Search Documents

By L. "Andy" Anderson, Stephen N. Short, James E. Friant

Since the introduction of "boxhole" drilling in South Africa in 1973, the concept of a blind raise, drilled upward from below, has become an accepted mining practice. A combination machine, capable of constructing raises to a mining level below, or blind raising upward from a single setup position adds a further dimension in versatility. A machine with these dual operating modes was designated by The Robbins Company as the 53R and was introduced into the Western Deep Level Mines, South Africa in 1984. The unit is powerful (200 hp) and compact (18,000 lbs., in a 10 ft x 4 ft 5 inch x 4 ft 6 inch package). This paper describes the design considerations for the new machine, provides field data from early trials, and looks briefly at its overall market and potential.

Jan 1, 1985

By Phil Pennington, D. Jack Adams

Mining and processing of minerals, metals, and fossil fuels can release selenium and arsenic into wastewaters. Both selenium and arsenic are difficult to remove to levels that meet current drinking water and discharge criteria. These metalloids can be used as electron acceptors by microorganisms transforming them back to reduced states, thus removing or stabilizing them. Bioremediation cost effectiveness will be discussed in terms of site information required, microbial populations, co-contaminants, pH, redox, and nutrients. Full-scale, economical ex situ and in situ biotreatments are possible and can produce 1,000’s of times less sludge than conventional precipitation technologies.

Jan 1, 2005

By Christopher J. Bise

INTRODUCTION The principal means for transporting men, supplies, and mined material in an underground or surface mine are rail systems, conveyor belt systems, or a combination of the two. Typically, large underground mines use rail haulage from the mining sections to the hoist, with conveyor belts being used within the sections. Small mines use conveyor belts in the mains and sub- mains as well as in the panels. The size and layout of surface mines also contribute to variations in the way these haulage systems are applied. The following sections address the typical problems confronting mining engineers in designing these haul- age systems. For rail, these include rail selection and turnout design, locomotive tractive-effort calculation, and motor sizing. Belt haulage calculations include belt width and speed specifications, tension and take- up requirements, idler spacings, and motor sizing. TRACK LAYOUTS Introduction The adequacy of mine track layouts is dependent upon such factors as rail weight (Table l), suitable ties, a well-drained roadbed, and properly designed curves, grades, and track alignment. As long as the installation conforms to the manufacturer's recommendations, good service can be expected from the rail system. Typically, mining-engineering calculations for rack layouts have dealt almost exclusively with the design of turnouts. As such, the following section provides the necessary information for computing the theoretically correct dimensions of turnouts. Turnout Design Fig. 1 shows a typical turnout with an identification of the component parts. Fig. 2 identifies the variables that are used to determine the turnout dimensions. The formulas that concern the mining engineer are those listed: [ ]

Jan 1, 1986

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals and Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles.Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Vishal Gupta, member SME, of EP Minerals LLC, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Vishal Gupta, member SME, of EP Minerals LLC, Agricultural Materials.• Joe Garska, member SME, of Imerys, ceramics and refractory materials.• Stanley Krukowski, member SME, of the Oklahoma Geological Survey, chemical raw materials.• Russell Winn, member SME, of R.E. Janes Gravel Co., chemical raw materials.• Justin Zdunczyk, member SME, of Pike Industries, construction aggregates.• Jerry Gauntt, member SME, of Golder Associates, fillers and pigments.• Ebrhaim K. Tarshizi, member SME, of the Michigan Tech, sorbents, filters and process aids.• Daniel T. Eyde, member SME, of St. Cloud Mining, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.Virta, R.L. U.S. Geological Survey, National Minerals Information CenterFour companies - H.C. Spinks Clay Co., Inc., Imerys, Old Hickory Clay Co., and Unimin Corp. - mined ball clay in four states in 2013. On the basis of preliminary data, production was 1 Mt (1.1 million st) with an estimated value of $47 million. Production increased by 3 percent in tonnage from 973 kt (1.1 million st) with a value of $45.1 million in 2012. Tennessee was the leading producer state accounting for 64 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 67 percent of total ball clay production was airfloat, 22 percent was crude or shredded and 11 percent was water-slurried.ConsumptionIn 2013, domestic ball clay producers sold clays to the following markets: ceramic floor and wall tile (44 percent); exports (21 percent); sanitaryware (18 percent); miscellaneous ceramics (9 percent); fillers, extenders, and binders, and unspecified uses (4 percent each), based on 2012 end use patterns and current markets. Other markets accounted for less than 1 percent of the remaining ball clay sales or use. Sales reported for the manufacture of fiberglass or most filler, extender, and binder applications were likely to have been mainly kaolin mined or purchased by the ball clay producers.PricesThe average value of domestically produced ball clay was approximately $47/t ($43/st) in 2013 compared with $46/t ($42/st) in 2012, on the basis of a preliminary survey of domestic ball clay producers. The unit values of exported and imported ball clay were $126/t ($114/ st) and $373/t ($338/st), respectively, in 2013, compared with $62/t ($56/st) and $314/t ($285/st), respectively, in 2012. Unit values for most large export shipments increased in 2013, and a larger number of low-tonnage, high-value export shipments were shipped in 2013 than in 2012, resulting in a doubling of the average export value. Two low-tonnage, high-value shipments in 2013 accounted for the increased value of imports."

