Search Documents

By Fernando Guevara

Many smelting and slag-cleaning furnaces operate with cooling systems designed to freeze a slag layer over the refractory to protect it. The fluid flow and heat transfer conditions associated with the freeze layer and mushy zones are poorly understood. These phenomena were simulated with a small-scale room temperature, 2-dimensional model, using an aqueous solution of calcium chloride to simulate the slag. Reasonable similarity with conditions encountered with copper and nickel smelting systems was achieved (Pr 50 and Ra 108, in the laminar-turbulent transition). Measurements of the freeze layer development and velocities were made with the Particle Image Velocimetry (PIV) technique. Direct Numerical Simulations (DNS) were also made of the unsteady fluid flow and heat transfer problem. It was found that the solidification process is well described using an improved model for high molecular viscosity in the mushy zone. Solid front growth, isothermal profiles, velocity profiles and heat transfer through the walls showed good agreement between the PIV and DNS results. Experimental and numerical velocity profiles close to the freeze layer show a parabolic behaviour in the vertical velocity profile which is completely different from the calculation of heat transfer using a sharp interface model. The reason for this is attributed to the effects of the mushy zone with a high viscosity and high shear stresses acting on that area.

Jan 1, 2006

By Liping Li

A comprehensive three-dimensional two-phase mathematical model was developed to represent a channel type reactor with intense bottom gas agitation. Tracer dispersion and particle tracing methods were used to conduct the analysis based on the solution of the Navier-Stokes equations. Different operational parameters, such is gas volume flow rate. bubbler separation aspect ratios and liquid Input flow rates, were investigated for the purpose of reactor optimization. The numerical calculations were compared with experimental results obtained at the University of Missouri and a good general agreement was observed. Relatively low longitudinal mixing was observed characterizing the system as a "plug-flow" type reactor, in contrast to the intense vertical mixing, under the conditions investigated. Some general mixing characteristics are also discussed In connection to the behavior of other metallurgical reactors.

Jan 1, 1996

By Jeffrey F. Adams

Gypsum fouling is a common problem in the hydrometallurgical industry. It is a particular problem in free sulphuric acid neutralization, or iron removal operations where sulphates are removed from aqueous solutions by the addition of calcium-containing bases. Previous work revealed a strong correlation between the degree of gypsum supersaturation in the reactor and the rate of scale growth indicating that scale formation and growth are primarily controlled by chemical phenomena. However, the chemical behaviour of gypsum is variable and unpredictable with solution chemistry and temperature. Many of the "rules of thumb" that are used to predict its behaviour (and avoid fouling) are in fact based on gypsum solubility in water, rather than on real mixed metal sulphate systems. However, despite this unconventional solubility behaviour, we have been able to accurately model it in Ni, Mg, and Zn containing solutions over a wide range of temperature (25°C-90°C) and solution concentration (0-6 m) using the OLI simulation software. Furthermore, by studying fouling rates in a simulated continuous neutralization reactor, the relationship between process conditions and fouling rates were explained for the first time. This has led to an understanding of how techniques for minimizing gypsum fouling work.

Jan 1, 2003

By Nathaniel Arbiter

The first ammonia leaching plants, applied to copper carbonate and native copper tailings in 19 15, were followed more recently by research and development of flowsheets for ammonia leaching of sulfide concentrates. These were applied to two commercial plants. Anaconda's Arbiter Plant started up in 1974 with a design capacity of 36,000 tons/year of cathodes, to be produced by ammonia leaching with oxygen, followed by solvent extraction and electrowinning. The plant shutdown in late 1977 as a result of high maintenance and operating costs, partly due to harsh winters; to complications associated with sulfate disposal; and to changes in mineralogy. BHP's Coloso plant in Chile was designed to produce 80,000 tons/year of cathodes by leaching part of Escondida's concentrate production. Using a similar flowsheet but with air and low temperatures to avoid sulfate production, it started up in late 1994 and shutdown in mid-1998, after failing to reach cathode design capacity, and experiencing problems with its technology. The paper reviews the technologies and also alternative methods for overcoming the problems.

Jan 1, 1999

By J. Murphy

The economics of microbial coal desulfurization are affected significantly by the proper selection of the plant site and by maintenance of variables at suitable levels. High sulfur coal particles below 200 mesh show sulfate production rates triple those with 150 mesh coal but grinding costs are greater. Slurry solids density increases from 5% to 20% reduced the rate constant by a factor of 10. Coal added to a batch reactor in the stationary phase resulted in a sudden second exponential sulfate production phase indicating feasibility of lower cost continuous operation. Successful operation in the absence of beef broth, yeast or added nutrients at non-sterile conditions enhanced projected economics. Finally, the need for adequate agitation and aeration was well established.

