Search Documents

By R. R. May

A preliminary examination of the Houston strip-coal mine, situated on the Alaska Railroad at milepost 175 (61 rail miles north of Anchorage, Alaska) and a review of all available information resulting from early coal exploration activities in the area resulted in plans to investigate the coal-bearing formations at depth by means of diamond core drilling to indicate the existence of additional reserves of coal in close proximity to railroad transportation, where it would be quickly available to meet rapidly expanding military and civilian fuel requirements. From the date of mobilization of equipment, August 28, 1951, until date of suspension, August 18, 1952, 2,010 feet of diamond drilling was completed. Ten definable coal beds were cut, of which 2 appear to be persistent and minable over an area of approximately 1/2 square mile. Within this area the 2 minable beds contain approximately 5,000,000 tons of coal in place. Of the remaining beds, at least two others may be minable to the eastward near their projected outcrops; however, these and deeper beds (at least in the vicinity of the drill holes) lie beneath a zone of pressurized gas and brackish water. From a practical standpoint, continued development and utilization of the coal in this vicinity will depend on the operators' ingenuity in developing cheap mining methods and on diligent prospecting for strippable coal under the comparatively light glacial cover.

Jan 1, 1957

By Richard Havens

A flotation procedure was devised by the Federal Bureau of Mines for beneficiating Mount Wheeler, Nev., beryllium ores that contain the beryllium minerals bertrandite and phenacite in a complex association with calcite, fluorspar, mica, quartz, and other accessory minerals, The method also has proven to be effective in trials on ore from the Lake George, Colo., area. Samples used in most of the research ranged from 0.49 to 0.73 percent BeO. Beryllium mineralization varied from two-thirds bertrandite to all phenacite. An unusually high grade sample containing 5 percent BeO as phenacite was floated on a batch basis to prepare concentrate for utilization studies. The beryllium minerals were floated from undeslimed pulps at natural pH using sodium fluoride and sodium hexametaphosphate (HMP), as modifiers, and a fatty acid-fuel oil combination as the collector. Key factors were the use of a minimum of about 4 pounds of sodium fluoride and between 2 and 4 pounds of HMP per ton of ore. Efficacy of the HMP was related to the grind, mineralogical composition, corollary reagents, and type and time of conditioning. Addition of the fluoride, HMP, and collector in that order, followed by appropriate conditioning after each addition, was essential for satisfactory flotation.

Jan 1, 1961

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing and grinding methods, and costs, at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The, cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the methods employed by the Evans Pipe Co., Uhrichsville, Tuscarawas County, Ohio. The author wishes to acknowledge the assistance of the following company officials: T. J. Evans, II, president; T. J. Evans III, vice president and general manager; and L. P. Young, general superintendent.

Jan 1, 1936

By Ted A. Lewtas

The effectiveness of induction fans in ventilating dead headings was studied in the laboratory and underground. The following fan attachments were evaluated: a. Aerodynamic nozzle b. Various lengths of vent tube c. Honeycomb airflow straightener. Various fan locations were also tested. The following conclusions were reached: a. A nozzle on a fan located against the drift wall gives the greatest jet penetration distance. b. Air straighteners are ineffective in increasing jet penetration. c. Induction fans are ineffective in removing contaminants from dead headings without sufficient main ventilation flow.

Jan 1, 1980

By David E. Fogelson

The breakage of rock by explosives depends largely on the ability of an explosive to transfer its stored potential energy to the rock as strain energy. Therefore, the relative rock-breaking abilities of explosives can be determined indirectly by determining the relative amounts of strain energy transferred to the rock at the time of detonation. This report presents experimental data on the strain energy contained in explosion-generated strain pulses in a granite gneiss. Six explosives were tested. The scaled total radial strain energy Es/W flowing outward through a spherical shell of scaled radius R/W1/3 surrounding the point of detonation was found to follow an exponential decay propagation law of the form [ ]

Jan 1, 1959

By M. C. Malamphy, A. H. Reed, G. K. Dale, T. M. Romslo, A. Ollar

"PREFACEA general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourth. The data are accompanied by maps showing the location of holes drilled and the deposits developed.Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township.The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on Figure 13 in Volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes.Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township is given with the discussion covering that area."

Apr 1, 1948

By R. L. Crosby

A part of the liquidus of the magnesium-zirconium system was determined by chemical analysis of suction samples taken from the melt in the approximate temperature range of 850° to 1,450° C. The melt was prepared in a furnace pressurized with an inert gas. The average zirconium value in weight-percent of the liquidus composition at each sampling temperature was 0.96 at 867° C, 1.40 at 1,062° C, 2.05 at 1,262° C, and 2.96 at 1,402° C. The equilibrium solid phase was zirconium.

