quality of concrete at a depth never reached before. IntroductionMany existing dams are subject to underwater seepage due to subsoil conditions, like deep alluvial deposits or caves and cavities or acid solutions in the bedrock formations.Conventional remedial works generally consist in the construction of an additional cut-off wall throughout the dam body and the subsoil, in most cases being deeper than the original one. Today, many examples of successful remedial cut-off walls allow the engineers to design the most suitable solution according to the dam and subsoil characteristics and nature.The real difficulty stems from the depth at which the new cut-off wall has to be socketed in competent rock or soil, so as to eliminate underwater seepage. The maximum depth ever achieved with a cut-off wall is 122.5 m for the remedial work of Mud Mountain Dam, Washington, USA, in 1988-1990. This 0.85-1.0 m thick cut-off wall was realized by means of a Hydromill, by excavating single 2.8 m-wide secant panels."

Jan 1, 2017