Search Documents

By L. Beiza, L. Velásquez-Yévenes

Chalcopyrite is by far the most abundant copper sulphide on Earth, but it has proved to be problematic in its processing by leaching, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface during leaching. This study is focussed on the electrochemistry of chalcopyrite dissolution in acidic chloride system, which has recently gained attention as a feasible alternative to conventional sulphate media for chalcopyrite leaching. It is well understood that chalcopyrite dissolution from mineral grains depends strongly on the solution redox potential at the mineral surface as well as the composition of the product layer that may form on its surface. The chloride ions in solution support the Cu(II)/Cu(I) couple as the primary oxidant, as they can form complexes with the cuprous ions formed, increasing the dissolution rate. Additionally, these ions increase the potential range where chalcopyrite can be oxidized. The chemical reaction that occurs on the surface of chalcopyrite in chloride solutions in the presence of cupric ions will be characterized and the coulometry of the reaction will be reported to understand what is happening on the surface of chalcopyrite. Electrochemical experiments have been carried out to investigate the behaviour of mixed potential by open circuit potential (OCP) measurement for 30 minutes using sulphuric acid at pH 1 under nitrogen at 25⁰ C. The effect of chloride was analysed at 0, 20, 50 and 100 g/L and cupric ions from 0 to 50 g/L. The potentials obtained were then used to carry out chronoamperometry tests for a period of 30 minutes in absence of cupric ions. The mixed potential did not show a significant difference with an increase in cupric concentrations in the absence of chloride. Increased mixed potentials and current densities were observed at higher chloride and cupric concentrations. Chronoamperometry tests at those potentials were used to construct a voltammogram trace which has the same trend as a normal cyclic voltammogram but with much lower current densities. INTRODUCTION As a result of the depletion of copper oxides, the leaching of copper sulphide minerals has become the focus of many studies. Chalcopyrite, (CuFeS2) which is the most abundant of copper minerals, has proved to be challenging to process via hydrometallurgy, mainly related to its refractory nature, slow kinetic rates of dissolution and the formation of an inhibiting product layer on its surface, during leaching.

Jan 1, 2019

By Terry J. Briggs, Ian J. Kelso

"Abstract- The Century mine in northwest Queensland,Australia, is a major sediment-hosted zinclead- silver orebody, located within the western Mount Isa Basin. Stratiform, carbonaceous shalehosted mineralization is developed within Proterozoic shale and siltstone sequences of the Lawn Hill Formation. CRA Exploration Pty Ltd (CRAE) discovered the Century deposit in 1990 and open pit mine development commenced in 1998 under the ownership of Pasminco Century Mine Limited (PCML). The deposit contains an identified mineral resource of 105 Mt @ 12.1% Zn + 1.7% Pb + 46 g/t Ag (Broadbent and Waltho, 1998) which is currently being mined at a rate of 5 Mt/y.In December 1998, an exothermic reaction was observed between explosives spilt onto shale drill cuttings from a blasthole. This reaction is referred to as ‘reactive ground’ and has the potential to cause premature detonation of explosives in a charged blasthole with catastrophic consequences. The incident led to a subsequent geological and geochemical assessment of the different rock types at the Century deposit and their potential reactivity with ammonium nitrate-based (AN) explosive products. This assessment was conducted in an attempt to characterize zones safe for blasting with uninhibited AN-based explosive products. A direct result of this study is a set of procedures outlining the use of different AN-based explosives in areas defined as potentially reactive or non-reactive for the different lithologies present. Black shales contained in both the waste and mineralized sequences contain the sulfide mineral pyrite (FeS2), which is thermodynamically unstable with AN contained in commonly used explosives. The potential reactivity of partially weathered pyrite can ultimately result in the decomposition of an AN-based explosive. It was determined that only pyritic black shales showed any potential to react with AN, irrespective of their position in the stratigraphic sequence. Other lithologies present at Century, including Proterozoic sandstone and Cambrian limestone, are classified as non-reactive with AN. This is a geological risk management situation present at the Century mine."