Jan 1, 1965

By Fred N. Kissell

Air recirculation caused by dust scrubbers at coal mine working faces was examined by the Federal Bureau of Mines with regard to the potential hazards caused by a possible buildup of methane gas. A theoretical analysis indicated that there was no apriori way to predict the effect of scrubber recirculation on methane concentration levels. Experiments conducted in a full-scale model of a working face area indicated that methane levels were dependent to a great extent on the location of the scrubber exhaust, but that the scrubber recirculation did not substantially increase the methane concentration above those levels that would have prevailed were the scrubber not in operation. An analysis of two underground scrubber trials showed that the scrubbers had no significant effect on methane levels, and a review of explosions attributed to recirculation showed that these were characterized by a lack of fresh air as well as recirculation. It was concluded that high methane levels are due more to a lack of fresh air than to recirculation.

Jan 1, 1975

By Eugene T. Sheridan

The annual survey of the fuel-briquet industry by the Bureau of Mines, United States Department of the Interior, revealed that 21 fuel-briquet plants in 11 States were in operation and reported production in 1956. The demand for fuel briquets in the United States has gradually declined since 1948, and the number of operating plants has decreased from 36 to 21. Also, the annual productive capacity of the industry has decreased, although not a proportionate amount because most of the plants that were abandoned were small and in most instances had a designed capacity of less than 25,000 tons per year. In 1956 the 21 active plants had an annual capacity of 3.7 million tons (table 2), which was only 20 percent less than the total capacity of the 36 plants in 1948. This indicates that most of the larger plants have remained active, even though operating at reduced rates, and the average capacity of the industry has increased from 130,000 tons per plant in 1948 to 177,000 tons in 1956. Since 1948 operating rates have decreased from 67 percent to 41 percent of annual capacity.

Jan 1, 1958

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide alumina production capacity by plant and country. The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1993. Capacity data represent announced installed and planned capacities and do not necessarily reflect a Bureau of Mines judgment of actual plant operating levels or timing of planned expansions, The year-end capacity is the ?nameplate" capacity or estimated production capacity, whichever is larger.

Jan 1, 1993

By Arno C. Fieldner

Forty years have elapsed since the Bureau of Mines was established on July 1, 1910, by Act of Congress. The convocation of this Sixth International Conference of Safety in Mines Research Directors, 24 days after our 40th birthday, seems to be an appropriate time for reviewing our contributions to mine safety research and the problems yet to be solved from the American point of view. Actually research on safety in coal mines was started by the United States Government in the Technologic Branch of the U. S. Geological Survey of the Department of the Interior in 1908, as a result of a succession of disastrous coal mine explosions in which many lives were lost. In 1910 this work was transferred to the newly created Bureau of Mines. 394 lives were lost annually per 100,000 men employed in the coal mines of the United States in the 5-year period ended in 1910, as compared to 203 lives lost annually in the 5-year period ended with 1949. In 1908 no safe, permissible types of explosives and no certified permissible equipment of any kind were used in American coal mines. Black powder was in universal use and open oil or acetylene lights were common in all but mines known to be gassy. Rock dusting was not practiced to limit propagation of explosions, nor was ventilation in many mines adequate, Our safety practice lagged behind that of foreign coal- mining countries and therefore one of the first steps in carrying out the Congressional Authorization of 1908 to investigate the causes of mine explosions was to obtain assistance from the leaders of mine safety research in foreign countries. At the request of Dr. Joseph H. Holmes, director of the Technologic Branch of the Geological Survey, James R. Garfield, Secretary of the Interior, obtained the cooperation of the Governments of England, Belgium and Germany in sending Captain Arthur Desborough, Inspector of Explosives in England, Mr. Victor Watteyne, Inspector-General of Mines in Belgium, and Mr. Carl Meissner, Counselor for Mines in Germany, to visit American mines and make recommendations for increasing safety and efficiency in mining coal in the United States.

Jun 1, 1950

By William Cochran

The mineral waste disposal system at the Grace Mine, Morgantown, Pa., was designed to minimize environmental effects while allowing much of the waste from the iron mine, mill, and concentrator to be utilized. Standard cost estimating procedures were used by the Bureau of Mines to determine waste disposal costs. Mill tailings and rock waste disposal costs were estimated at $0.151 and $0.276 per ton, respectively, for the 1965-67 production period. Total waste disposal cost was reduced about $0.015 per ton by utilizing part of the waste as aggregate. The net average cost for disposal of all mineral waste was $0.189 per ton.