Jan 1, 1985

By A. N. Lasseigne

Hydrogen storage capabilities of LaNi5 intermetallic compounds were investigated utilizing the combination of thermoelectric power, Beeghly Ester-Halogen digestion, and Leco hydrogen determination. Thermoelectric power has demonstrated a rapid hydrogen assessment capability and can achieve the equivalent of the pressure-composition-temperature (activity) diagram. Effective use of hydrogen storage materials occurs in the two-phase, alpha+beta region of the PCT diagram. A thorough assessment of the content of each phase in this two-phase region to optimize performance of the hydrogen storage materials is described. Practices using the combination of these three analytical practices for rapid characterization of LaNi5intermetallic alloys are discussed.

Jan 1, 2006

By Ennio Bonetti

The technological applications of MgH2 hydrides for hydrogen storage demand the overcoming of some critical issues: an improvement of the reaction kinetics and a reduction of the desorption temperature. The synthesis of nanocrystalline MgH2 by reactive milling and inert gas condensation and a proper metal catalyst addition, constitute recently employed strategies. In the investigation of the hydrogen short and long-range dynamics, sorption kinetics and nanostructure stability, the mechanical spectroscopy offers some specific advantages. In the present research this technique was employed with other experimental approaches (XRD DSC) to investigate relaxational and structural damping processes in nanocrystalline MgH2 with added catalysts (Fe). Time/temperature variation of the dynamic elasticity moduli and mechanical quality factor are correlated to hydrogen anelastic relaxation processes and concomitant structural transformation of MgH2 to Mg associated to long range H diffusion. Results are discussed with reference to microstructural modification strategies able to assist hydrogen release.

Jan 1, 2006

By M. G. King

In 1982, Asarco operated six smelters and refineries producing primary copper, lead, zinc, silver and gold. At that time Asarco was still reliant on its custom smelting and refining roots and mined only 25% of its smelting and refining capacity for copper and 10% of its lead smelting and refining capacity. By 1992, Asarco had been reshaped to become largely an integrated primary metal producer operating four smelters and three refineries. Zinc is no longer refined and the mining capacity has been increased to meet 100% of copper smelting and 50% of lead smelting needs. Only one custom smelter is in operation. This paper describes the metallurgical changes and challenges which have occurred in this restructuring of Asarco's operations while maintaining Asarco's position as one of the largest non-ferrous metals producers in the world.

Jan 1, 1993

By E. Morrice

Solubility of yttrium oxide (Y203) in fluoride melts was experimentally measured in the temperature range of 998 to 1273 K and, YF3 composition in LiF.YF3 melts varying from 20 to 50 mole pct using a graphite crucible in an argon atmosphere. Solubility of oxide in the melt was found to increase with increasing temperature and YF3 composition in the melt. An expression for in XY2O3 as a function of temperature for several melts was deduced. The calculated activity coefficients of Y2O3 in the melts exhibited a negative deviation from Raoult's law.

Jan 1, 1989

By Takeshi Yoshikawa

For the development of low-cost silicon refining process for solar cells, the present authors have been studying the low temperature refining technique, ?solidification refining of Si with Si-Al melts at 1173 ? 1273K?. In the present work, we have investigated the B removal in that refining, utilizing the segregation effect and also the effect of Ti addition to the melt. Segregation ratio of B between solid Si and Si-Al melt was measured by the temperature gradient zone melting technique and it indicated the B removal fraction would be as much as 90%. Titanium addition to the melt was found to produce the TiB2 precipitation with soluble B in that melt and bring the effective B removal of refined Si to its content of 1ppma.

Jan 1, 2006

By Gretel Parker

In situ Raman spectroscopic investigations of copper iron sulfides in leach solutions have been undertaken. Coupling potentiodynamic techniques to Raman spectroscopy produces a powerful tool for studying mineral surface response to changing conditions, while ESEM and high-vacuum techniques provide complementary ex-situ information on surface structure and composition. Oxidative acid leaching of chalcopyrite at ambient temperature yielded a product with S-S bonds that were shifted from those seen with covellite, with little evidence of elemental sulfur formation. Leaching of chalcopyrite led to non-homogeneous product distribution. Raman spectroscopy was able to identify the products formed on the mineral surfacein situ while leaching was occurring. Raman mapping and imaging demonstrated a surface distribution of the products which can be related to composition and structure changes of the mineral surface. The surface formed on chalcopyrite after anodic oxidation at 0.570 V vs. Ag/AgCl in 0.1 mol dm-3 HCl undergoes laser-induced transformation.

