Search Documents

By Abhoy Mukherjee

The Luanshya Smelter is a traditional Reverberatory Smelter which once worked with up to three coal-fired reverbs, and now operates one Reverb and one hot Peirce- Smith Converter, projected to produce approximately 42.000 tons per year of copper anodes. The aim of this study is to select a smelting technology which best fits the upgrading of the Smelter, such that low capital and operating costs are achieved for the projected design production capacity of 60.000 tpy, limited by the available supplies of concentrates. An equally important requisite is the compliance of present and future environmental regulations, which determines the need to install and Acid Plant to treat the smelter primary gases. In the process selection study, the following technologies were analyzed, at a Conceptual Engineering level: the Oxy-fuel Burner Reverb, the Teniente Converter, the CONTOP Cyclone Smelting Reactor, and further, the Ausmelt Furnace, the engineering of which was provided by the proprietary firm. The engineering of the other processes was developed by INDEC, which also integrated the comparative analysis of the four options. The analysis of a comprehensive set of technical factors, including integrated smelter metallurgical models, together with the evaluations of economical features, led to the selection of the CONTOP Smelting Technology for the modernization of the Luanshya Smelter.

Jan 1, 1999

By Henrique Ventura Oliveira

Continuous casting is the most important process for solidification of steels. In this process, the fluid flow pattern in the tundish and in the mould have significant effect on the product quality. Problems associated to fluid flow in the tundish include surface turbulence, ?short-circuits?, formation of dead zones and vortexing. During grade changes, mixing in the tundish plays a significant role in determining the length of the intermixed slab. All these flow aspects can be studied by means of mathematical and physical models. In the last years, numerical simulation of fluid flow has become a very popular tool in the analysis of the performance of continuous casting tundishes. In setting-up these numerical simulations, special care should be taken in choosing the appropriate mesh distribution, the interpolation scheme, the adequate location of the inlet boundary and the turbulence model. In the present paper, turbulent fluid flow in different configurations of tundishes was simulated. Different turbulence models were used in the simulations. Residence time distribution (RTD) and mixing curves during grade changes were predicted and compared to results obtained in physical models. The performances of the different turbulence models were evaluated. For the tundishes that have been studied, the performances of the different turbulence models tested in the present work were similar. There is no evidence that any of the models provided sustained improvement when compared to the well-established standard k- model. All turbulence models tested presented limitations in simulating flows under low turbulent Reynolds numbers.

Jan 1, 2006

By Aichun Zhao, Rui Wang, Yihong Li, Yanping Bao, Yafeng Ji, Jiansheng Liu, Xiao Hu, Qingxue Huang

The slag entrapment under different conditions of 80t blowing argon ladle furnace was investigated by physical simulation. The water was used to simulate liquid steel and liquid paraffin was for slag. The processing of slag entrapment under different blowing structures was analyzed and the critical velocity and critical droplets diameter of describing it was obtained. Based on the experiments, the relationship between the interface flow velocity and the critical blowing rate CBR was deduced. In the real process, it is suggested that the bottom blowing rate is from 40 L/min to 180L/min when the interface tension is 0.12~1.2 N/m during the soft argon blowing.

Jan 1, 2016

By Kikuo Okuyama, I. Wuled Lenggoro, Manabu Shimada

"Aerosol processing of materials such as (i) gas-to-particle conversion process (e.g., Chemical Vapor Deposition (CVD) method) and (ii) liquid (or droplet)-to-particle conversion process (e.g., spray pyrolysis) has become of major interest to produce novel submicron- or nanometer-sized particulate material used in electronic and chemical industries. After reviewing recent theoretical and experimental researches on the evaluation of properties and morphology of fine particles by the CVD and spray pyrolysis methods, the importance of the process engineering approach· for aerosol processing of materials and the use of advanced aerosol measurement technology have been pointed out.IntroductionMaterial synthesis via aerosol processing offers a route to producing nanometer-sized and submicrometer-sized particles of high purity with specifically tailored chemical and physical properties. Especially, single nanometer-sized particles (nanoparticle materials) are considered to play an important role in the synthesis of nanostructured materials as well as in nanotechnology in 21st century due to their quantum effect and so on.However, the transformation of gaseous or liquid precursors to the final functional particulate matters consists of various complex chemical and physical processes. In order to control the size distribution and morphology of produced particles, it is important to analyze and model various phenomena, such as gas-phase or liquid-phase chemical reaction, nucleation, condensation, agglomeration and sintering that occur simultaneously in aerosol material processing. By introducing the Aerosol Science and Materials Science, the authors have been trying to model the changes in particle properties and morphology by gas-to-particle conversion and droplet-to-particle conversion processes. The authors have also been trying to obtain the experimental data on the particles properties as accurate as possible."