Jan 1, 2001

By Emilie Williams

The Mouska Mine uses primarily shrinkage mining to extract the narrow veins that contain its mineralization. Mining is currently occurring on levels 12 to 14, reaching depths of 800 m below surface. Although the mine is not considered ?deep?, no backfill is available to fill empty stopes and certain areas remain open for over 500 m in height. As only narrow sill pillars remain to separate the levels, a highstress environment is created. Seismic activity was first observed when mining reached Level 11 (600 m deep) and has steadily increased since then. Seismic activity is associated with the highly-stressed sill and rib pillars; no geological structures have demonstrated significant seismic potential to date. In response to this increase in activity, pillar dimensions have been increased with depth and dynamic ground support has been installed. Seismic and pressure monitoring have been implemented, among other types of instrumentation. The following paper further describes the challenges associated with using conventional methods in the high-stress environment typical of the Canadian Shield, as well as several solutions implemented to mitigate these risks.

Feb 1, 2008

By Zhigao Xu, Ruan Chi, Zhenyue Zhang, Yaoyang Ruan, Zhengyan He

Thorium is frequently the main radioactive element in rare earth ores and is a resource that can potentially substitute for uranium. Thorium must be separated from rare earths in order to obtain products with low radioactivity. There are abundant resources of thorium in the rare earth ores in China, especially in Baiyunebo mixed ores. As an associated element coexisting in rare earth ores, thorium is, or can be, separated from rare earth concentrate, iron concentrate, as well as from waste water and slag to achieve recovery of thorium. The methods of separation include ion exchange resin, liquid-liquid extraction, and liquid-solid extraction. TBP extraction has been the main method applied to separate thorium by domestic and foreign scholars. This paper presents a comparison of different processes for the separation of thorium from rare earth ores, especially Baiyunebo mixed ores, single bastnaesite and monazite ore, and provides suggestions for the future recovery of thorium resources.

Jan 1, 2014

By J. Brent Hiskey

At present, approximately 80 % of the worlds mine production of copper is achieved by smelting and electrorefining. The principle aim of copper electrorefining is to satisfy the large demand for extremely pure copper. It is remarkable that high quality copper cathodes with the required purity (99.99+% Cu, ASTM B115-10) and structural characteristics (i.e. deposit density and morphological texture) are produced from impure copper anodes dissolved in electrolytes containing a variety of impurities. This is accomplished with the proper control of operating parameters such as: current density; temperature; copper and sulfuric acid concentration; agitation; substrate preparation; and the application of electrolyte additives. The basic elements of the electrolysis of copper have not changed significantly over the past 150 years since the early developments of James Elkington. Importantly, our fundamental understanding of the underlying electrochemistry has advanced considerably. This is especially true regarding our knowledge of the mechanistic role of additives during the electrocrystallization of copper. This is a very complex subject and modern electrochemical techniques and the development of surface characterization and imaging instruments has helped immensely in our ultimate understanding of how additives control the deposit structure and morphology. The purpose of this paper is to review the historical development and application of electrolyte additives in copper electrorefining and to examine our current knowledge regarding their use. INTRODUCTION The first transatlantic telegraph cable was completed in August 1858. Regrettably, this cable failed shortly after the initial connections. After several more failed attempts, improvements in materials and copper quality resulted in successful communication between Europe and America on July 28, 1866. In many ways this hallmark event demonstrated the need for high purity copper. The first copper refinery in the world was commissioned in May 1869 in Pembrey, South Wales by partners Josiah Mason and James Balleney Elkington. (Historical Note). The 1865 and 1868 British patents issued to James Balleney Elkington were the foundation for the first commercial production of high purity electrolytic copper (Elkington, 1865, 1869, 1870). This important achievement was made possible primarily by the invention of the dynamo which was based on the fundamental operating principles advanced by Michael Faraday. A symbiotic relationship between copper refining and the dynamo was henceforth established. The dynamo provided electric current for electrolytic refining of copper and the electrorefining tankhouse provided pure copper which was required for the generation and transmission of electricity.

Jan 1, 2019

By R. D. Brown

In view of the many changes which have taken place since 1950 in the rules of the Income Tax Act concerning the deduction of exploration and development expenses, many corporate taxpayers each year face the tedious task of determining which particular rules their unclaimed exploration and development expenses are subject to and in what sequence these expenses are to be claimed. Recent amendments to the Act have cleared up some of the mystery of the "ordering" of these deductions. This article examines the sequence in which various categories of exploration and development expenses are to be deducted in accordance with the terms of the Act as amended by Bill C-11.

