Search Documents

By Floyd C. Bossard

A method of hand-calculating the air-cooling requirements of a conceptualized underground mining operation is presented for the reader's orientation. Separate air heat load calculations were conducted for adiabatic compression, electromechanical equipment, wallrock, broken rock, groundwater, and blasting operations. The air heat sources were calculated for four mining levels under conditions representative of a typical planned mining operation at depth. The total heat gain on each level will approximate the level air-cooling requirements. The results of these hand calculations can be further modified by the use of mine ventilation computer software that refine the heat-source calculations, predict underground ambient air temperatures, and establish the air-cooling requirements of a mine. INTRODUCTION The principal mining method employed is a modified vertical crater retreat (VCR) blasthole operation. Typical scopes range from 20 to 40 feet wide, 75 to 100 feet long, and 100 feet in height. Six and one-half inch blastholes are drilled with an "in the hole" hammer drill. Eight-foot high horizontal rounds are blasted down. Mucking of ore from the undercut to orepass is done with LHD equipment operated from a remote control station. Backfill includes hydraulically placed tailings with cement, and waste rock when available. Stope access is from ramp sub-levels on 50-foot vertical intervals. Crosscuts are ramped down to the first stope cut 25 feet below the sub-level elevation. Then the crosscuts are raised by taking down the back when each stope cut is completed, until an elevation 25 feet above the sub-level is reached. The crosscuts are filled with tailings, and/or waste rock. See Figure 1. Typically, a two-pronged approach to defining the air-cooling requirements is conducted. First, the principal sources that make up the air heat load are individually hand-calculated. Second, projections of mine heat load are calculated by utilizing computer modeling techniques. This paper discusses the first method (hand calculations) of determining the individual components of heat flow into the mine. CALCULATED AIR HEAT LOADS Adiabatic Compression The plans for the mine include delivery of 300,000 cfm of air to ventilate the lower level operation. This is equivalent to approximately 200 cfm/ton of rock produced (300,000 cfm/1500 tpd of ore and waste). As air flows down a shaft, with no heat interchange between the shaft and air and no evaporation of moisture taking place, the air is heated in the same way as if it were compressed in a compressor. Dry air increases in temperature about 5.4°F per 1000 feet. One BTU is added to each pound of air for every 778 feet of decrease in elevation, or is subtracted for the same elevation increase. For dry air, the dry-bulb temperature change is 1/(0.24 x 778) = 0.00535°F/ft., or 1°F/187 ft. elevation. Auto-compression may be masked by the presence of other heating or cooling sources, such as shaft wallrock, groundwater, air and water lines, electrical facilities, etc. The major factors influencing the temperature of the air delivered underground by a shaft are (1) the night time cool air temperature's effect on the rock or lining of the shaft, (2) temperature gradient of ground rock related to depth, and (3) evaporation of moisture within the shaft which increases the latent temperature and decreases the sensible temperature. [Calculation For Adiabatic Heat of Compression] a. Assumptions: 1. Three hundred thousand cfm of fresh air at 3000 level has increased in temperature during the summertime to the point where it has little available cooling power. Air-cooling will be required on 3000 Level and below. 2. Elevation of 3000 Level is approximately +1000 ft. above sea level.

