Search Documents

By J. H. McCormick

This plant, near Marysville, Mont., was planned to treat the ore from the Piegan and Gloster mines, the latter being one of the early and famous producers of the Marysville district. When the mill was closed in 1888, treatment consisted of stamp milling, followed by pans and settlers for pan amalgamation. The extraction was evidently poor, because, a few years later, thousands of tons of tailings were re-treated by the ranchers in the valley below the mill, by the then new cyanide process, and gave a handsome profit. In 1914, the present owners, after laboratory tests and an experimental mill run, decided upon the following treatment: crushing to 40 mesh in cyanide solution, concentration, amalgamation, classification, and cyani-dation of sands by leaching, and of slime by agitation and decantation in charges. The ore averaged about $7 per ton, gold and silver, the ratio of weight being 1 oz. gold to 7.56 oz. silver. The ratio of gold and silver in tailings was 1 oz. Au to 36.6 oz. Ag; the quartz was sharp and sandy, however finely ground, and rather difficult to slime. The mechanical equipment was a No. 5 Symons gyratory crusher; three 10-ft. Lane slow-speed Chilean mills; one Wilfley roughing and one finishing table; one submerged-type Akins classifier; five 26 by 10-ft. fir leaching tanks; one 24 by 7-ft. Dorr thickener; four 14 by 16-ft. Dorr agitators; four 6-compartment double-row zinc-boxes having compartments 18 in. wide, 18 in. deep, and 34 in. long; Johnson zinc lathe; acid and vacuum filter tanks for treating precipitate; roasting furnace; and Case tilting No. 275 crucible furnace for melting precipitate. The mill is driven by electric power supplied by the Montana Power Co. at the following rates, per kw.-hr.: 200 to 300 hp., 0.68 c.; 300 to 500 hp., 0.61 c.; 500 to 750 hp., 0.55 c.; plus $1 per month per installed motor horsepower. The plant as above described was operated from May, 1915, to the end of the year, when an additional Dorr thickener and a 12 by 12-ft. Portland revolving filter were added, increasing the nominal capacity of 100 tons per 24 hr., but not the percentage of extraction. The combined treatment, at a cost of $1.48 per ton, saved 90 per cent. of the gold arid

Jan 1, 1919

By Sydney H. Ball

A QUARTER of a century ago, a pessimistic Belgian financier in conversation with the founder of the Belgian Congo, that great ruler, Leopold II, emphasized the danger to the colony should the synthesis of rubber be discovered. The king replied, "I do not worry. The Congo has had its ivory period; it now has its rubber period. Tomorrow it will have that of its mineral wealth; eventually that of agricultural products." That "tomorrow" arrived some twenty years ago. Through her mines the Belgian Congo has survived the present depression, and her mines for the next decade will safeguard her. The Congo, in turn. is the surest foundation industrially and financially of Belgium itself. In few, if any, political units is mining as dominant as in the Belgian Congo. In 1930, 1931 and 1932 mineral products represented respectively 67.9 per cent. 70.5 per cent and 59.3 per cent, of the total exports. In 1933 for each white person in the colony, there was produced about $1,675 worth of gold, diamonds, copper, tin ore and minor mineral products and in 1930 the per capita production, notwithstanding the larger population, was almost $2,000.

Jan 1, 1934

By P. H. Dudley

When we see the magnificent passenger-trains of from 8 to 12 coaches, drawn by locomotives weighing from 100 to 110 tons, at speeds of from 50 to 60 miles per hour between terminals, to make a schedule of 45 miles per hour, and freighttrains of from 50 to 75 cars of 60,000 pounds capacity, drawn by one locomotive, it is hard to realize that it lacks a few months of fifteen years since my pioneer 5-inch 80-pound rail for the United States was laid by the New York Central aid Hudson River Railroad Co., in July, 1884, on the Harlem line. Shorter passenger-trains, of from 4 to 5 coaches, are run much faster, notably the Empire State Express, the schedule of which for the 440 miles between New York and Buffalo requires 53.3 miles per hour, calling for a running-speed, for much of the time, of from 65 to 75 miles per hour, while higher speeds are very common. On other railroads laid with my 5 1/8-inch 80-pound rail, speeds of from 60 to 75 miles per hour obtain in daily practice. On many of the important railroads east of the Mississippi high speeds of from 60 to 70 miles per hour are part of the daily service. So many instances of speeds of 90, and even 100, miles per hour have been recorded that they must be considered as likely to occur on important lines, and provision must be made for them in the track. Solid mail-trains of from 6 to 8 cars are run from New York to Chicago, 1000 miles, in twenty-four hours; and, commeneing with the present year, shorter trains are running from Chicago to San Francisco, 2000 miles, in three and one-half days. In the freight-service equally important progress has been

