Search Documents

By T. Beamish, I. Vasilev, T. Nikolov, E. Marinov, D. Kirilov, P. Barrios

In April 2005, Umicore Copper de-merged from Umicore Group and created a new independent Copper company called Cumerio. As a separate company, Cumerio is a major European copper smelter and refinery and a leading producer of copper products such as wire rod, billets, cakes and specialty rod with a total production capacity of copper products in excess of 500,000 tpy with production plants in Belgium, Italy and Bulgaria. The Pirdop Smelter is the only state-of the-art smelter in South East Europe and it makes Pirdop the natural hub for the copper industry in the region. In order to be competitive in the international market the main challenges facing Cumerio are to maintain its low cost structure and to achieve higher production volumes while reducing its impact to the environment and striving for continuous improvement of the production process. Cumerio's state-of-the-art smelting facility in Pirdop has recently increased the anode production capacity to 250,000 tpy by the installation of the third evaporative cooler on the converters section that allows operating with three-hot converters. In April 2007 a general shut-down for repair and modification on the Flash Smelting Furnace and Waste Heat Boiler is envisaged. At this time a revamp of one of the existing Sulphuric Acid Plants is planned, resulting in a further copper capacity increase to 275,000 tpy with modest Capex. In 2005 Cumerio received from the Bulgarian Ministry of Environment and Water the Complex Permit under the EU IPPC criteria. Accordingly an Environmental Compliance Program was defined targeting a large reduction in the secondary emissions. The system will be commissioned in May 2007. In order to better integrate the smelter and refinery in Pirdop and to respond to the growing demand for cathodes in the region, a new state-of-the-art Electrolytic Refinery with an installed capacity of 180,000 tpy will replace the existing refinery. The new refinery is expected to be fully operational as from early 2008. This paper describes the challenges and the projects.

Jan 1, 2007

By W. R. Cowan

The availability of mineral aggregates for construction purposes is rapidly declining through inadequate resource planning. restrictive zoning and legislation , and competing land uses. The Geological Branch of the Ontario Ministry of Natural Resources has undertaken to provide aggregate inventory reports for all townships designated under The Pits and Quarries Control Act, 1971, and eventually for all towns hips in heavily populated areas. The reports contain maps and recommendations for extractive zoning by municipalities; of necessity only the largest deposits are given priority recommendations. It is intended that these reports should improve the resource planning in areas underlain by large aggregate deposits. The inventory is only possible because a concentrated effort has been made to map the Quaternary geology of populated areas over the last ten years. Future needs require that we develop methods to determine the extent of poorly defined and buried aggregates and that we look for natural alternatives.

Jan 1, 1978

By J. L. Thornton

Introduction The importance of coal in our economy is well established, but it may not .be so generally realized how important a part it plays in our daily life. Select a product - any product - and, if it is made in America, bituminous coal has touched it first. Everywhere we will find coal, derivatives of coal, or functions made possible by coal. Apart from the well known major uses of coal for domestic purposes, coking, utilities, railways, and manufacture of steel and cement, there are over 200,000 products derived from coal, from lipstick colours to nylon products and perfumes. An item of interest is the recent action of the Canadian Government in voting $90,000 for development of coal deposits in Yukon Territory to make coal available to the settlers in that area. The value of this move, in case of some emergency, is very evident. Coal in its several stages of formation as peat, lignite, sub-bituminous, bituminous, semi-bituminous, semi-anthracite, and anthracite, has been used for centuries. Coal, as such, was not very well known to the ancients. First reference to "magic stone', or coal, was in 371 BC by Theophrastus, a pupil of Aristotle. This substance was said to burn like wood coal or charcoal and was used by the smiths. The first record we have in modern times was in 852 AD, when sea coal was gathered by the cowled monks of Durham, in Britain, and even at that time a major problem was transportation. Our first record of coal in this continent was near Richmond, Virginia, in 1700. Commercial mining was not under way, however, until 1750. The anthracite fields (presumably in Pennsylvania) were opened in 1793. Even so, there was no extensive mining until about the year 1820. The famous Pocahontas coalfields were opened in 1883. The earliest record of coal mining in Canada is about 1746.