Jan 1, 1993

By Robert B. Fulton

The objective of this chapter is to discuss the interrelationship between industrial minerals and chemical manufacturing. It is intended to supplement rather than duplicate the commodity chapters. Particular emphasis is given to the pertinent chemical element and to market factors. Condensing this broad subject into a few pages of this handbook permits treating only the most important elements derived from industrial minerals. Hydrocarbons, which quantitatively dominate as raw materials for the chemical industry, are omitted, as are the metallic elements and the minerals covered in other "use" chapters such as phosphorous, potassium, and nitrogen for fertilizers, and titanium dioxide for pigments. The remaining six elements of major importance are: boron, bromine, chlorine, fluorine, sodium, and sulfur. These elements are treated individually under separate headings. [Table 1] affords an overview of the main industrial minerals, the chemical products derived from them, and end uses of the products. Salt brines have particular importance as raw material sources for the chemical industry. Table 2 is a chart of the chemical compounds derived from four types of brines: (1) Owens Lake-type brines, which are sources of boron and sodium compounds; (2) Midland-type brines, from which bromine, iodine, and chlorides of calcium, magnesium, potassium, and sodium are derived; (3) Searles Lake-type brines, yielding boron, bromine, lithium, magnesium, potassium, and sodium compounds; and (4) Silver Peak- type brines, produced mainly for lithium. MARKET ATTRIBUTES Some of the important market traits common to industrial minerals used by the chemical industry are: 1. They are international commodities, such as fluorspar and sulfur, which largely move to foreign consumers. 2. Grade, and freedom from deleterious elements are important factors affecting their usability in chemical processes. An example is salt (NaCl) used in electrolysis where ultrapure evaporated salt is required to meet rigid specifications. 3. Purified products take on the characteristics of specialty items and command a distinctly higher price than the basic commodity from which they are derived. 4. In practically all cases, chemical users require some sort of cleaning or beneficiation of the naturally-occurring mineral to bring it to specification, and individual specifications may vary from user to user for essentially the same use. 5. In some instances it is necessary to strike a balance between what the vendor can supply and what the buyer requires, with the result that specifications have to be eased to afford the needed materials in marginal cases. 6. Because they tend to be bulk commodities, low cost for handling and transportation are important and such costs may limit the area from which a chemical user can draw his supply. 7. Shipments are usually in bulk and frequently in multiple-car, full-trainload or full-shipload lots to reduce transport costs, which in turn may require large terminal investment facilities. 8. Purchases are generally by contract of one year or longer term, with spot buying playing only a minor role. 9. Contract prices are usually fixed in short term commitments, but may vary according to assay, with premiums and penalties for content above or below the norm; however, general practice is for specifications to be fixed in the contract with minimums being set for the desired material and maximums for undesired elements. In longer term contracts, prices are often escalated on labor, fuel, and other vendor processing costs. 10. Suppliers of individual commodities to the chemical industry tend to be limited in number and are generally medium- to large-size producers that supply a few major consumers. 11. The bulk of the mineral volume is for basic chemical uses, sulfur suppliers to sulfuric acid producers and fluorspar for hydrofluoric acid producers being typical examples. These basic chemical products then are used for the production of other products. 12. Shortage of a supply of adequate quality leads consumers to seek substitutes. In the case of fluorspar, much work is being done on recovery of fluorine from phosphate rock. Success in the form of fluorosilicic acid and/or hydrofluoric acid production could, in time, affect the hydrofluoric acid chemical industry. 13. Markets tend to be characterized by cycles of shortage followed by oversupply, with attendant wide price fluctuations. 14. Baniers to trade can have an adverse effect on the necessary movement of industrial minerals used by the chemical industry in international trade. Antidumping laws, quotas, and tariffs can disrupt or dislocate normal markets. 15. Chemical industry consumers may back-integrate for security of supply or for favorable economics, sometimes by joint ownership and often with experienced mining partners.

Jan 1, 1994

By Paul G. Schmidt

The Crandon massive sulfide deposit Forest County, Wisconsin, was discovered by Exxon Minerals Company, U.S.A., in July 1975. Announced estimated in-place reserves are 62 M metric tons (70 million short tons), grading about 5% zinc and 1% copper. The reserves are evenly divided between massive sulfide are and stringer sulfide ore. The sulfide body is associated with Precambrian felsic pyroclastic rocks, and it is overlain by intermediate volcanic rocks and their derived sedimentary rocks. These rocks were subjected to greenschist facies metamorphism and were tilted to a near-vertical attitude. Geologic observations indicate a submarine-volcanic-exhalative origin for this deposit.