Jan 1, 1900

By AIME AIME

ABOUT one hundred were in attendance when Donald M. Liddell opened the session* on non-ferrous metallurgy at 2 p. m. on Tuesday. F. F. Col- cord was vice-chairman. For the first part of the session the chair was turned over to Frank G. Breyer, who introduced G. L. Spencer, Jr., to read his contribution (T.P. 378), "High Silica Retorts at the Rose Lake Smelter," which was an account of the method of manufacture of high-silica zinc retorts at the Rose Lake smelter, and of the service given by these retorts. The materials used are, by volume, 50 per cent clay, 25 per cent silica flour and 25 per cent grog. Written discussion of the paper by E. M. Johnson, W. R. In- galls and M. M. Neale was read by Mr. Breyer. Mr. Johnson explained that their practice in manufacture differed very little from Rose Lake practice, but that their retorts did not last as long, possibly because Eagle-Picher does not use a hydraulic retort press or sintered ore. He ascribes the longer life of silica re- torts to the fact that they do not bend under heat. Mr. Ingalls pointed out that silica retorts are no better as heat conductors than clay retorts, but that they do have a superior rigidity in the furnace. The character of the retorts does not affect the density of the charge. Mr. Neale gave the procedure in the manufacture and use of high-silica retorts at the Donora zinc works, not

Jan 1, 1931

AN excerpt from the Odessa Isvestia Vechernia, dated April 24, 1927, and translated by P. Routzitzky, summarizes a report by Professor Preobragensky ad-dressed to the Russian Government. Professor Preo-bragensky writes in regard to newly discovered potash deposits in eastern European Russia. Near Solikamsk in the Perm district, about 100 miles east of the Ural mountains and on the Kama river, large deposits have been located and the belt has been traced southward about 25 miles. Subsequently the search for potash salts has been transferred to the Berezovsky district, near Nikolsk, on the Kosva river, about 70 miles north-east-of the city of Perm. Toward the end of March, 1927, at a depth of 800 ft., drilling at the Levensk salt works revealed potash salts in, definite strata. The bed has a thickness which extends from a depth of- 245 to 307 meters (latest data in middle of April, 1927) and has not been bottomed yet. Professor Preobragensky goes on to say that these operations have definitely, developed very large de-posits, the limits of which are still unknown. There is at least an implication that the reserves far exceed those of Stassfurt, Germany. For European use they are, of course, much less accessible, for by through rail they lie 1200 miles east of Petrograd. Further, no particulars are given as to the potash content. It is to be supposed that the salt occurs in the Permian beds that extend north and south along the west flank of the Ural mountains, as the localities mentioned .all lie within the area so mapped on the new geologic map of Russia issued by the Scientific and Technical Di-vision of the All-Russian Council of Soviets in 1922. It is interesting to note that these salt beds are of the same geologic age as those of 'the Stassfurt region and of the west Texas-New Mexico district, in which the U. S. Bureau of Mines is at present drilling.

Jan 7, 1927

Rossiter Worthington Raymond, Ph.D., LL. D-1840 to 1918.-Dr. Rossiter W. Raymond, Past President, Honorary Member and Secretary Emeritus, died suddenly of heart failure at his home, 123 Henry'St., Brooklyn, N. Y., on the evening of Tuesday, Dec. 31, 1918. He was one of the founders of the Institute and its second President. A Memorial 'Service will be held on Monday afternoon, Feb. 17. James Douglas.- The Institute suffered a second very severe loss by the death of Dr. James Douglas, Honorary Member, Past President (having served as President for two years), and in three separate respects the greatest benefactor of the Institute: first, in raising funds by volun¬tary subscription and his own personal gifts to pay the Institute's share of the money owed on the land on which the Engineering Societies Build¬ing now stands; second, as original donor to Engineering Societies Library; and third, by his bequest of $100,000 for the maintenance of the library of the American Institute of Mining Engineers. A resolution regarding the death of Dr. Douglas was passed by the Board of Directors and at the meeting of the Institute on Sept. 4, 1918, in Colorado, at which time a memorial service was held in the thea¬ter of the Hotel Broadmoor, attended by about 400 members and guests. A copy of the resolution was prepared and sent to the family. A bronze tablet is now being prepared and will be placed in the Members' Room and unveiled at the February meeting. A biography and portrait of Dr. Douglas was published in the September, 1918, Bulletin. There is also placed in the Engineering Societies Library an oil portrait of Dr. Douglas which had his own approval and was presented by him. American Institute of Metals.--During the Spring of the year, plans were completed with the American Institute of Metals whereby this society became the Institute of Metals Division of the American Insti¬tute of Mining Engineers. This body was a dignified aggregation of metallurgists which had been in existence for about 11 years. A bronze tablet commemorating the American Institute of Metals is now being placed in the Members' Room of the Institute, and during the year 1919 the Bulletin will bear the following title: "Bulletin of the American Institute of Mining Engineers, with which is consolidated the American Institute of Metals." Visits to Local Sections.-During the year President Jennings made visits to six of the Local Sections, on three of which occasions he was accompanied by the First Vice-president and the Secretary. First Vice-president Goodale made five visitations and the Secretary made eight.