Jan 1, 1978

By Mark Richards

Highland Valley Copper is a large, open-pit copper mine in the southern interior of British Columbia. Reclamation has been in progress on the site since 1987. Some 6,300 hectares will have been disturbed at the end of the mine?s life, the majority of which will eventually be reclaimed. The establishment of vegetation and the development of a self-sustaining vegetative cover are the central components of the mine?s reclamation plan. The present vegetation-monitoring program for the reclaimed area represents a significant commitment of resources and only addresses a small portion of the site each year. In an effort to expand the area surveyed while improving the efficiency of the monitoring, the use of remote sensing is being investigated. Airborne multispectral imagery was acquired in the summer of 2001, and the results of the multispectral classification were compared to ground observations made during the routine 2000 and 2001 monitoring program. A thematic map with 17 vegetation classes was produced. Within the vegetation classes, there was a strong spectral separation between ? dry grasses? and ?legumes? with further separation according to their density. Green biomass could also be quantified remotely across a wide variety of vegetation types. During summer 2002, further aerial imagery was acquired in combination with a targeted ground-truthing program to determine characteristic vegetation types associated with recognized spectral signatures, which can be used in a supervised classification. It is anticipated that after some fine-tuning, it will be possible to shift the ground-sampling effort from areas where the aerial classification confidence is high to more complex areas.

May 1, 2003

By J. E. Lee

"This paper describes the current practices and experiences, and discusses design parameters concerning slurry pumping at Inco Metals Company in the Sudbury District. It deals mainly with the long tailing and concentrate lines. Subject matter is arranged under the following headings: pumps, lines, instrumentation, system design, operation.IntroductionThe Inco Metals Company is the mining and processing section of INCO LIMITED. In the Ontario Division, it operates 13 mines, 5 mills, a smelter, an iron ore plant and 3 refineries, all engaged in the mining and recovery of nickel and copper. This paper describes the slurry pumping practices in the mills of the Ontario Division.The PumpsWe have in our Sudbury area mills most of the available types of slurry pumps, in sizes from one inch up to twelve inches, a total of about 400 pumps. The rubber-lined, horizontal shaft pump is; most numerous. However, for certain applications, the hard-metal pump is essential, and is becoming more popular for general mill service. Two types of vertical shaft pumps are used. There are a few diaphragm pumps on small thickeners, but the larger thickeners have centrifugal pumps either directly connected to the under-flow or with one pump handling several gravity underflows. We have not used piston or plunger pumps in our mills."

Jan 1, 1978

By R. E. Whitehead

"The earliest gold-mining operations in Ontario included the Cordova, Deloro, and Sophia mines north of Lake Ontario (see for example, Miller and Knight, 1914). The Cordova deposit, worked intermittently between 1891 and 1940, is reported to have yielded 22 774 oz of gold from 127 670 tons of ore averaging 0.19 oz/ton Au (Gordon et al., 1979). The property remained inactive for many years. In 1988, Gunnar Gold Inc. and Mill City Gold Inc. conducted a drilling program along the main Cordova vein. The present study is based on core from three drill holes through the Cordova gabbro (Fig. 1) and the carbonate alteration zones enveloping the quartz-carbonate veins. The relatively narrow width of the alteration zone and the availability of continuous sections of core provided an opportunity to conduct a compact mineralogical-chemical study of carbonate alteration and its effect on the redistribution of rare earth elements (REEs). Although the Cordova deposit is not of great economic importance, this study has revealed a number of interesting features which are interpreted as resulting from processes that may be applicable to gold-bearing quartz vein deposits elsewhere.The Cordova gabbro is layered in places, varying from fine-to coarse-grained and in color from light gray (feldspathic) to dark gray-green (amphibolitic). However, layering within the section of the gabbro considered here and which hosts the Cordova gold deposit is mainly textural rather than compositional. Samples of unaltered gabbro selected for analyses were medium- to coarse-grained; amphibolitic and anorthositic phases were avoided as being less representative of the general chemical composition of the gabbro.The Cordova intrusion has undergone regional metamorphism and consists dominantly of actinolite and saussuritized plagioclase with smaller amounts of granular clinozoisite and flaky chlorite; minor quartz, ilmenite, titanite, apatite, and calcite are typically present. Some actinolite grains have irregular rims of pleochroic green hornblende that is optically continuous with the actinolite. Both chlorite and clinozoisite occur in two modes. Chlorite occurs as an alteration product of actinolite and as separate grains in the groundmass. Clinozoisite and albite occur together as regional metamorphic alteration products of original plagioclase crystals and as discrete grains in the matrix.The main gold-bearing quartz-carbonate occurrence occupies an easterly trending, steeply southward-dipping carbonatized shear zone up to 15 m wide and 700 m long. The gold occurs principally in irregular lenses and veins of quartz-carbonate up to a foot thick occupying the lower part of the schistose shear zone within the gabbro. This zone consists of chlorite, biotite, and carbonate and is flanked on both sides by chlorite-carbonate schist lacking biotite. The chlorite-carbonate schist in turn grades into regionally metamorphosed actinolite-bearing undeformed gabbro.The dominant sulfide within the quartz-carbonate lenses and in the surrounding schist is pyrite which occurs mainly as small cubes (1 mm to 2 mm) generally making up less than 10% of the rock. Rare blebs of chalcopyrite are present. Magnetite is common throughout the schist."

