Search Documents

By G. Auld

"A simple method is presented whereby the additional quantity and static pressure necessary to compensate for ventilation duct leakage may be estimated using the circular reference functions of modern spreadsheets. Favourable comparisons have been made to the National Coal Board (United Kingdom) design charts and to a case study analysis. IntroductionIn mining, most ducted systems are applied to the development of access tunnels, and most of these systems leak to some extent. When the ventilation duct fails to deliver the required quantity of air to the work place, there is a significant contribution to the development costs, either directly or indirectly.Directly — More air and more pressure are required to compensate for the leakage, more capital development (ventilation shafts, parallel drives) are required because ventilation systems cannot push the fresh air far enough, and longer re-entry times to ensure toxic blast fumes to be diluted.Indirectly — There is a reduction in productivity because of the inclement atmospheric conditions, and/or closure of development ends because of unacceptable atmospheric conditions at the working place. This has been exacerbated over the last few decades because of the increased use of diesel equipment of ever increasing power, and the more stringent Occupational Health and Safety requirements demanding more air flow per kilowatt of diesel power.The leakage from a duct must, therefore, be reliably estimated in order to assess the effectiveness and construction of the system; assess the effectiveness of the maintenance or repair of the duct; appreciate the cost of the leakage, and therefore apply effective maintenance and installation procedures; and engineer safer, healthier and more cost-effective ventilation systems."

Jan 1, 2002

By Paul R. Terry

This paper presents a brief picture of the quality of coal produced in Eastern Canada for use in thermal generating stations. It describes, in particular, the characteristics of coals burned in six power plants -two in New Brunswick and four in Nova Scotia. Each station is dis-cussed in turn, and comments are made on the coals used therein with regards to origin and physical and chemical properties affecting station operation. A table of coal data shows, at a glance, the wide variation in the quality of coals received by these stations from producers in New Brunswick and Nova Scotia. "The promotion of improved coal quality for thermal generation can benefit our national economy." T HIS is the opening statement in a paper which was presented by Mr. D. A. Pirttinen at the Coal Division's Toronto meeting in April, 1960. In bringing the power engineer's viewpoint to the coal producers' attention, Mr. Pirttinen made a survey of utility steam plants operating in Canada, and the results of this survey formed the basis for his paper, which he titled: "Generating Station Coal Quality.

Jan 1, 1965

By Ludwig M. Strah

"Wear is a universal problem and is present in all cases wherein one weighted surface moves with or relative to another surface. A practical description of wear as applied to mineral processing plants is outlined.With the advent of higher material and maintenance costs, more attention is being focused on the field of wear resistant linings. The aforementioned is magnified today as the production facilities continue to be designed to handle larger daily capacities. These changes, higher costs and larger plant handling facilities have necessitated the introduction of different materials and designs to combat the never ending battle against wear.In order that wear be understood, it can be relegated to two specific types:1 - Mechanical Wear - due to movement of one loaded surface relative to another.2 - Chemical Wear - more easily defined as corrosionMechanical wearMechanical wear can be subdivided into two basic forms:A.,Material movementB.,Material impactMaterial movement Abrasion is the result of, as earlier stated, the straight move¬ment of one loaded material relative to another.Material impact Is the striking effect when a mass strikes another from various angles and at various speeds. Impact can be severe enough to permanently damage and distort the basic component installed to overcome impact."

Jan 1, 1983

By Tao Long

Recently, the great amount of funds has been invested in the reconstruction of damaged infrastructure and house of subsidence area of coal mine and mine reclamation. This is a benevolent and popular work, which is highly praised. However, because of complicated collapse area problems in China, especially the less integrated control research in the collapse area of metal mine, and the technological weakness, how to effectively control the subsidence area, restore landscape and ecological environment, and utilize the abandoned mine land, are major issue related to the mining area of sustainable development. The research situation about the formation of metal mine collapse area at home and abroad is reviewed, and then the effect of the collapse area on the mine safety and ecological environment, the existing technical problems and development direction are analyzed. Lastly, the technical measures of the collapse area control and cooperative underground mining is put forward.