Jan 1, 1923

By Webster, Wm. Reuben

THE greatly enlarged demand for small sizes of seamless copper tube which has recently occurred, due particularly to the rapid growth of the electric household-refrigerator industry, has emphasized the superiority of phosphorized to tough pitch copper for the purpose of producing this commodity. In the manufacture of this material exceedingly heavy reductions by cold drawing are employed, customary practice involving as much as 90 per cent. reduction of cross-sectional area in four runs without intermediate annealing. Although this superiority has long been recognized by tube makers, no quantitative expression of it has heretofore been published. It is believed that the data herewith presented mill serve this purpose. Recent investigators are not in agreement as to the relative mechanical properties of copper containing small amounts of oxygen as compared with copper containing sufficient oxygen to produce that condition known as tough pitch. Hanson, Marryat and Ford1 found that "oxygen has a relatively small effect on the properties of copper." Johnson, on the contrary, states "it cannot be denied that it (tough pitch copper) is inferior to deoxidized copper . . . where severe mechanical manipulation is concerned." These authorities in the reports of their investigations, as might be expected from their conclusions, do not present data of a character requisite to a conclusive determination of the question.

Jan 1, 1927

By LIONEL E. BOOTH

ORE tests are made for the purpose of determining the correct methods of treatment for any particular ore. They should be conducted so as to insure that the results obtained in actual mill practice, on ore of similar grade and physical nature, will duplicate the results obtained in the test work. As the expenditure of many thousand of dollars may be involved in the building of the necessary mill, the testing of ores calls for extreme care and skill in handling laboratory machines, and a knowledge of actual practice to guard against the danger of obtaining results in test work that would be impractical to duplicate on a commercial scale. The importance of a correct sample of the ore is at once apparent. No matter with what degree of care the test 4rk is done, it loses its value when made on an unrepresentative sample. It is the first safeguard against future disappointments in the loss of capital and time. A number of failures in the past have been traced directly to faulty or lax methods in obtaining the ore sample.

Jan 1, 1924

Trans. Pamphlet Volume Number Title Author Meeting and Page* 1033 Relation of Air Presaure to Drilling H. W. Seamon New York 66, 743. 766 Speeds of Hammer Drills . Feb. 1921 1034 Time Factor in Depletion of Mines J. W. Roberts New York 66, 711 Feb., 1921 1035 Calculation of Ore Tonnage and Grade J. E. Harding New York 66, 117, 122 from Drill-hole Samples Feb., 1921 1038 Diacuasion of Papers Presented in 1920 1041 Run-off and Mine Drainage H. N. Eavenson New York 66. 624. 630 Feb.. 1921 1043 The Health of the Underground Worker A. J. Lanza New York Feb, 1921 1045 Dust-ventilation Studies in Metal D. Harrington New York 66, 272, 288 Mines Feb., 1921 1046 Discussion of Papers Presented at New York Meeting, 1921 1072 Breakage and Heat Treatment of Rock- B. F. Tillson New York 66. 758 drill Steel Feb., 1921 1073 Discussion of Papers Presented at New York Meeting, 1921 1076-M Analysis of Some Drill-ateel Teats F. B. Foley New York 66,789 Feb.. 1921 1077-M Application of Magnetic Analysis to C. W. Burrows New York 66, -796 Rock Drills Feb., 1921 1078-M Heat Treatment of Rock-drill Steel G. H. Gilman New York 66.779 Feb., 1921 1080 What is the Ideal Drill Steel? F. H. kingdon New York 66, 807 Feb.. 1921 1081 Rock Drill-Steels, etc. W. T. Ober New York 66,814 Feb.. 1921 1082-C Underground Mine Development, Its J. B. Dilworth Wilkes-Barre 66,715, 761 Definition and Valuation Sent.. 1921 1081 Drill Steel from Hollow Ingots P. A. E. Armstrong New York 66,809 Feb., 1921 1068 Authors' Replies to Recent Discussion 1092 Heat Treatment of Rock Drill Steel A.E.Perkins New York 66,811 Feb., 1921 1096-M Octagonal Ventilation Shaft of Davis- J. L. Bruce Wilkes-Barre 66. 252, 608 Daly Copper Co. Sept., 1921 1100-C Determination of Electrical Equip- G. Bright Wilkes-Barre 66,580,606 ment for a Mine Hoist Sept., 1921

