Search Documents

By Vahid Tajdar

The behavior similarity between pile and cone penetration test, has guided the researchers to use the CPT results in prediction of piles bearing capacity. In this article, artificial neural networks have been used to study about relation between cone tip and sleeve friction strength obtained from cone penetration test and ultimate pile bearing capacity, obtained from static pile load test. Artificial neural networks "ANNS" is a form of artificial intelligence. ANN tries to dramatize the human nerves & brain system biology structure in self-structure. In this article, the results of relevant studies about the prediction of ultimate pile bearing capacity in especial area of soils are presented by use of back - propagation neural networks. The results of static pile load test up to failure on 63 piles with closed end and CPT test results in the place of construction these piles use in order to confirm and creation ANN model. Comparing predicted ultimate pile bearing capacity by utilizing ANN with the numbers which are predicted by 5 common traditional methods shows that using of artificial neural networks is a suitable method for predicted ultimate pile bearing capacity in identified area of texture of soil moreover it has a better operation in comparison with common traditional methods.

Jan 1, 2006

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibrations generated during the driving of piles or sheet piles can affect buildings or installations in the ground. However, observed building damage is not always caused directly by dynamic effects, but can also be related to foundation conditions. The importance of geotechnical conditions is usually not taken into consideration in most vibration standards. This paper describes how building foundations, and in particular mixed foundation types, are especially sensitive to ground vibrations. A method is presented for assessing the risk of settlement due to vibrations in granular soils. Also, a simple concept is proposed for estimating settlements in the vicinity of driven piles.1. INTRODUCTIONUnder unfavorable conditions, the installation of piles or sheet piles can cause damage to buildings or other structures on the ground. Frequently, such damage is attributed to vibrations of the building itself. In many countries, national or international standards are used to assess the risk of vibration damage to buildings. As such standards are often prepared by engineers with little or no geotechnical knowledge, the effects of ground conditions on vibration propagation and damage to building foundations are generally not recognized, and damage criteria based solely on the dynamic response of buildings neglect the importance of damage mechanisms governed by geotechnical conditions. One potentially important damage mechanism is differential settlement below buildings, especially when these are founded on loose granular soils. When seeking guidance in the literature, little or no information can be found regarding methods to assess permissible levels of ground vibrations with respect to risk for settlement.This paper focuses on building damage that can be attributed to foundation conditions. In the case of ground vibrations due to pile and sheet pile driving, differential settlements are of particular importance as the ground vibrations attenuate relatively rapidly from the source. Consequently, settlement below part of the building, which is located close to the vibration source, can be significantly larger than at a distance further away.Piles are often a cost-effective foundation solution for buildings on loose and compressible soil, frequently located in urbanized areas. Sheet piles are commonly used as support for deep excavations. While impact driving is most commonly used to install piles, vibrators are frequently used for driving (and extraction) of sheet piles. It is important to recognize the fundamental differences between impact and vibratory driving. During impact driving, the pile is subjected to stress waves of short duration. The driving process creates vibrations, which radiate from the shaft and/or the toe of the pile into the soil. The larger the intensity of the stress wave, the larger the dynamic force and the intensity of ground vibrations. In addition to the vibration intensity, which often is expressed in terms of particle velocity, also the vibration frequency is important. When the dominant frequencies of the generated vibrations harmonize with the resonance frequency of buildings or building elements, the risk of building damage increases."

Jan 1, 2014

By Mark X. Haley

Foundation design and construction in Boston has changed dramatically during the past 10 years. Prior to 1985, the primary foundation element in Boston, where deep foundations are required, was driven end-bearing piles. Since 1985, drilled or excavated high capacity foundation elements have been utilized more frequently. This paper will provide a historic perspective of their use and a summary of design parameters for elements installed and founded in the bedrock. TOPOGRAPHY Boston was founded in 1630 by the Massachusetts Bay Company of John Winthrop and his hearty band of Puritans. The settlement was chosen for: ? its safe harbor, ? abundant source of fresh water, and ? peninsula setting offering protection of the ocean on almost all sides with high ground for fortification. These three factors were a direct result of past geologic processes that created the Boston Basin by erosion of the soft bedrock underlying this area as compared to the harder granite rock to the north, west and south. As the glacial ice sheets melted and moved northward, various soil types were deposited. During ice sheet re-advancement the hills and islands of Boston took on their precolonial shapes. The Trimont, consisting of Beacon, Mt. Vernon and Pemberton Hill, rose to 150 ft above sea level with the smaller Copps and Fort Hill to the north and south.

