Search Documents

By M. A. Rodrigues da Silva Enríquez

One of the rare consensual points among different resource-based economic analytical approaches refers to the strategic role of rent from mineral extraction, as a decisive tool to ensure that the temporary wealth generated in the present can turn into permanent income in the future. For this reason, evaluation, distribution and use of mining rent plays a central role in the sustainable development of mining cities. Brazilian legislation provides for this at the municipal level by means of participation in the financial results of mineral extraction accomplished in these municipalities, with the Financial Compensation for Mineral Exploration (CFEM). CFEM is a type of ad valorem royalty, which charges taxes of up to 3% of the net revenue of mineral production. However, legislation does not establish how these resources should be used. Therefore, there is wide variation in the use of CFEM income among Brazilian mining cities. A study from a sample of the 15 largest mining cities in eight Brazilian states made possible identification of two main patterns with regards to the use of CFEM which were labeled "sustained use" and " the pitfall of the single treasury." In that regard, this article discusses the pressuring factors that contribute to these patterns, as well as the institutional arrangements which may be more favorable to inducing more sustained use of CFEM.

Jan 1, 2011

By J. Potter, A. Anani, C. Antonio

This research aims to test the hypothesis that the low retention rate of women in the mining industry is caused by workplace culture and policies established due to gender segregation. A quasi-experiment is developed to determine the cause-and-effect relationship between gender segregation-inspired culture and the retention of women. The experiment considers the impact of the job type and the operational environment. The analysis provides information on factors that cause low retention of women in the industry, the extent to which gender segregation plays a role, and insights that allow actionable and measurable changes in the industry.

Feb 1, 2023

By Jeff Salai

The CP-3A contract is the final segment of the MWWST’s 28.3 km (17.6 mile)pressurized water supply tunnel for the metropolitan Boston area. The 1,288 m (4,226 feet) of U-shaped tunnel alignment passed through five rock zones employing four different primary support systems. The short tunnel began in Weston, Massachusetts, at Shaft 5A in soft, completely weathered argillite, passed through a fault zone, and ended in Dedham granite. An 18-foot diameter horseshoe starter tunnel was built to accommodate a 4.94 m (16-foot 2 1 / 2 inch) diameter Robbins TBM. Heavy water inflows were anticipated and subsequently encountered during probe drilling. Pre-excavation grouting was implemented at high pressures to displace high water inflows in the starter tunnel and consolidate the fault zone. This paper will provide an overview of the tunnel construction with an emphasis on ground control, grouting and survey control.

Jan 1, 2001

By L. K. Holder

The White King / Lucky Lass Superfund site consists of two former uranium mines in south-central Oregon. The remedy included consolidating two large mining overburden stockpiles that contained low levels of radioactivity and heavy metals by moving over 700,000 cubic yards of material and then capping the combined stockpile. An innovative armored cap design was used to minimize the stockpile footprint and thereby prevent disturbing existing wetlands. In addition, the stockpile was designed to merge into the surrounding topography. The remedy also included stream restoration and development of new wetlands. The stream was returned to its pre-mining channel, with the addition of hydraulic features to create new wetlands. The wetlands have greatly enhanced the ecological value of the remedy and the site.