Jan 1, 1927

By JAMES SCULLY

For the last 4 years political leaders have found a new subject on which they can safely generalize wihout creating opposition. That subject is commodity prices. Since the four-fold increase in OPEC crude oil prices, public attention has focussed as never before on the subject of commodity prices. To advocate stabilizing commodity prices is akin to supporting motherhood or peace or better schooling. Everyone gives lip service to the concept that stable commodity prices are desirable. It is easier to state the principle than to achieve it. Prices that are stable in terms of one currency may be clearly unstable in terms of a different currency. This has become a troublesome matter since 1971, when the world's leading trading currencies were set free to float in relation to each other. To illustrate: consider copper prices in the interval between the end of 1974 and the end of 1977. During those 3 years, the copper price in pounds sterling on the London Metal Exchange rose by 25 per cent. During that period, however, in terms of the USA dollar equivalent, the price was unchanged. And during that period, in terms of the German mark equivalent the price shrank by 13 per cent while the Japanese yen equivalent fell by 20 per cent. Thus a price that appears stable in dollars, rose in terms of pounds sterling and fell in terms of marks and yen. Had this result been achieved as a consequence of an international effort to stabilize prices, an American would have said the effort was successful. An Englishman would have said it had failed to prevent a price rise. And a German or a Japanese consumer would have been happy to have covered his copper needs at a lower cost in terms of his own currency.

Jan 1, 1978

[Trans. No,PlaceDate Vol. Page1 1. Wilkes-Barre, Pa*May, '71 13 2, Bethlehem, Pa Aug., '71110 3, Troy, N. Y Nov., '71.. 113 4. Philadelphia, PaFeb,, '72.. 117 5, New York, N, Y.*May, '72,, 120 6. Pittsburgh, Pa Oct,, '72,, 125 7. Boston, Mass Feb,, '73.. 128 8. Philadelphia, Pa,*May, '73., 23 9. Easton, PaOct., '73., 27 10. New York, N, Y Feb., '74,, 211 11. St. Louis, Mo,*May, '74.. 33 12, Hazleton, PaOct., '74., 38 13, New Haven, ConnFeb., '75., 315 14. Dover, N. J,*May, '75.. 43 15, Cleveland, 0Oct,, '75,, 49]

Jan 1, 1928

By George Krauss, M. Cohen

The reverse martensitic transfomzation (i.e., the conversion of martensite to austenite on heating) was investigated in Fe-Ni alloys containing 30.5 to 33.5 wt pct Ni. The reversed austenite was found to be sufficiently distorted to exhibit marked differences in mechanical properties and to undergo recovery and re crystallization on further heating. In particular, the yield strength of the reversed austenite was as much as 2.5 times higher than that of the virgin austenite: with five cycles of the direct and reverse martensitic transformation, the yield strength was 2.6 times higher. There was an accompanying decrease in strain-hardening capacity and in stable ductility or uniform elongation. The recrystallization was observed to follow sigmoidal kinetics, but was characterized by an abnormal1y large temperature dependence which was evidently due to carbon segregation at the migrating grain boundaries. Upon recrystallization, the strength Properties reverted to those of the virgin austenite, but the ductility did not fully recover until the annealing temperature was further raised to dissipate the carbon segregation at the grain boundaries. The transformation of reversed austenite to produce second-generation martensite resulted in an unusually imperfect structure, thereby leaditg to additional strengthening. Horlleuer, the martensitic phase was much less responsive in this respect than was the austenite. MOST martensitic transformations are capable of undergoing a reverse transformation back to the austenitic phase on heating.&apos; This reaction, like the direct transformation to martensite on cooling, is usually athermal. In analogy with the Ms andMf temperatures for the martensitic transformation (where M, > Mf), the reverse transformation is characterized by the As andAf temperatures (where As<Af). It is well-known that the finish (Af) of the martensite-to-austenite reaction on heating may occur at a temperature where austenite is not stable relative to other phases in the equilibrium diagram.&apos; Reverse martensitic transformations have been found to influence the properties of the parent austenitic phase in a number of ferrous alloys. The austenite thus produced after one or more reversals is significantly altered in strength, microstruc-ture, diffusivity, and annealing characteristics compared to well-annealed, virgin austenite. The first detailed observations of such phenomena were made by Wasserman3 on an Fe-30 wt pct alloy. He found that the reversed austenite (i.e., austenite formed by the reverse martensitic transformation) was much stronger than the original austenite, and the second-generation martensite (i.e., martensite produced from the reversed austenite) was somewhat stronger than the first-generation martensite. On heating the reversed austenite, recrystallization occurred in a manner similar to that of a cold-worked metal; the Laue spots sharpened and the strength decreased.4 In recent years, Russian workers have shown considerable interest in these reverse martensitic transformations. Most of such investigations5-10 have been concerned with the stabilization of reversed austenite relative to subsequent martensitic transformation, and because of its unusual nature, this phenomenon will be discussed in detail elsewhere." On the other hand, the annealing behavior of reversed austenite and the attendant variation in properties have received little attention beyond the experiments of Wasserman.3,4 Gridnev eta1.,8 in one of the few such studies. followed the hardness change of reversed austenite as a function of time at three annealing temperatures. The marked strengthening of austenite achieved by the reverse martensitic transformation has been referred to as "transformation strengthening" by Wasserman3,4 and as "phase hardening" by Malyshev et a1.7,9,10 to differentiate it from hardening produced by cold working. Both groups of investigators noted that further strengthening of the austenite could be attained by repeated or cyclic transformations, but the first cycle resulted in the most pronounced effect. Evidence of the altered microstructure of reversed austenite has been reported by Maximova and Nikonorova6 and by Edmonson and KO.12 The former found that reversed austenite was much more sensitive to etching than the original austenite, and the latter authors observed a (&apos;ghost" structure resembling martensite in certain areas of the reversed austenite. Enhancement of the self-diffusion rate in reversed