Jan 1, 1978

By Rex T. Ellington

The fluidized bed is an effective method for investigating retorting phenomena and possibly a commercial means of retorting oil shale. Both were examined by Sinclair Oil Corp. (now part of Atlantic Richfield Co.) in the period 1.965 to 1968. The results of the work show that presence of an oxidizing environment during retorting results in loss of oil yield which indicates that vapor phase oil burns in preference to combustion of coke on spent shale. This has implications for several types of retorts. Correlation of the results of this work with that of other investigators shows that the partial pressure of retorting products in contact with oil shale during retorting has an effect on yield. Consideration of hardware indicates that there are several possibilities for commercial embodiment. As a companion to shaft-type retorts the fluidized bed could have good potential. Realistic assessment of costs suggests that further development may have to await commercialization of another process. The existence of a plant in which to test prototype size would markedly reduce such development costs. Results Preliminary development work with the apparatus was carried out using a fluidized bed of sand, as explained later, with the entire system brought up to temperature and flows stabilized. The shale was injected rapidly in a slug (batch) which had small mass compared to that of the high temperature system to make the reaction approach isothermality with reasonable approximation of instantaneous preheating. Typically, the temperature in the center of the bed dropped from 900°F to 600°F one minute after batch addition. It returned to 750' within three minutes and 900° within seven minutes. Obviously, the bed was quenched but it recovered rapidly. Average bed temperatures of 700' to 1020°F were examined to compare the effect of temperature with published results. Yields In the 700°F range were only 10 to 15%, of Fischer Assay (FA). Above about 950'F, oil yields decreased and gas yields increased. Nitrogen was used first as the fluidizing gas to provide a chemically inert medium. Incept for an insignificant dip at 895"F, Figure 1, oil yield was not affected by retorting temperature in the 800° to 900' range as long as residence time was adequate (16 minutes). At 925°F, the oil yield was some 103% FA. With further increase in temperature, the yield decreased to 86% FA at 1015°F. There is no increase in carbon on spent shale, the lost oil goes to Increased gas make.

Jan 1, 1972

By John R. Duble

Through 1980, demand for cement in the Pacific Basin countries still seemed to exceed output. Availability of cement in the industrialized and developing countries of East Asia, Southeast Asia, and Australasia for the 1975 - 1980 period are discussed in this report. Quantitative data includes production, imports, exports, and apparent consumption. An account of new cement plants and plant extensions is provided. Countries and areas covered include: East Asia---Japan, South Korea, North Korea, Taiwan, China, Hong Kong, Philippines; South east Asia---Thailand, Vietnam, Singapore, Malaysia, Indonesia; Oceania (Australasia)---Australia, New Zealand, New Caledonia, Fiji.

Jan 1, 1982

By G. I. Voiloshnikov, V. E. Dementyev

Wide use of adsorption methods for metal recovery is one of the most important achievements of gold metallurgy of the last decades. Anion exchange resins or activated carbons may be used as adsorbents. This paper presents a brief overview of IRGIREDMET effotts on development, testing and implementation of techno­logical flowsheets using both adsorbent types and attempt to compare their technological properties. IRGIREDMET Institute was founded in 1871 as a laboratory for gold smelting and gold ore testing. In 1930 it obtained the status of the Research Institute. IRGIREDMET functioned as leading research center for gold mining industry in the former Soviet Union. At present it is the Open Joint Stock Company dealing with all s01t of research and design works for gold min­ing (ranging from geology to gold refinery). IRGIREDMET started development of ion exchange technol­ogy in 19641• The first stage of work (1964-1970) including development of principle flowsheet of RIP process was carried out jointly with the Moscow VNIIKHT Institute (All-Russian Scientific Research Institute of Chemical Technology)2• The flowsheet of RIP process is presented in Fig. I and includes the following basic operations: gold adsorption from pulp; washing of loaded resin; acid treatment; thiourea adsorp­tion; gold elution by acid thiourea solution; resin washing to remove thiourea; alkaline treatment of resin; resin washing and gold recovery from eluates by electrowinning. The technology developed and equipment used were tested for treatment of clayey ore of Kuranakh deposit at a pilot plant of the Lebedinsky gold complex ("Aldanzoloto" company, Yakutia, Russia). The pilot plant throughput was 200 t/day. At the same time IRGIREDMET conducted the tests on ion exchange technology for ore and concentration products of oper­ating gold plants and for ores of new deposits. Laboratory and pilot plant tests were done and developed initial data and process design criteria for designing of 15 plans of the former Soviet Union. In the course of this work a great number of newly synthe­sized anion exchangers including strong and weak base resins was studied, the peculiarities of anion exchange resins using two different raw material types ( ores and concentrates includ­ing clayey, carbonaceous, silver bearing, arsenic, antimony and base metals bearing products); some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption of gold and silver from silver gold ore, improved flowsheet for gold elution and resin regeneration, design of adsorption equipment including pulsation columns, design of electrowinning cells were developed; conditioning technology for pulp with complex ion composition prior to gold and silver adsorption was developed, etc.3·8• IRGIREDMET specialists took part in commissioning of practically all the plants in the former Soviet Union using RIP and RIL process including Lebedinsky, Kuranakh, Sovetsky, Karamken, Matrosov's plant and Mnogovershinny plants. Due to this works RIP process became standard technology for Russia and the CIS.

