Search Documents

By Federico Pagliacci

Continuous Flight Auger (CFA) technique represents an important technological advance in the construction of piles in soft soils. The possibility of excavation under the water table with no need for drilling fluids, along with high productivity, have resulted in this technique’s becoming widespread in many countries. However, CFA technology has limitations because of its difficulty in penetrating hard layers and cross strata with cobbles and boulders. In these situations, pile verticality may be an additional problem. The Cased Augered Pile (CAP) technique consists of penetrating the soil with an auger housed in a casing. Two independent rotary heads sliding along the rig mast operate the auger and the casing. By adjusting the height of the casing shoe and auger bit according to soil type, it is possible to drill piles in very severe conditions - in the presence of cobbles and boulders - and to socket the pile into the rock. The use of a steel casing enables improved pile verticality. Therefore, the CAP technique is also used to construct secant piles to be used as diaphragm walls. The limitations of this technology are the depth, usually no more than 27 m (88 feet), and the size of the rig that supports the drilling tool, no less than 70 t (77 short tons) in working conditions. This paper illustrates CAP technology, the drilling system, and the characteristics of concrete and steel reinforcement and offers a case study of the Palermo-Carini second railway line, which used CAP to construct the new 30 km (18.6 mi) railway line, 20 km (12.4 mi) of which passes through the very congested downtown area of Palermo. More than 300,000 m (186.4 mi) of piles have been drilled in dense calcarenite formations with unconfined compressive strength of 15-25 MPa (2,200-3,600 lb/inch2), soft clay,

Jan 1, 2017

By David S. Graham, Joseph D. Bailey, Paul J. Axtell, Michael K. Muchard

"Two instrumented test piles were simultaneously subjected to a static lateral load test by jacking the piles apart. One of the piles was loaded in axial compression via kentledge during the lateral load test. Both piles were constructed in an identical manner. These piles were constructed and tested as part of a construction-phase load test program for a floodwall improvement project along the Missouri River in Kansas City, Kansas. Details of the subsurface conditions, drilled pile construction, instrumentation, and load testing procedures are described. Data collected during testing of the piles are presented and compared. Potential effects of the axial compressive load related to observed differences in pile lateral response are discussed.INTRODUCTIONTwo instrumented test piles were simultaneously subjected to a static lateral load with one of the piles also subject to a combined axial load during testing. The load test program was part of a floodwall improvement project in Kansas City, Kansas. Known as the BPU floodwall, the floodwall runs along the south bank of the Missouri River at a Kansas City Board of Public Utilities power generation and water treatment facility. The project location is shown in Fig. 1.Drilled, 2-ft (610-mm) diameter piles were designated by the designer, the U.S. Army Corps of Engineers (COE), as the foundation type for supporting extended floodwall footings. The drilled piles are fully cased, cast-in-place concrete, reinforced with a steel 12x74 (310x110) H-pile. In order to test soil lateral response and pile structural response under combined loading, the COE required that both a lateral test and combined lateral and axial test pile be constructed and tested. In order to most efficiently test both piles and to allow for simpler comparison, the two piles were simultaneously laterally loaded by jacking the piles apart, applying a maximum lateral load of 195 kips (867 kN). A constant axial load was applied to the combined test pile by kentledge prior to lateral loading and was maintained for the duration of the lateral load test. The total weight of the kentledge was 61.5 kips (274 kN). Fig. 2 shows the test setup."

Jan 1, 2017

By M. Kitazume, H. Imai

The deep mixing method was developed in Japan and put into practice in the middle of 1970s. Since then, the wet and dry type methods have been applied for various improvement purposes in Japan. One stork of mixing tool produces a column shape of stabilized soil in a ground. By the series of productions, arbitrary shape of improved ground can be constructed by overlapping each columns. It is specified to complete the overlapping within 24 hours in order to ensure the tight connection of the columns. However, it can not be completed within the specific time in some cases due to bad weather or machine trouble, which causes a cold joint in the improved ground. In this study, the influence of the cold joint to the behavior of the block type improved ground is examined by a series of centrifuging model tests and FEM analyses. It is found that the ground behavior is influenced by the position of the cold joint, where the cold joint at the sea side shows a little influence to the behavior but one at the port side causes large decrease in the stability of the improved ground.