Jan 1, 1962

By John Wellington Finch

WHAT is an engineering opportunity? To the mining .engineer the natural assumption is that the first requisite &apos;is a mineral deposit, but, of course, it is not so simple as that. There are at various points on the earth really very great mineral deposits which, on account of geographic location, backwardness of the country, or hostility of its natives, are now, and for a long time to come will be, quite valueless. The mining engineer, and for that matter the civil engineer, is more dependent upon the decisions of capital than upon any other factor in his profession. Ordinarily it is to be assumed that money will go to any place where it is clear that an adequate return upon its investment can be secured, but for many years it has not been safe to depend upon this. &apos; As already stated, there are many places where local conditions are such that mining is not safe to engage in and there are still other places in which conditions have been so aggravated by the Great War and by the social unrest which has upset the Asiatic region that capital is naturally most reluctant to venture, even when engineering data makes the undertaking appear attractive. It will be evident, I. believe, that there are many factors vital to the success of a mining enterprise in some of the remote countries which we do not have to consider in the United States and which do not, in fact, exist here.

Jan 1, 1924

By D. L. Rainey, E. R. Goter, W. R. Hudspeth

THE area in which spodumene-bearing pegmatites occur extends from Gaffney, S. C., in a northerly direction to Lincolnton, N. C., a distance of about 16 miles. The zone averages 2 miles in width. Interest in this area was first aroused by the discovery of small amounts of cassiterite in the peg-matites and in greissen which occurs on the walls of some of the pegmatites. Attempts were made from 1880 into the 1920&apos;s to mine and concentrate cas-siterite, but there were no successful operations. In 1935 L. M. Williams became interested in the area and began prospecting by trenching and sinking several small shafts. He gradually gained control of a considerable acreage south of the city of Kings Mountain, N. C. Mr. Williams states that he produced some ore from a shaft which he shipped to the Maywood Chemical Co. in the late 1930&apos;s. In 1937 G. H. Chambers of the Foote Mineral Co. visited the area and examined several properties, but the lithium market was too small to support the necessary concentrating plant. Early in World War II the Solvay Process Co., encouraged by various federal agencies, acquired the Williams properties and leases and started a drilling program to develop reserves for spodumene mining. A study of this area was also made under T. L. Kesler by the U. S. Department of the Interior Geological Survey. Starting in 1942 a concentrating plant, water supply dams, and shops and other buildings were constructed. The Superior Stone Co., a neighboring crushed stone operator, was awarded a contract to mine and crush the pegmatite ore. Late in 1943 the plant started operations, which were continued until February 1946. A drop in demand for lithium chemicals forced it to close and remain closed for several years. In 1948 the Foote Mineral Co. became interested in assuring itself a source of lithium ore on the North American continent, to be used in the production of lithium ore chemicals, and inspected properties in Canada, South Dakota, and North Carolina. The North Carolina deposits were the most promising. In the fall of 1950 the company leased the Solvay interests with option to buy and acquired additional properties. Renovation of the mill and preparation of the quarry for mining was begun in earnest in January 1951. A new crushing plant was built and construction started in July 1951. The flotation process used was developed in the North Carolina State Minerals Research Laboratory located at Asheville, N. C. Foote is now in the process of expanding its production. The crushing plant is being revamped and much of the old milling equipment purchased from Solvay will be replaced by new. Mining equipment of suitable capacity has been received and is in use. The frontispiece is a general view of the mill. The orebodies consist of pegmatite dikes composed of fine-grained albite and quartz, with varying amounts of mica and spodumene. The latter may amount to as much as 50 pct of the rock, but the overall average is about 15 to 20 pct. Tin, columbite-tantalite, beryl, and other valuable minerals are present in varying small amounts. These dikes, which intruded into the Roan Gneiss underlying most of the Piedmont area, strike approximately N 30 E and dip about 85" to the west. The gneiss has the same strike but dips about 70" west. The dikes lie in a belt extending from Lin-colnton, N. C., to Gaffney, S. C., and passing through