Jan 1, 1950

By Marie-Eve Boucher

The slag in iron ore pellets allows wet sintering during firing and leads to suitable bounding. The process of slag formation differs whether it takes place in the core or in the external zone of a pellet. In the core, hematite can be reduced to secondary hematite, depending on the temperature and on the carbon monoxide/dioxide partial pressure ratio. The reaction rim that appears at the outskirts of a silica particle in contact with the FeO bearing magnetite is considered as the slag precursor in the core of the pellet. By contrast, in the external zone of a pellet, where O2 is available and CO partial pressure is very low, the first step towards slag formation is flux decomposition, mainly dolomite and limestone. The CaO liberated through this reaction will be available to react with hematite by solid diffusion to form calcioferrites, which play an active part in the slag evolution process. These two slag formation paths will be explained.

May 1, 2007

By The Staff

BEFORE going into detail on the subject to be presented, a brief outline of the Company's earl y history would not be out of place. Prospecting and mining on a small scale was started in 1876 on the site of the present open pit at Thetford Mines. The property was purchased from the Crown in 1878 and Johnson's Company was incorporated in 1885. It is owned and operated today by descendants of the original shareholders. Many employees, through their fathers and grandfathers, have service records dating back three generations. The principal asbestos deposit at Thetford Mines is pear-shaped, with surface dimensions of about 2,200 feet in length by 1,300 feet in maximum . width. Its long axis strikes northeast and the dip is nearly vertical, but irregular in detail. It is known to extend to a depth 1,200 feet below the original surface, but its area at that depth has not been determined. Ownership of this deposit is divided among three active Companies: the Asbestos Corporation, Limited; Bell Asbestos Mines, Limited; and John-son's Company. Johnson's Company owns a section about 1,000 feet in length and 500 feet in width, bounded on the northeast by the King mine of the Asbestos Corporation and on the northwest by the Bell pit. On Johnson ground, there was originally a large outcrop o~ asbestos rock which dipped toward the south below overburden. This was mined until recently by open pit, the overburden being stripped off as far southward from the original outcrop as was economically possible. As the. pit was deepened, within side walls maintained at a maximum safe slope, its floor area, of course, became progressively smaller, and eventually the pit would have wedged out against the Bell property line. It became necessary, there-fore, to introduce some other method of mining before production became seriously curtailed by a shrinkage of the pit area.

Jan 1, 1941

By Peter Hayes, Evgueni Jak, Taufiq Hidayat, David Grimsey, Denis Shishin

"An integrated nickel flash smelter is operated with Peirce-Smith converters at the Kalgoorlie Nickel Smelter. To improve the partitioning of arsenic between slag waste and matte product, an option to modify the slag–matte chemistry by addition of CaO was analysed. A combination of plant sample analysis, high-temperature laboratory experiments and thermodynamic modeling was carried out to evaluate the process options. The high-temperature experiments involved the re-equilibration of industrial matte-slag samples at 1225 °C and P(SO2) = 0.12 atm, rapid quenching in water, and direct measurement of phase compositions using electron probe X-ray microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrometry (LAICPMS). A private thermodynamic database for nickel sulfide smelting and converting was used together with the FactSage thermochemical software package to assist in the analysis of the distribution of elements between slag and matte as a function of CaO addition. The thermodynamic predictions combined with experimental data obtained in this study can be used to characterise the effect of CaO fluxing on the slag–matte thermochemistry during the nickel sulfide converting.INTRODUCTION At the Kalgoorlie Nickel Smelter (KNS), nickel sulfide concentrate is processed in an Outotec-type flash furnace to produce nickel matte containing +47 wt% Ni. Separation of nickel matte and waste slag from the flash smelting is enhanced through settling in the electric arc -heated zone attached to the flash furnace. The flash furnace matte is further processed in a Peirce-Smith converter to produce Ni-rich matte containing +66 wt% Ni (Crundwell, Moats, Ramachandran, Robinson, & Davenport, 2011). Iron silicate-based slag is used in the converting process at KNS. Most of the arsenic is contained in the final matte and very little of the arsenic partitions into the slag. Previous work by Font et al (Font, Hino, & Itagaki, 2003) shows that the distribution ratio of arsenic between calcium ferrite slag and nickel-matte (LAsslag/matte) is significantly higher than that between iron silicate slag and nickel-matte, where LAsslag/matte = (wt pct As in slag)/{wt pct As in matte} (1)"

Jan 1, 2017

By Richard J. H. Barclay

The Lac Otelnuk iron property is located in the Province of Québec in the Northern Labrador Trough. The Labrador Trough is an extensive geosyncline of Proterozoic rocks, unconformably underlain by Archean gneisses. The Lac Otelnuk iron property hosts two significant magnetite iron-formation taconite deposits that outcrop, are sub-horizontal and are known to extend for at least 25 kilometres along strike. The host sedimentary rock package that includes a cherty iron formation is weakly metamorphosed to greenschist facies.