Sep 8, 2021

By R. Paul De Bruyn

A. Crane Check List -- Make -- Model -- Year of Manufacture -- Where is load chart? Is it for this crane? -- Boom style and length -- Boom tip drawing (sketch) for fixed lead connection. Has the crane manufacturer been consulted on the point of attachment? -- How many drums; diameter and length of wire rope. -- Is the single part line pull enough to lift pile or hammer on single part line? -- What is the effective weight of the whole driving system - leads, pile, hammer, etc? -- Are there any auxilliary hydraulic systems? Are the line pulls on these adequate to lift the pile or hammer? -- What is the anticipated working radius? Will the spotter collapse to that length? -- Nature of foundation under crane - barge, marsh, unstable sand, etc. -- Does the crane meet OSAH and state regulations -current certification. Note - the operator is responsible for compliance with regulations. -- Is there any extra weight added to counterweight by compressors or hydraulic systems? What does crane manufacturer say? Consult factory before adding.

Jan 1, 1990

By F. Keith Jacobson

To be involved in the construction of a deep dredged caisson for a major bridge pier is one of the most rewarding and professionally challenging experiences one can have in the bridge construction business. That experience was doubled in the construction of the two deep dredged caissons for the Highway 82 Bridge over the Mississippi River near Greenville, Mississippi. The challenges and the construction risks associated with constructing these two dredged caisson pier foundations highlight the construction engineering innovation associated with major bridge pier construction. The 1,378-foot Main Span of the Highway 82 Bridge makes it the longest cable stayed bridge span over the inland rivers of the United States. The main piers for this bridge are supported on two dredged caissons measuring 80-feet by 122-feet in plan, founding 200-feet and 170-feet below the river surface. The challenges of constructing these caisson structures, sinking them through 70-feet of water to the river bottom and then excavating and further sinking them to the founding grade without exceeding the design tolerances, were enormous. The construction engineering opportunities for innovation included major breakwater structures to create a friendly environment in 11 ft/sec currents, the first time use of Articulated Concrete Mattresses for river bottom scour control, unique air dome design to maximize the buoyancy of the caisson structure while floating, a caisson guide system to assure positive control and positioning of the caisson during the initial sinking phases, and a comprehensive sinking plan to assure maximum control and minimum risk. Many of the innovative solutions to the construction challenges on this bridge will be incorporated into future caisson construction projects on the lower Mississippi River.