Oct 1, 2010

By M. Pearson, J. Irvine, L. Mercer, P. Lauzon

Severe service ball valve performance has a direct impact on the mechanical availability of high pressure oxidation and leach plants. The primary function of these valves is to isolate the autoclave for maintenance. Valve failure has historically contributed significantly to the maintenance downtime of these process plants. An understanding of the root causes of valve failures is the first step in increasing the reliability of the severe service ball valves. A rigorous failure analysis practice has been developed by Hatch for investigating refractory failures in furnaces and kilns based on Kepner-Tregoe methodology. The method has also been modified for valve failure analysis. From a root-cause failure tree analysis of each of the valve components, a list of all potential valve failure mechanisms was developed for ranking and evaluation, along with recommendations for further valve development. The purpose of this paper is to present the reader with the modified Kepner-Tregoe method and examples of this analysis.

Jan 1, 2004

By Ben R. Bjorkman

The future is here ? or at least that?s what Mine Planners predicted some 15 years ago ? that by 2004 we would have man-less mines running themselves using space-aged technology. Truthfully, though, there hasn?t been much change in mining methods in the past decade, but thankfully that?s all about to change. The benefits of autonomous ? even Tele-operated mining (especially in narrow-vein ore bodies) are wellknown: increased production hours by eliminating travel time to and from the face, continuous production at the face while crews screen and bolt behind the working equipment, less liability for workers? safety in certain areas, etc. But when plans are put in place to accomplish this vision, things stagnate and production carries on as before. This paper examines the components necessary to make that vision a reality. First we?ll detail the technology required to enable Tele-operation ? even autonomous operation of mining machinery, then we?ll look at what?s wrong with the current way we?re mining, and finally conclude with a critique of the machinery itself.

Oct 1, 2004

By J. M. Hemstock, H. L. Ames

THESE forums have been held annually since they were introduced by Mr. L. E. Djingheuzian in 1957. The response of millmen to questionnaires such as the one this year is ample evidence of the interest these create. This year's topic is unlike those of past years since it is an attempt to understand a new concept of grinding rather than to improve the old. Before, we were thinking in terms of 2-5 cents improvement in grinding costs, now we will be discussing savings of 15-2 5 cents. As a background for this forum we will begin by summarizing the major controversial issues relating to grinding with steel, many of which will undoubtedly apply to pebble milling. Our •task to-day is to learn what has already been done in pebble milling and obtain a fair overall view of this method of grinding.

Jan 1, 1961

By J. Ran

"Hangingwall sloughing is the major cause of unplanned stope dilution in open stope mining. Understanding the hangingwall sloughing mechanism can guide the stope design in minimizing the unplanned dilution and improving muck size and therefore mining efficiency. Though the modified stability graph method may be adopted to assess the hangingwall stability, for mines where the hangingwall is inaccessible, the required parameters are difficult to define and some of the simple influential factors cannot be easily identified in this method to provide guidelines for stope design.This paper identifies the main modes of hangingwall sloughing in open stope mining based on detailed data collected from mined-out stopes and site observations, applies the voussoir beam notation to analysis of the hangingwall sloughing mechanism, compares the model analysis results with the collected stope data, and provides guidelines for stope design and model application. Finally, examples are given to demonstrate the time and support effects on hangingwall sloughing and stope dilution."