Jan 1, 2001

By M. P. Rennick, D. M. Burton

The Murray Brook massive sulfide deposit, which was the first geochemical discovery in the Bathurst camp, is one of the largest sulfide deposits in the area. The massive sulfides are hosted by quartzose metasedimentary rocks in the lower part of the Ordovician Tetagouche Group. This thick succession of sedimentary rocks is overlain conformably by felsic volcanic rocks, and is structurally overlain by mafic volcanic rocks. The massive-sulfide body is polydeformed, but primary metal zoning is still discernable and may permit future exploitation of discrete lead-zinc and copper zones. Although it was discovered in 1956, the deposit was not developed until 1989, when Murray Brook Resources commenced processing of gossan containing precious metals. Recovery of gold, silver, and mercury is accomplished by indoor vat leaching on a year-round basis.

Jan 1, 1992

By Darrell McClarty, Roger Payne, Matt Haggis, Michael Courtin, Deborah Berthelot

"Over forty years of uranium mining in the Elliot Lake region of Ontario (I 956-1996) has resulted in the production of over 300 million pounds of uranium. With the completion of mining activity, Rio Algom Limited and Denison Mines Limited are utilizing progressive environmental technologies and management systems to reduce and manage the environmental risks associated with the 150 million tonnes of potentially acid-generating tailings in nine regional waste management areas. Water covers designed to reduce oxygen entry and thereby significantly inhibit acid generation have been applied at six of the sites with the Quirke site serving as a demonstration site for the Mine Environmental Neutral Drainage program. All five of Rio Algom Limited' s effluent treatment plants are monitored and controlled from a central control station utilizing a Supervisory Control and Data Acquisition (SCADA) system based on ""Fix Dmacs"" technology. Scheduling, auditing and reporting of plant operating and environmental monitoring programs for the entire watershed are controlled utilizing the Regional Environmental Information Management System (REIMS). Proper application of these technologies and management systems facilitates delivery of cost-effective environmental monitoring, care and maintenance programs at these sites and provides tools to demonstrate compliance with all environmental performance criteria.IntroductionCost-effective management of multiple tailings management areas distributed throughout a 35 km watershed requires the application of leading-edge environmental technologies. Long-term monitoring, care and maintenance costs must first be minimized through the application of decommissioning technologies that inhibit acid generation and minimize the release of contaminants from the sites. On-going operating costs must then be controlled through the application of environmental management strategies that optimize the allocation of resources while ensuring compliance with regulatory and Company environmental requirements.Using sites in the Serpent River Watershed as an example, this paper demonstrates the effectiveness of water covers as a decommissioning strategy to inhibit acid generation. In addition, the Telemetered Environmental Operating Control System and Regional Environmental Information Management System are reviewed as examples of the application of environmental technologies to the management of environmental programs."