Jan 1, 1954

By Hansheinz Portisch, Harold Margolin

A surface expansion was found to occur sometime after etching in Ti-A1 alloys containing 9.5 to 12.5 wt pct Al. The structure formed, grew, and disappeared with tzrrze. The surface expansion was followed by microscope observations and interferometric and lattice parameter measurements. Activation energy measurements for the growth of the "expansion structure" and chemical analysis indicated that the phenomenon occurred as a result of hydrogen pzckup during etching. It is proposed that hydrogen initially enters octahedral sites of Ti3Al coherent with a Ti and later shifts to the tetrahedral sites. It is postulated that expansion occurs when hydrogen enters the tetrahedral sites. The expansion structure disappeared, it is proposed, because of diffusion of hydrogen from the surface into the body of the alloy and because of loss of coherency of Ti3Al. In examining Ti-A1 alloys, Ence and arolinl observed markings on the surface of specimens. These markings did not appear after electropolishing only, but rather appeared only after etching. The markings appeared to grow as a function of time after etching and later seemed to disappear. Although the markings had some similarity to precipitates, showing, frequently, a Widmanstatten type of arrangement, the observation that other microstructural markings continue to be seen within the new structure suggested that it was actually not a precipitate. The source of this structure was unknown and an attempt was made in the present investigation to develop some understanding of its nature. It has been labeled expansion structure. 1) EXPERIMENTAL PROCEDURE A) Alloys. Alloys in the range 6.5 to 14.5 wt. pct A1 were studied. Bars, 4 in. sq, forged from Bureau of Mines (73 Bhn) titanium consumably arc-melted 4-lb ingots,&apos; as well as 50-g arc-melted buttons of desired aluminum contents were used. The 50-g buttons also used Bureau of Mines titanium (73 Bhn) and aluminum of 99.99 pct purity. Buttons containing up to 8.5 wt pct A1 were hot-rolled from a furnace at 900&apos; . Those with higher aluminum contents were hand-forged on a titanium anvil, and heated with an oxygen-hydrogen torch in the region of 1200" to 1300°c. Frequent reheating kept the samples at the desired temperature range. After a reduction of about 30 pct, the samples were water-quenched. To eliminate any contamination picked up either during hot rolling or forging, at least 1 mil of the surface of the sample was taken off. B) Heat Treatment. Prior to heat treatment all alloys were vacuum-annealed to remove hydrogen. Samples were annealed at 900&apos; until a vacuum of 10&apos;5 mm Hg was established. After this treatment, the samples were wrapped in molybdenum sheet and heat-treated in argon-filled quartz capsules, which were broken under water or iced brine at the conclusion of the heat treatment. All heat treatments under dynamic vacuum were performed in a rapid-quench furnace. This consisted of a molybdenum-lined quartz tube attached to a vacuum system and through a stopcock to a beaker of water. At the completion of the heat treatment the vacuum stopcock was closed, the furnace shut off, and dropped below the quartz tube. Then immediately the inlet stopcock was opened and water admitted until the tube was filled. The steam formed was allowed to escape through the inlet stopcock. This method was used in heat treatments up to llOO°C. C) Metallography. Specimens for metallographic examination were ground, then electropolished using a Disa Electropol machine with a perchloric acid electr01te. Specimens were etched with R-etch.3 A standard etching time of 3 min was used, with the specimen being agitated during immersion. D) Sample Preparation for X-ray Analysis. Samples 0.2 to 0.5 mm in diam were produced from heat-treated rods which were turned to 2 mm diam on a lathe and then rotation-etched. An etchant consisting of 1 pt HF, 7 pt HN03, and 12 pt HzO was satisfactory. With the rod rotating in a vertical position at 50 to 100 rpm, a needle with uniform dimensions could be obtained. Care had to be taken to insure that the rod was at the center of rotation, otherwise cavitation developed. If a small unevenness developed, it was possible to grind it off with a fine emery paper. E) X-ray Diffraction. All X-ray work was done on a North American Phillips X-ray diffraction apparatus and a Jarrell Ash microfocus X-ray unit. The Phillips unit was used with a copper target and nickel filter. The Jarrell Ash unit was fitted with a cobalt target and iron filter. For the Phillips unit 35 kva and 20 ma were used, whereas for the microfocus unit with the 100-p fixed-focus gun 40 kv and 1.5 ma were used. It was found that alignment of cameras on the Jarre11 Ash unit was very critical. The X-ray beam contains an intense area which is not the beam center. The cameras were aligned with the intense region by monitoring the beam coming out of the camera with a Geiger counter. Adjustments were made until a maximum intensity was obtained. A Phillips diffractometer with a Brown chart recorder furnished some of the lattice parameter data. The divergence slit up to 80 deg 28 was I deg; above 80 deg, a 4-deg opening was used, while the scatter slit was1 deg and the receiving slit had a 0.003-in. opening. The general scanning rate was 1 deg per min, while peaks of special interest were rescanned at -j deg per min. For elevated-temperature X-ray diffraction a Uni-cam High Temperature Camera with a film diameter