Jan 1, 2002

By Reno Pressacco

Abstract- Agrium Inc. is a world leader in the production, distribution, and marketing of agricultural products and services in both North America and Argentina. The new phosphate mine and mill complex located southwest of Kapuskasing, Ontario, was constructed to replace an offshore supply of phosphate rock, and produces a high-grade phosphate concentrate. The Cargill Township Carbonatite Complex is one of a series of carbonatite complexes in the region that are hosted by the 1.9 Ga aged Kapuskasing Structural Zone. The carbonatites in the mine area have intruded Archean gneissic granodiorite rocks of the Wawa Subprovince, and metasedimentary rocks of the Quetico Subprovince. The Cargill Carbonatite Complex displays a typical concentric zonation pattern from an outer ring of alkalic pyroxenites, through an inner ring of sövite-carbonatite, to a central core of rauhaugite-carbonatite. The initial carbonatite intrusion and subsequent residual orebody have been modified by faulting such that the northwestern third of the complex has been displaced approximately 2.5 km northeast. The phosphate ores are composed principally of residual apatite sands that were formed by the weathering and dissolution of the soluble minerals of the carbonatite protolith. These ores are subdivided by their iron content into high grade (A ores) and lower grade (B1 and B2) ores. They are separated from the primary unweathered carbonatite by a layer of saprolite, whose thickness varies depending upon the composition of the underlying carbonatite. Cretaceous waste materials consisting of well-sorted silica/kaolinite sand and peat deposits are typically found to stratigraphically overlie the ores. A minor amount of the ore feed comes from cemented phosphate ores. All rock types are covered by Pleistocene glacial tills and clays.

Jan 1, 2001

By D. S. Flett

"The current state-of-the-art of chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is reviewed. General considerations regarding the various flowsheet steps are examined and options discussed. Then, individual flowsheets are presented and discussed. Finally, the forward prospects for chloride hydrometallurgy for treatment of complex sulphide bulk concentrates is considered and conclusions drawn concerning the likely application of this technology in the future. IntroductionHydrometallurgical processes for treating sulphide concentrates, in general, have received considerable attention over the last three decades or more. Many flowsheets have been developed, many pilot-plant studies have been undertaken and several processes are now successfully operating. For example, direct ammoniacal pressure leaching has been used by Sherritt Gordon Mines since the 1950s to extract nickel from pentlandite concentrates, the roast-leach-electrowin route is widely used to recover zinc from sphalerite concentrates and direct sulphuric acid pressure leaching of sphalerite concentrates has been successfully commercialized. Also, Duval Corporation operated a direct cupric/ferric chloride leaching process (Schweitzer and Livingston, 1982) with electrowinning to recover copper from chalcopyrite concentrates, this process (now closed) being the only chloride process which has been commercialized for a sulphide flotation concentrate. Despite these developments, it has long been considered, particularly for copper sulphide concentrates, that direct hydrometallurgical processes are in the main unlikely to be able to compete successfully with smelting for large-scale operations of simple high-grade single metal concentrates. As long as such concentrates can be produced commercially, smelting is likely to remain the principal processing route (Flett, 1981). This view is being challenged nowadays through pressure leaching developments made by Dynatec and CESL in Canada and the recent start-up of the Western Metals Gunpowder plant at Mt. Gordon in Queensland (Flett, 2000). Complex sulphide ores offer even greater opportunities because of the ability to produce a bulk sulphide concentrate from the complex sulphide ore with considerably higher metal recovery than is often possible from the production of individual metal sulphide concentrates from differential flotation. Interest continues to focus on hydrometallurgical solutions to these processing problems, particularly with regard to chloride hydrometallurgy. This paper, therefore, reviews current state-of-theart with respect to chloride hydrometallurgy"

Jan 1, 2002

By T. Liu, C. Shi, T. Fu, M. Zhong

Water inrush in coal mines is induced by the imbalance of the groundwater flow field and the engineering geo-mechanics field. Therefore, to prevent water inrush it is important to predict the critical hydraulic pressure of water inrush in coal seam floors. This paper will investigate a method for conducting theoretical forecasting of the critical hydraulic pressure of water inrush in coal seam floors by adopting the combination method of a genetic algorithm-neural network. First, the topology structure of a neural network (NN) based on genetic algorithms (GA) will be determined and then the critical pressure of water inrush in a coal seam floor using the chosen NN will be predicted. Finally, theoretical forecasting results will be compared with actual measurement results to determine the feasibility and applicability of this method.

