Search Documents

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached 'biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991

By William A. Hockings

This report describes the results of laboratory studies on leaching of copper ores.tlf These studies are the first step of a program for the investigation of in situ leaching of tabular, metalliferous ore bodies.(2) The basic steps required in the development of an in situ process are: 1. Leachability - the ability to dissolve the metal values from the ore under in situ conditions must be demonstrated. 2. Ore Preparation - the ore must be prepared so that sufficient contact with the solution can be attained. 3. System Design - integrated in situ systems must be designed and studied for engineering feasibility. 4. Economic Feasibility - the economics of the system must be shown to be economically feasible and competitive. 5. Environmental Feasibility - the loss of reagents into the environment must be investigated. 6. Pilot Scale Testing - the feasibility of the system must be demonstrated on a sufficiently large scale. The studies described in this report were concerned only with the first step of the program, viz., leachability. Native and sulfide copper ores from the Michigan copper district were selected as model ores for these studies. Aqueous amnonia solutions were chosen as the solvents to be investigated. In this study carbonate (CO3, HCO3, H2CO3) was used exclusively as the anion. In keeping with custom it is referred to as carbon dioxide and concentrations are ex- pressed in terms of CO2. When leaching native copper the reaction is

Jan 1, 1976

By Moto Goto

Onahama Smelter of Onahama Smelting & Refining Co., Ltd. has two green- charge reverberatory furnaces; the old furnace was constructed in 1965 and the new one in 1973. This paper discusses the use of oxygen-oil burners in a green-charge reverberatory furnace and also compares the copper loss in slag between the two furnaces at Onahama Smelter. During the past ten years of operation, no shutdowns of the old furnace were necessary and the smelting capacity was increased by 25% by the use of two oxygen-oil burners. These burners are suitable for a green-charge reverberatory furnace to in- crease the smelting capacity without causing an increase of the exhaust gas volume and refractory erosion. After two years of operation of the old furnace, a bottom build-up in the charging zone of approximately 50 centimeters was experienced, and this build-up has stayed at this level since then. In 1973, a new additional reverberatory furnace was put into operation. Copper content in slag of the new furnace was lower by approximately 0.15% than that of the old one during the first several months after the start-up. Investigations were then made on the effect of the bottom conditions in the charging zone on the copper content in slag.

Jan 1, 1976

By cheng Peng-fei, TANG Hai-yan, guo Xiao-chen, LI Jing-she, Liang Yong-cang, Zhao Baojun

The origin and evolution of non-metallic inclusions for Al-killed casing steel during EAF-LFVD- CC process were studied by industrial tracer experiments. The formations of Al2O3 and MgO·Al2O3 micro- and macro-inclusions from ladle slag were analyzed by theoretical calculations. The results show that micro-inclusions were formed during deoxidation and temperature decreasing in the process of casting, most of the macro-inclusions come from entrapped ladle and mold slags. In addition, most of the Al2O3 formed were modified into 12CaO·7Al2O3 and 3CaO·Al2O3 inclusions which are liquid at steelmaking temperature. MnS cannot be fully modified to CaS and it was only wrapped outside the alumina or calcium aluminate in the form of (Ca,Mn)S with the amount of Ca-Si wire fed during the test.

Jan 1, 2016

By B. Q. Li, R. A. Mirshams

"A numerical algorithm is described for the simultaneous prediction of the thermomechanical behavior of the materials and microstructure evolption during metal forging. The numerical development is based on the finite element solution of the thermoviscoplastic deformation of metals coupled with the internal state variable model describing the microstructure evolution involving work hardening, recovery, recrystallization and grain size distribution. The finite element code for rigid viscoplastic deformation is developed based on the modification of the existing code for the thermal and fluid flow calculations. The code is tested against and compares well with the results reported in literature. The procedures for the integration of the · rnicrostructure model into the macro finite element model are described. Results are presented showing the characteristics of materials dynamics and mechanical deformation during simple metal forging processes.IntroductionIn industrial deformation processes such as hot rolling and forging, the workpiece undergoes both macroscopic plastic deformations and microstructural evolution. A computer model that allows to predict both materials dynamics and macroscopic deformation is obviously more useful for both fundamental understanding and deformation process optimization. For some industrial applications, especially those involving novel, light and high strength materials, such an integrated model is critical in that both materials and thermomechanical 'behavior during forging must be carefully controlled to obtain the products that meet the desired strength requirement [I]."

