Search Documents

The purpose of this paper is to describe briefly the clean-up procedure adopted at the treatment plant of Paringa Mining & Exploration Co. Ltd. at Kalgoorlie, Western Australia.A clean-up is carried out at the end of each four-weekly period, and all figures subsequently quoted are taken from a summary of the results of the eight periods ending 8th April, 1941.STRAKING AND AMALGAMATIONOf the total gold won 22· 77 per cent. is recovered by straking and amalgamation.The discharges of both the primary and secondary ball mills are pumped over a common set of five ten feet long by three feet wide straking tables, set at an angle of 10 degrees, before passing to the 14 ft. diameter by 30 ft. by 8 ft. Dorr bowl classifier.This classifier is in closed circuit with both of the ball mills, hence the whole of the circulating load of the fine grinding circuit, which approximates to 800 per cent., is required to pass over the straking tables. For convenience in handling, corduroy cloths are used in lengths of 5 feet, and are picked up and replaced by clean cloths at four-hourly intervals. The avaHable straking area provided is, therefore, 900 square feet, or approximately 3·30 square feet per original ton per 24 hours. The density of the pulp passing over the tables is about 54 per cent. solids, the area provided per ton of pulp per 24 hours being approximately o· 2() square feet. Washing of the corduroy cloths is carried out on the day shift only, about 800 lb. of strake concentrate being obtained daily.This concentrate is sluiced from the washing trough on the elevated straking floor to the 4 ft. by 2 ft. diameter amalgamating barrel located in the gold room below.The barrel is of standard design and is rotated at 25 r.p.m. It is charged each day at 4 p.m., and grinding of the strake concentrate at approximately 70 per cent. solids is continued until 8 a.m. the following day. The barrel is then stopped, and the contents generously diluted with water, and after a few minutes rotation some of the slime is carefully poured off through the small discharge hole. This dilution and decantation is repeated until a good deal of the valueless slime has been removed.A further quantity of strake concentrate is then charged to the barrel, which is allowed a further 16 hours grinding period. After again diluting and decanting, approximately 25 lb. of mercury and 15 lb. of lime are added to the charge, which is then given an amalgamation period of 2 hours before cleaning up.By the process of grinding, diluting and removal of slime by decanting...

Jan 1, 1941

By M. Botz

For leach solutions containing primarily free cyanide, the silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method significantly over-estimates the concentration of free cyanide and under-estimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric titration method for determining WAD cyanide that overcomes issues with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to fully release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, accurate WAD cyanide measurements were achieved using the MP-WAD method. Analyses obtained with the new method were found to be within about ±10% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.

Feb 27, 2013

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By A. Lyndon

Vertical and lateral load tests were carried out on two 13 m deep bored cast-in-place instrumented piles, socketed into weathered sandstone. The first pile, 1200 mm in diameter, was loaded vertically to a maximum of 16000 kN and then loaded to failure under lateral load (1900 kN). The second pile, 1500 mm in diameter, was tested under lateral load up to a maximum of 2400 kN. It was found that the deflections of the 1200 mm pile were more than twice those of the 1500 mm pile under similar loads. The soils on the site are not easily tested in the laboratory, or by conventional insitu site investigation techniques, parameters needed in design can only be reliably obtained from pile test results. In this report shear moduli are back analysed from the vertical load test and the two lateral load tests. For these similarly installed piles very different design parameters were determined from the lateral load tests, the only known major difference between the piles being that the 1200 mm pile was loaded vertically before it was loaded laterally. Changes in G values needed to match performance under vertical load if applicable to lateral loading could have accounted for a significant amount of the difference.

Jan 1, 1989

By H. C. Fuller

This paper discusses 105 production runs at Boulder City, Nev., in which titanium metal was made in 200-pound batches. It describes the equipment and techniques used in preparing raw material, the reduction process, and the removal of the reaction mass from the reaction vessel. Also, some data on man-hour requirements are presented. The main emphasis was on producing ductile-grade titanium and developing a standard procedure for obtaining a consistently pure product. Some departures from techniques used before were found to be desirable. The most important of these was the use of a sealed room with a controlled dry atmosphere in which the reaction vessel was opened and the reaction mass removed. This minimized the moisture taken up by the magnesium chloride in the reaction mass, and it could be purified successfully by vacuum distillation. Using the dry room also made it possible to leave al-inch shell of the reaction material on the walls of the vessel, which lowered the iron contamination and eliminated the labor and time-consuming job of cleaning the vessel after each reduction. Another change was lowering of the temperature during reduction to 750° C. instead of 850° C. This was found to give good results more consistently. The first poke to break the crust during reduction was eliminated, as it was found to be unnecessary and only added more work and was another possible way of introducing air. A rotating feed arm was installed in the reaction vessel to distribute the titanium tetrachloride over a larger area and, thus, prevent local overheating. The process, conducted in a batchwise manner as described and followed by good purification and fusion, produces a metal adequate in quality for nearly all purposes.