Jan 1, 2008

By A. P. Bois, K. Saleh, A. Ghorbal, V. Hajiabdolmajid, G. Ballivy

"The knowledge of the initial stress field is not always sufficient to ensure the stability of mining stopes due to the high-stress variations generated by mining. Monitoring of these openings is then necessary and can provide quantitative information (deformations and stress variations) as well as qualitative information (state of stability).An applied technique for following the variations of stress and deformation in static and dynamic conditions, in relation to the evaluation of the stability of underground openings known as “Cylindre Instrumenté de l’Université de Sherbrooke” (CIUS) is discussed in this paper. In addition, a data acquisition system combined with a rock failure warning system has been developed to be connected to the CIUS for detecting the instabilities, which can endanger the stability of underground openings. Also, the installation of six CIUS and a data acquisition system as well as the selected procedure of programming in a warning system are briefly described."

Jan 1, 2003

By Unknown

We are indebted to the Consolidated Mining and Smelting Company of Canada Limited for the several pictures in this issue showing the progress made in new construction at Tadanac and at Bonnington Falls, B.C. Plate No. 1 shows the down-stream side of the No. 1 hydro-electric station of the West Kootenay Power and Light Co. Limited at Bonnington Falls, on the Kootenay river, at which 17,500 k.v.a. will be developed to meet the requirements of the enlarged zinc and lead refineries at Tadanac. The generators, exciters and switch apparatus were supplied by the Canadian General Electric Company and the step-up transformers by the Canadian Westinghouse Company Limited. The plant throughout was designed, manufactured and erected by Canadians. Plate No. 2 shows the casting room of the new lead-plant and plate No. 3 the new tank-room of the electrolytic lead refinery at Tadanac. These additions will increase the capacity of the lead refinery by some 150 tons daily. The extensions also include practically doubling the zinc plant, and the gold and silver refineries. With the exception of the new stack, all designing construction and installation of the various plants is being done by the Company's own employees at Tadanac. Plate No. 4 shows the progress made in the construction of the new reinforced concrete stack at Tadanac. This stack, of 21 feet inside diameter at the top, will be brick lined and when completed will rise 400 feet above its foundations: the tallest of its kind in the world. The construction is in charge of the Rust Engineering Company of Pittsburgh, Pa. Plate No. 5 is a panorama of the Tadanac smelters and refineries. The photograph was taken from the roof of the lead smelter and gives an excellent idea of the size of the plant and its surroundings. Tadanac produces electrolytic lead, zinc and copper and fine gold and silver. During 1924 the company treated 1,333,523 tons of ore and produced: 161,400,- 769 pounds of lead; 92,197,824 pounds of zinc; l,382,750pounds of copper; 4,074,044 ounces of silver, and 26,976 ounces of gold.

Jan 1, 1925

By R. Rosenblum, J. Y. Kim, D. Shink, K. G. Stowe

"A small scale continuous flotation cell was designed and constructed at the Noranda Technology Centre to develop a mobile testing flotation circuit located next to the production circuit. This mobile small scale flotation pilot plant can easily and economically be set up at any circuit in a mill and used to evaluate and predict plant performance against a given flotation condition. The main feature of the cell, beside the provisions of automatic pulp level and feed rate control, is to provide a reduced surface to volume ratio approaching to that of an industrial machine.This paper describes the basic design and the results of various testwork carried out to date including aeration, conditioning, reagents, recirculation, flotation gas, etc. are presented in comparison with the plant production results. INTRODUCTIONStudy of the behaviour of an ore during concentration by flotation process starts, in general, with a series of tests in laboratory cells. Given the discontinuous nature of these tests, the information obtained by such a study is somewhat limited. It has long been recognized that laboratory test results are not always reproducible in pilot plant tests and subsequently, the pilot plant results do not always predict plant performance. The differences are often blamed on batch vs continuous operations, grinding media, size distribution, aging (oxidation), water quality, equipment, operator's skills, etc."