Jan 1, 2013

By Jamey Rosen, Georgette Hlepas

"Bluestone Dam is a concrete gravity structure with an overall length of 2,060 feet and a maximum height of 165 feet above the streambed. Several major project modification designs have been implemented and additional modifications are currently in construction and design phases. Due to the various modifications since original construction was completed in 1948, detailed documentation with visualization of the project features is needed. A three-dimensional model of the internal and external features of Bluestone Dam was generated from LiDAR data, survey information, and other data sources. One of the key features of interest in this model is an accurate visualization of over 200 dam anchors based on downhole anchor surveys. The model is accessible in Microstation and Geographic Information Systems (GIS), allowing users to rotate the anchors in three dimensions; view them in the context of geology, internal dam structural features, historical construction records, site photographs, bathymetric data, and instrumentation data. Users can “click” on individual anchors to view associated construction details and open a comprehensive installation packages. The model will be used by the United States Army Corps of Engineers (USACE) as part of a larger Geospatial Data Management System as a historical accounting of the project construction data, and be a long-term living document for use by both design engineers and operations staff to assess dam safety risk and to design future project modifications.IntroductionDuring the life of any project, critical data concerning the construction and performance history are required to be collected and maintained. The data collected prior, during, and post-project construction help with the design process, ensure that the project is built to specifications and is performing as per design intent. During the Post-Implementation Evaluation (an evaluation performed after a major project modification), these data are used to visualize the repairs, verify the construction was performed per design intent, and document the history of the construction phases, associated test results, and overall effect on the project. The project described in this paper is the construction of a system of tools to effectively use these data.Data collected and maintained during the operations phase helps to ensure that the project is continuing to perform as per design and aids in advance warning of any potential failure or required maintenance. Dam Safety, Emergency Management (EM), and Operations and Maintenance personnel can use the system to verify the status of the project in preparation for a high flood event. For example, if there is repair work being performed on a critical feature of the project that would affect the operation of the dam structure during a flood event, Operations personnel would be responsible to update the status of the system such that Dam Safety and EM would be able to identify the feature that is out of service, its date of expected repair completion, and the implications during a flood. In addition, risk assessments typically require a full history of the project and its performance. Any concerns that arise concerning the safety or performance of a project will require a full documented history of the project and its components. Proper documentation and data management are key in this assessment process."

Jan 1, 2016

By Ronald Damen, Dion Denes

"Friction fatigue is the loss of soil-pile friction around the shaft area of the pile. It has been observed during impact driving of piles, and has been modelled to a limited degree using physical scale models. This paper proposes the use of high strain dynamic pile testing to assess and quantify friction fatigue in impact driven piles. The method is applied to two case studies: one on a project off the north-west coast of Australia and one on a South Pacific Island. On both sites calcareous sand layers are present. Pile Driving Analyzer (PDA) monitoring has been conducted during impact driving of steel piles, which allowed for assessment of shaft resistance development both with depth and with progressive driving, by use of wave equation signal matching. Lessons are drawn from the case studies to improve future observations.INTRODUCTIONFriction fatigue is the loss of soil-pile friction around the shaft area of the pile, under cyclic loading or during pile driving. The phenomenon has been frequently observed in some non-silica sands, such as pumice sands and calcareous sands and has been the subject of academic study.The occurrence of friction fatigue impacts the driving behaviour of piles and the shaft friction component of the ultimate geotechnical strength (Rd,ug). If potential friction fatigue is not recognised in the design phase of a project, required pile toe levels can be significantly underestimated. This could lead to extra cost and delays, or, if no adequate pile verification is conducted, to geotechnical failure or underperformance of piles. This is especially true in remote locations, such as Pacific islands, where calcareous material is often present.A better understanding of the phenomenon would aid both pile design and driveability assessment. This paper proposes the use of high strain dynamic pile testing to assess and quantify the effect of friction fatigue from impact driving. Two case studies are presented in which high strain dynamic testing has been conducted on driven piles in calcareous sands to illustrate the method.BACKGROUNDFriction fatigueThe geotechnical strength of piles is composed of the resistance to static loading by the base of the pile and the shear resistance between the shaft of the pile and the adjacent soil. The latter is often referred to as the shaft resistance or shaft friction.During impact pile driving, a decrease in shaft resistance is often observed. Although this phenomenon is also observed during vibratory pile installation, this paper deals predominantly with impact driving. This decrease in material strength from the tip of the pile influences the shaft resistance and may be either temporary or permanent. Temporary reduction in shaft resistance is common in cohesive soils and is thought to be caused by excess pore water pressure, which has insufficient time to dissipate. This phenomenon, commonly referred to as set up, is observed to a significantly lesser extent in non-cohesive materials such as clean sands (Rausche et al., 2004)."