Jan 1, 1952

By A. M. Ouchi

Existing empirical design tools have been developed from fair-to-good quality rock masses (RMR76 >50). This paper presents a focus of ground control research presently being conducted by the Rock Mechanics Group in the UBC Mining Department in incorporating weak rock masses (RMR76 <50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented with over 450 weak rock data points from mines such as the Stillwater mine (Montana), the Eskay Creek Mine (BC) and several mines in the Carlin Trend and other parts of Nevada. The original database is comprised of spans supported with ?traditional? mechanical bolting. In weak rock environments however, this type of support has been found for the most part, ineffective. This paper presents the span and weak rock RMR76 relationship for four different support categories. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

Jan 1, 2008

By S. Dessureault, J. Porter, M. Woodhall

Information and communication technology (ICT) is seen as a key source of future productivity improvements in mines. The information technology infrastructure (ITI) necessary to achieve these productivity improvements will come in the form of data integrated from multiple source systems throughout the mining value chain. Two pure approaches are available: supplier-controlled or operations controlled data structures; each strategy has its own advantages and disadvantages. Case studies involving the South African mining industry are used to demonstrate the advantages of using hybrid-controlled data structures. Depending on the level of operational control, new skills are also necessary to be learnt by mining professionals including: information engineering; creating consistent and quality data; and process improvement techniques that use the integrated data for improving the operation.

Jan 1, 2004

By Andreas Brandner

"At the beginning of 2007 the Austrian contractor PORR was awarded with remediation works for a 48-km long part of the railway line from Campina to Predeal – part of the Trans European main Corridors TEN-T priority line 22 Bucurest – Brasov, connecting the southeast European countries with the heart of Europe.Due to partly new realignment and change of regular sections as well as protection against rockfall and slope slide a huge bunch of slope stabilization works became necessary, which were awarded to the contractor PORR and their designer IB-Brandner.Following the studies of the tender documents for the planned protection measures responsible managers of PORR decided to propose an alternative protection design by IB- Brandner. Changing the original design a more flexible and environmentally compatible solution consisting of high performance net, soil nailing and rockfall protection systems (fences) was elaborated and adapted to local needs. During design process, several critical areas were identified and additionally taken into account.In the paper examples of the design and erection process show how difficulties in implementation starting with the presentation of the idea continuing to the realization on site were managed and a technically more sophisticated and commercially competitive solution could be delivered to the customer Romanian Railway – case study.The European Commission awarded – following an election process in which all citizens of the EU could join - the remediation project Railway line Campina – Predeal in Romania as the environmentally best EU co-financed infrastructure project. GENERAL PROJECT EVALUATIONDue to original design slope stabilization should be done by concrete slabs fixed with prestressed anchors and shotcrete cover.The area to be secured was limited to a 12-meter strip left and right from the railway track without reference to nature and local needs. Discussions with the client and his designer and rising awareness for the hazards to address took several months. Site visits in Austria to provide insight in the problems of dealing with natural hazards helped to convince the client of the needs and our alternative design."

Jan 1, 2017

By J. P. Welsh

Ground Modification construction is rapidly evolving in the United States. An assessment of the construction status of Ground Modification methods with their dates of introduction and general acceptance in the United States is summarized. Seven of these techniques are discussed in depth with short case histories; namely, Dynamic Deep Compaction, vibro-compaction, vibro-Replacement, chemical grouting, compaction grouting, slurry grouting and jet grouting. Additional case histories are presented to illustrate the trend of combining Ground Modification techniques to solve specific site problems.

