Search Documents

By Li. L.

Backfilling has become a popular solution in underground mines around the world. It reduces environmental impact of mining industry and improves ground stability. In most cases, backfill has a high water content so that it can be delivered by pipes from a backfill plant on ground surface to underground stopes. Upon deposition in the stope, the backfill tends to consolidate under its own weight, leading to a generation of excess pore-water pressure. To avoid excessive pressure and protect the backfill barricade installed at the base of the stope, the backfilling of the stopes is usually divided into two stages: plug pour and backfill body pour. The interruption of backfilling operation is undesirable as it slowdowns the mining productivity, and sometimes causes pipe clogging, leading to unexpected increase in manpower cost and further reduction in mining productivity. The backfilling interruption time may be reduced, even eliminated if the drainage of backfilled stopes is sufficiently improved. This paper presents an application of wick drains, a material commonly used in civil engineering, to mine backfilled stopes to help accelerating the drainage. A protocol is proposed for installing the wick drains in a mine stope to be backfilled. Numerical simulations were made, showing that the drainage of the backfill can significantly be improved by the introduction of wick drains. The application of wick drains in mine backfill can thus be considered as a promising technique and merits deeper and more detailed investigation.

Aug 1, 2013

By Zoltan Hajnal

Magnetic studies have been carried out on 88 surface and 157 underground samples from the Coronation Mine area of northern Saskatchewan. The intensity of the surface samples was compared to trace element determinations from the same locality. A good correlation was found between the titaniferous constituent of the rocks and the intensity of magnetization. From the direction of the remanent magnetism, two virtual geomagnetic poles were determined -latitude 12° 54' North, longitude 158" 17' West; and latitude 23" 42' North, longitude 163° 45' West. The sulphide ore specimens showed anisotropic susceptibility characteristics. A relationship was found between the measured maximum susceptibility values of the ore specimens and the direction of the tectonic forces which are considered to have formed the structure at the Coronation mine. Introduction T HIS paper summarizes the results of a study of the magnetic properties of samples from well-known Precambrian formations. The observed data give information for an interpretation of the magnetic field conditions in Precambrian times. The high magnetic intensity values indicate the importance of the study

Jan 1, 1965

By T. D. Brown

"A review of the current status of gasification technology shows that many engineering systems are immediately available for use in the gasification of coal. Widespread international experience can be brought to bear on the atmospheric pressure gasification of all Canadian coals.Unless a high ash content dictates the use of a fluid-bed gasifier, it appears that bituminous coals can be used in gravitating (fixed] bed systems and that the strongly caking coals are most suited to the high-pressure entrained-bed systems . Existing and developing technologies in fluid-bed gasification are attractive for reactive lignites and subbituminous coals.The Fischer-Tropsch based process is the only commercial embodiment of coal liquefaction; the use of Canadian coals in this process depends only on their gasification characteristics. Current developments in hydroliquefaction are directed toward carboniferous coals of medium or high rank. It is not clear that cretaceous coals of the same rank will give similar process yields and economics.IntroductionThe twin coal conversion processes of gasification and liquefaction have a history which dates back beyond the current energy shortages of the western world. Indeed, liquids and gas from coal were produced before this century.Coal gas produced from a coal carbonization process was originated before 1800, and the development of gasification of non-coking coals was patented by Siemens in 1860.This patent represented the first use of air and steam together in the gasmaking process. The pioneering development of coal gasification Using oxygen and steam was demonstrated by Lurgi in the late 1920s. This historical sequence was all carried out at atmospheric pressure, and it was not until the immediate pre-war (1939/45) years that operation of the coal gasification process at elevated pressure became a reality."

Jan 1, 1981

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005

By N. Erarslan, M. Ghamgosar

With the increased use of mechanized rock excavation, there have been developed internationally a number of methods to assess the abrasivity of rock materials. These methods range from determination of abrasive and hard mineral content using petrographic thin section analysis to weight loss or rate of wear flat development on specified test pieces. The Cerchar abrasivity index (CAI) test has been widely accepted for the assessment of rock abrasiveness and is determined as the abrasion of a steel pin after scratching over the freshly-broken or saw-cut surface of a rock. Two types of testing devices are in use today: (i) the original ‘Cerchar apparatus’, and (ii) the ‘West apparatus’, which was adopted herein. The CAI is calculated from the measured diameter of the resulting wear flat on the steel pin after 10mm scratching. This test has been considered to provide a reliable indication of rock abrasiveness for isotropic rocks. However, a great amount of rocks in natureis anisotropic. Phyllite is an anisotropic and foliated metamorphic rock and various types of phyllite specimens were tested in this research. Although phyllite is a type of rock primarily composed of quartz and the expected CAI value can be high, mechanical cutting of this rock should not be very problematic compared with igneous rocks have same CAI value. As phyllite is a foliated metamorphic rock, most of the specimens split into sheets through the quartz seam by the tip during scratching normal to the axis of quartz seams. Hence, viability assessment of Cerchar abrasivity test and F-Schimazek index values for the anisotropic rocks is investigated in this research.