Feb 23, 2014

By Donald S. Bubar

The Separation Rapids property, located approximately 60 km (37 miles) north of Kenora, Ontario, Canada, is host to one of the largest rare metal pegmatite deposits in the world. This pegmatite was named the Big Whopper by its discoverer, Dr. Fred Breaks of the Ontario Geological Survey, because of the exceptional length and width of the surface exposure. The property is readily accessible from a main, all-weather road via a network of secondary logging roads. The main line of the Canadian National Railway passes through the village of Redditt, just 40 km (24 miles) south of the property. The Big Whopper is one of the complex-type (petalite sub-type) class of rare metal pegmatites that are geochemically the most highly evolved in the spectrum of granitic pegmatites. Such deposits are economically important as resources for the rare metals lithium, tantalum, cesium, and rubidium. While complex-type pegmatites are found in many areas of the world, most are too small to be profitably mined, however, with an inferred resource in excess of 15 million metric tons (mt) (17 million short tons [st]), the Big Whopper is only the fourth deposit of its type in the world with the size required to be of major economic importance. The other three deposits, which are currently in production, are the Tanco mine in Manitoba, the Bikita mine in Zimbabwe, and the Greenbushes mine in Western Australia. The Big Whopper is situated in the eastern continuation of the Archean Bird River greenstone belt which also hosts the Tanco pegmatite, approximately 60 km (37 miles) to the west. The principal commodities identified in the portions of the Big Whopper pegmatite explored to date are petalite (LiAlSi4010) and rubidium-rich K-feldspar. These are industrial minerals with important applications in the glass and ceramics industries. The Big Whopper also contains substantial quantities of lepidolite, a lithium, rubidium-mica which is the principal ore mineral for rubidium metal. Tantalum and cesium occur in anomalous levels with the petalite mineralization, and the possibility of finding zones of high enrichment in these valuable high-tech metals elsewhere in the deposit is excellent. Such enriched zones are typical of pegmatites as highly evolved as the Big Whopper. To date, the geological mapping and diamond drilling work completed by Avalon have delineated the Big Whopper pegmatite system over a strike length exceeding 1.5 km (0.9 miles), over widths ranging from 10 m to 80 m (30 feet to 260 feet) in thickness, and to a vertical depth of close to 300 m (1,000 feet), where it remains open. The pegmatite system consists of a vertically oriented massive petalite pegmatite dyke striking 280 degrees that is flanked by amphibolites containing a swarm of narrower albite and petalite dykes which have all undergone intense deformation in a high strain zone resulting in folding and intense shearing. The Big Whopper exhibits a mineralogical zonation pattern which is complicated by the superimposed deformation that has both folded and stretched the deposit. Drilling has defined a dilute geological resource totaling 7.1 million mt (7.8 million st) grading 1.283 percent Li20, 0.346 percent Rb20, and .007 percent Ta205 over a strike length of 600 m (2,000 feet), and to a vertical depth of 250 m (820 feet), where it remains open. The petalite and rubidium-rich-K-feldspars contained in the Big Whopper all appear to be of superior quality. The grades are consistent with a petalite content averaging 25-30 percent and a rubidium-rich-K feldspar content averaging 15-20 percent. The remainder of the rock consists mainly of albite, several types of mica, and quartz. Accessory minerals include columbitetantalite, cassiterite, apatite, garnet, and gahnite. Market studies show that the deposit is located close enough to existing transportation infrastructure to access rapidly growing, major markets in the glass and ceramics industries, both in the northeastern U.S. and Europe. There are only three competing lithium minerals producers in the world with the Bikita mine in Zimbabwe being the only major producer of petalite. The other lithium deposits produce spodumene, a less desirable lithium mineral. Lakefield Research Limited has successfully designed a process to produce an ultra-pure petalite concentrate containing up to 4.65 percent lithium oxide, and as little as 0.014 percent iron oxide, low levels of soda and potash, and negligible amounts of other trace elements. With these specifications, Avalon will have an excellent quality product for glass-ceramics applications such as Corningware®, CERAN® stove tops, and other thermal shock-resistant products. Lakefield is presently designing the balance of the flowsheet to produce separate concentrates of rubidium-rich K-feldspar, albite, mica, tantalum, tin, and high-purity quartz. Initial test work indicates that the feldspar products will be of exceptional quality. The K-feldspar concentrates contain 11-12 percent K20 and 1 percent Rb20, while the sodaspar contains over 10 percent Na20, and both have very low iron (0.01 percent Fe203). A preliminary economic model shows that with an initial production rate of 90,000 mt (100,000 st) per year, expanding to 170,000 mt (190,000 st) per year over 5 years, the project is capable of generating over CDN $10 million per year in pre-tax cash flow by year 5 on a capital cost of approximately CDN $30 million.

