Search Documents

By Donald W. Gentry, John F. Abel

This paper presents some of the results of a rock mechanics instrumentation program designed for, and implemented at, longwall panel 4N at the York Canyon Mine near Raton, New Mexico. The objective of this particular instrumentation program was to determine the response of the rock mass to longwall mining of a thick coal seam utilizing shield-type supports. Measurements were made in the rock along the ground surface, above the coal seam, in the coal seam, and immediately below the coal seam. Longwall test panel 4N had a total developed length of 762 m (2500 ft) and a face width of 168 m (550 ft), Fig. 1. The seam mining height in the panel area was approximately 3 m (10 ft). The average depth of overburden above the panel is 107 m (350 ft) although it ranges from 73-134 m (240-440 ft). Roof support at the face was provided by 116 Hemscheidt 320 HSL shields. These shield-type supports weigh 11.4 metric tons each.

Jan 3, 1978

By P. de Vitry, Willis P. Mould

THE wire saw is a tool not less than 60 years old, probably nearer 100 years old. It was developed in Europe and is reputed to have originated in Belgium. Frombold is said to be the original patentee. [ ] Wire sawing equipment, as indicated in Fig. I, is very simple. It consists of a three-strand wire cable, usually 3/16 or 1/4 in. in diameter, or a single flat ribbon of medium hard, tough, alloy steel twisted into a helix of those diameters, made to form an endless belt of any length up to several thousand feet. The wire is guided into the cut by sheaves mounted in slides on steel columns situated close to either end of the cut. The feed motion usually is controlled either by gravity or by hand-operated feed screws. The steel columns or "standards" range from 15 to 30 ft. in length. At the top is a swiveled arm supporting a sheave similar to the traveling sheave below. Immediately under the swivel-mounted sheave is a guy plate or collar with shackles attaching four chain or wire-rope guys with suitable tightening devices, or with two guys and two jack legs for supporting the standard vertically or at any desired angle. The usual drive is by a 10-hp. motor through a gear reducer, on which are mounted two grooved sheaves, one of which is keyed and the other free running on the shaft. Tension is provided by a car running on a track in line with the driving sheave

Jan 1, 1946

By W. L. Phillips

Stress-strain curves were obtained for single crystals of 70 pct Ag-30 pct Zn tested in tension and shear. Samples tested in tension and shear had comparable resolved shear stresses and stress-strain curves. The {111} <110> slip system was observed. It zoas found that the9.e is a barrier to slip in both latent close -packed directions and that the magnitude of these barriers is proportional to prior strain during easy glide. It was observed that cross-slip in tension and shear was most frequent in crystals with an initial orientation near <100> "Oershoot" zoas observed in tension. The amount of this "overshoot" was independent of initial orientation. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of easy glide which is characterized by a linear stress-strain curve and a low coefficient, d/dy, of work hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In fcc metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close packed planes, is the existence of latent slip planes in the fcc crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.ls Several theories have been proposed to explain the linear hardening and parabolic stages of the stress -strain curve.6"10 The easy-glide region is the least understood of the three stages. The stress-strain characteristics of Cu-Zn, which shows a long easy-glide region, have been extensively investigated."-" In light of recent ideas on dislocations, cross-slip, effect of solute atoms, and stacking fault energy, it was felt that the certain features of this earlier work might be compared with another alloy, Ag-30 pct Zn, which also exhibits a long easy-glide region. Tension and shear stress at room temperatures were employed. The results obtained, together with some interpretation of the observations, are described below. EXPERIMENTAL PROCEDURE The silver and zinc used for mixing the alloys were 99.99 pct pure. The two components were weighed to within 0.1 pct of the weights required fo the alloy composition. They were then placed in a closed graphite mold and the mold and contents were heated in 100°C stages from 500&apos; to 900°C with sufficient time and vigorous agitation at each stage provided to dissolve the silver. The crucible was then heated to 1150°C and agitated violently before being quenched in oil. The resulting alloy rod was machined free of sur face defects and then placed in a graphite mold designed for growing single crystals. The graphite mold was closed with a graphite plug and was encased in a pyrex glass tube which was connected to a vacuum system. The tube and mold assembly were placed in a furnace; the tube was evacuated and the furnace was rapidly heated to a temperature sufficient for fusing and sealing the glass. The glass-encased evacuated mold and contents were then lowered through a vertical furnace. The top section of the furnace was held at 100 °C above the melting point of the alloy. The lowering rate was 1.5 in. per hr. The tension specimens were 1/4 in. diam; the shear specimens were 1/2 in. diam. These specimens were then removed from the mold, etched, and chemically polished with hot (60°C) Chase etch reagent (Crz03-4.0 g, NH4C1-7.5 g, NHOs-150 cc, HzS04-52 cc, and Hz0 to make 1 liter). In preparation for tensile testing, the specimens were carefully machined to a diameter of about 0.200 in. to permit a gage length of 6 in., annealed for 16 hr at 800&apos; to reduce coring, and then cleaned and polished. A modified Bausch-type shear apparatus which has been described previously18 were employed. The gage length was 1/8 in. This shear apparatus was placed in an Instron tensile testing machine. EXPERIMENTAL RESULTS A) Tension. Several specimens were extended at room temperature to determine the effect of initial orientation on the stress-strain curves of Ag-30 pct Zn. The initial orientation and the resolved shear stress supported by the active slip system at various total strains are plotted in Fig. 1. The critical resolved shear stress, t,, initial rate of work hardening, d/dy, and length of the easy-glide region are independent of orientation. The arrival at the symmetry line is shown by an arrow in Fig. 1. During the easy-glide region of the stress-strain

