Search Documents

By Donna Post Guillen

"Cyclopentane, a flammable hydrocarbon, is being considered as a working fluid for waste heat recovery applications using Organic Rankine Cycles with Direct Evaporators. A postulated failure mode consisting of a pinhole leak in a heat exchanger tube raises safety concerns due to autoignition of the working fluid. Experiments were conducted to determine the ignition delay time (IDT) of cyclopentane using an Ignition Quality Test™ (IQT™) device. Two sets of experiments were conducted per ASTM D6890 (with exception to charge pressure and temperature) to determine ignition delay of the fuel at atmospheric pressure for standard air (-20.95% oxygen) and vitiated air (13.3% oxygen) at a temperature of 803 K. Operation of the IQT device at a much lower pressure (1 bar) than normal operation (21.4 bar) with a standard injector led to very rich conditions and wetting of the stainless steel chamber walls. Catalytic effects are postulated to produce the small IDTs observed. Experiments were repeated with a modified injector to prevent wall wetting, resulting in average IDTs that are substantially longer.IntroductionCyclopentane is being considered for use as a working fluid in a Direct Evaporator of an Organic Rankine Cycle (ORC). In this configuration, the heat exchanger is placed directly in the flow of the hot exhaust gas, rather than using a secondary heat transfer loop to isolate the flammable working fluid from the heat source. This configuration offers the advantages of approximately 15% lower cost and improved efficiency over a standard ORC. However, placing a heat exchanger operating with a flammable hydrocarbon in the hot exhaust gas stream presents potential safety risks. If a pinhole leak were to occur in the heat exchanger, working fluid could leak into the hot exhaust stream. Gas turbine exhaust is provided to the Direct Evaporator at a temperature of approximately 803 K, whereas the autoignition temperature of cyclopentane is 634 K (Gallant and Yaws, 1993). Autoignition of the working fluid has been identified as the key risk for this type of system.Autoignition occurs when sufficient self-heating by chemical reactions takes place to accelerate reaction rates to produce full-scale combustion. This is in contrast to forced ignition, in which an external source (e.g., spark) is employed to initiate the combustion process. For combustion to occur, the fuel to oxidizer concentration must be between the lower (lean) and upper (rich) flammable limits. The reaction rate depends on the species concentration of the fuel and oxidant, the local temperature and pressure. Ignition processes are comprised of steps that take a fmite amount of time. This latent period prior to the start of combustion is referred to as ignition delay time (IDT)."

Jan 1, 2012

By José Roberto de Oliveira

Based on literature review one can see that the main objectives of MnO reduction is the comprehension of slag interactions and reactions with other elements beyond carbon. That's because it is worthwhile to study pure MnO reduction, where there will be not oxides interaction and just carbon will be the reduction agent. By a thermodynamic analysis we know that Si can react with MnO, then it's important to study this influence, so as Mn content. Our work aims to develop kinetics parameters for the MnO reduction, varying Mn and Si contents in bath. This has been given by pressure measure of CO in a Fe-C bath. The CO is generated by the oxide reduction with carbon. It has been proved that: - Mn content decreases the MnO reduction; - the MnO reduction is mainly influenced by Si content in a bath containing Iron, Carbon and Manganese so as Silicium

Jan 1, 1997

By Ho-Sang Sohn

Copper concentrate particles of 200 to 300 mesh size were fed from the top of vertical reaction tube of 2.8 cm ID and 2 m long with an O2-N2 gas mixture. The reaction tube was heated to 900 K to 1100 K. The residence time of the particles in the reaction tube was about 1 second. The copper concentrate particles were very rapidly oxidized and melted down during their descent in the reaction tube. The particle temperature were calculated by combining an un-reacted core model, mass transfer between gas and particles, and heat transfer between gas, particles and tube wall. The particle temperature reached its maximum within a distance of 60 cm from the top of reaction tube, and it attained at 2000 K at higher oxygen partial pressure. The most particles were melted at the oxygen partial pressure above 20 kPa. An appreciable amount of As, Sb and Pb in the concentrate particles was eliminated in the upper portion of the reaction tube and the rate of elimination are explained by the rate of mass transfer of volatilized species through the gas film on the particle surface and the variation of particle temperature during the descent.