Jan 1, 2001

By Miroslaw M. Hajdasinski

A project's rate of return (ROR) [The list of all the acronyms used in his text is provided at its end.], be it an internal or external one, usually needs to be approximated. The success and efficiency of an approximation procedure depend on the quality of the initiating parameters such as bounds or seed values (guesses). Current approximation procedures commonly use bounds and guesses dictated by intuition rather then by mathematical consideration. The paper presents three ROR-bounding and six ROR-guessing approaches and examines their suitability on the examples of the typical project cash flow patterns.

Jan 1, 1996

By W. Jack Wilkes, Gilbert L. Butler

TRANSPORTATION TUNNELING The use of tunnels for transportation, namely rapid rail transit systems and highways is on the increase. How much that increase might be through the 1980's is the question that is discussed in this paper. In 1975, there were 218 route miles of subway tunnels for rapid rail transit and 154 lane-miles of highway tunnel. From the viewpoint of many transportation planners and designers, the tunnel is one of the tools which may be used to by-pass many types of obstacles: a mountain, a body of water, or a Central Business District (CBD). Therefore, the transportation tunnel is a rural as well as an urban solution with major emphasis on the latter because of the current transportation needs of our cities. In the case of rural locations, tunnels are usually constructed through mountains in order to eliminate miles of steep grades and dangerous curves, such as the Eisenhower Tunnel which cuts through the Continental Divide in Colorado along 1-70 and saves 10 miles and 40 minutes of driving time. Tunnels also provide an excellent transportation link across bodies of water in order not to interfere with shipping lanes. The Chesapeake Bay Tunnel and Bay Tubes of the BART system are excellent examples of this type of tunnel.

Jan 1, 1976

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By Elisabeth Tønnesen, Lloyd Tunbridge

"SUMMARY Injection grouting in rock around tunnels is used to reduce or stop water inflow. Little is known about the distribution of pressure within the rock mass during and after grouting. Instrumentation was developed to record pressure at the back of the packers inside the rock mass during injection grouting in order to improve our understanding of the process. Using this equipment measurements inside multiple injection holes during injection pumping have been made during several rounds of injection grouting in a tunnel. The data has been compared to the data recorded on the grout pumping rig and analysed to gain an understanding of the behaviour of grout injection process in the rock mass. The initial results are reported in this paper. INTRODUCTION Construction of a tunnel in soil or rock below the ground water table frequently results in the flow of ground water into the tunnel if the ground is permeable or fractures conductive. The injection of cement or chemical based grouts is frequently used during tunnel construction to reduce flow of water into a tunnel. Significant water flow into a tunnel is undesirable for several reasons: • there is a high cost in pumping out water over the lifetime of a tunnel; • drips and flows of water have to be diverted from the roadway or track; • where freezing conditions occur there is the possibility of ice build up and; • ground water levels may be changed possibly affecting surface water such as causing drainage of lakes and ponds, and changes in vegetation. Grout injection is most effectively done ahead of excavation to ensure that the grout penetrates the ground. Where heavy flows of water already occur into a tunnel the grout may be washed out before it sets. Normal practice in ground where water flows are encountered is to inject grout in a number of long holes ahead of the face with outer holes forming a ring around the proposed tunnel excavation – eventually forming a shield of grouted rock around the final tunnel, Figure 1. The holes may be sealed off a couple of metres into the rock with an expandable rubber plug around a pipe through which the grout can be injected, Figure 2. A one-way valve in the plug stops the grout from flowing back out of the hole when pumping stops and avoids grout flowing out through neighbouring holes. The rubber packer with a one-way valve permanently installed in the injection hole precludes the measurement of pressure down the hole when pumping is stopped."

