Search Documents

By W. L. Dare

Tri-axial strains in pillars, created by pillar robbing, were measured in an experiment at the Dysart No. 1 uranium mine near Grants) New Mexico. At this mine, room-and-pillar stoping is used on the advance, and pillars are recovered on the retreat. The are deposit is, for all practical purposes, horizontal. Measuring devices were installed in pillars approximately 90 to 200 feet from the break line, and strains were recorded over a 4-to 6-week period. The measurements indicate that, in general, the algebraic magnitude of vertical strains increased, and the horizontal strains decreased, in turn, indicating that vertical (or near vertical) loads on the instrumented pillars lessened as pillars were recovered.

Jan 1, 1962

By L. K. Weaver

The objective of this study is twofold, The first is to present the composition of the offshore petroleum industry in terms of lease bonuses and the value of hydrocarbons produced from Federal offshore tracts. The second is to present costs of producing petroleum (oil and condensate) in the Gulf of Mexico with a financial analysis of an offshore operation. To prepare a financial analysis of an offshore operation, a model was derived to show the costs necessary to explore, acquire, develop, produce, and abandon a 5,000-acre block and the estimated income from the sale of the hydrocarbons produced. To establish cost and income guidelines for the model, a group of seven oilfields in the Gulf of Mexico ranging from 7 to 75 miles from shore and in water 20 to 130 feet deep was selected for study. A net profit or loss statement was prepared for each field and a discounted cash flow rate of return was calculated. Discounted cash flow rates of return for the seven fields range from 1.1 to 19.5 percent. Under the two specified conditions set up for the model (a 20-year and a 30-year oil depletion model), the rates of return are 17.2 and 13.7 percent, respectively. To January 1, 1959, the top four operators in the Federal offshore areas had paid approximately 40 percent of the amount spent on all lease bonuses and produced about 56 percent of the total hydrocarbons.

Jan 1, 1972

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By Joseph A. DeCarlo

Coal is one of our basic sources of energy (heat, power, light) and an essential raw material for most metallurgical processing. More than two-thirds of the electricity currently produced by thermal powerplants in the United States is generated by coal, and it is expected that coal will continue to be the major fuel used for this application at least through the 1970's. Coke produced from bituminous coking coal is the principal fuel of iron blast furnaces, and unless ironmaking methods change greatly, coal will continue to maintain a dominant role in iron-ore processing and steel manufacturing for many years. Export markets are expected to increase also, adding to the overall increased demand for coal. Accompanying the increased total requirement, however, will be an ever-increasing demand for higher quality coals, specifically, coals of low sulfur content. Except for special-purpose coals such as those used for the production if coke and ceramics where impurities in the fuel contaminate the end product, the amount of sulfur in coal has been only a minor consideration in the selection of a particular coal for fuel. Major considerations, particularly for the coals used to generate electric power, have been availability and cost. An increased national concern for control of air pollution, however, particularly that resulting from the emission of sulfur oxides in stack gases to the atmosphere, has led to more rigid specifications on coal quality, and the sulfur content of coals will become increasingly more important in the future.

Jan 1, 1966

By J. R. Thoenen

This circular is part 6 of the third paper (entitled "Excavation") of a series summarizing the technical problems involved in the production and preparation of sand and gravel. Part 1 discussed the use of power shovels, draglines, and excavator cranes; part 2, power scrapers, slackline cableway excavators, and hydraulic monitors; part 3, hydraulic, clamshall, ladder, and diaper dredges; part 4, haulage equipment, particularly industrial cars with locomotive or hoist as the motive power; part 5, conveyor belt, motor truck, pump and pipe line, towboat and barges, and aerial-trams haulage. This circular discusses the application of these various types of equipment to the different types of sand and gravel deposits and contains a reference bibliography. It completes the discussion of excavating problems.

Jan 1, 1936

By Albert L. Toenges

The purpose of this paper is to describe some of the methods and practices of mining coal mechanically where more than one shift is worked, with the view of determining the advantages and disadvantages of various types of equipment and mining systems now in use. This paper is in the nature of a progress report, and, as the number of mines discussed in it is limited, the conclusions drawn in the comparison of various systems are not final but may be revised after subsequent investigations. Physical conditions vary in different and in the same mining districts and determine, more

Jan 1, 1938

By G. M. Martinez

The Bureau of Mines has investigated methods for the recovery of byproduct heavy minerals from sand and gravel operations in Oregon and Washington. These heavy minerals are not currently recovered except for gold in a few areas. The recovery of byproduct heavy minerals would provide a domestic source of minerals presently imported, and a more efficient use of domestic resources would be accomplished. Samples from more than 40 locations were treated by gravity separation to yield heavy mineral concentrates (black sands). Magnetite, ilmenite, zircon, rutile, chromite, platinum-group minerals, radioactive minerals and gold were identified in the concentrates. Individual zircon, ilmenite, chromite; magnetite, and gold products were recovered from selected concentrates by low-and high-intensity magnetic, high-tension, and heavy-medium separation techniques. The recovery for the individual mineral products ranged from 67 to 95 pct.