Jan 1, 1963

By O. N. Carlson, S. A. Bradford

Discontinuous yielding in tensile tests was observed in V-O alloys in the temperature ranges of 150° to 175°C and also 350° to 400°C. The magnitude and intensity of the serrations were found to vary considerably with oxygen content. Maxima were observed in tensile and yield strengths and in the strain-hardening coefficient at the higher temperature only. The strain rate sensitivity was observed to be negative between 150° and 400°C. THIS investigation was undertaken to study the effect of oxygen on the tensile properties of iodide vanadium in the temperature range of 25o to 450°C. Brown1 observed an increase in strength between room temperature and 400°C in vanadium metal, and found that oxygen and nitrogen had a rather pronounced effect on the strength and ductility. A maximum in the tensile strength was observed by Rostoker et al.2 near 300oC and by Pugh3 around 450°C for calcium-reduced vanadium. Pugh also found a maximum in the yield strength and in the strain-hardening exponent, and minima in the elongation and strain rate sensitivity at the same temperature. Eustice and Carlson4 reported the appearance of serrations in the stress-strain curves between 140° and 180°C in iodide vanadium containing 600 ppm O. These anomalies in the mechanical properties indicate that strain aging occurs in vanadium, but the impurity or impurities responsible for the above-mentioned effects have not been identified. The phenomenon of strain aging is usually characterized by the return of the yield point after interruption of a strength test. In the temperature range where strain aging occurs, the yield and tensile strengths attain maximum values, elongation and strain rate sensitivity exhibit minima, and discontinuous yielding is generally observed in the stress-strain curve. Cottrell5, 6 has postulated that strain aging is due to the migration of solute atoms to dislocation sites to produce locking after the dislocations have broken free from their impurity atmospheres during the initial yielding. At the strain-aging temperature the process is a dynamic one in which the solute impurity atoms diffuse to the vicinity of the moving disloca- tion producing "locking" which gives rise to maxima in the tensile strength and serrations in the elongation curves. Cottrel17 has noted that discontinuous yielding in iron occurs when the diffusion coefficient of nitrogen, D, and the strain rate, i, are related by D = 10-9 €. EXPERTMENTAL PROCEDURE The vanadium metal employed in this study was prepared by the iodide refining process as described by Carlson and owen.8 A representative analysis of the vanadium used in this investigation was: 150 ppm O, <5 ppm N, <1 ppm H, 150 ppm C, 150 ppm Fe, 70 ppm Cr, <50 ppm Si, 30ppm Cu, 20 ppm Ni, <20 ppm Ca, <20 ppm Mg and <20 ppm Ti. Alloys containing from 200 to 1800 ppm O, all of which lie in the solid solution range of the V-O system, were prepared by arc melting vanadium together with portions of a high-oxygen master alloy. The master alloy was prepared by tamping pure V2O5 into holes drilled in a vanadium ingot and arc melting this five or six times in an inert gas atmosphere, inverting the button between each melting step. The oxygen content of the master alloy was then determined by vacuum fusion analysis. Vanadium containing less than 150 ppm O was prepared in the following manner. A bar of iodide vanadium was deoxidized by sealing it in a tantalum crucible with a few grams of high-purity calcium. This was held at 1100°C for 4 days to allow time for the oxygen to diffuse to the surface and to react with the calcium vapors. The calcium oxide product was later dissolved from the surface of the bar with dilute acetic acid. In this way vanadium containing from 20 to 50 ppm O was prepared. Sample Preparation. The are-melted ingots were cold swaged into 3/16-in. diam rods and these were machined into cylindrical tensile specimens with a reduced section of 1.00-in. length and 0.120-in. diam. The test specimens were annealed for 4 hr at 900°C in a dynamic vacuum of mm of Hg to remove hydrogen from the metal. This recrystal-lization treatment produced a uniformly fine-grained structure with a mean grain size of approximately 0.06-mm diam. The oxygen contents reported in this paper were determined by a vacuum fusion analysis of the tensile specimens after testing. Analyses for other interstitial or metallic impurities showed no significant changes from that of the original material. Tension Tests. Tension tests were performed on a screw-driven tensile machine at a constant cross-head speed of 0.01 in. per min. Tests at elevated temperatures were carried out by heating the