Jan 1, 2000

By Ramana. G. Reddy, Haoxing Yang

The electrodeposition of zinc from zinc oxide using urea and choline chloride mixture in a molar ratio 2:1 is investigated in different experimental variables, namely, the concentration of added [BMIM]HSO4, temperature, and applied cell voltage. The additive, [BMIM]HSO4, was determined to have beneficial effect on the current efficiency, energy consumed in the process and surface morphology of the deposits. The highest current efficiency (92.6%) and lowest energy consumption (2.92kWh/kg) was obtained for solution with 20mg/mL [BMIM]HSO4. The morphology showed the formation of absorbed additive layer on the cathode at higher concentration of additives. Experiments were conducted at different temperatures between 343K and 388K and at various applied cell voltages between 2.7V to 3.6V to determine the best experimental conditions. By varying temperature, highest current efficiency (91.3%) and lowest energy consumption (2.69 kWh/kg) was obtained at 373K. The electrodeposition process is enhanced between the applied voltage 3.0-3.3V by achieving lower energy consumption (2.75~3.06kWh/kg) and higher current efficiency (88.4~89.7%). SEM images showed grain size is significantly increased in higher applied voltages. While at higher temperatures, it seemed to generate particle growth as clusters at the outer deposit layer.

Jan 1, 2014

By Zhigan Deng

Cooling crystallization was used to separate iron (III) and nickel (II) from acidic sulfate solution produced by leaching of molybdenum-nickel black shale. The effect of K2SO4 concentration, crystallization temperature, solution pH and crystallization time on recovery of nickel (II) and precipitation of iron (III) was investigated, in order to obtain effective separation of nickel and iron. The optimum parameters determined were as follows: 200 g/L K2SO4, 10 °C crystallization temperature, solution pH of 0.5 and 24 h crystallization. Under these conditions, 97.6% nickel (II) was recovered as K2Ni(SO4)2, 6H2O crystals and only 2.0% of the total iron (III) was precipitated. Recrystallization yielded K2Ni(SO4)2, 6H2O crystals with a purity of 98.4%.

By Nourreddine Menad

Plastic materials have been associated with electric and electronic applications since the early days of the electrical industry. Plastics can amount to 30 percents of the scrap mass. Generally, they are treated with flame retardants such as halogenated ones and they can result in different toxic chemical compounds. These plastics can be used as combustibles in the recovery of copper and precious metals. However, during their combustion, halogenated flame retardants can produce dibenzo-p-dioxins and dibenzo-furans. The estimated thermodynamic data of several organic compounds resulting from combustion of electric and electronic scrap, have been used in conjunction with the program HSC to calculate the conditions for dioxin and furan formation. The results show that the formation of the dioxins is dependent on the quantities of carbon, hydrogen, chlorine and oxygen reacting in a given system, as well as on parameters such as temperature and pressure.

Jan 1, 1998

By M. Krishna, Jayagopal Uchi1, Shanta Sastry, B. M. Satish

"A well-considered composite of ZA-27 reinforced with weight percentage 0, 2, 4, and 6% of alwninite particulate has been made by compocasting technique. The elastic properties of ZA- 27 /alwniniute particulate composite were determined by using U1M. The results showed that the modulus of elasticity and UTS of the composite gradually increases with increase in the wt.% of reinforcement. However, the overall ductility decreased monotonically with an increase in reinforcement. The results of these tests· as well as the predictions of several model~ for composite strengthening available in the literature were compared with experimental results. The data observed from Young's modulus by measurements studies were compared with theoretical results predicted by Eshelby model.IntroductionMetal matrix composites (MMCs) have received increasing attention in _the recent decades as engineering materials. The introduction of a ceramic reinforcement into a metal matrix produces a composite material resulting in an attractive combination of physical and mechanical properties that cannot be obtained with monolithic alloys. Particulate reinf9rced MMCs among the discontinuously reinforced MMCs have attracted quite a lot of attention both in the industrial sectors and the academic communities. There is an increasing need for knowledge about the processing techniques and mechanical behavior of particulate MMCs in view of their production getting enhanced and their commercial applications becoming wider [I]. Interest in particulate reinforced MMCs is mainly due to easy availability of particles and economical processing techniqu"

Jan 1, 2000

By John W. Graydon

Incineration is an attractive alternative to the disposal of MSW in landfill sites. However, the process of incineration generates fly ash which contains significant levels of leachable heavy metals - particularly cadmium, lead, and zinc - and it is essential to manage this fly ash in an environmentally sound manner. The compositions, phases, textures, morphologies and size of fly ash particles have been studied by light microscopy, scanning electron microscopy, X-ray microanalysis, and X-ray diffraction. The detailed spatial relationships and speciation of the environmentally significant constituents have received particular emphasis. The information obtained is useful in understanding how fly ash is formed during incineration, in understanding the leaching behavior of untreated fly ash if it is disposed of in a landfill and, most importantly, in guiding the development of the best treatment strategies for fly asti to mitigate its environmental impact.