Jan 1, 2014

By S. K. Gilman

Zircon (ZrSiO4) sand production of about 1.1 Mt/a(1.2 million stpy) predominates the global supply of zirconium minerals. Baddeleyite (ZrO2) contributes less than 1 percent of supply. Zircon is almost exclusively produced as a co-product from the mining of titanium minerals, mainly from mineralized beach sands. In 2004, there were a number of new projects under consideration that were more dependent on zircon revenue than for titanium minerals. This reflected sustained higher zircon prices and forecast ongoing supply shortages in the absence of major new discoveries.

Jan 1, 2005

By Jimmy Thompson

The Santa Clara Valley Transportation Authority is designing the Silicon Valley Rapid Transit Project in San Jose, California. The project includes 6.9 km (4.3 miles) of twin-bored tunnels to be constructed through downtown San Jose using two earth pressure balance machines (EPBMs). This paper begins with a project description and update of the project status followed by a description of the relationship between anticipated ground conditions and EPBM requirements. Topics addressed include soil conditioning, abrasion resistance, annulus grouting, face pressure estimation, additional pressure control devices and control measures to limit over-excavation and settlement.

Jan 1, 2008

By M. Newton

Optimization and sensitivity analysis of mineable economic volumes have been standard practise for open pits for many years now, and more recently software has become available to apply techniques for delineating mineable reserves for underground mines. In general these techniques have been applied to a single resource model to quantify mineable tonnes and grade for underground mining. However by using multiple conditionally simulated models both the risk associated with the mining parameters and the risk associated with variations in grade, tonnes and profit can be quantified. Using suitable software the mine planner can then easily and quickly define and compare alternative designs to assess and improve the robustness of and the confidence in the final design.

Jan 1, 2007

By William H. Dresher

Introduction A subject long debated but rarely resolved involves the interaction between the academic community and industry in the sponsorship and conduct of research. The subject is, unfortunately, too often treated as a controversy involving ethics and the profit motive. But, in fact, the two branches of society - industry and academia - are necessarily part of the same system. In the last 25 years, the realization has developed that research alone is not sufficient to bring about use of those results to benefit society through productivity gains and economic growth. The flow of events shown in Fig. 1 was generally believed to be the steps required for reaping the benefits of research. Today, research still has the very important role of creating new information or new ideas. However, it is recognized to be but one of many steps in a process that we now refer to as technological innovation. Charpie (1967) said, "Technological innovation is the driving force behind economic growth in the US. In this context, innovation means the process by which a new idea is successfully translated into economic impact within our own society, by providing better products, and simultaneously creating new jobs in the manufacturing of those products. Only after an investigation is put into sufficient use to have an economic effect, is it termed an innovation." One of the best depictions of the technological innovation process is shown in Figs. 2 and 3. These are adapted from Haeffner (1975), and modified by the Committee on Mineral Technology of the National Research Council (1981). Figure 2 identifies the many steps involved in the process. It designates a generalized form for interaction between the academic community and industry. Figure 3 identifies the steps in the "innovation activity" box of Fig. 2. Academia is generally responsible for developing of new knowledge and ideas, as well as maintaining and enlarging the collected body of scientific knowledge. Industry is responsible for developing new products, methods, and processes. Both institutions operate for the benefit of society, but under different driving forces. In academia, the driving force is the achievement of academic excellence. In industry, the driving

Jan 10, 1984

By S. Watkins, D. Apel, B. Gray, R. Moss

Currently, there are several techniques and technologies available which are used by mining industry in its attempts to remotely monitor the ground movements both at surface and underground mines. The currently available remote distance meters and distance change monitors mainly use phase change and time-of-flight techniques. The described monitor uses triangulation technique to track position of an optical spot projection and then image processing to measure mine wall movements. The system can be easily automated and poses no obstruction to mine traffic. The position of an off-normal laser spot will shift as the target wall moves. The described ground movement monitoring system has potential for superior accuracy and target monitoring can be made through air (gaseous) or other transparent media. The theoretical accuracy and range of this system depends solely on the resolution and focal length of the camera being used. The remote capabilities of the system make it uniquely suited to applications where monitoring is required in high-traffic, inaccessible, or unstable and dangerous areas of a mine.