Jan 1, 2010

By Mario Paredes Malca

El presente trabajo describe el sistema experto por circuito de molienda desarrollado en la Concentradora Toquepala, donde se aplica la tecnología del control experto-basada en conjuntos difusos y modelos matemáticos. Las ventajas que presenta la aplicación de los sistemas expertos comprenden el aumento de la capacidad de tratamiento, la disminución del costo de operación y del porcentaje del producto que no cumple las especificaciones. Asímismo, el sistema experto se integra al sistema de control para asistir al operador en la detección de los casos, donde las operaciones se puedan descontrolar, aunque ésta no sea realmente su principal función. Si se le configura y sintoniza correctamente, el sistema experto detecta, diagnostica en forma continua los problemas de operación y aplica modelos matemáticos y estadísticos de optimización, interactúando con un sistema de control DCS o PLC.

Sep 12, 2005

By R. L. King

This report describes a method for designing and constructing ground beds that has been developed under the sponsorship of the Bureau of Mines. The procedures for designing and constructing a driven-rod ground bed with a resistance of 5 ohms or less are given. Some of the theory of soil resistivity and fall-of-potential resistance measurements is included. Results of a bed constructed at the Bureau of Mines mine car roadway are presented.

Jan 1, 1978

By G F. Brent, R D. Hart, C Carr, F Felipe

In underground operations, where copper, gold and other metals are mined, the open stopes can be backfilled to stabilise surrounding workings. This fill may consist of tailings from the processing plant, usually mixed in slurry with a binder such as ordinary Portland cement (OPC). Extensive use is made of tailings in OPC-based paste fill, cemented hydraulic fill or cemented aggregate fill applications. A large underground operation such as the Mount Isa Copper Operations utilises over three million tonnes of backfill per annum. Geopolymers offer an alternative binder system with significant environmental advantages over OPC. Geopolymers are formed by polymerisation of aluminosilicate precursors in an alkali medium. They generally form products with superior strength characteristics as well as increased resistance to degradation, particularly under acidic conditions. Geopolymers have lower carbon dioxide emissions associated with their manufacture than OPC and offer further potential advantages, such as the use of less water and more waste materials. The application of geopolymers to weak material systems such as mine backfill has not been widely studied. The aims of this investigation were to assess a range of Australian mine process wastes for suitability as feedstocks in fill applications and to construct a range of these cemented minefills using a geopolymer binder. The physicochemical characteristics of each of the wastes are discussed as well as how they ultimately contribute to the geopolymer cement through direct replacement of OPC. Results from various tests on the candidate geopolymer fill formulations are presented and the potential of such fill formulations to replace OPC in mine backfilling operations is highlighted. The significant potential contribution to reducing greenhouse gas emissions from the use of geopolymer-based mine backfill across the industry is noted. Conversion of a single mine, such as the Mount Isa Copper Operations, is shown to match the reductions in greenhouse gas emissions due to the current total installed photovoltaic electricity generation capacity of Australia. A similar examination of wastes available to a gold mine could potentially yield new binders for use in established or new fill systems.

Jan 1, 2007

By C. A. Brown

"Steady-state simulation has been used for over 20 years to optimise the operation of crushing and grinding circuits. Throughout that period continuing comminution research has been the basis for improving the models.Site surveys, ore characterisation, model development and investigation of different operating scenarios by simulation has proved to be a cost-effective method for improving plant performance. In this sense, this paper presents findings from experience with these valuable optimisation techniques with reference to specific case studies."

Sep 12, 2005

By Daudi R. Waryoba

Keywords: Wire Drawing, OFHC Copper, Recrystallization, Orientation imaging Microscopy (OIM), Texture inhomogeneity Textural inhomogeneities have been investigated in oxygen free high conducting (OFHC) copper wire drawn at room temperature to a true strain of 2.31, and isothermally annealed at 250°C and 750°C for annealing times ranging from 10 s to 1 hr. Local orientations were mapped by means of orientation imaging microscopy (OIM). The microtexture of the drawn wires showed a strong <111> + weak <100> duplex fiber texture at the inner core, whereas the mid and surface regions had a comparatively weak texture. Annealing at 250°C resulted into a recrystallization which originated from the mid section, proceed towards the surface regions and ends in the inner core. Recrystallization resulted into a strong<100>+weak<111> duplex fiber texture. A similar textural inhomogeneity was observed during short annealing at 750°C. However, prolonged annealing gave rise to abnormal grain-growth that proceed from the inner core to the outer surfaces with a dominant <111> fiber component at the inner region and mixed components of <111>, <100>, and <112> at the outer surfaces.