May 1, 2007

By Andrew Abraham

Continual improvement is the key to success in today?s competitive global arena. You require tools that promote dynamic quality management, deliver cost savings to your bottom line and provide the foundation for process improvement. ISO 9000 and ISO 14001 management systems and OHSAS 18001 are those tools. Since their inception, the benefits of ISO management systems and registration have been touted as the way to achieve better bottom line results. This spurred many companies to embark upon the road to registration with high expectations. The potential benefits of ISO management system implementation and third party registration that are commonly provided by Registrars and consultants are compelling adverts for success. ISO 9001:2000 is promoted as an essential tool for systematic efficient and affective management controls that provide a framework for analyzing errors and improving a company?s internal operational processes. It also allows companies to comply with internal and external customer and regulatory requirements thus continually improving the quality of their products and services and thus enhancing customer satisfaction. This, in turn, leads to greater customer recognition and increased market share. ISO 14001 implementation and registration may assist your company in reducing its litigation risk, raw material and energy consumption, waste disposal costs and possibly non tariff trade barriers. It should also provide continuity of operations, enhanced operational efficiency and consequently a competitive advantage in the market place. Registration of your ISO 14001 management system should also improve your company?s profile and credibility leading to regulatory flexibility and improved community goodwill. All of this will be a catalyst for improved morale and pride by employees and management alike. Likewise, OHSAS 18001, the latest certification specification for Occupational Health and Safety Management Systems supports Occupational Health and Safety legal and regulatory obligations and compliance, manages & controls Occupational Health and Safety risks and improves performance, safety culture and efficiency. OHSAS 18001 is an audit certification, and not a legislative requirement. Suggested benefits of implementation include reduction in accidents, lost time and associated liability and insurance costs and improving reputation and credibility through demonstrated commitment to health and safety. The foregoing increases access to new customers, joint venture partners and financing The skeptics say these are motherhood statements and lack corroborative evidence, i.e., ?Show me the money!?

May 1, 2003

By Mario Bergeron

L'exploration géologique pour les EOP (EOP: platine, palladium, iridium, osmium, ruthénium, rhodium) requiert avant tout des méthodes appropriees à la mesure de ces élémenIs. L'approche analytique choisie doit tenir compte de plusieurs facteurs, les plus importants étant: le type de materiel analysé, sa representativite, la sensibitite de la methode et les cotits reliés à son utilisation. Dans cette optique, plusieurs démarches ana/ytiquessont possibles, toutes requérant une étape de préconcentration. L 'une des plus adéquate consiste à effectuer une préconcentration par fusion plombeuse suivie d'une analyse par émission au plasma, cette procédure permettant de mesurer Ie platine, la palladium et Ie rhodium à des couts compétitifs (15 $/échantillon). Advenant 10 presence de teneurs appréciables de l'un ou plusieurs de ces éléments, une préconcentration par fusion au sulfure de nickel suivie d 'une analyse par activation neutronique assure alors la mesure de tous les EGP ainsi que celie de l’or (90 $/échantillon). Il est important de noter que Ie nickel, ades teneurs superieures à 4%, interfère au cours de l'étape de préconcentration par fusion plombeuse, ce qui se traduit pas sous-dosage des concentrations en platine, effectivement presentes dans l'échantillon. Ainsi, les géologues à la recherche d'EPG dans des environnements géologiques riches en nickel devraient s'assurer que l'analyse utilise, au cours de l'étape de préconcentration, une fusion au sulfure de nickel.