Jan 1, 1998

By R. T. Swinderman

"Virtually every article you read on safety has a statement to the effect: “It’s obvious that safety pays”. If it is so obvious, why is it so hard to answer these questions? • How does the Maintenance or Operations Manager convince the Plant Manager to spend money from the annual budget for safety improvements? • How does the Plant Manager influence Corporate to prioritize safety improvements? • How does an engineering firm persuade the owner to spend more on design and equipment up front to reduce risk? There are many cultural and structural reasons why it is so difficult to prove the obvious. In my opinion the main culprits are: the almost universally used ‘Low Bid’ process, variations in reporting incident statistics between industries and countries, and, the Generally Accepted Accounting procedures (GAAP) [or International Financial Reporting Standards (IFRS)]. Conventional wisdom is it’s smart not to spend more than you need to meet the minimum regulations and maximize production. But buying on price alone often harms people, degrades the environment, and reduces the company’s bottom line. How can this be? You met the minimum safety requirements and saved money by buying on price. Don’t those savings go right to the bottom line? When you buy on price you get minimum quality, minimum compliance and are often backed corner with no reasonable options to rectify the problems that arise from buying on price instead of buying on long term life cycle cost. Culturally few companies actually ‘walk the talk’. It is trendy to have giant billboards at plant entrances proclaiming world class compliance with quality and safety standards. Annual reports are embellished with safety slogans and sustainability statements. Behind the front gates and the glossy annual reports the message is clear: produce or be replaced. Only a few companies go beyond the window dressing and actually endorse, from the top down, continuously improving their safety culture. Those that do embrace safety, show significant performance advantages over their competition that are reflected in their safety, productivity and environmental records and, ultimately their financial statements and share price. Current accounting (and reward) systems make it unlikely financial managers will accept non-conventional approaches to justifying expenditures on safety because they are driven to report “hard” numbers that can be documented and are within the “GAAP or IFRS Rules.” But in reality, accountants quantify soft or intangible costs all the time in their financial statements. Justifying safety investments is greatly enhanced by quantifying what most financial managers would call intangible costs. Government agencies have no problem assigning intangible costs to justify regulations to improve safety. How many times have you heard that the regulation is justified because the cost to industry is X while the benefit to the society is 2 or 3X? How can they say that without including intangible costs? We find it hard to believe these government claims of benefits to society because we have been trained to think about saving hard direct costs to justify investments."

Jan 1, 2017

By Deepak Malhotra

Is operator training necessary for optimization of flotation plants? The answer is obvious-Yes. The author suggests a three-phase program for operators when new plants are built or new crews are hired in existing operations. Case examples are discussed to illustrate the benefits of operator training.

Jan 1, 1999

By Adolph V. Mitterer

International Minerals and Chemical Corporation operates one of six potash mines in the Carlsbad potash basin. More than 90 percent of America's potash is produced at Carlsbad and IMC accounts for about one-fifth of that amount, Since the Company began operations in 1941 it has mined nearly 50 million tons of ore. Of the two types of ore mined at Carlsbad the principal tonnage is sylvinite in which sylvite-potassium chloride-is the ore mineral. It is produced by IMC as well as by all other mines in the area, In addition to sylvinite IMC is the exclusive producer of langbeinite ore--potassium-magnesium sulfate. From its two ores, International produces a spectrum of 8 high-quality agricultural and industrial chemical products.