Jan 1, 1994

By Robert F. Stevens, Robin Givet, Kenneth Viking

"Summary This paper describes a case of a directional pile installation conducted from an existing oil platform in the Caspian Sea, offshore Baku. Results are presented for 660 mm outer diameter (660 mm OD) conductor piles. Each conductor was equipped with a beveled aluminum toe for directional impact driving and was driven through a 710 mm casing using a Delmag 100–13 diesel hammer and a chaser pile. The 710 mm casings were preinstalled to a depth of 75 m below mud line (75 m BML). The longest impact driven conductor pile on the project was 456 m at end of drive, and reached the terminal depth of 295 m BML.Soil conditions consisted of soft to stiff silty clay to a depth of 30 m BML, underlain by stiff clay to 96 m BML, very stiff silty clay to 200 m BML, and very stiff to hard clay down to 300 m BML.In order to assess the maximum stresses in the conductors and check the performance of the hammer, the driving of each conductor was monitored using a Pile Driving Analyzer (PDA). The hammer fuel setting was adjusted based on the PDA outputs to ensure the conductors were not overstressed during installation. All driving and monitoring operations were carried out from the drill floor.The conductor piles drove easier than anticipated but in the direction predefined by the pre-cut angle of the beveled aluminum toe. The driving system performance was good. Post driving, the SRD were analyzed by either the global method analysis, using WEAP, or by the CAPWAP program.To detect any collision between the conductor being driven and the adjacent wells in production, the well heads were monitored in real time with high sensitivity accelerometers. These accelerometers were connected to an alarm system on the drill floor, triggering a siren and a strobe light should a collision be detected by an abnormal increase of the peak acceleration.IntroductionThe world longest directional impact driven pile was installed in year 2005. The operation was carried out from an offshore production, drilling, and quarters (PDQ) platform located about 120 km east of Baku, in the Caspian Sea.The platform foundation consists of driven piles and 24 slots were available for drilling the wells to the reservoir, located about 3800 m below sea floor. Each slot was fitted with a casing, 710 mm in diameter, running from the top of the jacket to a depth of about 75 m BML (Figure 1). Oil production started in 1997 and by the end of 2003, 14 wells were in operation; 10 slots were therefore still available, either for oil production or for water injection. However, due to larger than expected settlement of the platform, drilling of additional wells was put on hold. After further investigation, experts concluded the settlement was due to an alteration in the mechanical properties of the bearing strata supporting the foundation piles. This alteration was due to either excess soil material transportation, or soil fracture by the drilling fluids (mud), when drilling the first wells. With only 14 wells in production, out of 24 possible, the owner faced a new dilemma: to drill, or not to drill new wells?"

Jan 1, 2014

By Gunhild Hennum, Tewodros Tefera, Gisle Håland, Annette Jahr

"Abstract The Gudrun field is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected to support the topside and was installed in 2011. The jacket shall be able to support 16 of 0.762 m (30 in) diameter conductors and is equipped with a drilling deck to allow for pre-drilling by a jack-up rig through the jacket. In general the soil conditions below mudline comprise of a thin top layer of very loose to dense sand overlaying several layers of sandy clay, ranging in stiffness from firm to hard. Below some 30 m depth the soil consists of layers of medium dense to dense silty sand overlaying very hard sandy clay containing thick beds of sand to 100 m depth or more below mudline. The jacket is secured to the seabed by twelve 2.438 m (96 in) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. Different design methods were used to determine the pile penetration depth. Pile drivability was evaluated using best estimate and upper bound soil parameters. The pile driving and blow count record show that the target penetration was reached as predicted. This paper discusses the different methods used to determine the pile capacity, target penetration depth and the drivability analyses made for the Gudrun jacket piles. The soil resistance during pile driving is back-calculated from the pile installation data and compared with the prediction made.IntroductionThe Gudrun platform is located west of Stavanger in the North Sea at water depth of 109 m. A jacket substructure was selected for the Gudrun platform. The general Gudrun platform jacket configuration is to a large extent dictated by the topside layout, the requirements for support points enclosing the well slots and access for the jack-up rig. The Gudrun platform jacket is a traditional 4 legged structure with a vertical side towards the jack-up rig. At the seabed the jacket is quadratic with a base dimension of 40 by 40 metres. Figure 1 shows the Gudrun jacket during load-out from the fabrication yard to the transport barge. At the site the jacket was lifted off the barge, upended and placed on the seabed by the installation vessel. The jacket is secured to the seabed by twelve 96"" (2.438 m) diameter steel pipe piles, three at each pile cluster located at the four legs of the jacket at sea floor. The target penetration of the piles is 47 m."