Jan 1, 2006

By R. Upadhyaya

Aluminium alloy matrix cast composites have been synthesised by incorporating fine graphite powders (0.5 - 20 µm size) and chopped carbon fibres (6.5 pm P). 3-6 mm length) by liquid metallurgy technique. Incorporation of these second phase materials exceeding 6-8 wt% invariably resulted in agglomeration of the dispersoids and sometimes leading to even total rejection. It was found that small additions of mischmetal (1-3 wt%) during dispersion resulted in better incorporation without much agglomeration of the dispersoid as evident from the macro and micro structures of the composites. Further, the additions of mischmetal increased the volume of the effective incorporation of the dispersoid even to the extent 50- 60%. The mischmetal addition results in a significant increase in the power factor of the stirrer motor indicating an apparent increase in the viscosity of the system. The higher viscosity of the melt increase the shear transmission conditions within the melt during stirring thereby breaking the agglomerates of the dispersoids. The increased viscosity of the melt seems to be due to the formation rare earth - aluminium inter metallics precipitation, as observed in the metallographic studies, thereby making the process a "pseudorheocasting? technique. A provisional patent has been filed based on this work.

Jan 1, 1989

By Tomoji Kawai

"The Pulsed Laser Deposition method using multi-targets is extremely useful for the creation of functional multi-layers and variety of artificial lattices. The topic of the present talk is on the creation of ''Function hannonized artificial lattices by laser ablation"" made of the combined magnetic, ferroelectiric and superconducting layers. The outline of talk is,1. Features of Pulsed Laser Deposition method (Laser Molecular RHEED and S1M/AFM.2. Creation of magnetic, dielectric and superconducting artificial lattices by Pulsed Laser Deposition.3. Novel properties of function harmonized artificial lattices: especially on the magnetic and magnetoresistive artificial The outline of talk is, lattices made of3d transition metal oxides."

Jan 1, 2000

By S. Vukcocic

A long term research project is in progress to establish the parameters of an acid leach process to recover alumina 'froui' high-iron and/or low-iron white bauxites, kaolinite, coal. ash and copper mine tailing. In this paper the results of acid leaching of copper flotation tailing for the removal of alumina are presented. The tailing is very complex material which contains 25% Al203 in the -10 lim fraction. X-ray diffraction indicates presence of quartz, kaolinite and minor 'alunite. After classification and ,separation of the -10 lim fraction, the raw material is fired to 550GC and leached at 90GC. Filtration is applied for the separation of white silicate residue form leach liquid. After the purification step, aluminum salt is crystallized from the solution, and calcined to alumina. Kinetic correlation and regime, of the processes are defined and presented in the paper.

Jan 1, 1992

By W. L. Cornell

The processing of lead tailings for removal of the heavy metals produces concentrates upgraded in Co and Ni values. Reflected light microscopy, scanning electron microscopy, image analysis, and Vickers hardness measurements were used to identify mineral species, associations, degree of liberation, and distributions to the test products. Siegenite and bravoite were the most common species encountered, but violarite and enriched pyrite and marcasite phases were also identified. Liberation for the Co and Ni minerals contained in the tailings was 20 micrometers or less.

Jan 1, 1993

By C. H. Quan

Solvent extraction tests were carried out on a rare earth chloride solution derived from monazite processing to determine the effect of extractant and diluent on the distribution coefficients between organic and aqueous phases, and the separation factor between rare earths. The extractants were 20% by volume di-2-ethyl-hexyl phosphoric acid (DZEHPA) or 2-ethyl-hexyl phosphonic acid (Ionquest® 801). Four Shellsol diluents were tested ranging from nil to 100% aromatic content. D2EHPA gave the highest rare earth extraction for a given pH but was less selective than Ionquest. The geometric mean separation factor between adjacent rare earths varied from 2.41-2.56 for D2EHPA to 2.62-3.01 for Ionquest. The nil-aromatic diluents (Shellsol 2037 and 2358) gave better separation factors in Ionquest but, in D2EHPA, were slightly inferior to the 100% aromatic diluent Shellsol AB. Yttrium behaved as a pseudo-heavy rare earth with a distribution coefficient lying between Ho and Er, as expected from its ionic radius.