Jan 1, 2015

By Xueyi Guo

The total production of nonferrous metals in China is 31.35 million tons in 2010, which ranks first in the world for the past ten years. Large quantities of solid wastes including slag, residue, ash, and dust are produced every year in the production of nonferrous metals. These secondary resources are renewable, not only contain abundant valuable metals which can be recycled by metallurgical processing, but also could eliminate the pollution to the environment. In this paper, the status quo of the main nonferrous metals recycling in metallurgical industries in China was summarized, and the future development of waste processing and resource recycling was prospected.

Jan 1, 2011

By Sarah R. Hindle

Carbon capture and storage has jumped to the forefront of climate change mitigation efforts for its capacity to sequester large amounts of carbon. Mineral carbonation is one prominent option, mimicking and accelerating the natural weathering process of certain silicate minerals. This has the ability to produce stable carbonate minerals that can store carbon on geologic time scales with little to no risk of leakage. Commercialization of this process is ideally suited for integration into the proposed mining operations at the Turnagain Nickel site in Northern BC. This is due to the abundant supply of suitable ultramafic feedstock material, as well as the economic benefit of sharing costs while reducing net emissions and bringing value to otherwise valueless and costly waste rock. While studies have shown this process to be technologically viable on a laboratory scale, assessing the economic and financial viability of such a process on an industrial scale is necessary. An evaluation of the financial feasibility of integrating mineral carbonation into the mining cycle at Turnagain under a proposed cap-and-trade system is presented.

May 1, 2010

By A. Chieregato, C. G. Oñate Salazar, D. Martinelli, D. Peila, M. Barbero

This paper is aimed to confirm the possibility to excavate fractured rock masses by using EPB shields, even in presence of relevant water tables. This verification is based on laboratory test experiences carried out at TUSC laboratory of Politecnico di Torino, where the natural material is tested in order to verify the suitability of a certain conditioning technique in particular conditions. This is due to the fact that every case should be studied apart from existing studies on a certain rock type, as other factors such as fragmentation of the rock mass, natural water content and porosity of the rock can considerably influence the final result of the conditioning process. The most important aspects that allow to consider the conditioning of fractured rock masses as suitable are: possibility to create a plastic paste that can transmit the pressure at the front in a effective way; reduce the permeability of the spoil material in order to reduce the possibility of water leakage inside the chamber and eventually in the tunnel; verify the consistency of the conditioned material for the extraction through the screw conveyors and the belt conveyors. For this research an argillitic schistose rock mass, with some quartzitic and calcareous inclusions, has been studied by using different level of conditioning in order to verify the suitability of an eventual EPB excavation through this formation.

Jan 1, 2015

By D. W. Li

Due to the ultrasonic testing and mechanical wind speed sensor have high requirement for the environmental of the coal mine, the charge induction wind speed detection method based on wavelet analysis is proposed. The same wavelet disturbance detection method is used at a fixed distance to obtain an induction signal to obtain a pass time, and then calculate the magnitude and speed of the wind. Simulation and verification experiments show that the method has application across a wide range of test speeds (up to 60 m/s). The metal probe causes little pipeline flow field interference. The method is particularly well-suited to dusty environment, and does not cause dust deposition through long-term operation. It can be widely used in coal mines for point wind speed continuous online testing.

Aug 1, 2013

By Zhiqing Zhang, Changyun Chen, Qing Liu, Lin Lin, Zhihong Jia, Guangjie Huang, Lipeng Ding

The effect of interrupted quenching (IQ) treatments on natural aging and bake hardening response of Al-Mg-Si alloy was investigated by hardness measurements, tensile test, differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The results show that interrupted quenching at 100oC could effectively suppress natural aging and improve bake hardening response. The optimized interrupted quenching treatment is 100oC for 45min, which gives the alloy a relatively low T4 temper strength and higher bake hardening response. The formation of highly dense cluster(2) during the interrupted quenching could be the reason for suppressing the natural aging and accelerating the precipitation of ß? phase during the paint bake treatment. In addition, interrupted quenching at higher temperature (170oC) results in unfavorable properties in both T4 temper and paint bake treatment. The formation of large precipitates is responsible for these undesired effects.