Jan 1, 2014

By Mohammed Sakr

The use of helical piles for permanent foundation applications has become a practical and feasible alternative to the traditional cast-in-place concrete or driven steel piles. Research and development, installation equipment and manufacturing improvements in the helical piling industry have led to this trend. Moreover helical piles are typically smaller in size and weigh less than traditional piles, and require relatively smaller equipment and therefore it is a cost effective option. The latter is a very attractive feature for foundations installed in remote sites across Alaska. This paper presents full-scale pile load test results of helical piles and driven steel pipe piles installed in a site located in Anchorage, Alaska. Four full-scale pile load tests were carried out including two axial compression and two uplift load tests. Both helical piles and driven steel pipe piles were installed and tested at the same site under similar conditions to provide a direct comparison. The results of the full-scale load tests indicate the superior performance of helical piles compared to driven steel pipe piles. This paper describes the pile installation and test setup, presents the test data, and discusses the results.

Jan 1, 2009

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2000

By J. Nakayama

For installation of round steel piles or cast-in-place pile construction through boulder contained ground or rocky formation, usual system does not function properly or impossible to work. This paper introduces an installation system which combines unique mechanism where the drill is installed on the top of a driving round steel pile or a stand pipe which is initially driven into the overburden to the depth of self-standing. When the pile driving or bore hole drilling encounters hard strata or boulder contained ground, hard material shall be crushed by the down-the-hole chiselling operated in adjustable short stroke and high frequency of blows while cuttings are discharged in reverse circulation through central reverse pipe while round steel pile is simultaneously stroked by a hydraulic hammer. The paper shall explain the mechanism of the system and introduces construction examples for bridge foundation and piled jetty.

Jan 1, 1999

By Roy Jennings

The Discovery Expedition of St. Charles, MO chose to build its two-story museum in the flood plain of the Missouri River, near the starting point of the Lewis and Clark Expedition. Should the lower level be inundated at flood stage, plans call for the replica riverboats to be moved by trailer to higher ground. The museum's design required an open span structure with heavily loaded footing or piles. Spread footings could not be used due to the compressible soil profile. The location, in a historical district, precluded dynamically driven piles. Sixty-three uncased Helical Pulldown Micropiles were driven to the bearing stratum to support the museum with minimum disturbance. There were no spoils to dispose of during construction and the piles were completed in eight working days with minimum impact to the environment and neighborhood. The maximum working load required was 84,000 pounds (374kN). Test results are given in the form of installing torque.

Jan 1, 2003

By Dimitris Pachakis

In this paper, the authors give a brief overview of the current practice guidelines and tools for the seismic design of sheet pile quay walls, emphasizing how the design guidelines are lacking when the existing structure performance evaluation is required to meet performance-based criteria. Relying on recent experience they explain how the existing practices can be amended to focus more on performance evaluation as opposed to design. An example is given of an old sheet pile quay wall analyzed and evaluated for its performance according the recent performance criteria devised for Californian Marine Oil Terminals.