Jan 1, 1990

By E. D. Fox

Introduction The financial statement of the hypothetical Gold Mining Company, which forms the background of this survey, was designed for the Institute with the express abject of having it assessed in respect to Profits by the several taxing bodies representing the Federal and Provincial Governments, which comprise the Dominion of Canada. On the completion of the figures, copies were sent to the several Ministers of Mines, accompanied by a request that they be submitted to their taxing authorities and assessed accordingly. The response, while it was not general, was very favourable, and at all times we were treated with the utmost courtesy and patience, and what has been set forth in the compilation bears the authentication of the various government officials who are immediately concerned with taxation. The data itself constitutes a fairly comprehensive digest of taxation as it directly applies to gold mining profits in Canada. The Hypothetical Balance-Sheet (See Exhibit A) In the balance-sheet schedules 1 and 2 (Exhibit A), income is divided between taxable and non-taxable classifications, and here it should be noted that the division contemplates only the assessment for Dominion income tax. The same applies to the factors of exchange and depletion. Therefore, in making comparisons, it is to be borne in mind that the set-up for assessment to the Provinces, that is, Manitoba and Alberta, will stand as if the gross non-operating income is taxable, with the reservations as shown in the notes below the schedules.

Jan 1, 1934

By L. F. Haven

"The desirable shovel speed-torque curves are described, along with the characteristics of the more important electrical components used to approximate these curves. A particular shovel regulator system combining these components is discussed in detail and some of the advantages and disadvantages of the system are given.INTRODUCTIONIN 1959, STATIC CONTROL was for the first time successfully applied, installed and operated on a mining machine in North America. Since that time, a great deal has been learned about this control by the people maintaining these machines as well as by the de-signers.In 1961, the first SCR (Silicon Controlled Rectifier) or thyristor control system was installed on an excavator. This control differed from the earlier static control in that thyristor excitors supplied the generator fields directly. The development of thyristors of a sufficient rating to supply amounts of phase-controlled power to the generator fields eliminated the bulky Mag. Amp. -Rectifier combination previously used."

Jan 1, 1969

By Clifford S. Gibson

A year ago a paper (1) was presented at the Annual Western Meeting of the Institute regarding silicosis in Ontario mines. It described the whole problem as we see it and discussed the means of prevention. The work and aims of the Technical Silicosis Research Committee of the Ontario Mining Association, and of the Committee's field engineer, were fully described also and it is suggested that reference be made to this paper in order to have a better understanding of the observations which are presented now. These observations enlarge upon parts of the dust control measures already discussed and tell of general progress in the past year. They concern fifty properties, the majority of the operating mines, which vary in size from the hopeful prospect to established producers yielding 11,000 tons of ore daily. Most of these are gold mines; a few copper-nickel. The ores range from heavy sulphides to siliceous materials and they are mined by many methods from varying types of deposits. The majority of the latter are steeply dipping and all are found in Precambrian host-rocks. Up to the present, die greatest depth to which mining has penetrated is 6,400 feet.

Jan 1, 1939

By G. Shore

Radiation grafted structures my be fabricated to contain ion exchange groups selective to an ion complex. Proper choice of substrate and monomer will provide selective ion exchange with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures have been fabricated to ''capture'' gold, silver and palladium from dilute solutions. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their regenerating solutions are pure metal foil.

Jan 1, 1985

By P. Cain, B. Martens

"Grande Cache Coal (GCC), an investor-owned Alberta company, is in the final stages of the regulatory process leading to the resumption of coal mining in the Smoky River Coal Field of Alberta. Although many opportunities for low-cost, high-yield mining remained on the property, GCC opted for a long-term production plan that ensures stability for the local economy, sustainable use of the resources in the area, environmental responsibility and a satisfactory return for its investors.GCC entered the Alberta coal approval process in late 2000 with a public disclosure document. In October 2001, GCC formally submitted an application for mining approval and an environmental impact assessment (EIA) to the government and the public. The application covered the proposed Grande Cache Coal project, which includes the No. 7 underground mine, No. 8 surface mine and coal processing operations. The EIA provided a comprehensive investigation of environmental sensitivities in the project area, matched with environmental protection programs. The project is based on commencement of operations in late 2002. GCC’s plans are founded on a commitment to sustainable development and has framed this commitment in the context of a long-range mine development plan that will sustain the community of Grande Cache over the next 25 years. The Grande Cache coalfields offer extensive coal reserves and opportunities, for both surface and underground mining. Combining highly productive U.S.-style room and- pillar underground mining methods and conventional truck-and-shovel open pit mining, GCC’s approach to sustainable development encompasses community involvement and reclamation of mine sites to productive land uses after mining."