Jan 1, 2007

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By J. Chai

In order to find the behavior of dewatered unconsolidated strata during the process of injecting water through a borehole, a new type of fiber Bragg grating (FBG) sensing system was successfully used for the real-time strain monitoring of unconsolidated strata during a water injection process for a dewatered unconsolidated strata of a coal mine. The unconsolidated strata water injection test was implemented through a borehole at a depth of +115.83 to +135.15m. The employed FBG strain monitoring system and ground water level observation system were installed at the depth in the unconsolidated strata where the water injection was conducted through two different boreholes. The water injection pressures in the test were 0.1, 0.2, 0.3MPa respectively, and the total water injection volume was 4226.84m3. The relationships between the water injection pressures, water injection volume and the strain change of the unconsolidated strata, the stress and strain conditions of the unconsolidated strata before and after water injection, were analyzed. This paper presents the results of these tests, and shows that the dewatering compression of the unconsolidated strata is reduced with increasing water injection pressures and water injection volumes. Comparing the stress-strain conditions before and after water injection, it is found that the stress of the water injection strata is in tension, which confirms the theory that the settlement of the thick unconsolidated strata is directly caused by the reduction of ground water levels. The high sensitivity and stability of the FBG monitoring system used was able to realize the real-time strain monitoring of the water injection process within a deep unconsolidated strata. This FBG monitoring system and the test results presented are very important for understanding further treatment of settlement in unconsolidated strata.

Jan 1, 2012

By E. Arioglu

Discussion by E. Arioglu Y. Luo and S.S. Peng are to be congratulated for their outstanding paper providing new results from surface subsidence monitoring over longwall panels under different conditions. This writer found the authors' paper very interesting. In reference to this paper, the following contributions are offered: • In the paper, the maximum possible subsidence [(ASmax)] induced by chain pillar convergence has been related to a parameter (h/1- p) by linear regression. (Notations are expressed in this discussion's Fig. 1 (b).) It is a well-known fact that in a goaf the roof lowers onto broken material that gradually compacts. Then the physical behavior of goat may closely follow the compaction characteristics of broken materials. In light of this assumption, a mathematical means (Fig. 1(a)) of defining the expected compaction (i.e. surface subsidence) represents an exponential expression between [ASmax/m vs. h/1-p]. This is based on Luo and Peng's field observations from the Appalachian, Illinois and Alabama coal fields. (The coefficient of regression "r" under consideration was computed to be 0.883). • According to Wardell's (1969) findings for board and pillar mining, the maximum possible subsidence can be expressed in terms of maximum pillar loading (depth, ratio of extraction) and the height-to-width ratio of the pillars left. Using Luo and Peng's 1991 results, this writer discovered a regression equation between the above-mentioned factors. As displayed in Fig. 1(b), the functional expression approximates as closely as possible the observed subsidence data. It may be noted here that Wardell's approach (1969) can be successfully utilized for longwall panels having chain pillars. Reference Wardell, K., 1969, "Ground surface and control," Mining Congress Journal, January, pp. 1-7.

Jan 1, 1993

By A. Arik

An accurate estimation of mining block grades continues to be a challenging task for ore reserve practitioners. Two of the factors that affect the accuracy of the estimates are the estimation method used and the variability of the mineralization in the deposit. The objectives of the study are twofold: Firstly, to see how different estimation methods perform on a given deposit. Secondly, to determine the impact of particular nature of the mineralization on the results. The comparison of several estimation methods for the prediction accuracy is performed using the conditional simulation results as the basis.

Jan 1, 2000

By Steve Kral

Worker safety is an issue that transcends industries, whether it be mining, construction, manufacturing or even general office work. In the mining industry, safety and training are particularly important because mining is a dangerous occupation. Throughout the years, federal and state safety regulations have been written and revised to keep up with the changing technologies. And mine operators have installed their own safety and training programs. They have come to realize that a safe and healthy workforce has positive effects on productivity and profitability —not to mention avoiding the high costs of injury-related absenteeism.

Jan 1, 2003

China’s vibrant economic growth is built on coal, the source of two thirds of the country’s electricity. Over 95 percent of China’s coal is mined underground with the average mining depth at 410 m and in-creasing at 10 m per year; today, the deepest Chinese coal mines have exceeded 1,000 m. With increasing mining depths, there are greater challenges including increased methane emissions and spontaneous combustion. According to the government, nearly half of China’s coal mines are classified as gassy (with specific gas content at least 10 m3/mt). Coalbed methane (CBM) is a clean energy source. However, only a small percentage of the methane is captured, and the rest is vented directly to the atmosphere. This paper describes China’s CBM resource, its production and utilization.