Jan 1, 1962

By Klaus Detert

Fifteen and 18 pct Ni maraging steel and several binavy and ternary alloys of the iron-rich corner of the Fe-Co-Ni system have been studied. After annealing in the austenite range, these alloys were deformed slightly by cold rolling and subsequently aged. Compavison of experimental measurements at various processing stages indicates that small degrees of deforn~ation (5 to 10 pct reduction in thickness) do not influence hardness and strength or the aging kinetics. Electrical resistivity and ductility are somewhat redu]ced and the coercive force is substantially lower when compared to identical samples which were not deformed. The results are explained in terms of retained austenite which transforms into martensite with the small amount of deformation. RECENTLY there has been increasing interest in maraging steel for applications in electric power generators requiring a high ratio of power to weight.&apos; Fifteen pct Ni maraging steel has been investigated to evaluate its properties and performance for application as high-strength magnetic rotor steel,&apos; and a thorough investigation of the precipitation and transformation processes in this alloy has been conducted in this laboratory.3 The influence of deformation, which preceded the aging treatment, was also studied. It was found that a small deformation in the order of 5 pct has a rather striking effect in reducing the coercive force. Other interesting effects on the properties caused by such deformation have led to the more detailed studies reported herein. EXPERIMENTAL METHOD The methods used to produce the samples from 15 pct Ni maraging steel have been described elsewhere.3 The general procedure of hot forging and cold rolling to sheet has been followed. The composition is included in Table I which also contains the composition of the 18 pct Ni maraging steel grade 250 studied. More data about the material and the processing of the 18 pct Ni maraging steel have been recently reported.4 The experimental alloys of binary and ternary Fe-Ni-Co alloys were made by levitation melting in an argon atmosphere and casting into rod-shaped ingots 7 mm thick weighing 20 g. From these ingots 25-mm-long rods were machined to study the phase transformation by a dilatometer. These rods were then cold-rolled to strips, 2.4 mm thick. Annealing for austenitizing was done in tube furnaces in an argon or helium atmosphere followed by cooling in the water-cooled portion of the tube. Aging was done in a salt bath containing a neutral blend of Alkali nitrates and nitrites. Vickers hardness was measured using a load of 50 kg for 15 sec. Tensile tests were carried out on a hard beam tensile tester at a strain rate of 5 X lo-&apos; per sec using flat samples with a gage length of 37.5 mm and a cross section of 1.25 by 6.25 mm. Estimated sensitivity was 5 K x strain and 0.35 kg per sq mm stress. Magnetic saturation was determined on small cylindrical samples, 2.5 mm in length and diameter, by measuring the force exerted by the gradient of a magnetic field of 1000 oe per cm in a mean field of 11,500 oe. The measured values could be reproduced within *1 pct. Coercive force was measured by a precision-type magnetic field probe in a magnetic coil as described by Foerster.5 The magnetizing field was 1300 oe. The samples were 5 cm long, 1 cm wide, and 2.4 mm thick. he coercive force was measured to within +0.1 oe. Electrical resistivity was measured by using a potentiometer on flat strips with a gage length of 100 mm and a cross section of 2.5 by 0.5 mm. The accuracy of the measurement was 0.1 pct but the reproducibility of the measured specific resistivity among different samples was in the order of 1 pct. The method used to prepare the samples for electron transmission has been reported elsewhere.3 RESULTS Fig. 1 shows the influence of deformation after annealing on the resistivity, hardness, and coercivity. The samples were annealed for 30 min at 1000"C,