Jan 1, 2002

By D. R. Boyle

"The basal type uranium deposits in south central British Columbia occur within unconsolidated, late Miocene fluvial paleochannel sediments that overlie major fault zones within the Okanagan Highlands Intrusive Complex. Prior to the formation of mineralization, paleovalleys containing host sediments were flooded by Pliocene valley basalts of the Plateau Basalt Formation. Five uranium deposits have been outlined to date, of which the Blizzard (4020 tonnes U) and TYee (650 tonnes U) are the largest. The basement intrusive complex underlying the deposits varies in age from early Cretaceous to Eocene and is comprised of quartz monzonite, granodiorite, Coryell monzonite, porphyritic granite and pegmatite.The mineralized host sediments comprise a complex sequence of interfingering conglomerates, arkosic sandstones and mudstones. Organic material is abundant in many, but not all, mineralized beds. Uranium mineralization is present in the form of uranous (ningyoite) or uranyl (saleeite, autunite) phosphates coating clastic grains and filling voids. Because of very strong reducing conditions related to large concentrations of marcasite and organic material, ningyoite is the only uranium mineral in the Tyee deposit, whereas the Blizzard deposit contains a more complex assemblage of minerals (saleeite, autunite, ningyoite). The observed paragenetic sequence of mineral precipitation in the Blizzard deposit (autunite-saleeite-ningyoite) indicates that the uranyl minerals, saleeite and autunite, are primary. Small amounts of Zn, Ni, Co and Mo have been introduced into the Blizzard deposit whereas Mo is the only non ore-forming element enriched in the Tyee deposit. Mn is the only depleted element in both deposits."

Jan 1, 1986

By D. E. Keeley

Introduction Gunite is a mixture of sand and cement applied to any surface by being shot by compressed air through a nozzle, where it is wetted just before leaving the orifice. The mixture is transported through a hose from a machine called a 'cement-gun'(l). Guniting of rock surfaces has been standard practice at the Mcintyre Porcupine Mines, Limited, for several years. Where used on walls and backs of cross-cuts; shaft stations, and other rock openings, as an air seal, gunite has eliminated the necessity of constant scaling to keep rock from falling from these places, and, under worse conditions, it has been used in place of timber supports. This has been of definite help in reducing costs, promoting safety, and minimizing fire hazards. During the past year guniting has been quite extensively used here in the rock head-works of the new internal shaft, No. 12, sunk from the 3,875-foot level. Gunite is at present being applied to the stations of that shaft well below a mile from the surface. This paper describes the method of guniting as carried out at the McIntyre, and illustrates how, by the adoption of this process, mining problems connected with scaling and loose ground have been completely solved. It is hoped that the information presented may stimulate discussion and assist in the use of gunite in this and other mines. The guniting method of applying cement was first developed by Carl E. Akeley (2), Curator of the Field Museum, Chicago, in 1907, and was exhibited in New York at the Cement Show in 1910. The museum was located in one of the old World's Fair buildings, built of roughcast and in bad repair. Mr. Akeley, who was a man of inventive nature, set about devising means of applying cement to repair the walls. The cement-gun was the result. Mr. Akeley was a taxidermist of note, a sculptor, and also the inventor of the Akeley camera. In his work, he was in the habit of using fast setting materials to build up foundations for statues, etc.

Jan 1, 1934

By W. K. Gummer

"THE LOCATION of Canada's present aluminum industry is determined by availability of hydroelectric power, and ready access to ocean transport facilities. The chief raw material for the production of the metal is imported by ship over several thousand miles of water. In times of freedom of shipping and uncontested movement this provides the industry with its cheapest method of operation. However, during the early part of the last decade the general conditions of ocean and rail transportation were such that interest in the treatment of materials other than bauxite was greatly stimulated. This was the case not only in Canada, of course, but in most other countries.Canada has no deposits of bauxite and much research was carried out on other aluminous materials, chiefly silicates, in an effort to develop more or less economic and feasible methods of treatment. In the United States, this research was considerably more extensive. Some projects were early shown to be of little or no value, whereas others, including the widely publicized lime-sinter and soda-lime-sinter methods, became important. In North America, however, apart from the application of the sinter method to the hitherto waste-product (red mud) of the normal Bayer plant operation, none of these processes contributed appreciably to the production of aluminum during the war. In certain European countries, on the other hand, largely because of their situation with regard to bauxite deposits, they had a more general application, and Germany, for example, produced alumina from clay, ashes, and slag by at least four methods."