Jan 1, 2011

By David A. Staab

Numerical modeling was used to investigate the feasibility of using two geophysical imaging techniques, cross-borehole ground penetrating radar (XBGPR) tomography and electrical resistivity (ER) tomography, for detecting and characterizing defects in deep-mixed soil columns. XBGPR modeling was accomplished with a three-dimensional numerical forward modeling code and a two-dimensional inversion routine. Spatial variations in apparent dielectric constant (Ka) and attenuation (a) were mapped. Electrical resistivity modeling was accomplished with a three-dimensional numerical forward modeling code and a three-dimensional inversion routine. Spatial changes in electrical resistivity were then mapped. Three different types of defects were simulated, in addition to a defect-free column. The computer simulations suggest that XBGPR tomography and ER tomography might be useful, non-destructive methods for detecting and estimating the extent of defects in deep-mixed soil columns. The results show that small, isolated defects might be difficult to detect, but defects approximately equal to or larger than the sampling interval (for XBGPR) or vertical electrode spacing (for ERT) should be detectable.

Jan 1, 2004

By Steven R. Musselman

The bending strength and flexural stiffness of a micropile at its threaded connection is less than its intact strength and may fail due to thread slippage or by fracture through the pin (reduced cross-sectional area of male threads in the threaded zone of the casing). The mode of failure depends on the reduction in cross-section necessary for machining the threads, and details of the threaded connection such as the length of threaded connection, size and shape of threads, and the thread density (threads per inch). Based on data from bending tests conducted on 9-5/8 inch diameter micropile casing, a method has been developed to predict the ultimate moment capacity and initial bending stiffness of round threaded micropile connections. Two modes of failure were observed from four-point bending tests conducted at the University of Illinois on 9-5/8 inch casing with round threads. Threaded micropile casing connections with an effective thread length of 1.35 inches typically failed by slippage at the threads (jump out), while connections using an effective thread length of 1.89 inches failed by fracture of the pin. These two failure modes were described by W.O. Clinedinst in his report to the American Petroleum Institute on tension tests of threaded pipe casing. Clinedinst developed an empirical formula to determine the tensile strength of threaded connections. A method to predict moment capacity for threaded micropile connections by modeling the micropile cross-section and applying Clinedinst?s equation to determine the max tensile stress along the threaded connection while satisfying force equilibrium is proposed. The predicted moment capacity for threaded connections using this approach is within ten percent of measured for both modes of failure observed from the bending tests.

Jan 1, 2007

By Mike Muchard

STATNAMIC load testing augmented with embedded instrumentation has been successfully used to obtain structural and geotechnical design information on large diameter spun cast concrete cylinder piles on many large marine construction projects. The paper focuses on one particularly interesting large marine project involving a new bridge to St. George Island, Florida where instrumentation and STATNAMIC load testing was used in conjunction with static load testing on high capacity piles. The information presented includes embedded instrumentation measurements taken during pile fabrication (post-tensioning), during pile driving, during static load testing, and STATNAMIC load testing. As much of this data is the first of its kind on concrete cylinder piles, it is exciting to present the foundation industry with this additional insight as to the behavior of this pile type and the accuracy of the methods used to test them.

Jan 1, 2005

By Lisa M. Splitter

Drilled displacement piles were constructed as the foundation for a proposed 10-story building in San Francisco, California. At the study location, the stratigraphy consists of 14 to 21 feet of fill and 13 to 23 feet of weak, compressible clay (?Bay Mud?), underlain by dense sand, stiff clay, and bedrock. A sensitive critical public utility is located within approximately 20 feet of the constructed piles along one side of the building. The utility pipeline is entirely within the Bay Mud where it is adjacent to the project site. The San Francisco Public Utilities Commission (SFPUC) developed limits on the allowable total and differential movement of the utility pipeline. As requested by the SFPUC, inclinometers and piezometers were installed to monitor the soil movement and pore pressure increases in the Bay Mud caused by the installation of drilled displacement piles. Action levels were set such that if displacement and/or pore pressures reached an action level, the installation methodology would be reevaluated and additional measures to reduce these effects would be implemented. This paper will present the sequence of pile installation near the pipeline and monitoring points, and the data collected from inclinometers and piezometers at variable depths and distances from the piles. The data will highlight the build-up and dissipation of pore pressures over time and the displacement of Bay Mud caused by the pile installation. The conclusions of the study are useful in determining sequencing, spacing, predrilling, and other measures that can be implemented to decrease the displacement potential and pore pressure build-up in soft clays.