Jan 1, 2015

By C. Y. Lim, H. W. Kim, M. S. Kim, J. H. Cho, Y. S. Lee

Al - 5.5 wt% Mg - 0.3 wt% Cu alloy strip was successfully fabricated by horizontal-type twinroll casting (TRC). For producing sound strips with no surface defect, the casting was conducted at various roll rotation speed, and the sound strip could be obtained at relatively low casting speed (3 rpm). The cast strip was homogenized at 450 °C for 10 hours, and then cold rolled with a reduction rate of 78%, followed by a final annealing at 450 °C for 1 hour. The annealed sheets showed good mechanical properties with approximately 330 MPa in tensile strength and 27 % in elongation, but exhibited strong anisotropy depending on the tensile directions. For the homogenized sheets, warm rolling was also conducted at 200, 300, and 400 °C. The tensile test results of the warm-rolled sheets showed that the rolling at medium temperature (300 °C) was proper to fabricate the sheets with relatively good mechanical properties and low anisotropy.

Jan 1, 2014

By J. Boulton

"Nuclear energy is an established and proven energy source. Today, CANDU-PHW nuclear-electric generating stations produce over one third of Ontario's total electrical supply: safely and economically. In many parts of Canada, where economic hydro resources do not exist or are fully developed, coal and nuclear energy are the only alternatives for future large-scale electrical generating capacity.Recent analyses have suggested that, in the f ace of increasing energy demands and decreasing reserves of hydrocarbon fuels, Canada must depend on electricity to provide an expanded fraction of its energy budget. Nuclear energy is likely to play an increasing role in the generation of electricity; there are also potential applications as a supplier of process heat in industry and in the in-situ recovery of bitumen fro m tar sands.The future supply of nuclear fuel, reactor safety and radioactive waste management are briefly discussed. In each case, the benefits to be gained from a controlled expansion in the use of nuclear energy outweigh any uncertainties which may exist."

Jan 1, 1981

By B. S. Ignasiak, B. N. Nandi, D. S. Montgomery

The growing need to measure the extent of weathering of coking coal in storage and in transit prompted the comparison of the dilatation of coking coal on heating, which is known to be a sensitive index of oxidation, with the composition and volume of the gases produced by a mild pyrolysis of the same coal. It was found that the pyrolysis method had the advantage in that it could be used to study coking coals in advanced stages of oxidation, when the swelling properties had been largely destroyed. Of the various constituents in the pyrolysis gas, the most sensitive indication of coal oxidation was the volume of carbon monoxide evolved per gram of coal. For the coals examined, this index appeared to be at its best when the temperature of pyrolysis was approximately 35oC.

Jan 1, 1970

By J. C. Heaslip

Introduction The greatest single advance in rock drilling practice since the advent of percussion drills was the introduction of tungsten carbide tipped rock drill?bits. The evolution of rock drills has been a long and highly diversified effort which has culminated in the highly refined ?drilling machines we know today, but because of the spectacular possibilities shown by ?detachable bits, and especially those with tungsten carbide inserts, there is little doubt that the cutting face of .the drilling unit has in recent days stolen the spotlight of rock drilling research and commanded the major attention of the rock drilling fraternity. "Solid" Steels Until about twenty years ago, all rock was drilled with a one-piece rod with a bit forged on one end. In the early years of the art of rock drilling, there was tried every conceivable pattern of :bit from the single-edge chisel to elaborate geometric 'designs. In the end, it was found that a 4-point bit with two sharpened cutting edges crossing each other at right angles would serve best for most rock drilling requirements. For some years thereafter, the main concern of drill manufacturers was .to obtain the best possible steel for drill rods. This was not accomplished as easily as might be thought. The cutting end had to be such that it could be hardened sufficiently to do its work without premature dulling and yet not so brittle as to shatter under the multiple impacts.