Jan 1, 1969

By A. W. Henderson

This investigation was performed to develop chlorination methods for extracting tungsten from scheelite and from an ore concentrate containing a mixture of scheelite and wolframite. On a laboratory scale with proper temperature control using elemental chlorine, over 90 percent extraction of tungsten is achieved. Carbon and sulfur dioxide were studied as reducing agents. The effects of salts such as calcium fluoride and sodium chloride were studied as additives to increase extraction and to reduce impurities in the volatile tungsten chloride product. Sodium chloride reacts with ferric chloride to form a nonvolatile double salt; whereas the chlorides and oxychlorides of tungsten are volatile and consequently condense free of iron. Separation of tungsten from molybdenum from an equal molar mixture was successful by fractionally distilling the oxygen-free chlorides and by selectively condensing the oxychlorides. Yields of 60 and 80 percent, respectively, were achieved for separating the less volatile tungsten chlorides containing less than 0.5 percent molybdenum.

Jan 1, 1965

By Seth C. Schaefer

The Bureau of Mines has determined the standard Gibbs energies (AGf°) of CoS1.035 (cobalt sulfide) and Ni2.515S2 (nickel sulfide) with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, CoS1.035, CoO, S02(g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt, with the overall cell reaction C0S1.035(c) + 1.535 02(g, 0.0114 atm) = CoO(c) + 1.035 S02(g)¬ These results, combined with the best available data for ?Gf° of CoO and S02 from the literature, give the standard Gibbs energy of formation of CoS1.035 for the reaction Co(c) + 0 5175 S2(g) = CoS1.035(c) ?Gf° = -38.890 + 18.87 x 10-3T ± 0.185 kcal/mole (866.0 - 1,104.9 K), where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, N12.515S2, NiO, S02(g, 1 atm)//Zr02//02(g, 0.0122 atm), Pt, with the overall cell reaction Ni2.515S2(c) + 3.2575 02(g, 0.0122 atm) = 2.515 NiO(c) + 2 S02(g). Combination of these results with data for ?Gfo of NiO and S02 from the literature yields the standard Gibbs energy of formation of Ni2.515S2 for the reaction 2.515 Ni(c) + S2(g) = Ni2.S1SS2(c) ?Gf° -65.377 + 24.67 x 10-3T ± 0.541 kcal/mole (968.6 -1,053.7 K).

Jan 1, 1981

By STUART R. BRINKLEY, Ruth F. Brinkley

This same phonomonon of diffraction may be transposed into the X-ray domain. All that is necessary is to reduco, in the samo proportion, the wavo length of the light and the diameter of the particlo; thus, with radi- ations whose wave length is of the ordog of angstroms, the dimensions of the active particles go from 10 to 100 A that 18, the dimensions of col- loidal particlos. The evidence of this fact is shown by the following experimental schomo (fig. 1a): A narrow beam of X-rays passes through a thin layer of a modium containing micelles; the photographic film is placed a few centimeters behind the sample, and a small absorbing screen stops the direct beam in order to prevent its fogging the film. The intersect of the direct beam is surrounded by a narrow spot whose blackness decreases with the distance from the center. We will call this the spot of central diffusion (fig. 1b). The phenomenon, in spite of its relatively reat intensity, has been observed only by a few authors, who have simply given a qualitative description without attempting any quantitative de- ductions. This is due to the fact that observation of this phenonenon is not possible with the apparatus generally used to obtain X-ray diagrams, because the parasite foggings in the vicinity of the incident beam are sufficiently important to hide those produced by the sample. With the monochromator, however, used by us to obtain Debye-Sherer diagrams, this parasitic diffusion can be totally suppressed. In this way our attention was again directed to the spot of central diffraction, and we were led to make a detailed quaititative study of it.. then several papers have been published on this subject. Hosemann, using methods of calculation outlined by us, has extended them to the special case of fibrous substances, Kratky, on the other hand, starts from an entirely different theoretical point of view; ho examines the case, not of scattered particles, but of closely packed particles. 6ince We will now describe the experimental methods, summarize the calcu- lations needed in the elaboration of diagrams, and finally review the first results obtained in the vast domain of these new physical-chomical studies.

Dec 1, 1946

By W. H. Eddy

The Bureau of Mines conducted laboratory batch flotation tests and continuous pilot plant flotation tests on a complex calcareous fluorspar ore from Cave-in-Rock, Ill., to determine the technical feasibility of producing commercial-grade concentrates by the sodium fluoride-calcium lignin sulfonate-fatty acid method of concentrating fluorspar previously developed by the Bureau. The continuous flotation tests, treating about 150 pounds of ore per hour, produced fluorspar concentrates assaying 96.4 percent CaF2; 90 percent of the fluorspar was recovered.