Jan 1, 1900

By Hugo Meggitt, Damian R. Siebert, Wystan Carswell

Excavation-induced ground movements are a critical component in the design and construction of deep excavations in urban settings due to the potential adverse effects on adjacent structures and infrastructure. Ground movements are influenced by soil stratigraphy, soil properties, adjacent structures, and construction means and methods. The use of empirical relationships, computer models, and reliance on experience with similar excavations in similar soil conditions often provides a basis for predicting excavation-induced ground movements. In this paper, data from 21 deep excavations approximately 20 ft to 75 ft deep supported by concrete diaphragm “slurry” walls in the Greater Boston area are compared to published literature, considering how different foundation systems (e.g. shallow foundations, caissons, and piles) of abutting structures have been affected by adjacent excavations. The influence of construction method (conventional vs. top-down) on adjacent foundation movements indicate that top-down construction typically results in smaller foundation movements. INTRODUCTION Estimation of ground movements due to excavation is a challenging endeavor, even with complex three- dimensional finite element modeling and high-order constitutive models that are increasingly available in modern engineering practice. Aside from the expense of the soil exploration and testing used to inform these higher-order models, the challenges of modeling past stress history, adjacent structures, and the groundwater conditions during excavation require not only large investments of time during design but also validation from past experience (to avoid a “garbage in, garbage out” paradigm). While site conditions such as soil stratigraphy, soil properties, groundwater conditions, and as-built conditions of adjacent structures can be obtained, measured, and estimated, the effects that means and methods of construction have on ground movements are difficult to quantify. During early phase design, assessments of predicted ground movement are unable to account for all aspects of project construction, nor is it cost-efficient to fully design an excavation while project parameters such as site size and excavation depth are under consideration by the design team. While construction is in progress, benchmarking support of excavation performance and associated ground movements in the context of successfully completed projects allows for a more nuanced view of system performance and provides the opportunity for more informed decision-making (if required) as construction proceeds. For these reasons, the use of empirical relationships and the collection of historical support of excavation performance holds high value for the practicing geotechnical engineer at all phases of the project.

Jan 1, 2019

By K. Rainer Massarsch

"Part 1 of 2 By K. Rainer Massarsch, Geo Engineering AB, Stockholm, SwedenINTRODUCTIONConstruction activities, such as driving of piles and sheet piles, soil compaction or excavation generate noise and vibrations. In populated areas these can have a negative impact on the environment, disturb inhabitants and, under unfavorable conditions, cause damage to buildings and installations. This condition is aggravated by the growing public awareness of environmental issues and the increasing use of vibration-sensitive electronic equipment and machinery in industry. In many countries, environmental regulations are enforced more stringently and limit or even prohibit the use of impact or vibratory hammers. This development has restricted the use of cost-effective foundation methods, such as driven and vibrated piles and sheet piles.Vibration problems are gaining importance in many European countries and extensive research has been performed during the past decade, especially with respect to traffic vibrations (Massarsch, 2004). Significant progress has been made owing to the availability of high-quality field measurements and an improved theoretical understanding of how vibrations are generated and transmitted through soil layers. These findings can also be applied to vibration problems associated with construction activities. However, this information is not yet appreciated by the geotechnical profession and even less by the construction industry.This paper discusses the effects of ground vibrations on the surrounding soil and on buildings, with particular emphasis on the different mechanisms of damage that may occur. Guidance is given on the elements which should be taken into account in an assessment of risks associated with piling projects. A simplified method is proposed for assessing the risk of settlements or strength loss in soil deposits. Limiting vibration levels are presented, based on the Swedish standard, which can be used to assess the risk of damage to buildings. Aconcept to predict ground vibrations caused by pile driving and the mechanisms which control the propagation of ground vibrations, will be presented in the second part of this paper."