Jan 1, 2003

By Emily Chen, Randolph Kirchain, Gabrielle Gaustad

"As prices and demand for aluminum metal have increased over the past few years, secondary production has begun to outpace primary aluminum production. However, while recycling of packaging and automotive scrap has continued to increase, aerospace secondary materials remain a largely untapped resource. Shredded or co-mingled aerospace scrap has a high degree of compositional uncertainty due to the prevalence of high copper and high zinc alloy series. Although it is clear that upgrading strategies enable increased usage of aerospace scrap, it is not clear that they would be economic or efficient. Previous studies by the authors have shown that modeling techniques, specifically chance-constrained optimization, provide the ability to evaluate upgrading options in terms of potential aerospace scrap utilization and production cost. Three specific cases are analyzed: a dismantled case, a sorted case, and a shredded or co-mingled case; sensitivity analysis of resulting compositional uncertainty is also presented.IntroductionAluminum recycling has a number of key environmental and economic benefits. Secondary recovery forestalls depletion of non-renewable resources and avoids the deleterious effects of extraction and winning (albeit by substituting some effects of its own). For most metals, the latter provides strong motivation for recycling; for light metals, like aluminum, the motivation is compelling[1]. Fortunately, as prices and demand for aluminum have increased greatly over recent years, secondary production has begun to outpace primary production (Figure 1). However, while the recycling rates of many aluminum products such as used beverage cans and cars have increased over this period, aerospace secondary materials remain a comparatively untapped resource.This untapped resource for scrap aluminum is a very large one; aluminum is the primary aircraft material comprising about 80% of a planes unladen weight[2]. It is used extensively for airframes, landing gear, engine components, propellers, and interior trim. A standard Boeing 747 jumbo jet, for example, contains approximately 75,000 kilograms of aluminum[2]. At an approximate rate of 300 per year, more than 6,000 civil aircraft are forecast to arrive at end-of-life in the next 20 years, potentially creating a large aerospace scrap market[3]. Many military aircraft are already available for possible scrap use, however, most are currently in storage at air force bases around the world[4]. The underutilization of these aerospace scrap materials indicates a lack of economic end-of-life options."

Jan 1, 2008

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003

By K. S. Kumar

FLS miljø, Inc. markets, designs and supplies particulate collection devices for dusts, fumes, and mists; In this paper, the application of both wet and dry electrostatic precipitators (ESPs) in smelting, and roasting plants is discussed.

Jan 1, 1998

By M. Vijayalakshmi, S. Saroja, C. Sudha, T. N. Prasanthi

"Ti-5Ta-2Nb alloy and 304L austenitic stainless steel were joined by explosive cladding process. Investigations on 'as received' explosive clad revealed high hardness very near the interface due to martensitic transformation of 304L steel base plate. To improve ductility, explosive clads were heat treated in the temperature range of 823 to 1073 K for 1 to 20 h. Consequent change in the microstructure and microchemistry of the clad interface was studied. No change in the interface microstructure was observed for heat treatment at 823 K. Increase in temperature lead to the formation of various reaction zones at the interface, their number and width increase with temperature and time of thermal exposure. Growth kinetics of the reaction zones was monitored and activation energy required for formation was calculated. From elemental redistribution profiles, effective inter-diffusivities of alloying elements were calculated as a function of concentration and activation energy required for inter-diffusion was evaluated.IntroductionFor engineering components exposed to highly oxidizing and corrosive environments, a titanium based alloy i.e Ti-5Ta-2Nb (Ti-Ta-Nb) is often chosen as a structural material [1,2]. For economic consideration, vessels and piping exposed to non-oxidizing conditions are fabricated from 304L austenitic stainless steel (304L SS). Hence, dissimilar joint of Ti-5Ta-2Nb alloy and austenitic stainless steel becomes unavoidable. Fusion welding processes are not suitable for joining Ti and Fe based alloys due to the propensity for the formation of intermetallic phases and subsequent reduction in the bond strength [3,4]. Hence, explosive cladding, a solid state welding technique, was used to achieve high integrity, corrosion resistant joints between the two alloys."