Jan 1, 2005

By Jian Yang

The mechanism of resulfurization in the desulfurization process with magnesium vapor produced in situ by aluminothermic reduction of magnesium oxide was clarified in the present work. The influences of various operating parameters on the resulfurization were studied and the methods that could prevent resulfurization were proposed. There are two kinds of mechanisms of resulfurization in the desulfurization process with magnesium. One is decomposition of the desulfurization product of MgS under the inert atmosphere. The other is oxidation of MgS under the oxidative atmosphere. Under the present experimental conditions, lowering operating temperature and oxygen partial pressure in the atmosphere could effectively prevent the resulfurization. Adding CaO onto the melt surface was an effective method for preventing the resulfurization due to transformation of the desulfurization product of MgS into the more stable compound of CaS. Since addition of the activated charcoal powders greatly decreased the transfer rate of oxygen in the atmosphere to the melt surface, it also reduced the resulfurization remarkably.

Jan 1, 2006

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

When the first rush of miners took place on the Molyneux River, in the Dunstan Gorge, the gold was won by means of cradling the gravel, which was shovelled from the various beaches and crevices in the rock-bound sides of the river.The above method of winning the gold was only practicable when the beaches were not covered with water, hence the work was usually carried on during the winter months, the ordinary level of the river during spring and summer months being some ten or twelve feet above winter level. The melting of the spow in the Lakes water-shed being responsible for the high summer level of the river.As the available beaches were worked out, other methods of winning the gold were proposed and worked with more or less successful results the first advance being to work the bed of the river by means of a spoon dredge. The spoon was made with a round lip or ring of iron, having a steel cutting edge on one half of the circumference, at the opposite side a socket being forged to take a long spar or boom, which was securely fitted thereto. At intervals round the hoop, half-inch holes were bored to enable. a bullock-hide bag to be laced on to same. The spoon was worked from a pontoon which carried a crab winch, tackles and the necessary washing appliances to treat the washdirt lifted. In starting to dredge, a tackle was attached to near the upper end of the boom, and a line or chain was carried over a cat head from the crab winch...

Jan 1, 1901

By P Atkinson, M P. Simpson, J R. Kyle

BM37 is a bonanza-grade (&gt;30 ppm Au) ore shoot of the Maria Lode of the Karangahake adularia-sericite epithermal deposit in the southern Hauraki Goldfield. Samples from BM37 contain up to weight percent gold. The ore shoot is a vein that pinches and swells, but is typically tens of cm thick, and locally exceeds 0.5 m in true width. Gold occurs as irregular anhedral electrum grains that range up to 300 microns across and contain 38 to 59 wt&nbsp;per cent&nbsp;Au (ave. 52 wt per cent&nbsp;Au). Electrum occurs in sulphide-rich bands in association with pyrite, chalcopyrite, acanthite, galena, sphalerite, and local covellite. Lower grade samples contain local to rare mckinstryite [(Ag, Cu) 2S] and polybasite [(Ag, Cu) 16 (As, Sb) 2S11]. Pyrite from BM37 is nearly stoichiometric; it lacks the As that commonly occurs at up to percent levels in pyrite from other veins in the goldfield. Acanthite also contains low quantities of trace metals, and typically has less than 2.5 per cent&nbsp;Se. The vein shows complex textures. Bonanza grade sulphide-rich ginguro bands form discrete layers adjacent to the vein margins, and occur as breccia fragments encased by later massive to comb quartz with local quartz after platy calcite. Both the breccia fragments and ginguro bands are cross-cut by later quartz veins. Textures thus indicate that formation of the high-grade portions of BM37 resulted from one or more discrete events that differed markedly from the events that formed the bulk of the vein.

Jan 1, 2006

By J. H. Adkins

The goal of the project reported in this paper was to make recommendations for changes in roof bolting procedures and bolter design that would reduce roof bolter accident rates. To that end the project identified the major hazards associated with each task a roof bolter operator per-forms, normalized task accident frequencies. by the time spent on each task, reviewed equipment design features and operating procedures related to the identified hazards and developed recommendations for equipment and procedural changes that would reduce, if not eliminate, the hazards. The research steps completed during the project were: a. A review of related literature and re-search including roof bolting time studies b. The collection and analysis of 1975 accident data pertaining to roof bolter activities c. The normalization of the accident frequency data on the basis of time/task data d. A review of roof bolting equipment e. The development of a field data collection instrument f. The selection of mines for bolter observations g. The collection of field data h. Data analysis and problem specification i. The development of recommendations for corrective measures

Jan 1, 1978