Jan 1, 1968

By W. A. Backofen, N. E. Paton

DEFORMATION twinning contributes to the plasticity of titanium and has been reported on {10i2}, {1121},{11221}, {1123}, and {1124} planes.&apos; Twinning on {1011} has also been reported in commercially pure titanium as a result of quenching from 1000&apos;, but no reports of such twins occurring as a result of deformation alone are known to the authors. In this study single crystals grown from iodide titanium were compressed parallel to the c axis over the temperature range 25 to 800°C. From it has come evidence that (10il) deformation twins are the most common type between 400" and 800°C. Crystals about 6 mm high with a rectangular cross section measuring about 3 by 4 mm were used in the tests. Chemical analyses showed them to contain 220 to 250 ppm 0 arid 10 to 15 ppm N. The long axes of the crystals were made parallel to the c axis while the sides were parallel to (i100) and (1120), as shown in Fig. 1. The crystals were compressed between polished alumina platens with no lubrication, in a vacuum of 2 x lom5 torr. Between 25&apos; and 300°C the predominant twinning mode was (11221, which is to be expected for this stress state. There was an abrupt change at 400°C, however, and from that temperature up to 800°C twinning took place almost entirely on (10i1 ). Twin planes were determined by the two-surface rnethd. Measurement of the crystal orientation within several (10i1) twins by means of polarized-light4 and transmission electron microscopy showed that the lattice reorientations were the same as those previously reported for the (10i l ) twinning in magnesium.&apos; This reorientation is consistent with The calculated (10il ) twinning shear for titanium is 0.10, while that measured from surface offsets on a (1150) face, which is parallel to the shear direction, was about 0.15. Slip within the twins, or in the matrix adjacent to the twins, probably accounts for the larger measurement. Slip in both locations was judged to have occurred from observations on foils in the electron microscope.

Jan 1, 1970

By Robert J. Willard

The scanning electron microscope (SEM), became commercially available in 1966. Embodying some unique features not provided by conventional electron microscopes, this new electron-optical instrument offers the scientific community a new way of observing the surfaces of materials. In rock mechanics research, the SEM should prove a useful basic tool in characterizing rock fracture on a very small scale and thus contribute to a better understanding of rock behavior at larger scales. This article presents one example of how the SEM is being applied to such research at the Twin Cities Mining Research Center operated by the U.S. Bureau of Mines in Minneapolis. This research center conducts theoretical and experimental studies on a broad range of mechanisms that induce disintegration by the application of energy to rock.1 Some of these studies are concerned with the relation of microstructure to rock behavior and are carried out mainly with the petrographic microscope. At the same time, however, the center recognizes that this relation must be studied through several orders of magnitude, from lattice-size units of rock-forming minerals to field-size rock units. The SEM fits this scheme by extending the capability of the petrographic microscope into smaller orders of magnitude. However, because its resolution is limited to about 200 A at 10,000x, the SEM is not capable of resolving lattice-size units, and hence a conventional electron microscope with a much greater resolution capability is necessary at this order of magnitude.