Jan 1, 1969

Aamot, Olav Crone, Research Engr., Guggenheim Bros. Labs., 3,771 10th Ave., New York, N. Y. &apos;29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. &apos;04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. &apos;15 Abeel, George H., Jr., Cons. Min. Engr 128/ S. Canon Dr., Beverly Hills, Calif. &apos;18 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. &apos;28 Abel, Walter D., Cons. Engr 364 S. Cloverdale Ave., Los Angeles, Calif. &apos;32 Abele, Louis T 1457 Euclid Ave., Zanesville, Ohio. &apos;31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada. &apos;31 Abort, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. &apos;19 Abraham, W. E. V., East India United Service Club, 16 St. James&apos; Sq., London, S. W. 1, England. &apos;28 Abstain, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho. &apos;27 Acker, E. O&apos;C., Met 128 East Washington Late, Germantown, Philadelphia, Pa. &apos;86 Ackermat, D. E., Research Met., International Nickel Co., Inc. Bayonne, N. J. &apos;35 Acres, T. H., Geol. Dept., Valuation & Pet. Engrg., Richfield Oil Co., 555 S. Flower St., Los Angeles, Calif. &apos;29

Jan 1, 1934

By H. E. Lee, P. C. Feddersen, D. R. Gittinger, G. W. Dunn, J. B. Schuettenhelm

The new Bunker Hill slag-treatment plant, designed ior, a capacity of 300 to 400 tons of hot slag per day, was "blown in" April 5, 1943. In the ensuing I5-months period, 157,530 tons of slag was processed, with an average recovery of over go per cent of the zinc and practically all of the lead contained. In addition to this high metal recovery, utilization of the waste heat in the gas and fume venting, the process has enabled the generation of 231,376 tons of steam at 250-lb, gauge. Over the first six months opcration the volume of slag treated averaged somewhat under 300 tons per day. Reclaimed dump slag made up only about 1 5 per cent of the plant feed. In October 1943, preparations for the smelting of additional tonnages of dump slag were completed and the plant capacity was increased to an average of about 420 tons of slag per day. During the nine-months interval since that date, monthly averages of 450 toils per operating day have been maintained several times. The new plant (Fig. I) is constructed in close proximity to blast-furnace operations. The fuming furnace and other necessary equipment are housed in an eastward extension of the existing blast-furnace building. Beyond this housed extension the dust-laden gas is conveyed about the perimeter of a large rectangle formed by the flues, cooling towers and baghouses. The course of a 10-ft. balloon flue, which transports the fuming furnace gas, describes the west and south perimeters. This flue connects with a set of cooling towers located at the southeast comer. The flue and cooling-tower system serving the deleading kiln constitute the north side and the two baghouses, serving the kiln and furnace operations, -border the east side. From these baghouses the several discharge gas flows are come biped and conveyed in to the rectangle, being vented to atmosphere by means of a fan through a centrally located zoo-ft. brick stack. In general, the plant design and operation follow quite closely that dictated by experience gained in years of slag-fuming practice by the Anaconda Copper Mining Go., at East Helena, Mont., and the Consolidated Mining and Smelting Co. of Canada, Ltd., at Trail, B.C., and more recently by the International Smelting and Refining Co. at Toocle, Utah. : Fuming operations at the East Helena and the Tooele plants are more or less identical. Trail practice differs chiefly in the methods employed for the storage of the hot feed slag and in the methods utilized for the handling and cooling of the fuming furnace gas. The new Bunker Hill fuming plant closely follows Trail procedure in the treatment of the furnace discharge gas while East Hclcna methods have been adopted for the storage of feed slag.

