Search Documents

By J. L. Post

A large body of readily available Na-montmorillonite is present about 24km (15 miles) east of Fallon, Nevada. The clay is comparable to Wyoming Na-bentonite, but with somewhat less MgO and somewhat more Fe2O3 in its crystal structure. The physical and industrial properties of the Nevada clay are comparable to those of the Wyoming clay. The Na-montmorillonite is presently mined for use as hazardous waste barrier material and as a sealant for canals. It may be economically feasible to process the clay material for removal of impurities.

Jan 1, 1996

By M. J. Ross, D. A. Norrgran, J. A. Wernham, J. N. Orlich

INTRODUCTION Laboratory testing for magnetic concentration circuit design is a requirement, just as it is for most other types of concentration. Natural variations in raw materials allow on1 y the broadest of generalities to be made regarding magnetic separation. Further, magnetic fields are geometry dependent, leaving fundamental models of a separator overly dependent upon the exact conditions for which the models were derived. Despite this, an understanding of the basics of magnetic separation and of the problem to be attacked can result in rapid progress towards the final circuit design with a relatively simple testing program. Magnetic Separation Basic Principles A magnetic field can readily be understood in terms of lines of flux. A familiar demonstration of these lines of flux is the pattern of iron filings on a sheet of paper when a magnet is placed underneath. Lines of flux2 are measured in Gauss (1 line/cm2) or Tesla (10000 gauss). Regions of high field strength have a greater number of lines. Field direction is indicated by a convergence of lines. When a particle is placed in a magnetic field it cuts the lines of flux and alters them in one of three basic patterns. These patterns are referred to as diamagnetic, paramagnetic and ferromagnetic. Diamagnetic materials have electronic structures which react to oppose an applied magnetic field. This opposition acts to locally reduce the applied field slightly. The visualization is that lines of flux diverge and go around the particle. Because of this divergence or opposition, a diamagnetic particle will tend to move towards regions of lower flux density. That is to say that the particle will be repelled by a magnetic field. Aluminum oxide and napthalene are examples of diamagnetic materials. Paramagnetic materials have an electronic structure which increases an applied magnetic field. Although these materials also exhibit diamagnetism, they have randomly oriented impaired electrons which align with the magnetic field. The resultant local field enhancement is significantly larger than the diamagnetic opposition. The visual-

Jan 1, 1986

By Carl (Original by) Hrovatic

Land is a precious resource and should be treated as such by all members of our society. The soil covering this earth is only a very thin outer layer, varying in thickness from a few inches to a few feet and covering the rocks and minerals lying beneath the surface. The wise use of this valuable commodity is the responsibility of everyone. Many everyday activities disturb e earth's surface. Examples are highway construction, housing and commercial developments, agriculture, and various types of mining. This chapter discusses the relationships of the environment to land as it applies to surface operations in the coal industry. Mining by surface methods disturbs, for a brief period of time, thousands of acres of land annually. In addition, refuse piles, slurry ponds, abandoned mine structures, unprotected mine openings, and unsightly cleaning plants can also adversely affect land unless properly handled.

Jan 1, 1981

By Christopher R. Winter

Mining companies have sharpened their refocus on their tailings management strategies in recent years. Mining companies with tailings storage facilities that use the upstream construction method have been challenged to track the evolution of industry standards, assess risks, revise design, and communicate design revisions with regulators. While many aspects of best practices and industry standards have evolved in recent years as an attribute of continual improvement, the controlling standard in the design of many upstream dams is understanding the foundational strengths of hydraulically deposited tailings. Following best practices and industry standards, Hibbing Taconite Company managed by Cleveland-Cliffs, began the re-evaluation of foundation strengths underlying a system of upstream dams at the company’s iron ore mine tailings storage facility in northern Minnesota. Initial steps in the re-evaluation require reanalysis of design parameters and recommendations by the Engineer of Record to the Owner, which was followed by a series of meetings with the Technical Review Board to determine an initial path forward. Once a path forward and preliminary design parameters were determined, the Owner engaged with the State Dam Safety Engineer to discuss and seek approval of the plan. With continuous regulatory engagement throughout the process, further refinement of the design parameters for the hydraulically-placed tailings foundations underlying upstream dams began with field and lab geotechnical investigations. Following a review of risk assessments and trigger actions response plans, Hibbing Taconite revised its tailings storage facility operating plans and budget for the coming years. Based on the findings of the re-evaluation, reanalysis, and refinement of parameters, a paradigm shift was realized with the hydraulically placed tailings foundation strengths underlying the upstream system of dams. This paper explores the path that the Hibbing Taconite Company followed to understand the paradigm shift and construct downstream improvements. The plan involved tailings re-characterization, dam design revisions, operating plan reconciliation, budget revisions, wetland permitting, dam safety permit amendments, storm water prevention plans, borrow materials studies, new concrete decant structures and the pursuit to recognize and be consistent with industry standards.