Jan 1, 2006

By W. H. Pomroy

In its 2001 diesel particulate matter (DPM) rule for metal and nonmetal underground mines, MSHA established an interim concentration limit of 400 micrograms of total carbon (TC) per cubic meter of air (400TCµg/m3), and a final concentration limit of 160TCµg/m3, to be phased in over five years. Following a court challenge to the 2001 rule, MSHA, industry and organized labor reached a partial settlement of the litigation under which the agency agreed to issue a proposal to amend the 2001 rule by, among other things, changing the surrogate from TC to elemental carbon (EC), applying MSHA's traditional hierarchy of controls, and revising requirements for one-year special extensions for complying with the final DPM exposure limit. MSHA issued a final rule in 2005 converting the interim concentration limit from 400TCµg/m3 to 308 micrograms of EC per cubic meter of air (308ECµg/m3) based on a miner?s personal exposure. Pending further rulemaking, MSHA retained the final concentration limit of 160TCµg/m3. In May 2006, MSHA issued a final rule that clarified that the final limit of 160TCµg/m3 would be based on a miner?s personal exposure rather than as a concentration limit. The 2006 rule also phased in the final DPM limit in three steps over two years, beginning in May 2006 at 308ECµg/m3, followed eight months later in January 2007 with a limit of 350TCµg/m3, and finally reaching 160TCµg/m3 in May 2008. Also in the 2006 rule, MSHA committed to converting the 160TCµg/m3 limit to an EC limit in future rulemaking. This paper reviews the DPM exposure limits in the context of the MSHA rulemakings and discusses the DPM engineering controls that were utilized by mine operators to attain compliance with each progressively lower limit.

Jan 1, 2009

The ability to optimise a concentrator from mill feed to final products requires a simulator which integrates comminution, classification and separation modelling. In order to model this range of processes, such a simulator must handle a variety of information about the ore. The AMIRA P9 project has developed a whole-of-concentrator simulation capability which brings together a texture-based model of mineral liberation, quantitative X-ray micro-tomography analysis to measure the inputs required by this model, and a multi-component simulator software framework. In the context of this approach, the term ?multi-component? implies the ability of the simulation to handle many particle properties simultaneously; for example size, composition, density, floatability etc. The simulation software framework provides the means to manage the flow of data around a circuit flowsheet, allowing each process model to access the information relevant to that particular model. A case study based on plant data from a gold-bearing pyrite concentrator is used to demonstrate the capabilities of the multi-component approach in simulating circuits which contain comminution and separation processes.

Feb 27, 2013

By V. T. McLemore

In-situ leaching (ISL) operations have been proposed to recover uranium from sandstone-uranium deposits in NM. ISL (also known as in-situ recovery, solution mining, solution-leach mining, leach mining) consists of injecting a leaching solution into the mineralized zone through injection wells. The leach solution migrates through the formation, dissolves uranium and is recovered through production wells. The uranium is then precipitated through a conventional uranium recovery system. Several criteria must be met in order for in-situ leaching to be successful, most important is that the ore body must be amenable to chemical leaching. A number of ISL operations have been conducted in NM in the past (Mobil, Crownpoint; UNC-Teton, Section 23; Grace Nuclear, Hook?s Ranch, Seboyeta, Church Rock; Anaconda, Windwhip). Kerr-McGee (later Quivera Mining Co., Rio Algum) successfully produced uranium from mine-water recovery (recirculated mine water) from the Ambrosia Lake mines (mid-1960s to 2002). Despite some difficulties, ISL is a viable alternative to recovering uranium and could be utilized in the Grants district with proper aquifer characterization and monitoring.

Jan 1, 2009

By Russell Miller, Fun-Den Wang

High Pressure Water Jet Assisted Tunneling The high pressure water jet assisted tunneling project was conducted in a granite quarry near Skykomish, Washington, approximately 90 miles east of Seattle. A 7-ft diam tunnel boring machine was modified and equipped with high pressure water jets. The concept that tunneling rates can be improved by using high pressure water jets was validated, with an average increased advance rate of 50% to 60%. For some tests, the advance rate was more than doubled. A comprehensive economic analysis has shown that very significant savings are possible. At a 50% increase in advance rate, cost savings of 14% and 24% were projected for 10-ft and 20-ft diam tunnels respectively. These benefits were seen to be relatively insensitive to water jet equipment costs.

Jan 1, 1976