Jan 1, 2000

By Matthew Jeffrey

Leaching, cementation, electroplating and flotation are all electrochemical phenomenon. They are also key processes in the hydrometallurgical treatment of metals. Unfortunately electrochemical methods tend to be under-utilized when studying these processes and one possible reason for this is the confusion surrounding the large number of electrochemical techniques available. In this paper four former PhD students of Professor Ian Ritchie present an insight into how one electrochemical technique can be used to compliment rate/kinetic studies. The paper details how to perform the experiments, interpret data, and recognize complications with the results. Examples where this approach has been highly successful are presented, and include: cementation of zinc by aluminium, cementation of copper by nickel, cyanide leaching of gold and the cementation of gold thiourea by mild steel. The examples illustrate that this universal approach adopted by Ian Ritchie provides the key to understanding the mechanism of many hydrometallurgical reactions.

Jan 1, 2003

By Yong Xian, Zhaohui Sun, Honggang Zhong, Qijie Zhai, Jie Sun

Vacuum refining is admitted as an effective means to remove impurities in the process of alloy smelting. In this paper, Orthogonal and single factor experiments were carried out to investigate effects of multiple factors, such as superheat degree of the melt, degassing time and vacuum degree, on the vacuum refining process. The results showed that the best removal rate of oxygen and nitrogen is up to 82.71% and 61.3%, respectively, due to high vacuum degassing efficiency. It is found that the superheat degree is minimal impact on the deoxidization rate, in addition, nitrogen removal is controlled by the degassing time. The inclusions exist in the AlV55 alloy are mainly composed of oxides and vanadium-nitrogen compounds.

Jan 1, 2015

Novel techniques were developed to obtain samples from and make measurements in the shaft of the flash furnace at the Kalgoorlie Nickel Smelter. The data obtained was used to validate mathematical models of the burners and the reaction shaft. Particle, gas and wall temperatures were measured along with the oxygen potential of the molten particles. Collected particles were characterised by sizing, chemical analysis and optical microscopy. The region of the shaft immediately beneath the burner where the rate of change was most rapid received special attention.

Jan 1, 1993

By Karel Verscheure

Hydrometallurgical zinc leach residue, EAF dust and other Zn-bearing by-products pose potentially serious environmental problems that threaten the sustainability of the operations. A pyrometallurgical process designed for treatment of such residues is the high-temperature submerged plasma Zn-fuming process. The successful operation of this process requires high Zn fuming rates whilst retaining vessel integrity through stable freeze-lining. A Zn-fuming model has been developed and used to systematically investigate a range of operating scenarios and to identify potential fluxing parameters such as CaO/SiO2, Fe/SiO2, MgO/feed-ratios in the input and fluxing additions of dolomite for maximum fuming rates and stable freeze-lining.

Jan 1, 2006

The entrainment of copper matte in the slag during the slag skimming stage of a Peirce-Smith converter was studied with a dam break model. Experiments were carried out with a range of fluid pairs where the lighter fluid was allowed to overflow a weir and the amount of entrained heavier fluid measured. The resulting entrainment is measured as the ratio of the heavy to light fluid withdrawn. The fluids include oil-water, water- glycerol and salt solutions-water pairs to cover a wide range of densities and viscosities. It was found that the Richardson number, Ri, correlates the entrainment well. For the case of the liquid-liquid interface initially at the same height as the weir, the entrainment was found to vary with Ri-1/3. The transient flow was simulated with a volume of fluid (VOF) code written in-house and used a stairstep approach to represent flow obstacles. The code was validated against the experimental results with good agreement for the variation of the heights of the two fluid with time. The simulation showed that the prevailing mechanism for entrainment is due to a pressure differential created across the liquid in the converter during pouring resulting in the heavier liquid being rotated upwards and over the weir.

Jan 1, 1999

By Sacha Neven

Submerged lance technologies combine high intensity processing characterized by rapid mixing and reaction rates using a simple reactor design. The Isasmelt technology uses a central submerged lance to inject oxygen-enriched air and fuel into a bath thus creating large gas bubbles and intensive turbulence and splash. The lance is equipped with swirlers to increase gas velocity and heat transfer. This enables the formation of a frozen slag layer on the lance which protects it from the aggressive environment. Water models as well as high temperature reactors were used to validate the Davidson-Schiiler model on bubbling. Frequencies and pressure amplitudes were measured in a wide range of gas flow rates: from m3/sec using a water model to more than 30 m3/sec in an industrial process. Agreement with the model was satisfactory. The experiments however also clearly showed that cross-flow and bubble wake induce slightly higher frequencies. No influence of the use of swirlers on the bubbling frequency was observed in the water models.