Jan 1, 1992

By N. C. Clarke, T. Wu, M. le Page, K. J. Henley

In 1994, Gold Mines of Australia acquired the rights to the historic Mt. Lyell copper mine, and commenced a feasibility study into expanding production. The ore was shown in laboratory tests to be amenable to single-stage, fully autogenous grinding (FAG) of underground primary crushed ore, and this route offered the maximum cost savings. Flotation performance was expected to be enhanced. However, batch flotation tests done on pilot-scale autogenously ground ore showed an unexplainable recovery loss of between 1% and 3% Cu. A second pilot plant trial was set up, with the ground product feeding banks of continuous flotation cells. Single-stage FAG, FAG/pebble and FAG/ball circuits were tested. Results confirmed a loss of about 3% recovery with single-stage FAG milling. The FAG/ball circuit eliminated the loss. Analyses showed that autogenous milling probably produced more chalcopyrite/pyrite composites and that recovery of these composites was lower than with ball milling. In size fractions below about 53 microns, where chalcopyrite is well liberated, copper recovery was less affected by milling method and flotation selectivity. It was concluded that for the Mt. Lyell situation, a FAG/ball circuit was preferable to single-stage FAG.

Jan 1, 2002

By John S. Stevenson

ZEBALLOS is a relatively new mining camp. It is on the west coast of Vancouver island, approximately 195 nautical miles northwestward from Victoria. Previous to 1934, a small amount of placer gold had been recovered from the Zeballos river and tributary creeks. However, it was not until the winter of 1934-35, when shipments of high-grade gold ore were made from the property of the White Star Gold Mines, Limited, that lode gold mining really began. Since then, several new mines and many promising prospects have been found. Milling in standard sized mills only commenced late in 1938, when the 75-ton mill of Privateer Mines, Limited, and the 50-ton mill of Spud Valley Gold Mines, limited, were first turned over. The most striking feature of the camp is the high-grade quality of the ore as usually mined. At one property, the ore along a drift 650 feet long has ranged from 5.8 ounces per ton to 17.5 ounces, over average vein-widths ranging from 8.3 inches to 14.5 inches in selected blocks along the drift. One . high-grade shipment of 196.6 pounds of ore from the same property contained 142.877 ounces of gold. The present paper deals only with that part of the area in which mining operations are most active, namely the main Zeballos River valley and its tributaries, Spud and Goldvalley creeks. During the summer of 1938, prospecting was carried on beyond this circumscribed area. The geology and early developments in the area have been described in the following reports: (1) CLOTHIER, G. A., Annual Report of the British Columbia Minister of Mines, 1929, p. 376; 1930, p. 441; 1932, p. 205; and 1933, pp. 252-254. (2) GuNNING, H. C., Geological Survey of Canada, Summary Report, 1932, Part A-II, pp. 29-50, Zebaltos River Area, Vancouver Island, B.C. (3) STEVENSON, John S., Annual Report of the British Columbia Min-ister of Mines, 1935, pp. F-38-40. ? ( 4) BANCROFT, M. F., Geological Survey of Canada, Memoir 204, 1937, Gold-Bearing Deposits on the West Coast of Vancouver Island Between Esperanza Inlet and Alberni Canal. (5) STEVENSON, John S., British Columbia Department of Mines, 1938, Lode-Gold Deposits of the Zeballos Area. (6) MAcDoNNELL, G. F., The Privateer Mine, Zeballos; The Miner, Van-couver, B.C., December, 1938.

Jan 1, 1939

By Roger J. Higgins

Papua New Guinea is a country on the cusp of development, struggling to find a balance between the demands of national and regional growth, landowner expectations and the maintenance of cultural identity. Ok Tedi Mining Limited is the single largest contributor to PNG?s economy, representing about 10 percent of the country?s GDP. OTML is demonstrating that business and country risk can be managed through effective, respectful partnerships with local communities. OTML?s relationships with the communities of PNG?s Western Province are multifaceted. Communities have borne the brunt of the mine?s environmental impact, yet have benefited enormously from the development that the mine has brought. Importantly, the PNG economy is now the ultimate beneficiary of more than four-fifths of the dividends from the mine, the majority of which are held in trust for long-term sustainable development projects. The paper describes how OTML works with the Western Province communities to create a secure operating environment that recognizes the people?s aspirations for development and self-determination.