Jan 1, 1992

By Yingtao Zhang, Shaofeng Du, Yiming Rong, Wenjun Zhao, Gang Wang

"20Cr2Ni4A steel is a kind of high quality steel mainly used for manufacturing high-duty gears in the world. The high-duty gear with good performance must have wear and fatigue resistance properties. In order to get the good properties, the high-duty gear needs a high hardness gear surface and a good hardness gradient along the depth direction. In this paper, the samples were designed and a vacuum carbonitriding process was put forward to improve the surface hardness of parts for 20Cr2Ni4A. The process contained carbonitriding, quenching, cryogenics, and tempering process. The surface hardness and hardness gradient of carbonitrided samples were measured and the good microstructure was gained. The surface hardness is 67.SHRC and the case depth is 1.2mm.IntroductionSteels are widely used in industry, but the fatigue strength and the wear resistance of steel is much low. So the heat treatment process is put forward to improve the mechanical properties of steel. It can be improved by high-energy heat treatment methods for medium-carbon and highcarbon steel. Those methods will not alter the chemistry of the base metal [ 1].For low-carbon steels, carburizing and quenching should be used to improve the steels' mechanical properties, especially the surface properties. Compared with the carburizing, carbonitriding has more advantages, such as a short production cycle, low temperature and small deformation of parts. Carbonitriding is a modified form of gas carburizing, rather than a form of nitriding. The modification consists of introducing ammonia into the gas carburizing atmosphere to add nitrogen to the carburized case as it is being produced. Nascent nitrogen forms at the work surface by the dissociation of ammonia in the furnace atmosphere; the nitrogen diffuses into the steel simultaneously with carbon. Typically, carbonitriding is carried out at a lower temperature and for a shorter time than is gas carburizing, producing a shallower case than is usual in production carburizing [2]. As a material surface strengthening technology, carbonitriding has been widely used in the production [3]. And vacuum carbonitriding process is better than carbonitriding, because the vacuum carbonitriding temperature can be higher than carbonitriding without surface oxidation."

Jan 1, 2014

By John ?gren, Martin Schwind, Henrik Larsson

"A new model for internal oxidation, as well as similar processes, has been implemented on computer. It is based upon a combination of random walk and cellular automata and is capable of treating 3-dimensional cases. To model diffusion, it utilises quantised units of matter. All steps of the process are included: nucleation, growth and coarsening. The effect of grain boundaries on diffusion as well as nucleation is taken into account. Further possible development is briefly discussed; especially the treatment of nucleation needs further consideration. IntroductionComplex diffusion-controlled processes may now be simulated on a routine basis when concentration varies along one co-ordinate only. One-dimensional simulations capture much of the information of interest but not all. For the case at hand, especially the spatial and the size distribution of precipitates, as well as the impact of grain boundaries, would be interesting information not accessible from 1-D simulationsSolving the full Fick-Onsager law in three dimensions does not seem feasible with the computers of today. In the model described in this article, random walk by quantised units of matter are considered. The model should be useful for a number of cases involving dispersed systems. With further development, it would indeed seem possible to simulate most types of phase transformations.Previous workWe have previously published two articles [1,2] on the new approach discussed in this work. In those articles we described the basic idea and showed, among other things, that very good agreement with an experimental concentration profile can be obtained, in a single-phase system, using independently assessed thermodynamic and kinetic data. Also, Schwind used the same random walk based concept to model coarsening [3]."

Jan 1, 2001

By J. P. Rodier

Despite the good years that the non-ferrous business is now enjoying, one should not forget that in this business growth rates are low, fixed assets are high and prices are more cyclical than in other businesses. Increasing environmental concern puts the industry under pressure. Lead and zinc companies are now profitable and profitability in the next ten years will depend on size of units, location, and choice between new technology and upgrading current ones. Implementation of Metaleurope was a strategic move. It produced a company of sufficient size to achieve new steps in cost cutting and yet remain flexible enough to deal with rising variety of primary and secondary raw materials.

Jan 1, 1990

By A. Bruynesteyn

It is well known that most North American gold deposits are of a hydrothermal origin and therefore they are often associated with sulphide minerals such as pyrite and arsenopyrite. When the precious metals in such ores are held captive inside sulphide crystals, the ores are called refractory because they do not respond to treatment by direct cyanidation. In these cases, it is necessary to recover the contained precious metals using high temperature treatments such as smelting or roasting, or high pressure leaching processes to break down the sulphide crystal matrices and thus liberate the precious metals for subsequent extraction by cyanidation. Sulphidic gold ores containing arsenic and/or antimony are considerably more difficult to treat because, in addition to their refractory nature, the arsenic and antimony content also prohibits treatment by direct cyanidation or amalgamation. These ores must be milled and their sulphidic gold values concentrated by flotation. The resultant concentrates must then be roasted to break down the sulphides before cyanide treatment can be applied.

Jan 1, 1985

By B. R. Baldock, R. W. Matusewicz

The recycling of used computer boards is a key industry activity for the recovery of precious metals. The safe and effective separation of metallic from non-metallic materials and subsequent processing of these secondary materials to provide high recoveries of values and excellent environmental performance are critical process requirements. Ausmelt Technology has been used commercially in four plants for the recovery of precious metals and has also been used very successfully at pilot plant scale to process computer boards. This work and its application to commercial operations with particular reference to processing conditions and environmental performance are reviewed.