Jan 1, 1959

By A. L. Hannaford

Previous production at Spektakel was undertaken during the periods 1854 - 1888 and 1892 - 1901. During this period a total of 41,7 kt of ore grading 32% Cu was hand-sorted from 270 kt to 360 kt of ore mined. Initial open-pit mining was followed by underground mining, access being by means of an inclined shaft to the 85 fathom level. During the period 1946 - 1952 cement copper equivalent to 5,452 kt of blister was produced by leaching of oxidized ore. The Spektakel ore-body branches and coalesces both in plan and in cross-section which accounts for its remarkably complex configuration. Constituent rock-types are andesenite and various varieties of biotite diorite and of ?norite? (biotite-hypersthene diorite). Closely related spatially, and possibly genetically, but predating the above-mentioned basic rocks are bodies of biotite-bearing monzoritic rocks, locally termed shonkinita.

Jan 1, 1981

By E. Lovera

Social attention to environmental aspects, steadily increasing in European Countries, has been leading to a stricter regulation of many productive activities. Among them, mining and quarrying sectors have been often censured for their potential and real impacts on land and environment. Referring to dimension stone exploitation (also the terms ornamental stone or natural stone are here used as synonymous), quarries are often concentrated in extractive basins, where the resource is localized with suitable quality and quantity: this fact has sometimes raised critical environmental situations. Nevertheless, dimension stone quarrying represents in Europe a traditional and important economical activity, source of wealth and employment. Moreover, many natural stones take on a ?cultural? value and may be considered as ?classic?, as they have been exploited since antiquity and are element of the architectural heritage of many Countries. The sector relevance demands the research of a sustainable balance between social-economical needs and environmental protection. Actually, very restrictive environmental protection policies have led to severe limitations to quarrying activity, but the results do not seem to be completely positive in terms of sustainability: on the one hand, closing-down stone quarrying activities imposes a shrinkage in local, social and economical development; on the other, quarrying activity is pushed towards developing Countries, environmentally un-protected, simply moving and putting off to next future the problem. The challenge of the sustainable development of quarrying sector ? recently explored in the European Commission?s communication ?Promoting sustainable development in the EU non energy extractive industry? (COM-2000-265) ? should be achieved through a positive link between theoretical statements and practical effects: sustainability indicators may be an effective instrument to assess and monitor the environmental performance of the industry. The paper refers to the development of specific ecological criteria and indicators, which can be useful to measure and predict the eco-efficiency of a dimension stone quarry, finally pointing out where improvement efforts have to be focused.

Jan 1, 2003

By G. D. Elliot, R. L. Grayson, G. L. Winn

For the years 1990 and 1991, West Virginia's underground coal small-mine fatality rate was approximately 10 times higher than the national coal-industry fatality rate. Although the number of fatalities went down from 22 in 1991 to 17 in 1992, West Virginia still led the nation in coal-mining fatalities. A team of mining and safety professionals from West Virginia, interfacing with the Mine Safety and Health Administration and the West Virginia Office of Miners' Health, Safety and Training, studied this problem. A clear path for formal intervention was determined and is presented here.

Jan 1, 1996

By Henry N. McCarl

The New England States form the most northeastern portion of the continental United States and include Connecticut, Rhode island, Massachusetts, Vermont, New Hampshire, and Maine. These states have an aggregate population of over 10.5 million people, and an average annual population rate increase of about 1.3%. A great deal of new construction is required each year to meet the increasing demand for new homes, roads, offices, factories, and warehouses. Yet, prices of construction materials such as blocks and concrete are generally higher in New England than in other well populated areas of the United States. This is an indication of local demand being somewhat greater than supply, an atmosphere conducive to new developments in the production of construction materials. One such field of development is the rapidly growing Lightweight Aggregate Industry. Recent construction in Boston has used a great deal of lightweight aggregate. New structures using lightweight aggregate in lightweight concrete include the following: M.I.T.'s 20-story Earth Science Center and 17-story Married Students Housing Project Prudential Life Insurance Center, West End Redevelopment Project at Charles River Park, Hotel Americana, and the British-owned 33-story office building at 50 Pearl Street.