Jan 1, 1951

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

By J. Gebhardt, D. McBride, C. R. Bennett, Croft. N., M. Cross

A comprehensive model of solution flow through heap leach systems requires a numerical solution with the ability to predict variably saturated-unsaturated flow through porous media domains that contain materials with spatially variable properties. The types of flow associated with stockpile leach processes lead to flow problems, such as infiltration into dry soil, drainage, perched water tables and flow through heterogeneous materials. Computational methods for modelling this class of flow behaviour are conventionally based on the classical Richards' equation. However, the governing equations are highly non-linear, difficult to solve, and require iterative numerical solution methods. The pressure-based form of the Richards' equation suffers from poor mass balance, while the mixed form can possess convergence difficulties. An adaptive transformed mixed algorithm is described, which reduces the non-linearity of the problem, optimizes the time step size, and provides a fast, numerically robust scheme that significantly reduces computation (or CPU) time. This method is shown to give fast, accurate solutions on a number of complex flow problems. The utility of this algorithm is illustrated through its implementation within the PHYSICA computational modelling software, which incidentally, provides a framework for a comprehensive heap leach model.

Jan 1, 2005

By Graeme G. Strathdee

"IntroductionThis paper presents an overview of the industry status, describes current potash industry practices at three mills, and summarizes developments that have taken place since the previous review by Banks (1985).The commodity potash is produced in both New Brunswick and Saskatchewan from the evaporite ore sylvinite. This ore is a mixture of co-crystallized halite, NaCl, and sylvite, KCl, and a minor assortment of silica, carbonate, sulphate, and clay minerals. Carnallite, KMgCl3.6H20, is also dispersed throughout the bedded deposits and can affect the recovery of sylvite for fertilizer and industrial uses.Canada continues to be a principal source of supply of agricultural and industrial potash products. Figure 1 shows the sector performance between 1989 and 1997 in the context of the world supply and demand situation as reported by Prud'homme (1997) of Natural Resources Canada.Potash industry output is traditionally measured as the quantity of potassium nutrient and reported as tonnes ofK20. Mineralogically, the principal form of potash produced in Canada is sylvite, KCl, and 1 nutrient tonne K20 corresponds to approximately 1.64 tonnes of sylvite of agricultural grade, about 95% KCI. In 1997, the Canadian industry milling capacity was 13.4 million metric tons (Mt) ofK20 (22 Mt KCl) while the actual production was 9.0 Mt K20 (14.8 Mt KCl). Worldwide milling capacity in 1997 was 35.9 Mt K20 (58.8 Mt KCl) and global consumption was 25.3 Mt K20 (41.6 Mt KCl). Canadian producers can deliver about 35% of the global demand for potash commodities"

Jan 1, 2000

By Isabel F. Barton, J. Brent Hiskey

Chalcopyrite (CuFeS2) is the earth’s most abundant copper ore mineral, but is refractory to leaching with sulfates, chlorides, and other common lixiviants and oxidants. This has led to increasing research into alternative lixiviants for recovering Cu from chalcopyrite. Here, we review the leach kinetics of chalcopyrite in glycine, ionic liquids, and methanesulfonic acid, compared to baseline ferric sulfate and ferric chloride. Glycine (CH2NH2COOH) has long been used in applications such as biocatalysis and electroplating, and has recently been examined as a lixiviant for whole ores and concentrates of both copper and gold. It is nontoxic, biodegradable, and capable of strongly complexing Cu2+. Compatible oxidants are peroxide, dissolved oxygen, and ferric sulfate. Chalcopyrite leaching rate in glycine is chemical reaction-controlled, but the effects of grain size and the reaction orders with respect to lixiviant and oxidant concentrations and mass transfer vary. The use of ionic liquids as a leaching agent for chalcopyrite has been extensively investigated in recent years. This system is based primarily on the use of the imidazolium molecule (C3H5N2), which is a planar 5-member ring structure. This lixiviant has been applied to the leaching of chalcopyrite in the form of pure mineral, concentrates, and ores. Kinetics of ionic liquid leaching of chalcopyrite vary substantially depending on the type and concentration of ionic liquid. Methanesulfonic acid (HCH3SO3) is one of the newest lixiviants available in leaching, having only been examined in the last decade. It has been examined as a substitute for sulfuric acid, since it is less corrosive, is biodegradable, and breaks down to carbon dioxide and sulfate over time. The rate of copper leaching from chalcopyrite by methanesulfonic acid is controlled by diffusion and exhibits a strong dependence on oxidant type and concentration. Despite promising reaction rates and total extraction by some of these novel lixiviants, comparison with baseline ferric sulfate and ferric chloride systems makes it doubtful that any will be commercially viable in the near term. Only at very high reagent concentrations and temperatures, and/or very fine grain size, did any of the systems perform comparably to the much cheaper ferric chloride at extracting Cu from chalcopyrite. Most had similar overall reaction rates and total extraction to ferric sulfate, which is relatively common and cheap. However, the leaching kinetics of these novel lixiviants offer valuable insight into the dissolution behavior of chalcopyrite in various systems.