Jan 1, 2016

By Sharon Thomson

Since 1977, Amax Coal Co.'s Belle Ayr mine near Gillette, WY, has been the largest producing coal mine in the US. In its 10 years of operation more than 90 Mt (100 million st) of coal have been shipped from the mine's facilities to electric generating plants across the country. It is thought to be the largest amount ever produced in US history from a single coal mine. The railroad is Belle Ayr's lifeline for moving this massive volume from a relatively isolated corner of northeastern Wyoming. There are no waterways for barge traffic, and highway truck hauling would be impractical considering the quantity and distance of coal to be moved. Transportation in the Powder River Basin-at least for the present-is strictly unit trains. An average of four unit trains daily load at Belle Ayr. These trains average 108 cars long, with a capacity of 91 t (100 st) per car. Burlington Northern Railroad serves the Powder River Basin, but locomotives supplied by Union Pacific, Milwaukee Road, and Kansas City Southern are a common site as well, since coal will often travel these lines too on its way to utility plants in Colorado, Kansas, Iowa, Texas, Arkansas, Louisiana, Wisconsin, and Oregon. When Belle Ayr opened transportation in the Powder River Basin was in an early development stage. As the first large-scale coal shipper in the area, Belle Ayr was the only user of a 27-km (17-mile) railroad spur south of Gillette. Other mines, however, were to open soon on the abundant, low-sulfur reserves. Today, less than a decade after Belle Ayr's debut, 13 large-capacity mines operate near Gillette. The 27-km (17-mile) spur that once served only Belle Ayr has been extended 177 km (110 miles) south to service other mines as well, and to tie into a major rail line in central Wyoming. The Powder River Basin is now served by a wishbone-shaped track configuration that allows train movement north into Montana, south into Colorado, and east into Nebraska for connections across the country. Operations at Belle Ayr are closely tied to train arrivals and departures, with coordination essential between mine operations and rail personnel. "Train movement in the Powder River Basin has evolved to the point where we are fine-tuning mining operations to coordinate them with a more dependable transportation system," according to Joe Jefferson, transportation supervisor with Amax Coal's western division. That, however, hasn't always

Jan 10, 1982

By R. Wild

[When a blast furnace has a certain defined burden and is operated under fixed conditions of blast temperature, etc., the fuel efficiency is determined by the extent to which the reducing gases can remove oxygen from the burden in the furnace stack. This is determined by two distinct factors: 1) The uniformity of gas-solid contact, and 2) The ease with which oxygen can be removed from individual pieces of burden. This latter is often called burden reducibility. When burdens were poorly prepared the first factor was by far the most important and a study of the reducibility of individual lumps was of rather academic interest recent years good burden preparation with emphasis on sized material has led to greatly improved gas distribution in the stack, and thus the second factor has become much more important and there has been a marked increase in interest in methods of measuring reducibility.]

Jan 1, 1964

By Eugene R. Palowitch, Albert W. Deurbrouck, Thomas H. Parrsons

INTRODUCTION Hydraulic concentrators utilize the physical characteristics-size, shape, and specific gravity-of particles suspended in a fluid medium to effect a concentration of desired quality. Fine-coal concentrators include generally those devices which are used to clean roughly 3/4, in. (9.5 mm) top-size coals. While this size designation is somewhat arbitrary, it is consistent with current practice although some fine- coal concentrators can treat coarser coals effectively. A variety of devices have been and are currently being used to wash fine coals and include: dense media cyclones, wet concentrating tables, hydrocyclones, jigs, spirals, launders, and upward-current classifiers. As launders and upward-current classifiers have been replaced by more efficient devices, they no longer warrant consideration as fine-coal washers. And as fine-coal jigs were addressed with the Baum jig under Part 1, Section 2, and heavy media cyclones and hydrocyclones were addressed under Part 2, Section 1, of this Chapter, only the wet concentrating table and the spiral concentrator will be discussed here. WET CONCENTRATING TABLES History The current wet concentrating table evolved from continuous belt concentrators which utilized a flowing film of water to recover heavy metals. In these devices the heavier concentrate moved up the inclined plane of the belt while the lighter impurities were washed away by water flowing down the belt. The natural outgrowth of the continuous belt concentrator was the vanner, a vibrating endless belt which was first developed about 1860 by Hartwig. Later models of the vanner, such as the Frue, incorporated oscillation in a plane transverse to the direction of the water current. Excellent descriptions of these washers are found in The Cleaning of Coal, by Chapman and Mott.80 Further development of tables included the circular stationary table (Linkenbach), the multiple round table (Anaconda-Evans), the bumping table (Campbell), and finally the differential-motion table which is now used extensively for cleaning fine coals.