Jan 1, 2000

By Raj Mutharasan

The phenomena of gas-molten metal reactions for the production of metal matrix composites consist typically of a combination of one or more gas transport steps and a liquid gas reaction step. Reaction products include such strength enhancers, grain refiners, or high thermal conductivity phases as TiC, AIN, SIC, Si3N4, TiN in aluminum alloys. Nitrides, carbides and oxides can be produced at various volume fractions and in fairly fine sizes (500 am to 5 um) in laboratory melts by Reactive Gas Injection method (RGI). Gas injection methodology to produce the reinforcements is attractive because it can potentially be scaled to production scales in excess of 10,000 kg/h. For continuous production, the reactant molten metal can be continuously fed into the .crucible where the reactive gas is injected. The molten metal phase reactant may also be involved in a controlling transport step, depending on its concentration and viscosity. It is well known that the reaction product reinforcement size and shape of these phases have significant impact on the physical, mechanical and thermal properties. The current state of knowledge is unable to predict the kinetics and growth of solid reaction products obtained. The primary goal is to develop a fundamental framework for the understanding and prediction of the particle size in such reaction systems. In addition, the role of gas transport, liquid hydrodynamics and decomposition are important issues. A reaction-transport model is being developed using a reaction, transport, and thermodynamic framework, both at macro and at atomistic level to assess gas - liquid interactions.

Jan 1, 1996

By Yinlun Huang, Cristina Piluso

"Industrial sustainability looks to improve material and energy efficiencies, product quality and variety, and productivity within an industrial zone, thus pursuing the long-term sustainable development of the region. This paper introduces a systems-based modeling methodology, which provides industrial leaders with the ability to evaluate future production options to determine the path with the highest positive impact on both their own sustainability and the sustainability of the overall industrial zone. A comprehensive study on sustainable development of an auto-manufacturing focused industrial zone under uncertainty is illustrated. Introduction Sustainable development refers to a continuous process of improvements that must be followed in order to achieve a state of sustainability. In its most general form, a widely accepted definition of sustainable development was identified in the Brundtland Report as “development that meets the needs of the present without compromising the ability of future generations to meet their own needs” [1]. Sustainability will occur when the material and social conditions can be maintained or improved for human health and the environment over time without exceeding the ecological capabilities that support them [2]. An industrial zone is defined as a geographic area comprised of a network of industrial sectors, each composed of a number of entities. Such a zone is highly integrated and complex, and contains numerous uncertainties due to each industry’s extreme dependencies on its suppliers and customers throughout the product supply chain. In the context of an industrial zone, sustainable development refers to the continuous process of advancements in the zone, and the entities that comprise it, creating more value, wealth, and profits (economically viable dimension), providing environmentally benign products with less raw material consumption and waste generation (environmentally compatible dimension), and collaboration and a direct relationship among all involved in the supply chain, i.e. the corporations, employees, suppliers, investors, communities, customers, etc. (socially responsible dimension). These are the triple bottom lines of industrial sustainability. In order for economic, environmental, and social sustainability improvements to be successfully implemented within an industrial zone, the industrial decision makers must possess system-wide analysis abilities. The analysis of the sustainable development of an industrial zone involves decisions at the local, regional, or national levels, which are complex and involves handling of ill-defined parameters with a high degree of uncertainty due to the imperfect understanding of the underlying issues [3]. This work focuses strictly on the uncertainties in future zone planning and a method and a scenario based approach that can be used to evaluate the sustainable development of an industrial zone among these uncertainties."

Jan 1, 2008

By Mingchun Lu, Zhijia Liu, Xueqi Zhang, Jianliang Zhang

"In order to solve the problem of shortage of scrap, especially high quality scrap, a new substitute for scrap or DRI has been developed. The decarbonization mechanism of granular pig iron has been analyzed and the technical process and decarbonized granular pig iron have been evaluated in this paper. The research result shows that this new process is superior to direct reduction process in product quality, construction investment, operation flexibility, production efficiency etc. Decarbonized granular pig iron (DGPI) not only can be used as conventional scrap but also can be charged into EAF as high purity .burden equivalent to heavy scrap:IntroductionIn the past years, with the universal application of continuos casting technique in China, the amount of scrap generated inside steelworks has been reducing continually. On the other hand, the EAF steel proportion is increasing and this gives to the obvious change in structure of steel product. At present, the requirement on both scrap quantity and scrap quality is being paid more and more attention. Because China is a country which is devoid of scrap and poor in resource (nature gas and high grade iron ore) for developing direct reduction iron (DRI) so that sponge iron can not be produced cosmically in China and has to be mainly imported. Instead of part of scrap, some cold pig iron in cold state has been charged into EAF in China. However the high carbon content in pig iron has limited its proportion in EAF metal burden. Because the price of pig iron is lower than that of imported DRI in China, the technique of granular pig iron decarboniztion is hopeful to become effective way to produce substitute for scrap or DRI."