May 1, 2002

"Many advances in glass technology and processing are being made and the possibilities for glass as a material in the future appear unlimited. Float glass, glass-ceramics, high-strength sheet and container glass, glass-reinforced plastics, glass for electronic equipment, aerospace glass, glass fibres, glass vehicles, glasses with selective-reflective coatings and glare-reducing glasses, to name a few, provide areas of significance at present and for the future. There appear to be great opportunities, in certain localities of Canada, to develop new sources of raw materials for an expanding Canadian glass industry.New developments in the structural clay products industry have centered around facing brick as a structural load-bearing material, prefabricated brick panels, large-sized units, isostatic pressing of sewer pipe and auto-matic settmg of brick. Fast-firing techniques, using prefired or calcined raw materials, and the development of high-strength products will result in the use of a wider range of raw materials in the whiteware and structural clay products industries.Porcelain enamel, a material used for many years in domestic appliances and for sanitary ware, now is used extensively in architecture, agriculture, water tanks, highway signs and reflectors, and in products where resistance to corrosion-plus-temperature is important. Exotic composites of ceramics and metals, and specialized ceramic coatings applied on metals by various techniques such as flame spray, plasma jet, or vapour and chemical deposition have proved useful in materials for aircraft power plants, rockets, missiles and nuclear applications."

Jan 1, 1967

By Mike Rylatt

"The BHP Diamonds Inc. and Blackwater Group (Dia Met Minerals Ltd., Charles Fipke and Stewart Blusson) joint venture began production at Canada=s first diamond mine during the last quarter of 1998.Construction of the processing plant began in mid 1997. During the 1998 winter season, the heavy process plant equipment was delivered to the Ekati site, 300 km NE of Yellowknife, by the ice road. Towards mid 1998 the construction activities were complete and commissioning began. The mine officially opened in October 1998.Initial production of 9000 tpd kimberlite will be from the Panda pipe grading 1.09 ct/t at an average value of US$13O/ct.Processing starts with a gyratory crusher reducing the ROM kimberlite to 90% passing 15Omm before further reduction to minus 75mm in a WaterFlush crusher. The crusher product discharges into a 4m diameter x 7m long primary scrubber. After screening, the minus 75 +1 mm kimberlite is conveyed to a 250 ft feed bin ahead of the 1.7 m diameter x 1.1 m wide high pressure grinding roll. The HPGR produces 50% minus lmm in a single pass, the compacted flake product is dis-agglomerated in a secondary scrubber. The scrubber product is screened into a minus 25 +lmm heavy medium separation plant feed and conveyed to a 375t HMS feed bin ahead of two 150 HMS modules. Milled 270D ferrosilicon at a slurry density of 2.6 g/cc and HMS feed are pumped to three 420mm diameter cyclones. Heavy mineral concentrates, approximately 1 % of the plant headfeed, are pneumatically transported to the Recovery plant for final diamond recovery using wet high intensity magnetic separators and high intensity (attrition) milling prior to three stages of x-ray recovery. At full production, Ekati will produce approximately 2 kg/day of diamonds.This paper details the later commissioning phase and the first three months Oof operational activities during the build up to full production at the Ekati processing plant."

Jan 1, 1999

By Paul D. Merica

This year of 1926 marks the 40th. anniversary of nickel mining in Canada. Although the first nickel mine of the Sudbury basin was discovered in 1883, it was not until 1886 that the Canadian Copper Company was organized and actually began to mine copper-nickel ore from the Lady McDonald, Stobie and Evans mines. The intervening years have witnessed some exceedingly interesting nickel history, particularly interesting and gratifying as well to Canadians. Forty years ago, at the inception of Canadian nickel mining, the world's consumption of that metal was about 1000 tons per annum and this was supplied largely from New Caledonia ores refined in France. This nickel was used principally for the production of nickel-silver, coinage alloys, and for nickel-plating. No processes were then known for refining the Sudbury ores nor for the separation of copper from nickel. Consequently, the pioneers in Canadian nickel mining faced the double problem of finding a method of treating their ores, and of finding a market for the nickel when and if they could extract it.

Jan 1, 1926