Jan 1, 1991

By Manuel Bernales, Aldo Leon, Alexandra Carlier, Bern Klein, Andre Xavier

Mining companies and governments at both the local and national levels recognize that Participatory Environmental Monitoring and Surveillance Committees (PEMSC) are necessary mechanisms for meaningful engagement at the community level. In many cases, PEMSCs are established as volunteer initiatives by mining companies or by the mining communities themselves. In Peru however, they can also be recommended by the government as way to address social conflict. Most PEMSCs are launched while a mine is in operation and have the objective of monitoring both water quality and quantity. Many established committees are currently evolving and adopting a more comprehensive approach, as well as expanding their initial scope from a river or micro-basin focus and watchdog agenda, to a broader regional integrated resources management view. This paper examines the origins of Participatory Environmental Monitoring and Surveillance Committees in Peru. It also discusses the typology of these committees, and the scope of their work. Furthermore, it looks at the challenges faced by these committees, as well as existing opportunities for mining companies, governments, and civil society. Finally, this study presents a governance model that could contribute to the long-term existence of these committees. This discussion is further informed by the results of a national workshop that took place in October 2016 in Peru, in which over 200 representatives from 22 monitoring committees, government and mining companies participated.

Jan 1, 2017

By G. Bryant, P. Ziemkiewicz

Acid mine drainage (AMD) from both abandoned surface and underground mines is a serious problem. The flow of water and changes in quality over time from abandoned mines is important in determining remediation strategies. Acid mine drainage from surface mines is estimated to last for 10-20 years, while estimates of acid drainage from underground mines vary from 10- 100s of years. Fifteen underground mine discharges in West Virginia were studied to compare water quality changes between 1968 and 1999 to see if our data are consistent with other studies. Each of the discharges were categorized into one of three groups: undisturbed since 1968, affected by surface mining since 1968, and reclaimed. Comparing water quality between 1968 and 1999, the discharges in the undisturbed category showed a 35 to 95% improvement in acid concentration and a 40 to 99% reduction in iron concentration. The discharges affected by surface mining showed the most dramatic improvement. For acidity, iron, and aluminum, the percent improvements were all above 44%, and in most cases in the 70 to 99% range. In the reclaimed category, one of the four discharges declined in water quality. Discharge 82 showed a 76% increase in acidity, and iron and aluminum concentrations worsened by 58 and 96%. However, discharges 15 and 74 improved in water quality with a 94% acid load improvement and a 95% iron load improvement at both sites.

Jan 1, 2000

By Daniel R. Stewart, Ralph R. Sacrison

The function of the geological engineer is to assist in mine planning and operations by collecting, interpreting, and applying geologic data to the solution of engineering problems. The geologist supports this effort by collecting additional geologic information specifically useful to the engineer. This use of geologic information reinforces the value of mine geology to the mining process beyond the traditional role of orebody definition. Work discussed includes: evaluation of caving strategies at the Climax and Henderson mines, support definition and slope stability at the Climax mine, and some uses of geology in cavability estimation for the Mount Emmons project.

Jan 1, 1992

By Bradford F. Townsend, Robin B. Dill, Richard M. Croswell

Innovative geotechnical construction techniques were used to construct three pedestrian tunnels under a building slab-on-grade to allow utilization of basement space for manufacturing. Tunnels were constructed using mining techniques through granular fill soils less than three feet below on-going sensitive manufacturing operations. Project design consisted of jet grout underpinning of exterior foundation walls and an arch of drilled-in grouted horizontal dowels for soil pre-support to limit ground movements during excavation. Permanent tunnel lining consisted of arched steel rib sets and invert struts supported on precast footings encased in cast-in-place concrete slab and side walls and a gunite arch.