Jan 1, 2012

By Emilia Visileanu, Eftalea Carpus

"The strategy of developing the Romanian textile industry sub-sectors envisages the achieving of certain superior production indices, from a physical and value point of view, in 2010, a quantitative increase of textile wastes by 14% in 2010 as compared to 2000, implicitly. The percentage of the turned-to-profit wastes will have an increasing tendency, from 53.6% in 2000 to 74.7% in 2010. The article synthetically presents the innovative elements of the technology of processing the industry textile wastes.1. Introduction“People will need to re-adopt this sense of rarity that has been forgotten over the last two centuries. Humans need to collect, sort, recover, going back to the old ideal of alchemists: complete the material cycle, turn waste into resource, reduce all forms of predatory behaviour as much as possible”Irrespective of the historical period, geographical positioning, economic power or employed technologies, wastes resulted and will result in a bigger or smaller quantity as long as life and activity on Earth go on. The negative effects of these over the environment factors and implicitly over population health are well known all over the world and not approaching this matter enough may have catastrophic consequences over life. Having in view these aspects, finding solutions for diminishing the general waste quantity and limiting the negative effects of those products is important, by effecting the reusing of the recyclable ones in the production processes as secondary raw materials, and by ecologically treating and storing those than cannot be reused.2. Experiments and researchesThe textile industry affects the environment by the high water, energy and chemical consumption, as well as by the high quantity of wastes that are the result of using an impressive number of chemical substances and technological processes.The development strategy of the Romanian textile industry sub-sectors foresees, for 2010, the achieving of certain higher production indices as compared to 2000, both in terms of materials (as merchandise) and in terms of value, which implicitly leads to a quantitative increase of wastes.The flexible, economic and ecologic technologies which include systems of waste preliminary preparing (cutting, opening) and conventional or non-conventional system of processing the recovered fibres lay at the basis of substantiating the activity of implementing the notion of zero wastes."

Jan 1, 2008

By Klaus Gamweger

There are different reasons for purging a metal bath. The operations are varied, for example the purging gas can be used as a reactive gas being part of the metallurgical process or as an inert gas using the rising gas bubbles for agitation only. The different purposes for agitation, chemical and thermal homogenization or a preferential movement of the slag to the slag skimming door have to be considered. It depends on the furnace type and its dimensions as well as the process characteristics what the focus is on. For an optimized arrangement of numbers and position of all single plugs in the furnace, mathematical modeling - the CFD Computational Fluid Dynamics method - is used. This paper shows how the operation of purging plugs can influence the metallurgical process of an anode furnace by the example of Jinchuan Copper in China. The potentials for savings in energy consumption as well as in time for oxidation and reduction are presented.

Jan 1, 2006

By H. Aminian

Copper electrowinning (EW) is an important process in connection with the solvent extraction to produce pure and marketable copper cathodes. A phenomenological model was developed to simulate the copper electrowinning process. The simulator is used to predict the operation of the Mines Gaspe pilot plant electrowinning cells put in operation in 1996. Results confirm the potential of the simulator that would subsequently be used for student training, process optimization and assessing the performances of control strategies.

Jan 1, 1999

By L. Salinas

Lance injection of gas and particles into a molten bath is currently practised in metallurgical processes (Mitsubishi lances for example). Several experimental and theorical studies have been conducted in the past on this topic. However, neither detailed calculations nor experimental studies of local flow patterns have been published. In the present work, a numerical simulation of the interaction of a gaseous vertical descending jet and a liquid surface was done, using the turbulence k-e model. There is a fair agreement between the calculated and the experimental values. The results of this study demonstrate that it is crucial that the gas jet velocity profile and turbulent characteristic are correctly formulated in order to correctly simulate the system.

Jan 1, 1999

By Peter Forschner

Classical Mixing Theory is based on applying many fundamental correlations to standard baffled dished bottomed vertical cylindrical vessels with high degrees of symmetry. Horizontal autoclaves operating at elevated temperatures and pressures have been used for more than two decades. All compartments and especially the first and last compartments are asymmetrical. To date no comparison of the effects of the asymmetric geometry on mixing system design and scale-up has been published. The results of investigating solids suspension, mixing time, momentum transfer from the impeller to feed slurry and feed inlet location in the first autoclave compartment are presented as influences on residence time distribution. CFD modeling was developed and verified with the test apparatus.

Jan 1, 2003