Feb 1, 2024

By E. L. Reed

This paper addresses the state and federal permit- ting requirements and regulatory constraints associated with the development of new "grass roots" surface coal mines in the Western United States. Since a major portion of new coal development in the West will be on federally leased coal in Wyoming, my comments are directed towards that geographical area. This will give the reader some insight into the current regulatory framework within which western mining companies must operate-i.e., the major applicable state and federal laws and regulations, the more important state and federal regulatory agencies, and the major construction and operating permits that are required. Before discussing the impact of the regulations on our business, I would like to tell you something of my company and then briefly discuss Exxon's forecast of the long range outlook for coal. Carter Mining is an Won affiliated surface coal mining company. Exxon became interested in the coal business in the mid 1960's with the recognition of the future need for alternative fuel sources. Since that time, it has acquired coal reserves located in Wyoming, Montana, North Dakota, Arkansas, Texas, Illinois and West Virginia. Carter's first surface mine, the Rawhide Mine, located north of Gillette, Wyoming began production in August, 1977. Our second surface mine, Caballo, located just south of Gillette, began operating last October. We have a third block of federally leased coal just east of Gillette. By 1985 we anticipate Carter's western surface mines will be producing at an annual rate of 30 million tons, subject, of course, to successful market development efforts and regulatory considerations. Rawhide will ultimately have a permitted capacity of 24 MM tons per year. The coal at Rawhide is in two seams; one 80 feet in thickness and the other 20 feet (including a 6 to 10 foot parting). A large shovel is used to remove the overburden, and a similar shovel and dragline are used to mine the coal. Caballo has a 75 foot seam; otherwise it is similar in design and operation to the Rawhide Mine.

Jan 1, 1979

By RALPH BALTES, AMIR EHSAN KIANFAR, FABIAN UTH, ELISABETH CLAUSEN

As indoor positioning provides particular challenges due to the unavailability of GPS signals, various systems such as ultrawideband (UWB), radio frequency identification (RFID), ultrasound, and wireless local area network (WLAN) have been proposed in recent years. Some of these technologies are currently being marketed and some are still being developed. UWB technology allows for higher precision while also reducing power consumption. Hence, the underground automation and localization systems can use this technology for more accuracy and robustness. This article discusses new robust UWB modules used for underground positioning and collision avoidance with regard to human safety in underground mining operations.

Jul 31, 2020

By Robert G. Lundquist

REAM (for Rapid Excavation And Mining) is a method of rock fragmentation by high-velocity projectile impact developed by Physics International Company. This paper reports the results of field testing over the last two years. The success of the method is based on the fact that the amount of rock broken per shot scales nonlinearly with projectile impact energy. Thus, high energy impact yields spectacularly low specific energies for rock breakage. The field work reported used 90- and 105-mm military guns to accelerate 8-1/2 and 10-pound concrete and steel projectiles to velocities of 5000 to 5500 fps. All tests were performed in a competent 25,000 psi granodiorite at Hope Valley, California. During the first year of field testing 26 feet of 13-foot-diameter tunnel were produced with the 105-mm gun. The first 20 feet of this tunnel were line-drilled to aid in producing a stable portal. During the second year the tunnel was extended an additional 29 feet using the 90-mm gun. The 55-foot tunnel was produced by 590 shots. Between 1-1/4 and 1-1/2 tons of granite were broken by each shot. A silenced 90-mm gun was placed underground and the tunnel portal closed with a steel barrier. Overpressures of less than 1 psi were measured on the inside of the barrier, corresponding to an impulse noise of about 170 db. The muck produced was similar to drill and blast muck. Overbreak and ground support problems appeared to be less than with drill and blast. The contour of the tunnel was easily controlled using the 90-mm gun; the tests were also conducted using a 57-mm gun for trimming. Projections indicate that advance rates with REAM will be three to seven times faster than drill and blast, at less than two-thirds the cost. This is based on the development of a fully integrated continuous system and an inexpensive propellant giving a total expendables cost of less than $3 per shot. Other applications of the REAM technology are found in secondary breakage for open pit mining, in drilling large diameter holes, and in underground mining for longwall mining, overhand stoping, and raising.