Jan 1, 1964

By Lihong Zhou, DAVOOD BAHRAMI

A reliable and stable ventilation system is essential to the safe operation of underground mines. The stability of a mine ventilation system becomes extremely critical while responding to a fire incident since an unstable ventilation system will pose a risk of airflow reversal. The reversed airflow could bring the fire contaminants such as toxic gases and smoke unexpectedly to working areas. In the past few years, there has been a growing interest in the study of ventilation network stability using the concept of resistance sensitivity, which is described as an indicator of how the airflow in an airway is reacting to a resistance change of other airways. Several methods of calculating the resistance sensitivity in a mine ventilation network have been carried out by researchers and scholars around the world. However, the proposed methods heavily rely on a vast amount of mine ventilation simulations, which are very time consuming and computer-power intensive, especially for a large-scale mine ventilation network. In this paper, a derivative method calculating the resistance sensitivities with a single mine ventilation simulation has been developed and implemented into a mine fire simulation software, MFIRE. The results from the derivative method were verified against the results from a traditional method. The derivative method has been proven to be reliable and accurate.

Jun 7, 2022

By Dávila-Pulido. G., L. Magallanes-Hernández, F. López-Saucedo, J. Batista Rodríguez, A. Uribe-Salas

"This paper presents the results of tests performed to study the effect of slurry solids concentration on the behavior of gas dispersion in industrial-scale mechanical flotation cells. The experiments were conducted at five concentrator facilities run by a Mexican mining company, specifically in the rougher bank of the lead/zinc flotation circuits. Those mechanical cells having significant contribution to the performance of the circuit, that is, the cells that enable high recovery, were characterized. The measurement protocol enables measurement of the superficial gas velocity, gas holdup and bubble size, and sampling of the mineral slurry. The measured data indicate that bubble size and gas holdup decreases as the concentration of solids increases. IntroductionThe process of mineral concentration by flotation is based on contact between particles and air bubbles, the selective adhesion of hydrophobic particles onto the bubbles, and the rising of the bubble-particle aggregates to the surface of the flotation cell to overflow over the lip to form the concentrate. It is now accepted that the physical and chemical process variables that control the flotation of hydrophobic particles are closely related to gas dispersion (Schwarz and Alexander, 2005). Gas dispersion is defined by the superficial gas velocity, Jg (Torrealba-Vargas, Gomez and Finch, 2006), the gas holdup, eg (Tavera, Gomez and Finch, 1997), the bubble size, d32 (Dobby and Finch, 1986; Gorain et al., 1995; Hernandez-Aguilar et al., 2004) , and the bubble surface area flux, Sb (Manqiu and Finch, 1989; Manqiu, Finch and Uribe-Salas, 1991). In recent years, the advances that have been made in sensor technology have enabled the characterization of gas dispersion in industrial flotation cells with excellent results (Gomez and Finch, 2007). This technology advancement has allowed the gaining of a deeper understanding of such complex mechanisms as carrying capacity (Yianatos and Contreras, 2010), collection efficiency (Gorain, Franzidis and Manlapig, 1997; Massinaei et al., 2009) and bubble coalescence (Finch, Nesset and Acuña, 2008; Zangooi, Gomez and Finch, 2010)."

Jan 1, 2017

By Stephen Navin, Pablo Ferradas, Carlos Silvestri, Alexander Markov, Jon Kaneshiro

In the high Andes of Peru, two tunnels are being constructed totaling nine kilometers in length at an elevation of over 4,500 meters. The tunnels convey freezing and crystal-clear waters from rainfalls, streams, and lakes for the consumption of Lima. The drill and blast 3-meter wide by 4-meter high tunnels are being driven from both ends through folded and sheared volcanic tuff, andesite, agglomerate,and limestone, where groundwater inflow is high. This paper describes the design geological and groundwater inflow investigations and construction.

Jan 1, 1999

By Stephen R. Brown

The principles of quality management are well developed and, from a practical stand- point, thoroughly implemented in the process industries of Japan. Although these principles are now applied to the U.S. manufacturing industry, and as a result, the steel industry, they have been largely ignored in the non-ferrous and precious metals industries. This paper presents the concepts and practical approaches to implement a total quality management program. Contrary to the beliefs of many managers, such a program increases yields, recoveries and output while it decreases unit costs. In fact, quality management incorporating statistical process control will be an essential ingredient for metallurgical plants to effectively compete in the '90's.