Jan 1, 2000

By A. Mejias, M. A. Garcia, G. Diaz

During 1997 and 1998 two successful zinc feasibility studies, Skorpion and Sanyati, were carried out by Tecnicas Reunidas based on the modified ZINCEX® technology. The technical viability of each project was proved during more than 600 h of continuous running in a pilot plant. The Skorpion zinc project would recover 150,000 t SHG Zn/y from an oxidized zinc ore of a Namibian mine. The economical study showed that the plant would have the lowest production costs in the world. The Sanyati zinc project would treat a bleed from an existing copper refinery in Zimbabwe to recover 5,000 t SHG Zn/y. In the first case the electrowinning cellhouse was supplied by Union Miniere and in the second by Tecnicas Reunidas. This article highlights the pilot plant results and the advantages of the proposed process over conventional zinc production practices.

Jan 1, 2000

By Keri Ledford, Stephanie Lin, Jason Nadler

Novel processes are being developed to fabricate thin copper thermal wick samples of a targeted porous microstructure. Structures of desired porosity, thisckness and pore size and distribution are achieved by tayloring the incorporation of sacrificial polymer beads in to slurry precursors. The thickness of the final structure is dictated by precisely controllable slurry application methods, such as spin coating. Ina subsequent heat treatment, th epolymer components thermally decompose and the remaining copper particles sinter to form a reticulated foam. The resulting microstructures are characterized in terms of porosity, permeability and specific surface area.

Jan 1, 2012

By R. M. Luna-Sánchez

Electrochemical studies, particularly Evans? diagrams, have been employed in hydrometallurgy to simulate and explain the redox phenomena that take place at mineral and metal surfaces during operations such as leaching and cementation. However, despite their utility, in some cases, the combination of the cathodic and anodic branches, determined separately, does not reproduce the chemical environment present when both processes occur simultaneously on a specific surface. In the present paper, limitations of Evans? diagrams are analyzed through two examples: silver sulfide cyanidation and gold cementation on zinc. In both cases, the surface kinetics are sensitive to the local pH and cyanide levels. When the electrochemical oxidation of silver sulfide or the reduction of gold are performed in the absence of its corresponding redox reaction, the local pH obtained does not simulate the real situation and the combined reaction kinetics may be very different from those determined from the Evans? diagrams.

Jan 1, 2003

By P. Chris Pistorius

"Use of coke in blast furnace ironmaking is the main origin of carbon dioxide emissions from integrated steelmaking. Use of pre-reduced iron feedstocks would reduce the coke rate and, if pre-reduction were carried out with natural gas, would decrease the overall carbon intensity of ironmaking. Blast furnace productivity would also increase, because the blast volume per unit of hot metal would decrease. This paper shows that these trends can be predicted quantitatively, by using a conceptually simple Rist-style blast furnace mass and energy balance, assuming furnace productivity to be limited by the tuyere gas flow rate. Such predictions would assist in optimizing the choice of the degree of reduction and relative amount of pre-reduced blast furnace feed.IntroductionSteelmaking is responsible for some 5% of world CO2 emissions, at a rate of approximately 1.9 tonnes of CO2 per tonne of cast steel [1]. In integrated steelmaking, the ultimate source of most of the CO2 emissions is coke, the indispensible (and expensive) fuel and reductant for blast furnaces. There are several research programs underway worldwide which seek to lower the carbon intensity of ironmaking; one of the largest is the European ULCOS program [2], in which the main proposed change to blast furnace ironmaking is to scrub CO2 from the furnace off-gas (for possible sequestration), recycling the remaining gas to the furnace. To limit the recycling nitrogen load, oxygen rather than air is used to combust coke.A conceptually simpler approach is to charge prereduced feed (direct-reduced iron) to the blast furnace. This approach has been used for some two decades at the AK Steel Middletown plant, where some 200 kg of direct-reduced iron (DRI) is charged per tonne of hot metal [3]. The Middletown blast furnace has exceptionally high productivity (rate of iron production relative to the furnace hearth area), simply because less coke is required per ton of hot metal if part of the feed is already metallic. Midrex [4] has provided some quantitative predictions of the implications of DRI use in the blast furnace, stating that for every 10% of Fe in the feedstock that is in metallic form, the fuel requirement decreases by 7% and the productivity increases by 8%."

Jan 1, 2012