Jan 1, 2004

By Damien Enright, Franz-Werner Gerressen

CFA/ACIP pile is the most used single pass drilling method for deep foundation installations. It is constructed by rotating and driving a Continuous Flight Auger (CFA) into the ground at a controlled speed to the specified pile depth. Concrete is then pumped under continuous positive pressure through the hollow stem of the auger to fill the borehole as the auger is withdrawn. CFA/ACIP piles are preferred due to their high daily production capacity when used in suitable soil conditions. CFA/ACIP piles have been installed in the United States for decades and the industry has seen a huge development in equipment, installation process, monitoring and more. Nowadays, CFA/ACIP piles are installed using fully computer monitored drill rigs rather than a bulky crane and lead setup. Because of the torque and crowd offered by these rigs, piles can be installed to depths of more than 100 feet and diameters up to 48 inches. New age crane-based equipment with leader systems are than welcome to substitute old fashioned bulky cranes These new age crane-based systems combine the benefits of sufficient hydraulic power, fully equipped software, etc. with the additional benefits that they can do single pass drilling without extension systems, even when drill depths of more than 100 feet are required. The paper will explain the construction process and will discuss some jobsite references and experiences made using the new age crane-based equipment.

Oct 1, 2022

By Ernest Naesgaard

Post-grouted micro-piles were used for the seismic upgrading of the Vancouver International Airport Domestic Terminal Building (DTB). The micro-piles provided vertical resistance to both uplift and compression loads to supplement the existing timber pile foundations ability to resist the earthquake induced forces, and to provide foundation support at locations where the installation of traditional driven piles was difficult. This paper describes the site conditions, design rationale, installation method and quality control testing procedures. Site and Subsurface Conditions Vancouver International Airport is located within the central portion of Sea Island, Richmond, British Columbia (Fig. 1). Sea Island is bordered by branches of the Fraser River on the northeast and south sides and the Strait of Georgia along the west side. The natural grade of the island is part of a large delta that has been built up over several thousand years. The general pattern of sediment deposition has followed the direction of the Fraser River flow from east to west, and has built up soft sediments of about 200 m thickness at Sea Island (Luternauer, et al. 1993, Mathews and Shepard 1962). The original grade in 1962 prior to the existing Airport Terminal Building development was at about geodetic elevation 1.1 m with a grass and topsoil cover.

Jan 1, 2004

By Silas C. Nichols, Jennifer E. Nicks

"Limit states design (LSD), or load and resistance factor design (LRFD), is a method to account for the uncertainty in loads and resistance through a reliability calibration that requires all applicable limit states (strength, service and extreme) to be checked during foundation design. LRFD has been in use internationally for several decades; however it wasn’t until recently that engineers working on highway projects were required to use the method for the design of highway bridges and other appurtenances. Although the bridge community has been using a form of limit states design for structural components since the early 1970s, the design of foundations for bridges, walls and other geotechnical features had long been performed using allowable stress design (ASD), whereby all uncertainty in loads and material resistance is combined in a single factor of safety. While the move to LRFD was viewed as a more rational approach for the design of bridges and structures, the transition to its use for geotechnical engineering has been met by many with confusion and difficulties in application. This article will revisit the history of transition from ASD to LRFD for geotechnical engineering, summarize the status of the transition and issues with its use, and briefly discuss some emerging research opportunities for improving and advancing the design platform.Background and HistoryUntil about a decade ago, foundations and substructures for bridges were traditionally designed using ASD, while the superstructure was designed using load factor design (LFD), a precursor to LRFD that incorporated factored design loads but no risk assessment. This combination led to uncertain and incompatible safety margins in design for the various bridge components. In 1986, the American Association of State Highway Transportation Officials (AASHTO) Subcommittee on Bridges and Structures (SCOBS) concluded that the standard bridge specifications in use at the time for U.S. transportation projects had significant inconsistencies and gaps, wasn’t up to date with emerging technology and that the development of new specifications was warranted. The proposed solution by the subcommittee was to transition to a more coherent method of design where applicable failure and serviceability conditions could be evaluated considering the uncertainties associated with loads and resistance."