Jan 1, 1974

By Jerry L. Fuller

Fan performance graphs are generated by digital computer using two programs, RUN- FANS and FANPLOT. RUNFANS calculates fan performance data from stored specific-volume, specific-speed data for a given fan type with appropriate allowances for fan diameter, rotational speed and air density. FANPLOT accepts specifications for drawing the graph and accepts either user-supplied pressure-quantity data or RUNFANS- calculated data as input, Operational procedures for both programs are detailed and examples of their interactive query routines are included. The hardware necessary to generate the graphs is illustrated. Several hardcopy output options are discussed,

Jan 1, 1984

By I. E. Perera

Experiments were conducted to evaluate the response characteristics of commercially available gas, smoke, and flame sensors to fires of common combustible mine materials. The experiments were conducted in the large-scale Fire gallery located at the National Institute for Occupational Safety and Health (NIOSH) Lake Lynn Laboratory (LLL) in Fairchance, PA, using Ponderosa Pine, Red Oak, Douglas-fir, high and low volatile coals, PVC and SBR conveyor belt, No. 2 diesel fuel, and diesel exhaust. All the experiments (except those using No. 2 diesel fuel and the diesel exhaust tests) were conducted in a similar manner, with combustible materials heated rapidly by electrical strip heaters producing smoldering fires that quickly transitioned into flaming fires. The sensors included a diffusion-type carbon monoxide (CO) sensor, photoelectric- and ionization-type smoke sensors, a video smoke/flame detector, and an optical flame detector. Simultaneous measurements were obtained for average gas concentrations, smoke mass concentrations, and smoke optical densities in order to quantify the levels of combustion products at the alert and alarm times of the sensors. Because the required sensor alarm levels are 10 ppm and 0.044 m-1 optical density for CO and smoke sensors, respectively, the different sensor alarms are compared to the time at which the CO and smoke reached these alarm levels (1). In addition, the potential impact of using smoke sensors that have met the performance standards from accredited testing laboratories is also evaluated using the response of an Underwriters? Laboratory (UL)-approved combination photoelectric/ionization smoke detector. The results are discussed relative to fire sensor needs that can have a positive impact on mine fire safety.

Jan 1, 2012

By E. L. Gillenwater

Coal mine planning has three distinct decision levels: (1) decisions made at the upper level of management that determine production requirements for specific mines, (2) decisions made at the middle management level, the mine level, that determine how the mine satisfies its production requirements, and (3) decisions made at the operating level of management, the sectional level, that determine the sequencing of machine movements at the face. In this paper, the underground production scheduling problem is formulated in multi-stages using the Hierarchical Production Planning (HPP) approach. Two linear programming HPP models for accomplishing decisions at the first two levels are developed. Both models address the aggregate production planning process. The Mine Production Scheduling (MPS) model permits determination of monthly production and inventory levels. The Section Production Scheduling (SPS) model incorporates a quality blending requirement into the determination of weekly sectional production and inventory levels.

Jan 1, 1995

By Alden B. Carpenter

Oil-field brines have been collected and analyzed from Jurassic and Cretaceous rocks in the Mississippi Salt Dome Basin, from Jurassic and Lower Cretaceous rocks, southwestern Arkansas, and from Ordovician and Silurian rocks, southern Michigan. All of these brines are genetically related to evaporites and appear to be brines expelled from halite-bearing rocks, presumably during compaction. The brines in rocks closest to the halite-bearing rocks are uniformly low in lead and zinc suggesting that the metals in metal-rich brines are not acquired within evaporite sequences. The metals in metal- rich brines in Mississippi and in Russia appear to be derived from red beds and may have been originally associated with ferric iron oxyhydroxides. Reduction of these compounds by migrating hydrocarbons appears to release lead and zinc to the associated brines accompanied by the fomation of authigenic ankerite.