Jan 1, 2009

By Richard J. Finno

This paper presents an overview of methods that can be used to predict damage to buildings as a result of excavation-induced ground movements and describes an adaptive management approach for predicting, monitoring, and controlling excavation-induced ground movements. Successful updating of performance predictions depends equally on reasonable numerical simulations of performance, the type of monitoring data used as observations, and the optimization techniques used to minimize the difference between predictions and observed performance. This paper summarizes each of these factors and emphasizes their inter-dependence. Case studies are presented to illustrate the capabilities of this approach. Examples are given to show how optimized parameters based upon data obtained at early stages of excavation can be used to predict performance at latter stages, and how they can be applied to other excavations in similar geologic conditions.

Jan 1, 2010

By Robb L. Swenson

Construction of foundations for the Skyway Segment of the San Francisco Oakland Bay Bridge required innovative techniques due to the mass of the structures being inserted and the unique subsurface of the Bay. Twenty of the pier structures required large sheet pile cofferdams. Eight other foundations were installed in open water without cofferdams at the deeper part of the Bay. This narrative will present the initial planning, as well as the stages of installation, for each type of foundation. The first section will discuss foundation constructability modifications made during the initial planning phases of the project. Considerable effort was expended by Caltrans, the owner, T.Y. Lin the designer, and KFM (Kiewit/FCI/Manson) the contractor in modifying the design to assure that required tolerance would be maintained during the installation of the foundations. The final section will describe the steps required for installation including: initial access dredging, installation of cofferdams, preparation required to install the footing boxes, footing box installation, foundation support pile installation, and pile to box connections.

Jan 1, 2005

By Peter Middendorp

Pile foundations are widely applied in the Netherlands because of the soft soil conditions. One of the popular pile types are cast-in-situ piles, which have to be integrity tested to get accepted. Integrity testing has been applied for more than 30 years, with the number of integrity test performed nowadays exceeding 400,000 per year and subsequently there is a substantial amount of practical experience with this testing method. This paper will deal with some basics of integrity testing and describe some of the techniques that have been adopted in the Dutch pile testing practice, like detection of pile head defects with a spike type hammer pulse, and the site average or pile group average for the qualitative interpretation of measured signals.

Jan 1, 2006

By B. M. Das

Laboratory model test results for the ultimate uplift capacity of rough rigid single and group piles embedded in sand have been presented. Model tests on single piles were conducted in loose, medium, and dense sand. The uplift tests on group piles were conducted in medium sand only. Based on the present model test results, tentative relationships for the estimation of the ultimate uplift capacity of single pile have been presented. The efficiency of group piles is a function of the length-to-diameter ratio, center-to-center spacing to diameter ratio, number of piles in a group, and the degree of compaction of sand.

Jan 1, 1989

By Frances Badelow

This paper describes a design process for piled raft foundations supporting high-rise buildings. The design process comprises an initial stage of geotechnical site characterization using the results of investigation boreholes to prepare a subsurface model and derive geotechnical parameters for raft and pile design from empirical correlations. Following this a preliminary analysis is undertaken using a combination of elastic theory and allowances for non linear behaviour of the piled raft system to assess the viability of such a foundation system and any potential advantages of a piled raft over conventional fully piled foundation systems. Finally, a detailed analysis is undertaken using the GARP8 computer program. Case studies where this design process has been successfully used to design a more efficient piled raft system that has resulted in significant cost and time savings compared to conventional bored pile foundation options are also described.

Jan 1, 2006

By A. K. Bhattacharya

Cylindrical bridge piers are widely used and equations exist that can predict the maximum depth of local scour around such piers. Scour around piers is an undesirable phenomenon, as it requires the foundation to be placed to a greater depth resulting in increased cost, making it worthwhile to investigate scour-reducing measures. A number of scour-reducing measures have been tried out for cylindrical bridge piers including placing a concrete collar around the pier, having a delta-wing projecting upstream in front of the pier, placing riprap around the pier, using a group of piers instead of a single pier, having a slot in the pier aligned in the longitudinal direction. The objective of this study is to investigate the effect of upstream protective piles on reduction of maximum local scour depth around a cylindrical bridge pier. The upstream piles are placed at different radial distances in front of the pier and the scour depths are observed. The proposed equation of Dey (1997) for determining the maximum depth of scour around a cylindrical bridge pier is used. The reduction of local scour around the pier is compared with local scour around an unprotected pier.

Jan 1, 2009