Jan 1, 1998

By Edmond Chow

Shovel bucket blast fragmentation analysis is an alternate way to assess blast performance and its effects on downstream mining processes. A camera is installed on the boom of cable shovels, and the stick of hydraulic shovels. Images are captured automatically as the shovel digs, and are processed to acquire rock size information. The automatic data acquisition makes this method safe to use with minimal manual labour. It also allows for a large set of sample data to be captured from both the surface and the interior of a bench face. The system has been deployed in several mines to provide an objective assessment of blasting performance. Images are captured from their cable or hydraulic shovels. The images are grouped into sets based on the shovel location and time to match the fragmentation to specific blasts. Blast fragmentation reports are created for each blast after reviewing the results. Measuring blast fragmentation from the shovel bucket proves to be an effective alternative for blast performance assessment with unique advantages. The blast fragmentation information has been valuable to the mines, and the mines have begun adopting it into their operations.

May 1, 2011

By M. B. McClenaghan

"The Ontario Geological Survey completed a regional till sampling project between 1984 and 1988 in the Black River Matheson (BRiM) area of northeastern Ontario. The project was designed to aid mineral exploration in the area by documenting the Quaternary stratigraphy and by providing a database of till geochemistry. This paper summarizes the results from the sonic overburden drilling component of the BRiM project carried out in areas of thick drift (> 5 m). Results from till sampling in areas of thinner drift (<5 m) have been presented in a separate paper. Approximately 1100 till samples were collected from 225 sonic drill holes. For each sample, the non-magnetic heavy mineral (>3.3 S.G.) and fine (-250 mesh) till fractions were analyzed geochemically and visible gold grains were recovered by panning.Gold and other multielement geochemical data were plotted using proportional symbols to highlight anomalous areas and to demonstrate how to evaluate and interpret a very large geochemical dataset. Thresholds for identifying anomalous concentrations of Au in till samples, defined using the 95th percentile, are 1500 ppb and 12 ppb for the heavy mineral and fine fractions, respectively. The heavy mineral fraction of older ti1ls and to a lesser extent, Matheson Till, display a number of significant gold anomalies in the study area, which in a few cases, are associated with base metal anomalies. The vertical position of gold anomalies in Matheson and older ti1ls varies from directly on bedrock to several meters above the bedrock surface and can provide information of relative ice transport distances."

Jan 1, 1994

By Z. D. Hora

Commercial production of barite commenced in British Columbia in 1940; shipments have been recorded from ten deposits, of which four are particularly significant: The Brisco, Silver Giant, Parson, and Mineral King mines. Parr of the barite production is a by-product of base metal deposits in which barite is a major gangue mineral. About one hundred occurrences are known. COMMERCIAL production of barite in British Columbia dates back to 1940. Production volumes rose and fell and reached 39,900 tonnes in 1972. The main producer is Mountain Minerals Limited . There are two principal areas of barite deposits in British Columbia: ( I) The southeast part of the province along the Rocky Mountain Trench , which is the source of all production to date. (2) Stratabound occurrences in northeast British Columbia in the Gataga-Ketchika rivers and Muncho Lake areas which are not yet developed. Of the approximately one hundred reported barite occurrences, only ten have recorded commercial shipments, some of insignificant amount. So far, four deposits have proved to be important producers: Brisco, Silver Giant, Parson and Mineral King. The Mineral King property is situated near the confluence of Toby and Jumbo Creeks, 35 km southwest of lnvermere. The lead-zinc-copper-iron-barite deposits, as described by Fyles (1959, 1962), replace Proterozoic Mount Nelson dolomites of the Purcell system on the limb in the trough of a complex, tight syncline. The mine operated from 1954 to 1967 and 2,097,900 tonnes of baritic ore that was processed for base metal concentrates and also produced 22,680 tonnes of by-product barite. Since 1970, some 136,000 tonnes of barite have been recovered from the old tailings pond. The deposit is now considered depleted. The Silver Giant mine is located 10 km northwest of Spillimacheen. Barite and lead-zinc sulphides replace Cambrian Jubilee limestone near their contact with the overlying Ordovician McKay slate. Mineralization is located in the nose of an overturned plunging anticline. Between 1951 and 1957 800,000 tonnes of baritic ore were processed for lead and zinc concentrate. After 1959 barite was also produced , first from open pit, and later from reworked tailings. Up to 1979 production of barite totalled approximately 180,000 tonnes. Two other producing mines in the area are descri bed by G.R. Manson (this volume). Large, bedded stratabound barite deposits are reported from northeastern British Columbia. Six major shale-hosted Industrial Minerals in Canada lead-zinc-barite occurrences are known in the Devonian Gunsteel Formation. These are: Driftpi le Creek, Mount Alcock, Cirque, Pie, Fluke and Elf. In addition, numerous occurrences of strati form blebby or nodular barite and locally massive white crystalline barite are known from the Driftpi le Creek and Ak ie River districts in Gunsteel shale and from the Kechika, Road River and Ware map areas from Silurian siltstone . The size of these deposits is impressive; the baritic horizon at Mount Alcock is reported to be 25 to 30 m thick , and dri ll ing results from the Cirque deposit indicate reserves of 30 mi llion tonnes of baritic lead-zi nc-si lver ore. Similar bedded barite deposits are also reported from Midway area, near the Yukon border.