Jan 1, 1993

By Joe Keane

DOUG HALBE: The kickoff speaker, and my unanimous choice, is Joe Keane. Joe was born in Butte, Montana, and began his association with the mining industry as an under- ground miner at age 16. Currently he is president of KD Engineering and Metcon Research. He had it lucky when he went to school because there were only 44 elements in the periodic table, I understand. [laughter] Here's Joe. JOE KEANE: I'm doing this under protest. Maybe we can start the slides. Mr. Halbe gave me this topic, but I don't like it. I don't like Mr. Halbe either [laughter] because of the way he shanghaied me into this. He called me up on the phone and said this is what you're going to speak about: "Five Things I Never Want to See Again in Plant Design," and I said, "Huh!" Then I started getting stuff from SME about how to make a presentation. I have decided to change the title to "More Than Five Things I Never Want to See in Plant Design," since you can't have a completely negative speech; you have to have other topics. So we will have some other, not completely nonrelated, topics to sort of break the tension. I tried to find a joke to open with. I talked to Omar Mutati. All of his jokes were either about Bill Clinton, our beloved President, or they were too filthy to say in a mixed group. [laughter] So I decided to start this out with a profound statement. The pro- found statement is, "The meek shall inherit the earth, but not the mineral rights," [laughter] by J. Paul Getty. J. Paul Getty was one of my favorite guys because when a real obnoxious reporter asked him one day, "How can I become wealthy?" he said, "Drill for oil and find it."

Jan 1, 1998

By C. J. Lewis

Considerable amounts of the world's known reserves of elemental sulfur are found near the surface in areas of volcanic activity both active and inactive. Because such deposits cannot in general-be mined by the well-known Frasch process, and because other methods of recovery have not proven to be economically competitive except in isolated instances, at present these reserves remain relatively undeveloped. However, projections of world sulfur demand indicate that new sources of marketable sulfur will be needed in future years 2/, 19/. For this reason, recovery of elemental sulfur from these near-surface deposits is of continuing interest. Solvent extraction as an approach to recovery of elemental sulfur from open pit-mined ores of these non-Frasch deposits has received considerable attention particularly at the research and development level 3 /, 7/, l l /, 16/, 21/,23/, 29/ This method has been and continues to be attractive because it presents the potential of high sulfur recovery and purity of product coupled with a relatively simple process flowsheet in which low energy requirements and reasonable operating costs are thought to be possible. However, the physical and chemical characteristics of the native-sulfur ores, of elemental sulfur, and of the known solvents, have presented difficulties in the development of solvent extraction processes. Up to the present time, viable processes have not been realized within the framework of sulfur marketing conditions.

Jan 1, 1970

By Byron C. Hardinge, E. R. Palowitch, Albert W. Deurbrouck, David J. Akers, Edward R. Torak

During 1983, 42.2% of the 686.0 (624.3 Mt) million tons of coal reported, 289.6 (263.5 Mt) million tons were mechanically cleaned, of which 107 (97.4 Mt) million tons were cleaned by dense media (magnetite and sand) processes.' The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes increased from 7 to 38% between 1938 and 1983. The Electric Power Research Institute estimates that 150 million tons (137 Mt) of coal were cleaned by heavy-media processes in 1986, and that this number may increase to 265 million tons (241 Mt) by 1990.2 Dense medium separations include those coal preparation processes that clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes generally offer the following advantages over other coal cleaning processes: • Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of raw coal whose specific gravity is near the specific gravity of separation. • Ability to maintain a separating gravity that can be controlled within + 0.005 sp gr units. • Ability to handle a wide range of coal sizes. • Ability to change specific gravity of separation to meet varying market requirements. • Ability to handle fluctuations in feed, in terms of both quantity and quality. Unfortunately, dense medium processes can have the following disadvantages: • Relatively high capital costs caused primarily by the need for equipment to collect and recycle the medium. Relatively high operating costs caused primarily by operation of medium recycle equipment and loss of medium.

Jan 1, 1991