Jan 6, 1969

By F. L. Grammer

The analyses given in Table I. were made several years ago at my request at a plant using Lake ores. They are of two furnaces, one making basic, the other Bessemer pig— they gave 6 casts each in 24 hr., also two flushes of cinder between each cast. They are offered simply for the sake of reference as, so far as I know, it is unusual to find so frequent full analyses made and none are on record. The variations in manganese-content in the first and second flushes on the basic furnace are interesting, if no more than a freak—the first flush being invariably higher in manganese. The iron-content of the two slags from an average of 12 flushes shows: Basic. Bessemer. Per Cent. Per Cent. Total iron...................................... 2.85 1.70 Combined iron................................ 0.72 0.52 Free iron....................................... 2.13 1.18 The greater iron-loss in the basic slag, while known, has never heretofore been so clearly set forth. This may modify the arrangement for handling slag; heretofore usually determined by proximity of the dumping-heap. If a nearby heap is used on contiguous territory, in the past, tilting molten-slag pots were used. If the Pittsburg flood-records for 30 years are a fair criterion the government regulations were inadequate, and molten slag was dumped in such a manner as to throttle the Monongahela at the time of the spring thaws. At Pittsburg the slag, where it is carried to a distance, is frequently granulated in pits and then removed in cars to which it is conveyed by clam-shell buckets. This practice is also quite customary where the slag is intended for the manufacture of slag cement. The production of 500 tons of cast-iron daily means about 300 tons of- slag and at 2.113 per cent. equals 6.4 tons

Jan 1, 1914

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat&apos;s solution to obtain

By R. A. Stauffer

THE chief ore of lithium is spodumene, a lithium-aluminum silicate containing up to 3 pct lithium. The preparation of lithium salts from spodumene is costly because of the low concentration of the metal and the difficulty of separating it from the other alkali metals present. Dr. Kroll&apos;s and Dr. Schlecten&apos;s recent paper&apos; has reviewed various methods proposed for preparation of lithium. It will be seen from this paper that the methods proposed to date have required one or another of the lithium salts as a raw material. The high cost of these salts has been the chief item of expense in the lithium metal produced. This situation has made it interesting to investigate the possibility of producing the metal directly from spodumene. When spodumene is calcined at 1000°C in the presence of lime, lithium oxide is replaced in the ore as is evidenced by the fact that it may be leached from the reaction mixture with water.2 Free energy calculations suggested that lithium oxide might be reduced with aluminum or silicon and the lithium produced distilled from the reaction mixture by heating to about 1000°C in a vacuum. These facts taken together suggested that it might be possible to prepare lithium metal directly from spodumene by heating a mixture of the ore, lime, and a suitable reducing agent in vacuum and distilling off the lithium metal as formed. THE REPLACEMENT OF Li20 IN SPODUMENE A series of experiments were undertaken to determine the ratio of lime to spodumene necessary to free substantially all the lithium oxide present in the ore. The spodumene used in these experiments was supplied by Foote Mineral Co. in the form of powder of about 200 mesh. Analysis of the spodumene was as follows: [ ] Lime (cp -200 mesh) was added in various ratios to spodumene and thoroughly mixed in a ball mill. Two hundred gram samples of spodumene-lime mixtures were charged loosely in fireclay crucibles and held at 1000°C in a gas-fired furnace for 5 hrs. The product in each case was ground to pass 140 mesh and then placed in a thimble in a soxhlet extractor. Extraction with water was carried on for 6 hrs. After this period the extract was reduced in volume by evaporation in order to precipitate dissolved lime and was then filtered and titrated with 1/4 normal hydrochloric acid. After correcting for residual calcium oxide in solution, the alkali present was calculated as lithium oxide. The results of these experiments are shown in Table I and Fig I. At lime-spodumene ratios less than 1.5, the products were invariably fused. At the ratio of 1.5 and above, the product was loosely sintered with little evidence of fusion. When the ratio of lime to spodumene was three, replacement of alkali oxides in the

Jan 1, 1947

By George Kunz

(Butte Meeting, August, 1913.) THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World&apos;s Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely clue the eventual success of this eminently desirable reform, which lie has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.3