Jan 1, 1979

By Robert C. Dunne, Jeffery P. Vaughan

The Archean ores of Western Australia are in total the largest producers of gold in Australia. In addition to numerous small and medium sized deposits, the province also contains the giant Kalgoorlie Golden Mile deposits. A variety of different gold ore mineralogical associations has lead to the development of a number of different processing routes for both refractory and non-refractory ore types. Intense weathering and lateritization of Archean greenstones in the semi-arid Yilgarn region have resulted in the development of a deeply oxidized profile (60-100m) above most sulphide orebodies. Residual and re-deposited supergene gold within iron oxide/silica gangue of this zone responds well to CIP, CIL, heap and vat leaching techniques. Although gold is easily liberated in principal from oxidized gangue, in practice recoveries are sometimes affected by iron oxide coatings on gold grains, and by clay minerals which can interfere with plant performance. Refractory ore types in the Eastern Goldfields fall into three main categories - pyritic, arsenopyritic and telluride-bearing. Pyritic ores may be either free milling or require roasting. The difference appears to depend largely on whether gold occurs along grain boundaries or fractures, which can be liberated by grinding, or whether gold occurs as inclusions within pyrite grains and therefore cannot be satisfactorily liberated by grinding. Arsenopyrite bearing ores are not well understood and are complicated by what appears to be a variable degree of gold solid solution, in addition to included gold. Gold occurring in complex gold-silver telluride assemblages has traditionally been recovered by roasting in the Eastern Goldfields.

Jan 1, 1987

By Arthur P. Nelson

In opening, I want to thank the program committee and members of the Society of Mining Engineers of AIME for the opportunity to speak to you. Various chapters of AIME this past year have expressed interest in the Federal Metal and Nonmetallic Mine Safety Act. We want to see that interest continue, because the reason for the legislation was the safety and health of the industry's workforce. The Department of the Interior was directed by the Congress to administer the provisions of the Act and is therefore held directly accountable for the success or failure of its intent. We intend to see it succeed. Among other things, the Act does provide for education and training under Section 15. This provision has been implemented and is expanding. However, the responsibility of my office is inspection and enforcement and that is my subject today.

Jan 1, 1973

By John A. Organiscak

The Bureau of Mines evaluated a new dust control technique for longwall personnel required to work at the tailgate end of the face. This technique utilizes a water-powered scrubber to clean a portion of the face air, which is discharged behind a brattice partition at the working area. Laboratory simulation of this system in a wind tunnel resulted in average efficiencies greater than 70 pct with system efficiency directly related to scrubber quantity. Underground evaluations indicated a similar direct relationship between scrubber quantity and system efficiency. Gravimetric measurements of respirable dust made during these underground evaluations resulted in average protection efficiencies ranging from 30.7 to 42.5 pct with increasing scrubber air quantity.

Jan 1, 1983

By Y. V. Vasylchuk

An algorithm is presented for optimizing the classification of surface mine material subject to excavating constraints. High-resolution, expected-profit models are optimized to classification maps subject to site-specific excavating constraints. This optimization problem defies traditional closed-form analytical solutions. A practical heuristic algorithm quickly determines the optimum final destination for material subject to realistic selectivity constraints. The expected profit could be calculated from an estimated model if the value calculations are all linear; otherwise, simulation could be used. In both cases, a single expected profit for all destinations on a high-resolution grid is the starting point for dig limits optimization. Maximizing expected profit in a risk-neutral manner is correct given the repeated nature of grade-control decisions over relatively short timeframes.

By James M. Barker

The occurrence of borates and zeolites at Mesa del Alamo is well documented by McAnulty and Hoffer (1) and Lefond and Barker (2). Further investigation indicates the presence of priceite and meyerhofferite in addition to the howlite (1) and colemanite (2). Analcime occurs in addition to the clinoptilolite and phillipsite (2). The Mesa del Alamo area is about 200 !a south of Tucson, Arizona, and 13 km southeast of Magdalena, Sonora, Mexico, just south of the unpaved road to Cucurpe (Figure 1). The geology and mineralogy of northcentral Sonora is known only on a regional basis except for small areas mapped in detail during copper exploration. The study area is within the Basin and Range province of North America from which borates and zeolites are now produced in California. The borates and zeolites at Mesa del Alamo occur in geological environments similar to those of the Mojave and Death Valley regions of California (3, 4). Thus, a detailed exploration pro- gram in the Magdalena area could result in the discovery of economic borate and/or zeolite deposits.