Jan 1, 1981

By G. N. Schrauzer

Work has been carried out in the development and testing of carbon monoxide (CO) detection devices which use silica-gel impregnated with metal salts. If carbon monoxide is present, the ?detection gel? (the treated silica-gel) changes from a yellow to a blue-green or blue color. The detection gel "regenerates", i.e., returns to its original yellow color, within 4-24 hours after removal from air containing CO. The detection gel exhibits a threshold of CO response which can be adjusted over a wide range of CO concentrations, typically from 50-500 ppm in air. The preparation of detection gel using salts of palladium, molybdenum and copper is described. Also reported are the results of testing the detection gel&apos;s response to carbon monoxide under varying conditions of temperature and humidity and in the presence of some potentially interfering gases. Low levels of hydrogen sulfide (~ 5 ppm)1 nitrogen dioxide (< 7 ppm), and acetylene (> 200 ppm) were found to affect the detection gel. Temperature and humidity were also found to affect the detection gel&apos;s response. Increasing temperature shortens the gel?s response time while increasing the humidity delays the gel?s response and alters the threshold of the gel. A brief discussion of the further research and development necessary to stabilize the detection gel?s desirable characteristics is included. Descriptions of testing equipment and procedures are covered in detail.

Jan 1, 1978

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

By William F. Hahn

This report describes an illumination system suitable for use in a slope under construction, Simulator work was performed using actual lighting hardware to verify adequate light levels to meet MSHA proposed regulation (as published in the Federal Register, January 13, 1977). The sequence of operating activities for two different slope driving sites are discussed and lighting requirements are defined for each,

Jan 1, 1981

By K. Biswas, S. Iverson, S. J. Jung

Computer modeling of rock flow in ore passes is being investigated and compared using MSC Soft-ware’s Working Model 2D1 (WM2D) and Itasca Corp.’s Particle Flow Code in Two Dimensions (PFC2D). This work is being carried out by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health to determine the usefulness of computer modeling to improve ore pass design. The types of tests included pendulum tests to validate WM2D simulations and simulated single-rock drop tests in both WM2D and PFC2D to understand their contact models. Simulated rock impacts at the ore pass chute and the use of inclined ore passes and doglegs were investigated in both programs. A PFC2D simulation showed that dynamic loads at the chute gate were reduced significantly when a dogleg transition was used, and simulations in which the ore pass was inclined showed significant reductions in chute impact loads compared to simulations of a vertical ore pass. A released hang-up was simulated using PFC2D.

By E. Kamon

This report summarizes completed research pertaining to the reaction of human subjects exposed to Self-Contained Breathing Apparatus (SCBA) stressors during escape conditions (viz., resistance breathing, C02 breathing, hot air breathing, and static positive facepiece positive pressure breathing) and the development of an automated breathing and metabolic simulator (ABMS). Volume I contains summarizes of the studies performed under this contract. Volume II is an appendix which contains more detailed descriptions of these studies.

Jan 1, 1984

By Kenneth Trelewicz

This report describes the total effort that went into developing environmental test criteria for general mine instrumentation. The project was a two-phase effort. Phase I consisted of research and mine visits to develop an environmental profile for mine instrumentation. The profile was translated into general requirements and then into test requirements. A review of existing government and commercial specifications was performed to determine if they matched mine instrumentation test requirements. Finally, a set of environmental test procedures was developed for the testing of mine instrumentation. Phase II consisted of selecting and purchasing sample mine instrumentation and subjecting them to the previously developed tests. The purpose was twofold: (1) to evaluate the criteria developed for use as an instrumentation test document and (2) to determine the effects of the various criteria on a representative sample of both proven and newly developed instrumentation. The test criteria were then modified, based on the results of the testing, and are listed therein.