Jan 1, 2015

By David Miller

"The biggest concern about using soil mixing is the inability to observe physically the final product, which has led to a lack of confidence about what is in the ground. After all, you can’t see it and you can’t taste it and you can’t smell it, so are you sure it’s soil mixing? In addition, there are variations in techniques, tools and monitoring that have led to additional skepticism and the desire to “elevate” the product. This skepticism is why the industry is so scrutinized even when there are other technologies being used that do not experience nearly the same level of scrutiny. With other techniques, even with a slurry wall, you can see the backfill before it goes into the ground, and drilled piers have careful evaluation of the concrete mix even before placement into and verification of the open hole. Essentially, you get control over the final material. There is less control in soil mixing, and it’s very dependent on in-situ conditions. These factors make it difficult to rely solely upon installation parameters, quality control (QC) and verification tests. At some point, you may need to apply some engineering judgment.Start at the BeginningThe availability of sufficient and accurate geotechnical data (soil type, heterogeneity, shear strength parameters, variability, etc.) is important in establishing the material that will be drilled. This data will also help in determining the proper mix design to achieve the desired soil cement properties. Many factors must be considered when designing the mix and the mixing program, including any debris in the ground, different soil properties and varying moisture contents.Each of the various factors affect the final properties of the soil cement, so it really takes careful planning and evaluation of the mix design through iterations by looking at the soil types and adjusting the mixes. Clay is going to behave very differently than sand in both mixing efficiency and final properties. That is, the presence of clays results in more difficulty in achieving higher strengths and to physically mix the soil and the binder, whereas the presence of sands results in more difficulty controlling the final permeability."

Jan 1, 2017

By Eric J. Pederson

The down hole hammer is widely used in specialty geotechnical construction. The common uses include tie-back anchor installation, micropile installation, and general soil/bedrock drilling operations. Veit used these techniques to develop a cost effective way of installing the foundation system for University of Minnesota Football Stadium. The soils present at the site of the stadium contained layers of concentrated cobbles and boulders. The geotechnical engineer recommended a driven pile system, and the base bid outlined in the project documents consisted of an H-Pile using a 14x73 pile section. Veit submitted an innovative alternate consisting of using a rotary percussion system to install a 12? O.D. pile. This paper will show that this pile type and installation method was the correct choice for the project. The design criteria for the compression, uplift, and lateral capacities and deflections were met, while eliminating pile damage. The method resulted in a significant cost savings to the University and maintained the project schedule.

Jan 1, 2008

By Lok M. Sharma

Development of brownfields is of great interest in these days. Such fields are not easily adaptable for foundations of structures. The uncertainties in ground behavior present challenges of unpredictable subsidence that could be detrimental to the build up facility. A desalination plant had to be located along the seashore, close to the needy population and the existing water supply infrastructure. The available site had been developed as a recreational park area over a dumped construction demolition debris landfill along the coastline. To construct a desalination plant comprised primarily of large concrete basin tanks on slab, founded on the debris fill had its challenges. A ground improvement system in the form of vibro replacement stone columns was designed and constructed. Approximately 5,000 stone columns were installed across the site. This paper describes the analysis process, the design, field load testing, and installation of stone columns. Difficulties during construction and monitoring aspects are briefly described. The plant started operations in the summer of 2008 and to date has performed satisfactorily. When properly designed, the development of brownfields is achievable at other sites.