Jan 1, 1992

Proposed by outstanding electrochemist and electrometallurgist Prof. Raphael Agladze (191 1- 1989), process of copper and manganese co-electrowinning was enhanced to the pre- electrowinning stages: low,temperature co-leaching of copper and manganese containing materials, and to high-temperature co-roasting of the same materials with consecutive leaching. The report presents results of experimental investigations of the processes mentioned above, as well as results of thermodynamic investigations of co-roasting processes, and co- leaching processes computer modeling.

Jan 1, 1997

By J. K. S. Tee

Using a novel method, zinc has been selectively removed from galvanized steel scrap on a laboratory scale. The separation is based on thermodynamic principles: during chlorination in air-chlorine (10:l) mixtures at 800 OC, zinc forms a volatile product (zinc chloride) while iron does not chlorinate as its oxides are more stable than the respective chlorides. As much as 92 % of zinc is removed from the surface of steel within 10 minutes. This process overcomes tedious and costly preparatory stages associated with leaching - electrowinning methods.

Jan 1, 1999

By Fumio Hashiuchi, Yushiro Hirai, Masatoshi Maeda, Toshihiro Nagata

"Increase in the copper smelting capacity at Saganoseki Smelter & Refinery was attained through various improvements in the PSconverters and the flash furnace. Two of the major innovations in the converting process were: a new operational technology which avoids increase in the copper content in the converter slag even when higher copper grade matte (65%) are treated in the slag making stage and a technology which shortens the operational interruption time which is caused by coolant charging. The latter was realized by introducing a new automated coolant charging system with which it was made possible to charge the coolant without stopping the blowing into the converter. These improvements brought about a remarkable increase in · the production capacity per converter and an annual production of 450,000 tons of copper without adding new furnaces was made possible. In addition, good results have been obtained of the tests with modified tuyeres to further increase the production.IntroductionIn a bid to renovate its Saganoseki Smelter & Refinery and to establish a leading production unit in terms of global competitiveness, Nippon Mining & Metals undertook major restructuring efforts since 1994. One of its themes was the shift from· a two-flash furnaces operation to a single-flash furnace operation. The shift was successfully completed in 1996 while maintaining the production at the same level (330,000 tons per annum of copper). Then, the productivity was enhanced to 450,000 mtpy without adding new furnaces through technological and operational improvements. It is now planned to increase the smelting capacity further to 470,000 mtpy this year.Some technological and operational improvements in the matte converting process and the new plan resulted from the tests with modified tuyeres are presented in this paper."

Jan 1, 2000

By E. C. T. Chao

Micro-optical and synchrotron radiation-induced X-ray fluorescence (SXRF) techniques have been used to study unoxidized and oxidized samples of Carlintype sedimentar,y rock-hosted disseminated gold ore. In these samples, Where much of the gold is submicroscopic, the SXRF technique, which has a spatial resolution of about 20 ~m and a minimum detection limit (MDL) in the ppm range, is an ideal and necessary tool for precisely locating gold-rich areas in a sample. Gold-rich areas pinpointed by SXRF were later studied in detail by micro-optical methods, principally optical microscopy and scanning electron microscopy with energy-dispersive X-ray analysis (SEM-EDX). In two unoxidized and one oxidized ore samples, SXRF analyses have shown gold to be present predominantly in discrete clay-rich and silicified areas. Gold was not detected by SXRF in association with pyrite or carbonaceous materials. SEM-EDX examination of the gold-bearing areas in the unoxidized samples succeeded in identifying only two free gold particles, 0.2 and 0.5 ~m in size. In the oxidized sample, gold particles appear to be larger (but still submicroscopic) in average size and more evident in micro-optical examination after SXRF location of goldbearing areas. The findings of these studies may help to improve the efficiency of processing and recovery of gold from unoxidized ores.

Jan 1, 1987

By Wankun Wang, Shixing Wang, Jinhui Peng, Zebiao Zhang

"Germanium leaching from germanium dust and fume was carried out using sulphuric acid. Response surface methodology (RSM), based on a five level, four variable central composite design (CCD), was employed to obtain the best possible combination of liquid/solid ratio (Xi: 2-10), leaching time (X2: 1-5 h), sulphuric acid concentration (X3:3.15-15.75mol/L) and leaching temperature (X4:50-90 *C) for germanium leaching. The obtained experimental data were fit to a one-order polynomial equation using multiple regression analysis and also analyzed by analysis of variance (ANOVA). The 3-D response surface plot and the contour plot derived from the mathematical models were applied to determine the optimal conditions. The optimum extraction conditions were: liquid/solid ratio of 10, leaching time of 1 h, sulphuric acid concentration of 15.75 mol/L, and leaching temperature of 87.8 'C. Under these conditions, the germanium leaching extent was 65.14%, which is in close agreement with the value predicted by the model. The samples were characterized before and after leaching using X-ray diffraction (XRD).IntroductionResponse surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [1-15]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the vital controllable factors are identified. It is also used to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected [6], The process optimization of the sulphuric acid leaching of germanium from germanium dust and fume has not been reported in the literature. Hence the present work intends to assess the effects of variables such as liquid/solid ratio, leaching time, sulphuric acid concentration and leaching temperature and to identify the optimum conditions using RSM. The characteristics of sample before and after leaching are assessed using the advanced analytical instruments such as X-ray diffraction (XRD)."