Jan 1, 1984

By Garry Biles, Ken Major, Raj Anand

"Prime Resources Group Inc. (Prime) commenced the Eskay Creek Mine operations in 1994 in northern British Columbia. The ore from the underground mine is crushed and shipped to smelters in Japan and Canada. The nominal production rate is 300 tonnes per day.Before commencing the above operations, preliminary evaluations for the high grade gold mine had indicated that an extremely complex metallurgical and chemical process flowsheet would be required to recover the economic metals. Subsequent to the metallurgical testing program, Prime identified markets for the untreated ore and initiated underground mining and ore transportation operations.Prime recently identified lower grade ore zones, which are less economic or uneconomic to mine and ship directly to the smelters. Test programs were initiated to evaluate processes for upgrading the ore to a marketable product. In 1997, Prime will complete the engineering and construction of a 150 tonne per day flotation plant to concentrate the gold and silver values for the NEX and 109 zones. The mine will then, in addition to the direct shipping of the shippable ore, ship concentrate from the millable ore. This paper discusses the development and design of the flotation plant.IntroductionThe Eskay Creek Mine is located in north-western British Columbia approximately 83 km north-west of Stewart, B.C. as shown in the location map Figure 1. Access to the site is provided by a restricted access gravel road from Bob Quinn Lake junction of highway 37, a distance of about 59 km. The work force at the mine is based on a two-week rotation schedule. Employees are flown from as far away as Vancouver to Smithers by commercial airlines and then from Smithers to the Bob Quinn airstrip by local charter. During poor weather conditions, transportation to site is by vans that take about six hours to travel the 450 km road distance."

Jan 1, 1998

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By Robert B. Parsons

"Finance Minister Paul Martin&apos;s first budget disappointed almost everyone. The business sector was disappointed at the some what feeble attempt to grapple with the country&apos;s deficit. The mining industry was disappointed by tax proposals regarding mine reclamation that fall short of the industry&apos;s needs. Has anybody been happy with a federal budget? Federal Budget DisappointsThe federal government&apos;s budget papers that were tabled on February 22, 1994, contained a rather bizarre mixture of unrelated tax proposals. The budget signals an unexpected attack on the tax treatment of debt settlements, on certain types of corporate reorgani2ations, and on income earned by foreign affiliates. This is an old style budget, which proposes a pot pourri of technical changes and policy initiatives. Mine ReclamationEffective February 23, 1994, a taxpayer&apos;s contributions to a prescribed mine reclamation trust fund will be deductible as a current expense. The budget papers do not provide a definition of what will constitute a ""prescribed"" trust: this definition will surface in due course. However, the budget papers indicate that:• income earned in such trusts will be subject to tax each year;• all withdrawals from the trust (including income already taxed) will be included in computing the income for tax purposes of the recipient;• reclamation costs will continue to be fully deductible at the time incurred; and • contributions, trust earnings, and withdrawals will not be taken into account for the purposes of determining a taxpayer&apos;s resource allowance."