Jan 1, 1967

By Charles R. Harrison

The purpose of this study and resulting development of the training program, "Safety--Let's Make It Happen" was to determine the relation of concepts to the development of desired Health and Safety behavior. After extensive pre-contract study, it was hypothesized that improved acceptance and understanding of the Federal Coal Mine Health and Safety Act of 1969 could possibly contribute to the reduction of accidents. Second, in order for an individual to accept and understand the Act, he or she must have a working knowledge of its purposes and application. Third, acceptance and understanding of the Act, necessary to protect the individual from negligence, was imperative. Fourth, an actual operating company could provide the base in which to test these hypotheses in a meaningful manner and develop this type of training program. Six assumptions were agreed upon before embarking on this study and training program development. (1) In the cognitive process, a concept introduction into an individual's personality may result in a behavior quite different than if he or she had been exposed to a different concept.

Jan 1, 1977

By G. W. Grove, O. V. SIMPSON

During the years 1945, 1946 , 1947 , and up to July 1, 1948, only one death was caused by mine fires in bituminous - coal mines of the United States . The one fatality occurred in an Illinois mine in December 1945, and , therefore, there had been a period of 2-1/2 years in which no deaths occurred as the result of mine fires . Moreover, 1946 was the first year since 1930 in which no deaths occurred from mine fires . This record is markedly better than that of 1944 , when 89 fatalities and great property damage were caused by mine fires in bituminous - coal mines and 16 additional men were killed by an explosion that occurred while they were attempting to seal a mine fire .

Apr 1, 1949

By Elaine Cullen, Launa Mallett, Mike Jenkins, C. M. K. Boldt, Thomas Camm

The material in this Information Circular was presented at the National Institute for Occupational Safety and Health’s (NIOSH) open-industry briefing held during the 2004 Northwest Mining Association conference in Spokane, WA. The open-industry briefing discussed results of recently completed and on-going mine safety- and health-related research conducted at NIOSH’s Spokane and Pittsburgh Research Laboratories on the human side of mining—the miner. The first paper sets the stage for what mining has achieved and what we mean by “getting to zero.” The second paper, “Help Experienced Miners Become Great On-the-Job Trainers,” distinguishes between experienced miners and trainers. This paper provides some key concepts for turning great miners into great trainers. “The Power of Story-Telling in Getting Through to Miners” explains the history and importance of stories in the culture and training of miners. Finally, “Understanding Self in Stressful Working Environments,” describes the personal and social aspects of the working environment, much of which parallels familial theories. The downward trend of deaths in U.S. mining has been remarkable. The number of miners killed or injured each year has decreased steadily over the past 100 years. Some charts show these trends overlain with important events such as World War II and the Mine Safety and Health Act. However, this downward trend in mining fatalities has flattened out. How can you get to zero accidents? Do you concentrate on technological advances and equipment maintenance to avoid malfunctions? Do you concentrate on developing work processes and organizational structures that minimize risk? Do you combine them and take a systems approach that links one to the other with an evaluative loop? Safety efforts in mining have used all of these approaches. What more can we do to get to zero? Getting to zero will require two objectives: A clear and unshakeable belief that it can be done and attention to the human side of mining. Getting to zero is not a new idea; it has been used by mine companies and safety professionals for years as the safety goal. But getting to zero is not so much a physical goal as it is a belief that there are no insurmountable barriers to achieving the goal.

Jan 3, 2006

By S. L. May

Investigations by the Federal Bureau of Mines indicate that hafnium and zirconium compounds of acceptable purity can be extracted from Nigerian zircon concentrates. Chlorination and caustic soda fusion techniques were used to extract 85 to 95 percent of the valuable metals from the concentrate. The extracted hafnium and zirconium compounds were purified by recrystallization of the oxychlorides or by formation of complex salts during chlorination. The zirconium-hafnium product of the recrystallization method contained 15 parts per million of uranium, and the product of the salt-complex method contained less than 10 parts per million of uranium. The hafnium was separated from zirconium by solvent extraction methods. A zirconium product containing 0.3 percent hafnium and a hafnium product containing 4 percent zirconium were obtained. At the request of the Atomic Energy Commission (AEC), work was started to develop techniques for processing Nigerian zircon concentrates in commercial installations presently engaged in producing zirconium and hafnium metals from ores. The Nigerian zircon has a high hafnium content, but the presence of uranium and thorium is a problem not normally encountered in processing zircon concentrates.

Jan 1, 1961