Jan 1, 2012

By Boyd Davis, Vladimiros Papangelakis, Joshua LaMarre, Jan de Bakker

"HCl leaching using molten salt hydrates has the potential to improve the extraction of nickel from laterite ores. However, as in other HCl leaching applications, recovery of HCl is key to process economics. Spray pyrohydrolysis, which is used in current chloride-based flowsheets, is associated with a high energy cost. The authors have developed a proposed laterite leach circuit using an alternative HCl recovery route. The leach circuit envisions a leach by concentrated (33%) HCl in an MgCl2 molten salt hydrate (MSH) or brine medium, followed by Ni/Co recovery and iron precipitation. Magnesium and chloride are precipitated from solution as magnesium hydroxychloride; this hydroxychloride is thermally decomposed to produce HCl gas. The proposed flowsheet employs a chloride leach circuit with simpler equipment and lower energy cost than in the conventional practice of pyrohydrolysis. Laboratory work investigated key aspects of the flowsheet, including precipitation of magnesium hydroxychlorides and their composition; magnesium hydroxychloride thermal decomposition; and iron control.Introduction As sulphide nickel ores become harder to mine and more complex to process, laterite ores will increase in importance. Laterite ore deposits can be divided into two main mineralogies. Limonite ores consist mostly of hydrated iron oxide, FeOOH, with 1-3% nickel substituting for the iron. Saprolite ores consist of iron-magnesium silicates, (Fe, Mg)2Si04, again with some nickel substituting for the metal ions. Limonite ores can be treated using the HP AL (High Pressure Acid Leach) process, in which the ore is reacted with sulphuric acid at high temperature in an autoclave. HP AL, however, cannot in general be used to treat saprolite ores because the magnesium enters solution and consumes sulphuric acid, which results in excessive spending on lixiviant. It is therefore desirable to find a hydrometallurgical process specifically for saprolite ores that can provide better results than the treatment options currently available."

Jan 1, 2011

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By Ahmet Haxhiaj, Jaroslaw Drelich

"Both composition and porosity of pellets are the main parameters influencing the reductive melting process in water-jacket furnace during the roasting of sulfide lead concentrate. Roasting in a smelter located in Trepçë is done at about 9000C, for pellets which are composed of PbS, CaCO3, Fe2O3, and SiO2. In order to faciltiate the formation of slag in the reductive melting, the pellets must have the proper content of CaO, SiO2, and FeO, and porosity. The plant’s practice indicates that pellets with porosity of 18% do not melt adequately in the water-jacket furnace. The optimum porosity for the proper melting of pellets needs to be 32-40% and can be achieved when pellets are loaded with more than 10 wt.% CaO. Pellets with less than 10% CaO have a limited network of pores, such that reactive gases cannot reach the entire ore structure. Also, the composition of the pellets must satisfy the ratio of CaO : SiO2 : FeO = 1 : 1.2 : 1.8 to facilitate the formation of slag in the reductive melting process.IntroductionAgglomeration roasting of sulfide lead concentrate is an important phase in the production of lead by reductive melting [1-6]. The reductive melting process is a complex process with contradictory effects of several technological indexes which many times are hard to measure and determine. In this process, loading the water-jacket furnace with pellets of optimized composition and structure can reduce the consumption of coke, and achieve high level of lead recovery. Pellets (agglomerates) should be porous, but at the same time they should have necessary mechanical strength. ‘Self-melting’ ability of pellets is controlled by the types and quantities of fluxes blended into the pellet composition. Three major additives and their role are:"

Jan 1, 2011

By Byung-Su Kim

The recovery of elemental sulfur from sulfur dioxide has important implications for coal- burning power plants and nonferrous metal smelters. The thermodynamic analyses showed calcium sulfide to be suitable for recovering elemental sulfur from sulfur dioxide. At the temperatures of 1023 to 1153 K under the sulfur dioxide partial pressures of 5.0 - 60.1 kPa, elemental sulfur from sulfur dioxide was recovered by its reaction with calcium sulfide. The kinetics of this reaction were measured at the same conditions using a thermogravimetric analysis technique. This reaction scheme would be attractive if the coproduct calcium sulfate can be reduced to regenerate calcium sulfide. This is the topic of another paper. At 1073 K under the sulfur dioxide partial pressure of 25.8 kPa, 48 % of the original calcium sulfide was converted to calcium sulfate in an hour. Under the same conditions, 55 % of the regenerated calcium sulfide were converted to calcium sulfate in an hour even after third regeneration.

Jan 1, 1999