Jan 7, 1913

By N. H. Muhlenberg

IT is often a tedious matter to get a solution of pig iron or steel, for the determination of phosphorus, which is absolutely free from silica. Where pig iron rich in silicon is dissolved in hydrochloric or nitric acid in the usual procedure, it is necessary, not only to evaporate the solution to complete dryness, but to heat the dry residue for some hours in an air-bath to a temperature of about 120° C. The oxide of iron is thus rendered insoluble in nitric acid, and is only slowly dissolved by hydrochloric acid. In the method of determining silicon by nitric and sulphuric acid, described in the Transactions of the Institute, Vol. VII, page 346, and Vol. VIII, page 508, we obtain in one or two hours a solution of the iron in the form of ferric sulphate entirely free from silica, and containing free sulphuric acid. It occurred to us that this solution might be made available for the determination of the phosphorus by the molybdate method. The following experiments were tried with unsatisfactory results. 1st. The iron was precipitated by ammonia, the precipitate filtered, washed, and dissolved in nitric acid. 2d. The iron was precipitated as basic acetate and dissolved in nitric acid. 3d. The solution was neutralized by ammonia, and nitric acid added in small excess. In all these cases the phosphorus obtained by precipitating by ammonium molybdate and magnesia-mixture was too low. The following method was then tried with success. The filtrate from the silica and graphite was evaporated to small bulk and heated in a porcelain dish on a sand-bath, until fumes of sulphuric acid ceased to escape. The dry residue was taken up with dilute nitric acid and the solution precipitated by ammonium molyhdate. The phosphorus was weighed as magnesium pyrophosphate. The results were satisfactory. To save time, the original solution of the iron in nitric and sulphuric acids was evaporated to dryness and heated as before until

Jan 1, 1882

By J. A. Ede

The property of the Spring Valley Coal Company, situated in Bureau county, Ill., comprises something more than 30,000 acres of coal-lands, on which have been opened four mines, designated as Nos. 1, 2, 3 and 4. Figs. 1, 2, 3 and 4 are plans of the first three; and Fig. 7 is a view of the surface-plant at No. 4, the workings of which it is not necessary to illustrate, as this mine has been practically merged in No. 2. No. 4 shaft is only 500 feet from No. 2, and both are ventilated by the same fan, and are in the same circle of air-supply. In speaking of No. 2, we now include No. 4. The system pursued in all the mines is " long-wall advancing," and the shafts are all vertical. The seam worked is locally and commercially known, in the Illinois series, as No. 3; but its position in the geological series is that of No. 2. It averages in thickness about 42 inches, arid has no partings, but mines in rectangular lumps, which stand a large amount of handling before breaking. An analysis made from Colliery No. 1 gave the following : Per cent. Moisture,.......... 1.45 Volatile combustible matter,.47.27 Fixed carbon,.........41.97 Sulphur,.........2.46 Ash,....... .. .. .. 6.85 Plate 6 shows a photographic view of this seam. The staff seen in the view is 37 inches long. The table on page 188, recorded in my office, which I presume to be correct, may be of interest. The bottom is fire-clay, varying in thickness from 6 to 24 inches. It affords what is considered good mining-ground. The roof immediately above the coal is a dark shale, lying in small bands, from 4 to 9 inches in thickness. Between the

Jan 1, 1900

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By Dever C. Ashmead

FRom time to time metal-mine engineers have inquired why anthracitc mines and their preparators are rarely operated on the two or three-shift basis. The subject may be approached as affecting: labor, development, the underground workers, the preparator, the outside workers, capital, the supply account, power consumption, the storage of coal over various shifts, railroad car supply, and the market. Labor From the start, the adoption of a plan of three full-shift operations in a day would cause difficulty with the colliery employees, for they have never worked on that plan and would show their resentment by suspending work. Even if they could be induced to work according to this schedule they would not be as efficient, for they would be working more or less unwillingly at hours at which they are accustomed to rest. Operation on a three-shift basis would necessitate triple manning of each working place, and dissensions would arise between the men, for each shift would claim that the preceding shift had taken undue advantage and had not left as favorable conditions as it had found. To obviate these disputes it might be [necessary to let out the work to a contractor, who would hire his helpers to mine out the chamber, or breast. The state mining law requires that a miner be put in charge of each working place. To conform with this provision he would have to hire three helpers and two miners to mine the breast. The labor unions have been trying to abolish the subcontractor in mine work and any method of working that would cause his return, however innocent in purpose, would result in labor disturbances. It might be possible to form partnerships of three miners working a place together, but these men would be quite likely to have frequent dissensions as to the proportion of work performed by each shift. Only