Jan 1, 1952

By A. Vien, A. J. Neale, B. C. Flintoff, R. P. Edwards

Froth flotation is one of the most widely used and effective processes for mineral beneficiation. First introduced in 1911, flotation technology has seen many developments over the past 80+ years. Innovations in reagent chemistry, equipment design, process analysis and process control have given design and plant engineers a powerful set of "tools" for process optimization. However, it does not follow that all flotation systems are optimized. As Klimpel observes: "The problem with the industrial flotation process is that it is relatively easy to get reasonable results, and relatively difficult to get excellent results" Klimpel (I 988). While reasonable was sufficient in the past, competitive forces will make excellent necessary in the future. Judging by the activities in many Canadian plants this transition is already underway. This paper examines the role of some of the optimization "tools" in effecting this change.

Jan 1, 1994

By R Zavadil, S Kuyucak, F Fazeli

Proton exchange membrane (PEM) fuel cells generate electricity by reacting hydrogen and oxygen. A thin, bipolar electrode material provides a medium for electron exchange with the electrolyte, alternately serving as anode at the hydrogen-rich side and cathode at the oxygen-rich side. Stainless steels have sufficient corrosion resistance to qualify as bipolar plate materials. However, the protective chromite layer increases the contact resistance, the battery’s internal resistance; and thus, decreases the electrical efficiency of the fuel cell. A heat-treatment is proposed and investigated via simulation by ThermoCalc / Dictra and experimentally, to generate a sufficient quantity of conducting surface carbides that breach the protective layer. Once carbide growth is arrested, a subsequent heat-treatment is also needed at a higher temperature to restore the corrosion resistance by filling-in the Cr-depleted layer (sensitization) around the carbide particles.

Jan 1, 2014

By Brandt Porter, Lawrence K. Nordell, Alexander Potapor

"Improving comminution efficiencies with better machine geometries and motions, improved nip angles, rock movement control, and voids regulation among rocks are some of the next steps to better machine performance. Recent gains (~30%) using high pressure grinding rolls (HPGRS) and vertical roller mills, in theory and practice, are based on Prof. Klaus Schönert’s academic studies (1979–1996) on rock breakage physics. More recently, University of British Columbia Prof. Bern Klein’s studies (2006–present) via the Ph.D. thesis of Z. Davaanyam (2015) further validate theory with practice from laboratory measurements used in this paper.They demonstrated ideal rock compression breakage, within HPGR and vertical roller mill machines using a piston-die apparatus. Similar rock size range is used. The piston-die confine rock breakage behavior. However, these studies do not extend to larger rocks (> 75 mm), and do not demonstrate the influence of rock voids among bifurcation of rocks during comminution. Further, machines fed with larger rock sizes, such as gyratory, jaw, and cone crushers, are not designed or evaluated for geometry nip angle efficiency.Herein we illustrate a performance gain of a new comminution machine, the conjugate anvil-hammer mill (CAHM), first presented at SAG 2011 (Nordell, 2012). The CAHM machine digests rock sizes 400% larger than HPGR, improves rock grip/nip geometry, better improves rock voids, improves surface wear life > 500%, and improves rock containment and slippage during compression. In all, the CAHM machine shows 22 potential improvements over the HPGR. Most importantly, CAHM shows a 50% kWh/ton improvement compared to the HPGR. Our studies use an advanced Discrete Element Method (DEM) computer program called ROCKY. ROCKY simulates moving boundaries, surface wear mechanics, and incorporates rock breakage physics based on the fundamentals of JKMRC T10 protocol [×] with tuned A × b breakage parameters.We calibrate rock breakage in our DEM code to mimicking both UBC laboratory piston-die and HPGR comminution measurements. We then model CAHM with these known ore and machine properties. Differences are illustrated using DEM techniques on each machine, including key points of when each: use geometry; initiate bifurcation breakage; provide a map of particle size distribution by location; illustrate the importance of controlling voids to minimize agglomeration after breakage; machine performance limits; and kWh/ton benefit."

Jan 1, 2016