Jan 1, 1944

By Mark R. Lamb

THE treatment of slime is of special interest to those engaged in cyaniding gold- and silver-ores. The usual practice is to make as small a percentage of slime as possible. In many instances the slime is given no treatment, but is impounded in dams in the hope that the future will develop some method of economically treating this product. The filter-press was the first step upward from ordinary decantation, but, on account of heavy labor-charge and high cost, its use has been limited to high-grade material. The slime at the Combination mill at Goldfield averages perhaps $20 per ton, and although the values are quickly dissolved the filter-press installation was not entirely satisfactory, resulting in the erection of the canvas-cell filter, developed by Chas. Butters and his staff. This filter is a great improvement over the filter-press, and the following description of it will be of interest to those engaged in treating slime produced in crushing ores, especially in view of the fact that, by the use of this filter, slime can be treated at a lesser cost and with a higher percentage of gold- or silver-extraction than in the ordinary treatment of sand; and, moreover, the initial outlay for an all-sliming plant is less than that for the ordinary sand- and slime-plant. The economy of construction of the Butters filter-plant is clearly shown in Figs. 1 and 2, which illustrate the 20-frame filter of 40 tons capacity, now being installed by the Nevada Goldfield Reduction Co. In this construction the slime-pump is so connected that it can pump to or from either tank or the filter by changing the valve-settings-a combination which is necessary in this particular installation, since sufficient fall is not available for filling and discharging the filter by gravity. Ordinarily, a slime-plant comprises: a filter-box with frames

Jan 1, 1907

By W. F. Boericke, T. H. Garnett

The Wisconsin zinc district, or the Upper Mississippi lead and zinc district as it is also termed, lies in the southwestern corner of Wisconsin, and embraces adjacent portions of Illinois and Iowa. It includes Iowa, Grant, and Lafayette counties in Wisconsin, and Jo Davies country in Illinois. In Iowa, Dubuque formerly produced considerable lead, but there has been little mining there in recent years. The map, Fig. 1, shows the entire district, withroads, railways, streams, and the various towns, or "camps," around which the mines are clustered. The hatchwork indicates the areas in which lead and zinc have been mined. The district is about 60 mi. (96 km.) north and south and about 40 mi. (64 km.) east and west. Not all of the territory is mineral bearing, and there are considerable areas that are believed to be barren. The grouping of the mines is patchy and irregular, though certain broad zoncs of mineralization extend almost the full width of the district, as from Mineral Point west through Mifflin and Livingston, and from Shullsburg west through New Diggings and Hazel Green. It is worth noting that the best mines of the district have, to date, been found within 10 mi. ease or west of the fourth principal meridian line, thus lying within a long, narrow, north-and-south belt extending the length of the district. In a field as large as the Wisconsin, which has only within comparatively recent time been worked intensively for zinc, the chances are good for opening new and important orebodies in parts of the district not yet, or insufficiently, prospected. However; the prospecting has been most successful around, or adjacent to, the old lead diggings of nearly a century ago, and the camps that were well known then are still centers of activity. In their order of importance they are: New Diggings, Ben-ton, Mifflin-Livingston, Galena, Linden, Hazel Green, Shullsburg, and Highland. The district is one of the best farming districts in Wisconsin, with deep fertile soil. The farms are large and well improved, and the towns are modern and prosperous. Railroad facilities are good and proximity to Chicago is an asset. Mining is usually done on a leasing system of 10

Jan 1, 1920

Charles H. Morgan, Worcester, Mass. (communication to the Secretary): In connection with Mr. Douglas&apos;s mention of the continuous charcoal kiln used at Kopparberg, some further data concerning this important invention may be of interest. Before giving these, however, I will say a word or two concerning other features of Swedish practice. In 1894 I spent two days at Soderfers with Mr. Tom Bergendal, the manager of the works, and was specially interested in the gas-producers and wood-drying kiln, illustrated in the paper contributed to our Transactions by Mr. Odelstjerna in that year.* The wood-drying kiln is, however, quite different in design and construction from Ljungberg&apos;s charcoal kiln. In the summer of 1894 it was discovered that by placing the gas-producer as close as possible to the open-hearth furnace, and working the producer hot, ordinary weather-dried wood, still containing a considerable percentage of moisture, could be used to advantage in the melting-furnace. Hence, the dryingkiln was needed for wet wood only. One of the iron-works of the Udeholm Go. was the first to adopt the Lundin saw-dust gas-producer and condenser, enabling them to make gas from saw-dust containing 45 per cent. of moisture, and convey the gas from the condenser through wooden pipes to the Siemens steel-melting furnace.† This sawdust gas gave very satisfactory results in iron-works; but the proprietors experienced much trouble by reason of the pollution of rivers by the tar-water from the condenser. On my visit, in 1894,I found that the Udeholm Co. had put in for their steel-melting furnaces the same wood-gas producers

Jan 1, 1899