Jan 1, 1994

By Daniel Hodouin, Mélanie Proulx, Claude Bazin

"Collector and frother are commonly used to induce the floatability of valuable minerals in flotation plants. These reagents are usually distributed down a flotation bank or sometimes added in a single location at the top of the bank. A review of the literature and some experimental results obtained from laboratory and full scale trials indicate that the way flotation reagents are distributed down a flotation bank may influence the flotation response of coarse particles. The paper summarizes these observations which show that the distribution of reagents is a potential tuning variable for process optimization.IntroductionFlotation is in many cases the only way to concentrate sulphide and some oxide minerals. Flotation is a concentration process that uses particle surface composition to induce the selectivity by mean of hydrophobic reagents. The influence of particle size on flotation was firstly analyzed in the 50's1·2 and intensively investigated in the 70's, early 80's and 90's3-18. Most of the observed results show the existence of an optimum flotation size range9 whose recovery is not significantly influenced by a reduction of collector dosage""18. This result brought the idea of using a small portion of the total collector dosage at the top of a rougher bank and to distribute the remaining through the end of the bank to ensure sufficient collection of the coarse particles that need more hydrophobic coverage to attach to air bubbles and be lifted to the surface.This paper discusses the idea of using the distribution of reagents down a flotation bank to tune the operation of the process. Unlike the literature on the effect of reagents (collectors, frother...) dosage that is dense, little attention has been put on the distribution of reagents in a flotation bank. Although research on this subject has not been pushed very far, some operators have recognized the potential of a strategic addition of reagents down a flotation bank19. Except for a few exceptions, the proportions of the reagents to be distributed down a flotation bank are decided according to operator's experience instead of process analysis in relationships with particle size. This paper recalls observations made by different researchers that lead to the idea of using the distribution of reagents as a tuning variable for the flotation process. The paper does not present a detailed analysis or optimization scheme for tuning the distribution of reagents, but analyzes some plant and laboratory results with a view toward the development of a testing methodology and ultimately a validation or rejection of the idea."

Jan 1, 1998

By Angela L. Paveley

Economic viability of base metal mining is complicated by a volatile market that can cause fluctuations in the growth and stability of the mining industry. Nickel is mined primarily for use in manufacturing industrial stainless steel and plating materials. It is essential that nickel production be sufficient to respond to current and future market demand. A Post-Pillar cut and fill mining complex is currently producing nickel sulfide in Northern Manitoba. From 2006 this area has shown a steady increase in the annual production, rising from 11 million pounds to 25 million pounds in 2010, and accounting for 33% of the total production for the Manitoba Operations. It is expected that fine-tuning the mining process can safely enhance ore recovery, improve production consistency, and increase economic viability of the deposit. The Post-Pillar Optimization study was initiated by the local technical and operational departments at the mine and analyzed from July 2010 to March 2011. The purpose of this study was to determine if portions of non-recoverable pillars can be slashed without jeopardizing pillar strength. This ideal case would optimize ore recovery and reduce variability in the ore mining rate. Numerical modeling and geo-mechanical material properties analyses, completed by the rock mechanics group, define the maximum drift width at 32 feet and the minimum pillar width at 18 feet. Thus, it was suggested that up to 3 feet could be slashed from two sides of the standard 24 foot pillars without damaging ground integrity. The field data collected indicates that additional ore could be recovered without compromising the safety of the workplace and the integrity of the complex. Consequently, technical and operational groups work jointly to achieve pillar optimization. Approximately 500,000 pounds of nickel was extracted from the complex via pillar optimization from July 2010 to March 2011. Economic analyses show the pillar optimization method developed for the mining complex is a proven, value-added opportunity. The mining complex remains a safe workplace and has retained ground integrity.

Nov 1, 2011

By David F. Machuca-Mory

Modelling the geometry of a vein is a crucial step in resources estimation. The resulting models are used as mineralization domain boundaries and have a direct impact on the tonnage of estimated resources. Deterministic models are often built using time consuming wireframing techniques usually based on hand interpretation of the drillhole intercepts. Another approach consists in coding the drillhole samples by a function of their distance to the veins contacts. The coding is subsequently used for modelling the vein contacts away from drillholes. This is a more efficient approach and is able to provide a measure of tonnage uncertainty. The use of location-dependent variograms improves the modelling by incorporating local changes in the anisotropy of the vein structure. This combined approach results in more realistic vein models, particularly when the geometry of the vein has been are altered by folding, shearing and other structural processes. The approach is illustrated on a realistic case study.

Oct 1, 2009