Jan 1, 2002

By A. Filzwieser

The highest current density suitable for the electrowinning process is between 50 to 60 % of its limiting current density. One of the most important influences on the limiting current density is the thickness of the hydrodynamic boundary layer near the electrode surface. Therefore, the fluid flow in a copper electrowinning cell is calculated. The numerical simulation - using the CFD-software package FIRE® - considers all three different types of the fluid flow, namely, the natural convection, the forced convection by electrolyte circulation and the forced convection by electrochemically induced gas stirring. The simulation of natural convection is based on the different density values in the boundary layer at the electrode surface given by a density/concentration correlation. The copper concentration - linked with the current density by Faraday law - is solved by an additional transport equation. The simulation of the forced convection by the electrochemically-induced gas stirring is done by using a real two-phase calculation. That means that all differential equations are solved again for the second phase. The numerical solution of the fluid flow field is compared with the results of LDA- measurements, which were done in a special cell. The software for the LDA enabled a calculation of the void fraction possible and therefore a rough estimate of the mass transfer coefficient through the prevailing gas bubble induced convection can be made by assuming the influence of relative bubble volume.

Jan 1, 1999

By Paulo von Krüger

This paper deals with the cell design and operation of a tin electrorefining 1:5 pilot plant. The purpose of the work was the fitting of the basic parameters to be used in a full-scale tankhouse from a major Brazilian tin producer. The main specific difference was the use of permanent stainless steel cathodes instead of conventional tin starting sheets. The results of both product quality and operating parameters are discussed.

Jan 1, 2003

By Bernhard J. Ralph

In refractory gold ores much of the gold occurs in sub-microscopic form in sulfide minerals, most commonly pyrite and arsenopyrite Bacterial leaching is being developed as a pretreatment for these minerals to aid the liberation of gold and a variety of extracting reagents. This paper reviews the nature of the principal micro-organisms involved, the effects of various physico-chemical factors on the rate and extent of extraction, and likely mechanisms involved.

Jan 1, 1989

Silver has the highest electrical conductivity of all metals and consequently this property is an attractive feature which makes it a leading candidate for use in electronic devices. The research conducted was focused primarily on the development of a process for obtaining a deposited silver-coating onto alumina, for applications related to electrical-conducting devices and, ancillarily, catalysts. Alumina balls and plane substrates were utilized for the investigation. The coating process employed an aqueous arnmoniacal silver-nitrate electrolytes with a formaldehyde solution as the reductant. Modifying additives - an activator which would be expected to promote good deposition-characteristics onto the (dielectric) substrate and an inhibitor which would obviate homogeneous reduction (precipitation) of silver was observed when the activator-containing silver-electrolyte reductant constituents were combined. However, the silver-electrolyte/reductant system with inhibitor could be employed (at 80°C) to achieve a viable (subject to future research optimization) coating on alumina. The influence of the processing temperature on the deposition process was delineated during the course of the research. The morphology of the deposited-silver on the alumina balls was assessed by SEM imaging. A tape-peel test was employed, with the plane substrates, to semi-quantitatively characterize the adhesion to the alumina.

Jan 1, 1998

By Jacob Bummer, Greg Roset, Dayle Flynn

"IntroductionStillwater Mining Company operates a Precious Metals Smelter (PMS) located in Columbus, Montana USA. The PMS processes iron, copper, and nickel sulfide bearing concentrates containing platinum, palladium, gold, and rhodium. The concentrates are produced from two mines in the Beartooth Mountains located in south central Montana. The PMS utilizes a 7.5 megawatt 3-in line electric furnace to smelt the concentrates, and two Top Blown Rotary Converters (TBRC's) to remove iron. In addition to the mine concentrates, the PMS also processes various forms of Platinum Group Metal (PGM) bearing recycled catalyst. The sulfide matte produced within the electric furnace and TBRC's acts as a collector for the PGMs. Throughout the operation of the PMS, there are three different forms of molten material that are processed through the Stillwater Granulation system: TBRC matte, TBRC slag, and electric furnace matte. This paper describes the operation of this granulation system.Tapping the FurnaceWhen a sufficient level of molten PGM bearing matte has been reached within the inner volume of the electric furnace, the molten material is ""Tapped"". Tapping requires drilling into the electric furnace until reaching the molten matte phase. The matte phase will drain out of the drilled hole through a graphite launder into a 5 ton refractory lined ladle. Once the ladle is full, the tap is plugged with a mud gun."

Jan 1, 2012

By Patrick F. Mahoney

Each year in the United States over 10 million tons of metal are discarded with our municipal waste. This, includes, not only ferrous metals, aluminum and copper but gold, silver, platinum and every other precious metal. Resource recovery, as an approach to waste management, is replacing disposal and it presents great opportunities for those in the metal refining and recovery industry. Combustion of waste enriches the metal fraction left in the ash to the point where metals can be efficiently recovered. The recovery and quality of metals can be enhanced by good combustion control. Innovative technology is needed to efficiently tap this generous, and renewable mine.