Jan 1, 2009

By Bernard H. Hertlein

"When the Deep Foundations Institute (DFI) was founded, quality assurance and quality control (QA/QC) of foundation construction was rudimentary. Nondestructive testing (NDT) was a nascent technology, known to very few people, and very limited in its capabilities and applications. In the four decades since the DFI became a reality, NDT researchers and practitioners have taken advantage of technological advances to improve those existing testing and analysis techniques, and to create new ones that have all contributed to the engineering body of knowledge. This has enabled contractors to improve the quality and reliability of their products, and engineers to design more efficient foundations.Through its regular series of seminars, publications and annual meetings, the DFI has been vitally important in educating the deep foundations industry about the capabilities and benefits of NDT methods. In turn, NDT results have helped the industry identify problems in deep foundation construction, determine the causes of those problems, and improve design constructability and construction practices to increase the quality, reliability and efficiency of all types of deep foundations. This presentation reviews the evolution of several important NDT methods, and the contributions that they have made to foundation quality.THE BEGINNINGSThe Deep Foundations Institute (DFI) was incorporated in 1976 in the State of New Jersey as a 501(c)(6) non-profit association. The DFI is a consensus organization of Contractors, Engineers, Owners and Suppliers involved with the design and construction of all types of deep foundations. The purpose of the DFI was and still is to improve the planning, design and construction of deep foundations by educating all those involved, sharing best practices, and promoting the adoption of new technologies that improve quality, productivity or safety.This is well expressed in the current DFI Mission Statement: To bring together multi-disciplined individuals and organizations to find common ground and create a shared vision and a consensus voice for continual advancement in the deep foundations industry.At the time the DFI was born, nondestructive testing for verifying the quality and integrity of deep foundations was in its infancy, its growth constrained by the technology, or lack thereof. Some visionary engineers of the time understood the physics of the potential methods, and therefore the possible capabilities, but were frustrated by the lack of technology to work with. Electronic equipment was mostly analog, and the few digital data acquisition systems that were available had such slow sampling rates that they were incapable of recording rapid event sequences or short duration events such as those used in modern integrity tests. For example, Jean Paquet, a leading research engineer at the French National Construction Institute, (Centre Experimentale de Recherche et d’Etudes du Batiment et des Travaux Publics, or CEBTP) patented the frequency-based analysis procedure for the Transient Dynamic Response (TDR) method, aka Sonic Mobility or Impulse Response, in 1974, but it was not until 1977 that analog data acquisition systems became fast enough to turn his theory into a reality."

Jan 1, 2017

By Don W. Dotson

In 1962, Kondner prepared several papers dealing with hyperbolic stress-strain response of cohesive soils. The following year, Brinch Hansen proposed 80% and 90% failure criteria for stress-strain behavior of cohesive soils. Fellenius was instrumental in popularizing these failure criteria for pile load tests and offered a direct solution equation for the failure load according to the 80% failure criterion. Since the 90% Criterion has been incorporated into the International Building Code, equations for the direct solution of the failure load at the 90% Criterion would be useful to practicing engineers. This Technical Note supplies the derivation methodology for the 80% Criterion and provides expressions to determine the load and deflection at failure for the 90% Criterion.

Aug 1, 2013

By Ali Ebrahimi, Jeremy M. Gasser, Cuneyt Gokmen, Paul J. Sabatini, Roneet Das, William Tanner, Amir Ahmadipur

There are safety concerns related to operation of heavy equipment over coal combustion residual (CCR) impoundments during construction of the impoundment closure programs. As part of a pilot study prior to a full-scale closure construction, an access pathway and working platform were designed and constructed to facilitate equipment access for construction of deep soil mixing (DSM) zones on the ash delta of a CCR impoundment. The access pathway and working platform was constructed using shallow mass mixing with cement at the CCR surface to address safety concerns related to the geotechnical behavior of CCR. This paper describes the data from the instrumentation system which was implemented to monitor the geotechnical performance of the CCR during the pilot study. The instrumentation system included monitoring of the ground movement, vibration, and porewater pressure within the ash delta of the CCR impoundment during a pre-construction load testing, equipment mobilization over the access pathway, and DSM column installation over the working platform. INTRODUCTION A deep soil mixing (DSM) pilot study was conducted at a coal combustion residual (CCR) surface impoundment to evaluate mix designs and construction techniques for the regulatory closure. The DSM columns will create a wall which will separate and retain the CCR in a consolidated footprint separate from the closure by removal portion of the footprint and provide a barrier between the two areas of the surface impoundment. Historically, the surface impoundment received CCRs including fly ash, bottom ash, boiler slag, and gypsum, along with other byproducts produced from flue gas desulfurization (FGD). The predominant CCR in this impoundment were fly ash and bottom ash. The primary goals of the DSM pilot study were to assess the mix design strengths and to evaluate DSM construction techniques that could reach the design mixing depths of up to 90 ft. The DSM test columns were installed on the CCR delta approximately 500 ft from the nearest impoundment dikes. Another objective of the pilot study was to develop, construct, and monitor an access pathway for safe passage and movement of construction equipment on the CCR delta.