Jan 1, 1923

By R. J. Linney

Reserve Mining Co. produces 5 million tons of iron ore pellets per year. The finished product runs about 65.50 pct Fe, with 7.75 to 8.00 pct SiO2. Less than 12 pct arrives at the blast furnaces smaller than % in. This plant was originally designed to produce 3.75 tons annually—not 5 million. To handle the increased tonnage a fifth fine crushing line was added, and some very minor changes were made. When production can be stepped up 33 1/3 pct without extensive additions or changes—within the short period of a year—basic engineering has been sound. Operators of the plant consider it the best design job they have seen or heard of, and competent authorities have said that start-up was quicker and easier than for any previous large-scale minerals beneficiation plant. One big advantage is the elbow room allowed. Generally speaking, there is an eternal conflict between operator and designer over space. The designer has his costs per cubic foot, and he is keenly aware that if he permits the number of cubic feet to rise unnecessarily, total costs will be too high. But this was a new operation, and on a large scale. There were no proven standards to go by. Realizing this, Reserve&apos;s engineers provided ample and efficient access to machinery, allowing extra space for unanticipated situations. In three years of production this planning has paid off handsomely. Gravity Flow Saves Time and Money: This plant is on a rocky hillside, the car dumper about 270 ft above Lake Superior. In locating buildings and placing machinery the designers mad= good use of gravity flow, at considerable financial savings. In the concentrator building from rod mills to filters, gravity carries the material between all stages of the operation except one—the closed circuit pumping of concentrate between cone classifiers and ball mills. Since no machine is located directly above any other, an observer can stand on the truck ramp adjacent to the offices and laboratory and see practically every phase of activity in the huge building. The first mill section started in August 1955. After a day&apos;s run several modifications were made on auxiliary chutes and launders where spillage had occurred. This procedure was followed for the first

Jan 1, 1960

By Juptner von Jonstorff

A discussion of the paper by Messrs. Jüptner von Jonstorff, Blair, Dillner and Stead, read by title at the Lake Superior meeting, but presented first at the New York meeting of the Iron and Steel Institute (October, 1904), and here published under a mutual agreement between the two Institutes. Correspondence. MR. R. HAMILTON (Glengarnock) wrote to say that it was known for many years, that unless certain precautions were taken in dissolving the sample, there was a liability to obtain a solution from which the ammonium-molybdate solution would not precipitate the whole of the phosphorus. In 1877 Blair and Finkiner independently attributed this interference to the presence of carbonaceous matter in the solution, derived from the action of acids on the combined carbon of the metal, and they directed that the solution should be prepared in such a manner as to destroy these carbonaceous compounds. This was practically effected by evaporating the acid solution to dryness and roasting the residue. Adolf Tamm, in 1884, accentuated the same view. There are methods founded on the above-mentioned observations which leave nothing to be desired in point of accuracy, but the evaporation to dryness with subsequent roasting and re-solution consumes much time, besides the minor inconvenience caused by large amounts of acid fumes. In 1888 P. W. Shinier suggested that the incomplete precipitation of phosphorus was due to incomplete oxidation of -.the phosphorus, and proposed to render all the phosphorus precipitable by oxidizing the solution with potassium permanganate, etc. Experiments were made to test the accuracy of this view (details will be found in the Journal of the Society of Chemical Industry, vol. x., p. 904), and the results obtained seem to-prove that it is the correct one. It was first proved that carbonaceous matter in solution did not prevent the precipitation of properly oxidized phosphorus

Mar 1, 1905

By N. H. Murlenberg, T. M. Drown

It is often a tedious matter to get a solution of pig iron or steel, for the determination of phosphorus, which is absolutely free from silica. Where pig iron rich in silicon is dissolved in hydrochloric or nitric acid in the usual procedure, it is necessary, not only to evaporate the solution to complete dry ness, but to heat the dry residue for some beam in an air-bath to a temperature of about 120° C. The oxide of iron is thus rendered insoluble in nitric acid, and is only slowly dissolved by hydrochloric acid. In the method of determining silicon by nitric and sulphuric acid, described in the Transactions of the Institute, Vol. VII, page 346, arid Vol. VIII, page 508, we obtain in one or two hours a solution of the iron in the form of ferric sulphate entirely free from silica, and containing free sulphuric acid. It occurred to Us that this solution might be made available for the determination of the phosphorus by the molybdate method. The following experiments mere tried with unsatisfactory results. 1st. The iron was precipitated by ammonia, the precipitate filtered, washed, and dissolved in nitric acid. 2d. The iron was precipitated as basic acetate and dissolved in nitric acid. 3d. The solution was neutralized by ammonia, and nitric acid added in small excess. In all these cases the phosphorus obtained by precipitating by ammonium molybdate and magnesia-mixture was too low. The following method was then tried with success. The filtrate from the silica and graphite was evaporated to small bulk and heated in a porcelain dish on a sand-bath. until fumes of sulphuric acid ceased to escape. The dry residue was taken up with dilute nitric acid and the solution precipitated by ammonium molyldate. The phosphorus was weighed as magnesium pyrophosphate. The results were satisfactory. To save time, the original solution of the iron in nitric and sulphuric acids was evaporated to dryness and heated as before until