Jan 1, 2019

By Liu Yulin, Zhao Yi, Tan Qi, Liu Lei

"Hydrotalcite is one kind of layered double hydroxides, and has special crystal chemical characteristics. Due to its good thermal stability, hydrotalcite used as the PVC heat stablier has attracted scientists’ attention. In this study, nano-hydrotalcite was synthesized by the method of mechanochemistry/crystallization, using brucite, Al(OH)3 and Na2CO3 as raw materials, and added into PVC to investigate the effect of hydrotalcite on thermal stability of composites. The synthesis mechanism was suggested by virtue of XRD, FE-SEM, FT-IR. It has been indicated that at the first of dry milling process, the parical sizes of brucite and Al(OH)3 decrease, while specific surface areas of them increase by the action of mechanical force, until produced amorphous particles. In the process of wet milling, metal ions in the amorphous body, which has high surface energy, can easily react with H2O, and produce the precursor of Mg6Al2(OH)18•4.5H2O, which has the same crystal structure as hydrotalcite. Under the hydrothermal condition, anions of OH- in the interlamination of precursor are exchanged by CO32- in the solution and nano-hydrotalcite is generated at last. The thermal stability was characterized by Congo red method. The results have revealed that hydrotalcite is one kind of long-term heat stabilizer, and residual stability time increase with the rise of added hydrotalcite amounts.INTRODUCTIONHydrotalcite, one kind of anionic clays, has been attracted a great interest for researchers because of their unexpected physical and chemical properties. The general formula is Mg6Al2(OH)16CO3·4H2O, where Mg2+ and Al3+ occupy octahedral positions in the brucite-like layers, and CO32- is an interlayer anion (Hoyo, 2007). Hydrotalcite is widely used in the fields of chemical engineering, materials engineering, environmental protection, medicine, and so forth, owing to its unique capability of adsorbability, ion exchange and thermal stability (Rozov, Berner, & Taviot-Gueho, 2010; Iwasaki, Yoshii, & Nakamura, 2012; Ay, Zümreoglu-Karan, & Temel, 2011; Cavani, Trifiro, & Vaccari, 1991; Li & Duan, 2005; Lin, Wang, & Evans, 2006). As a result, the study on synthesis and application of hydrotalcite has received considerable attentions."

Jan 1, 2016

By James H. Savory

"In recent years, there has become a growing interest toward a better understanding of balance rope behaviour. With this in mind, the auth or will present a comprehensive summary of field experience, as well as conclusions. In presenting this overview, it is the intent to stimulate further interest as well as provide a framework from which further in-depth investigation can be initiated.Topics which will be covered include rope cores, lubrication practices, loop dividers, rope failures, etc.IntroductionThe first friction hoist was designed in Belgium in J862 by Lemielle. However, it was not until 1877 when Carl Frederich Koepe installed a friction winder sheave at the Hanover Colliery in Germany, that the design was given serious consideration. The winder consisted of a motor-powered sheave over which a single rope was installed, and the end s attached to two conveyance s. Beneath the conveyances a rope was connected, designed to reduce the chance of slip. This was the first balance rope.This earl y mod el is a far cry from the modern tower or ground mounted Koepe winders employed throughout the mining industry today. There have been vast improvements in all aspects of the Koepe winders. One such improvement is in the balance ropes used. This particular area will be concentrated on, with emphasis on selection, maintenance and field experience.SelectionThe sale purpose o f a balance rope is to counter the head rope weight. Obviously then, in selection o f balance ropes, weight is of primary concern. Usually the head and balance ropes are equal in weight. However, sometimes balance ropes which are 5 to 10070 heavier than the head ropes are employed. These reduce horsepower demands during peak acceleration periods, and assist in overcoming inertia during retardation periods. As well, it is sometimes preferred to reduce the balance rope weight, in order to compensate for the eventual weight buildup of lubricant, dirt and debris."

Jan 1, 1983