Jan 1, 2019

"What can we do in ground engineering to reduce damage to the environment, to repair historic pollution, to reduce our demand on basic resources and to reduce the carbon footprint of our industry? Some developments in geotechnical engineering are already heading in the right direction. These include reductions of ground pollution from grouting, improved dewatering procedures and advances in mix-in-place processes, ground improvement and jet grouting.There is increased interest in certain promising technologies (for example, drilled partial or full displacement piles), but this approach remains for the moment somewhat avant-garde. These piles require substantially greater power to install, and the overall sustainability balance for general application has yet to be shown to be in their favour. They are particularly suited to polluted sites where the problem of dealing with spoil would be costly and where, in the past, driven cast in-situ piles would have been employed. Drilled displacement piles offer some environmental benefit over driven piles in that they cause far less drawdown of potentially contaminated near-surface ground into sensitive, underlying aquifers.There is also great interest in various means of increasing the frictional capacity of bored piles, both conventional auger and continuous flight auger (CFA) piles, by threading or ribbing the soil/pile interface. The increase in adhesion capacity allows reduction in the pile dimensions necessary for a specific load. This obviously leads to less construction waste, but also to less permanent material consumption in the piles and also in the pile caps.The role of ground improvement remains significant for brown land sites and lower capacity foundations. Information technology (IT) has improved the quality assurance of stone column construction, for example. From the sustainability point of view, this is a good news method; here is no cement, no pollution and little obstruction to future redevelopment. We now need to introduce recycled crushed materials instead of natural aggregate as general practice and the technique’s green credentials will be really compelling."

Jan 1, 2009

By Ryan P. Sullivan, G. Alan Klevens, Jian Huang

"BACKGROUNDLake Hamilton in Hot Springs, AR was created in 1932 when the Arkansas Power and Light Co. completed Carpenter Dam on the Ouachita River to generate electricity. Today, the 7,200-acre (2,914 hectares) impoundment is one of Arkansas’s most popular recreational and residential lakes.U.S. 70 crosses Lake Hamilton by means of a seven-span bridge featuring nine steel girders per span. Constructed between 1982 and 1984, the 1,410-foot long (430m) bridge carries four lanes of traffi c across the lake. The bridge is supported by six intermediate reinforced concrete piers composed of hammer heads, stems, footings and seals, which sit on the underlying rock. (See Figure 1). The bridge rises to a maximum of 33 feet (10m) above the surface of the lake and the footings and seals extend a maximum of 29.5 feet (9m) below the surface of the lake. The seals are situated on hard, fractured sandstone and shale.Routine underwater inspections in 1993 revealed large cracks in the lean seal concrete and refl ective cracks in the reinforced concrete footings. Infrastructure Engineers, Inc., The Arkansas State Highway and Transportation Department’s (AHTD) design consultant, then conducted an in-depth underwater inspection of the pier foundations. The investigation included cross-hole sonic logging, singlehole sonic logging, visual examination and strength testing of core samples, and petrographic analysis.The investigation revealed extensive cracking and low-strength concrete within the seals of all intermediate pier foundations. Many voids within the seal concrete had become fi lled with silt. There was evidence of continued seal deterioration between underwater inspections.AHTD and its engineers considered three rehabilitation solutions in the preliminary engineering stage: micropiles, a cofferdam supported concrete jacket, or a pile supported concrete jacket. The three alternatives were estimated to cost $1,250,000; $4,320,000; and $3,030,000 respectively. All three options would transfer the loads from the pier footing directly to the rock below, bypassing the seal concrete."

Jan 1, 2007