Jan 1, 1882

By R. E. Mussler, F. E. Block, T. T. Campbell

An exploratovy study was made to deternzine the feasibility of preparing beryllium by the metallother-. mic reduction of beryllium oxide. The procedure involved heating a relatively nonvolatile metal reductant in contact with beryllium oxide in a vacuum. Beryllium vapors formed in the reaction were condensed as a coherent deposit on a heated surface. Reductants tested included tanthanun, yttrium, thorium, Th-Mg, and Zr- Ti alloys, and the hydrides of lanthaniir~z, yttriunz, and zirconiur?7,. Test ten7pevatures ranged from 1350&apos;to 175O&apos; C, and reaction times ranged frot 30 to 100 lzr. In most cases metal recoveries were lola, although yields close to 90 pct of theoretical were obtained with latzthanum, yttrium, and zirconium reductants. In most cases metal deposits were contanzinated by beryllides, /ls/cally of the Beln M or Bel3 M type. BERYLLIUM has a variety of unique properties including light weight (sp gr 1.85), low thermal neutron absorption cross section, high scattering cross section, excellent dimensional stability, high strength to weight ratio, high melting point (1285"C), high specific heat, and high thermal conductivity. Interest in beryllium as a structural material in aerospace and nuclear-reactor applications is based on these properties. In general, the potential of beryllium has been only partially realized, largely because of the brittleness of poly crystalline forms of beryllium, difficulties associated in its fabrication, and joining problems encountered in its use in structural applications. Several excellent books and monographs are available to those interested in the occurrence, extractive metallurgy, and utilization of beryllium.1"* Although an extensive amount of research on beryllium has been in progress during the past 10 years, much of the work has been concerned either with the so-called "ductility problem" or with the development of methods of fabrication and evaluation of properties of various commercial or purified grades of metal. A recent survey of the literature indicates that only limited efforts are presently being directed toward developing new methods for reducing beryllium compounds to metal. Two major commercial methods now used to produce beryllium are the magnesium reduction of beryllium fluoride and e lec trow inn ing of beryllium from fused sodium chloride-beryllium chloride salt baths. Only a limited amount of work has been done on the direct reduction of beryllium oxide. Major factors which complicate this method are the great stability of beryllium oxide and the reactive nature of beryllium metal. The stability of the oxide necessitates extremely high reduction temperatures and vacuum operation to liberate beryllium metal vapor and cause reactions of the following type to proceed: XBeO(s) +YM(s)-MYOX(s) + XBe(& As early as 1939, roll&apos; used this reaction for the direct reduction of beryllia by zirconium and titanium, and later in 1952 ~a~el~ studied the reduction of beryl-

Jan 1, 1967

By D. R. Walker, M. C. Shaw

THE laws of comminution of Kick and Rittinger have been debated for many years. Certain data obtained from ball mill and drop tests are found to be in approximate agreement with Rittinger&apos;s law while other data would seem to support Kick&apos;s law. In all these tests the energy required to produce a wide variety of particle sizes has been studied. Surface area has also been measured with considerable difficulty, at first because it was thought that the energy associated with crushing was that required to create new surface, later because of precedent and because a more fundamental variable was unknown. Tests made with the machine shop type of grinding process show that normally brittle materials that are usually crushed can behave like the more ductile metals. Brittleness is then a relative property largely dependent on specimen size and stress state. The machine grinding operation offers a convenient means for studying the comminution of materials in which the important size variable retains its identity. The energy required to grind a certain volume of material is shown to be strongly de- pendent on size. Kick&apos;s law is found to hold very well for particles below 1 micron in size, while Rittinger&apos;s law holds approximately in the comminution of larger particles. While a physical origin of Kick&apos;s law is established in terms of the theoretical strength of materials having a perfect lattice structure, there is found to be no physical basis for Rittinger&apos;s law.

Jan 3, 1954