Jan 1, 1991

By S. K. Kawatra

Three International Symposiums-the 14th International Minerals Processing Congress, the 17th APCOM, and the SME-AIME Fall Meeting special symposium on Design and Installation of Com¬minution Circuits-held in 1982 contained a number of papers relating to the fundamentals of processing coals and metallic minerals. In addition, many papers were published elsewhere in the literature. Some of the more significant papers are discussed below. Flavel reviewed key performance parameters, such as energy-size relationships for crushing processes and presented a fundamental basis for optimizing crusher productivity and possibly for development of improved crushers. Pascoe et al. reviewed the use of such control schemes. Magerowski and Karra presented a paper on a computer program developed to and in the design of crushing circuits. The problems associated with the scale-up to very large ball mills were discussed by Arbiter and Harris, and by Kavetsky and Whiten. Both groups concluded that limits on mill productivity arise due to problems associated with particle breakage and transport through mills. Austin et al., and Herbst and Rajamini reviewed the state of the art for the use of grinding circuit simulators for design and control. The effects of mill operating and design parameters on selection and breakage were discussed in detail. The philosophy of control and instrumentation for grinding circuits was extensively discussed by Kawatra and Seitz. Their paper presented for the first time an analytical basis for the inferential particle sizing technique and provided a fundamental basis for the implementation of this technique. The effect of reagent addition variation's on the performance of coal flotation circuits was reported by Kawatra and Waters, and on sulfide flotation circuits by Klimpel et al. Both groups analyzed circuit behavior from a kinetic point of view and reached similar conclusions on the effects of collectors and frothers. The computer simulation of an iron ore flotation circuit also was reported by Kawatra et al. In this work particular attention was paid to the phenomena of froth overloading. Klimpel et al., Kawatra and Waters, and Niemi et al. discussed the philosophy of control by flotation circuits from a fundamental kinetic point of view. An extension of the use of high intensity magnetic separators to the beneficiation of specular hematite was discussed by Thayer and Linkson.

Jan 5, 1983

By Gerry Norton

The overall economics of a coal production unit are governed by a number of interdependent parameters which individually and collectively affect the final result. A business judgement is measured through return on investment considerations and in this respect, a sensitivity analysis proves useful. Figures 1 and 2 show how the various parameters affect return on investment through unfavourable change from planned or expected values. In the case of metallurgical coals, the selling price negotiated is the primary and most sensitive variable, followed by transportation, clean coal yield and capital funds invested in mining. It is clear that coal preparation plant capital and operating costs are the least sensitive to R.O.I. For energy coals, the selling price is determined by heat energy content (x cents per million BTU's) and is therefore not con¬sidered as an interdependent variable. In this case, transportation cost is the major primary factor affecting the level of income. Again the amount of saleable clean coal or total yield has a major effect on return on investment. Most of the factors considered in Figures 1 and 2 are fixed and unfavorable change from planned values becomes critical but clean coal yield is to a great extent controllable during actual operations. Once the theoretical yield for a particular coal has been determined, the optimum return is achieved by approaching this theoretical yield as nearly as possible in practical commercial operation.

Jan 1, 1975

By T. B. Thompson

The Cripple Creek diatreme-intrusive complex is known primarily for its vein telluride-gold ores and, for major veins, their great vertical range (>990m). Less well-documented are the ores dispersed into the wallrocks adjacent to veins, the ores associated with hydrothermal and tectonic breccias, or mineralized zones within fluvial, lacustrine, and volcaniclastic rocks deposited within the diatreme complex. The ore-gangue minerals Here precipitated from oxidized, alkaline fluids that yielded an abundance of carbonate, sulfate, and oxide minerals along with minor base metal sulfide and precious metal telluride-s. Wallrock alteration is quite limited adjacent to veins and somewhat more extensive within hydrothermal and tectonic breccias.

Jan 1, 1991