Jan 1, 1981

By Robert M. Baker

This document details the method whereby Allen Corporation of America gathered and analyzed data and developed an annotated bibliography of metal and nonmetal mine fire reports (1950-1979). The primary objective of this program was to develop the annotated bibliography which included MSHA accident reports and periodicals. Two additional objectives were to gather data on non-reportable fires and to conduct statistical analyses on the data to delineate trends. Data was acquired from three major areas: periodicals, MSHA fire reports, and mine safety directors. Data was separated into reportable fires (at least ½ - hour duration or injury), non-reportable fires, and opinion data. The data was then analyzed by time trends, state, ore, ignition source, burning substance, location, equipment, detection, duration, injuries, fatalities, and successful extinguishing agent. The authors make a number of recommendations: (1) improved stationary electrical equipment design and fire protection, (2) improved design of mobile equipment to separate combustibles from ignition sources, (3) improved maintenance, (4) improved housekeeping, and (5) improved training. The document is divided into two volumes and an appendix. Volume I contains data acquisition procedures, data analysis procedures, and conclusions and recommendations. Volume II contains a chronological list of mine fires and fifteen indexes to assist the reader in locating fire incident report of interest. The Appendix contains the annotated bibliography of over 300 metal and nonmetal mine fire reports and journal articles and a list of non-reportable fires.

Jan 1, 1980

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. This volume deals with the development of a microcomputer based training cost model (TCM) which can be used to analyze training cost implications of various types of training. The model has been developed using Aston Tate&apos;s dBASE III plus language. The computer program and a test run of the model are presented in this report.

Jan 1, 1993

By W. W. Aljoe

The use of protective canopies can result in canopy roofing and/or serious restrictions to operator comfort and vision. To document this experience, BCR conducted a field study of cab and canopy design and application which resulted in a catalog of 164 canopy designs and an analysis of field data which showed no simple relationship between working height and canopy-related problems. The relationship also involves (1) machine frame height, (2) mine floor undulations, (3) operator compartment dimensions, (4) canopy design and location on the machine. Data analysis indicates (1) present technology does not always permit successful application of canopies in working heights below 42 inches, and (2) development of satisfactory low-coal canopies is doubtful. The basic conclusion of the study is that future R&D studies should be directed at development of alternative protection systems and remote mining methods.

Jan 1, 1981

By Thomas M. Barczak

Wood cribs are used extensively to stabilize openings in underground coal mines. This U.S. Bureau of Mines report describes the results of full-scale testing of several multitimbered wood crib configurations. Multitimbered configurations are wood cribs that are constructed with two or more timbers per layer. Nine different crib configurations were evaluated. Configuration parameters under study included the aspect ratio (height-to-width relationship) and the percentage of solid rr:aterial used in crib construction. Test results and generalized wood crib behavior are discussed and recommendations are made concerning crib constructions to maximize strength and stability. Crib performance is enhanced by reducing buckling effects by decreasing the aspect ratio and geometry considerations that increase the moment of inertia. A cost benefit analysis of multitimbered wood crib configurations is made. Generally, increasing the percentage of solid provides more resistance at less unit construction cost. A comparison of laboratory results and underground observations of several wood pack wall supports suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load-bearing capability include load rate effects, stiffness of reaction surfaces, and varying boundary conditions that alter the load transfer mechanics of the crib structure.

Jan 1, 1991

By Jr .. Ebbley

The investigation of mine shafts and underground workings at Leadville, Colo., was started in May 1946 and recessed in November 3, 1946. Thirty-eight shafts and connecting accessible underground workings, comprising about a third of the accessible shafts in the district, were investigated. The Leadville district, a former important producer of lead and zinc, was considered by the Bureau of Mines to be capable of bolstering &apos;the waning domestic output of .these important metal. Accordingly, the investigation was initiated for the purpose of. .obtaining more definite data on sulfide and oxide reserves, evidence to justify completion of the Leadville drainage tunnel, representative large samples of the complex oxidized and mixed ores for testing to determine methods, beneficiation factual data to be supplied to property owners in order to stimulate production, and to determine the more favorable areas for development by the Bureau.

Jan 1, 1949

By Charles E. Whieldon

Data on the oil fields in Mahoning Columbiana, Carroll, Jefferson, and Harrison Counties, Ohio, were collected from scattered sources and com- piled to make the information readily available to operators who may be interested in conducting secondary-recovery operations in the area. General geology, oil production, oil-productive acreage, core data, reservoir calculations by townships, and miscellaneous data and reference material are presented.

Jan 1, 1965