Jan 1, 1979

By John J. Dran

[This paper summarizes the more popular mineral valuation techniques being used by the dining industry, and attempts to demonstrate how they are Interrelated and where some are in error when compared to modern methods of financial analysis. The academic community and the larger and more sophisticated raining companies, have largely rejected the older valuation methods such as the, Hoskold and Morkill concepts and replaced them with "discounted cash flow" (DCF) techniques. The relevancy and usefulness of the older methods have been questioned primarily on the basis of their underlying assumptions that mining companies do not have numerous alternative investments and must use sinking funds deposited at market or ?safe" rates of return to recover the purchase price of mineral reserves. The ability to reinvest In numerous (often non-mining} alternative business ventures, the changing purchasing power of the dollar, corporate income and other taxes, depreciation and depletion allowances, and modern financial management practice, all mitigate against the continued use of the older valuation methods, especially for the larger mining companies. Snail mining companies and Individuals still use these methods largely out of habit and familiarity. This paper attempts to point out the weaknesses and strengths of the valuation methods In current use in the hope that these techniques may be better understood and [rcrn] appropriately applied.]

Jan 1, 1973

By Herbert F. Nyberg

The Black River Falls Mine is owned and operated by Jackson County Iron Company, a wholly owned subsidiary of Inland Steel Company. It is located in vest central Wisconsin, seven miles east of the city of Black River Falls. This is the first taconite plant in the state of Wisconsin. Iron mining started in this area in 1856 but soon failed due to the low grade ore and crude methods of mining and transportation. Inland Steel Company acquired the property in 1939. Some drilling and test work was done in 1940, but the economics of developing the property at that time were not favolable. Improved methods of concentrating and pelletizing in the 1960's made it possible to build the present plant. Due to the limited ore reserve of 45,000,000 tons with expected recovery of 33% it was necessary to limit the capacity of the operation to 750,000 TPY with a life of 20 years. There was some concern about an operation of such limited capacity. A million ton operation was considered the minimum size plant for a profitable operation.

Jan 1, 1976

By P. M. Hawley

In April 1975 Kaiser Steel Corporation and the United States' Department of Energy entered into a cost-sharing agreement for the demonstration of shield-type longwall supports on three consecutive longwall panels at Kaiser's York Canyon' Mine in New Mexico. Under this agreement the Department of Energy supplied 117 Hemscheidt 320 HSL caliper-type shield supports and hydraulic pumps for the duration of the demonstration. The purpose of the demonstration was to educate the U.S. coal mining industry as to the benefits in production, productivity, health and safety, and increased coal extraction afforded by shield-type longwall mining systems and to provide the industry with a working model. A detailed description of this demonstration is given in U.S. Department of Energy Publication No. DOE/ET/12530-T1, entitled "Demonstration of Shield-Type Longwall Supports at York Canyon Mine of Kaiser Steel Corporation," hereafter referred to as the York Canyon Report.

Jan 1, 1984

By C. L. Karr

The efficient management of the distribution of goods and services is important throughout the minerals industry. From the scheduling of processing plant operations, to the routing of work crews in mines, to the planning of product development, vast amounts of time, energy, and money are wasted due to poor planning and scheduling. Thus, the U.S. Bureau of Mines is investigating computational algorithms that can be used to minimize the economic losses related to scheduling and allocating resources. Although there is commercial software available for tackling many scheduling problems, there has been little relief provided for solving the difficult traveling salesman with time windows problem (TSTW). The TSTW problem is a "derivative" of the classic traveling salesman problem, and can be used to minimize the distance traveled by vehicles or personnel to visit all points on a tour, with the additional constraint that each point on the tour must be visited within a specified time window. This paper is a survey of published work in which genetic algorithms have been used to efficiently solve the traveling salesman problem and its more difficult derivative, the TSTW problem. A genetic algorithm is a search algorithm based on the mechanics of natural genetics, and has been used to solve a broad spectrum of engineering optimization problems. Results indicate that the versatility, searching power, and simplicity of genetic algorithms can be used to provide substantial improvement in the area of scheduling and resource allocation.

Jan 1, 1994