Jan 1, 1995

By Junji Shibata

As one of the effective usages of various wastes discharged in non-ferrous metal industry, the synthesis of hydrotalcite was carried out using aluminum dross as a raw material. Hydrotalcite is one of the inorganic anion exchangers and has layered structure of complex hydroxide. The removal of toxic metal ions such as As(III), As(V), Cr(VI) and Se(IV) with the hydrotalcite was investigated, and the removal properties were compared from the viewpoint of the anion exchange amount and exchange rate. Hydrotalcite can be obtained by a co-precipitation method from the aluminum dross and the waste MgCl2 solution discharged in an aluminum regeneration process. Slight amounts of SiO2, Al2O3, Fe2O3 and so on remain in the reaction product as an impurity component. Interlayer distance of the obtained hydrotalcite is about 0.3nm. Hydrotalcite changes to Mg-Al oxide by the calcination at 773K for 3h, and then hydrotalcite is formed again by a rehydration operation after calcination. The toxic metal ions are removed from aqueous solution by the anion exchange reaction in the pH region where toxic metal ions exist as the anionic species like AsO2-, HAsO42-,CrO42-, and SeO32-. The exchange amount is considerably concerned with the valence of anionic species and the size of anionic species. The removal of toxic metal ions were investigated from the engineering aspects such as the low concentration limit to be removed, the amount of hydrotalcite to be used for the perfect removal of toxic metal ions and so on.

Jan 1, 2006

By Pekka Taskine

In the Kokkola zinc smelter, as in most other zinc roasting plants, there is now a trend towards using concentrates with an increasing impurity content. This also often means that the size distribution of the concentrates gets finer. Iron is present in sulfidic zinc concentrates with the highest percentage as a single impurity. The behavior of iron in zinc roasting was studied in laboratory experiments. Commercial zinc concentrates with a low and high (1.5 - 16 wt-%) iron content as pyrite or in the sphalerite lattice were oxidized to various degrees to establish the reaction mechanisms of iron in roasting. Microscopy studies were carried out on the calcine, and the findings were presented in numerous photographs of the polished cross sections. SEM/EDS techniques were used for analyzing the phases and particle morphologies present in the samples. An oxidation mechanism of zinc concentrates with a high iron content was suggested.

Jan 1, 2002

By Lztok Peruš, Goran Kugler, Matevz Fazarinc, Milan Tercel

"Hot deformability of M42 tool steel additionally alloyed with cobalt and molybdenum was investigated. Hot-compression tests were carried out in the temperature range 850 °C -1200 °C, at strain rates range 0.001--6s-l up to strain of0.9. Field-emission scanning electron microscope and optical microscopy were used for characterization of microstructure of deformed samples, which revealed a very complex precipitation of carbides that strongly depends on the soaking temperature, the soaking time, the stress state, the deformation temperature as well as on the strain rate. Gathered data was used to calculate the processing parameters such as process maps, apparent activation energies and strain hardening exponents. For better understanding of thermodynamical properties of the studied steel a simultaneous thermal analysis was conducted. Furthermore the analysis of phase equilibrium was calculated using Thermo-Cale software. On the basis of these studies the optimal soaking temperature and process windows were determined.IntroductionHot workability ofledeburitic tool steels is important economic factor. This means that for each tool steel individuallysafe range of hot working parameters should be revealed. Publications in the literature with regard to the hot workability of tool steels are rare and therefore more information from this research area is desired.The relatively low hot workability of ledeburitic tool steels, i.e. steels in which the solidification is completed by a eutectic transformation of the residual interdendritic liquid to austenite and various alloy carbides (ledeburitic carbides), is usually characterized by the production of surface and internal cracks during the hot deformation."

Jan 1, 2013

By Alireza Zakeri

To evaluate the behavior of minor elements in the copper smelting process, activities of silver, selenium and tellurium at minor concentration were determined at 1473 K within the miscibility gap of the Cu-S-Me (Me = Ag, Se, Te) and Cu-Fe-S-Me systems varied in Fe/Cu ratio. Phase relations between the immiscible metal and matte phases in the foregoing systems were first established by a quenching technique at 1473 K to supplement the activity measurement data. A Knudsen-effusion mass spectrometer, capable of handling complex gaseous systems and relatively small vapor pressures, was adopted for activity determination. Using a multiple Knudsen-cell, the ion intensity of minor element in the sample under study was measured simultaneously with that in a reference sample. Activity was obtained from the ratio between the measured ion intensities as well as the known activity value of the minor element in the reference sample. Limiting activity coefficients of the minor elements were correlated with composition of the matte. Based on the experimental results, the vaporization behavior of the minor elements has been discussed.

Jan 1, 1999