Search Documents

By Mark S. Stagg, Norman S. Smith, Rolfe E. Otterness, Stephen Rholl

Blast design parameters were studied in an attempt to quantify their relationship to rock fragmentation. The Bureau of Mines conducted a series of 29 reduced-scale shots at the University of Missouri-Rolla's experimental mine with bench size from 40 to 80 inches. Design parameters varied were burden, spacing, explosive diameter and stemming-explosive length. The shots had 3 or 4 blastholes fired at delays of 1-4 ms per foot of burden, based on previous tests that showed hole interaction could improve fragmentation by 12 to 20 percent over single-hole shots or simultaneous firing. All rock, 2000 to 23,000 pounds per shot, was screened and weighed to determine the fragmentation size-weight distribution.

Jan 1, 1991

By Jaime Huidobro, Mervin Austin

The effect on an explosive column of the sharp transient stress waves generated during the earlier detonation of adjacent blastholes is of paramount importance to explosives users. Some explosives will sympathetically detonate under these stresses. Others may suffer a transient desensitization, arising from a temporary increase in the density of an explosive beyond certain limits and persisting until the explosive mass relaxes back to the original density. Some explosives are so adversely affected by these stresses that the product suffers immediate and permanent loss of sensitivity. These effects can be clearly seen while blasting in tough conditions such as burn cuts or wedge cuts and in materials, such as coals, that propagate shock waves well.

Jan 1, 1992

By Dennis Alan Clark

An increase in construction and quarry operations has necessitated blasting activities in areas once considered rural and in the close proximity of transmission pipelines. A method to determine the maximum allowable bending stress by the formulas outlined by the Battelle Memorial Institute report of October, 1962, and the assumed stress comparison with actual measured data is presented. A direct relationship between pipe stress and ground particle velocity is shown, and a method to predict stress by relating stress to charge weight and distance from the shot point is discussed.

Jan 1, 1976

There is an intuitive tendency to equate rock strength with rock stability, yet the two must be evaluated separately. A slope in strong hard rock is not necessarily stable, nor is a slope in weathered weak rock necessarily unstable. In some cases the reverse is true, depending on the geometry of joints and weak planes. The time element is a matter of special concern, that is how suddenly the failure begins and how rapidly it progresses. Sudden failures can be catastrophic, whereas creep usually is not. In soils and weathered rock, the process is usually incremental and is more likely to give some warning of impending failure. With careful observation, the failure process in these materials can be detected and monitored instrumentally or visually. In some cases, the slope may be stabilized, reinforced or modified. When that is not possible, there is usually enough time on this type of slope to remove men and equipment from the area before complete failure occurs.

Jan 1, 1996

By Brian Stump, D. Craig Pearson

This work quantifies seismic coupling as a function of charge weight for single-fired (simultaneously detonated) explosions observed in the mine and at regional distances. These single-fired explosions are contrasted to standard production shots from the same mine. Production shots include cast blasts to remove overburden and coal shots for fragmentation. The blasts were conducted in a mine in NE Wyoming. The data sets consist of measurements in the mine (100-10,000 m) and at regional distance (360 km) using a seismic array near Pinedale, Wyoming (PDAR). The single-fired explosions ranged in designed size from 5,500 to 50,000 lbs. Peak amplitudes measured at a single element of the regional array are modeled by a power law relation dependent on explosive weight. Scaling constants were determined for each of the dominant regional phases: b(Pn) = 0.84±0.14; b(Pg) = 0.84±0.09; b(Lg) = 0.91±.08. Spectral ratios of observations from different explosions observed at the same station illustrate the frequency dependnce of the source scaling relations. Spectral ratios of in-mine observations are consistent with those of regional data. The observed single-fired ratios are well replicated by Mueller-Murphy source model ratios. The data and model illustrate both the increase in long-period spectral level and the accompanying decrease in source corner frequency with increasing charge weight. The coal and cast blasts that make up the production shots ranged in size from 77,000 to 4,738,230 lbs. The peak amplitude (1-20 Hz) for the largest delay-fired production shot (4,738,230 lbs.) is comparable to that of the largest single-fired explosion (50,000 lbs.). This comparison can be explained in terms of destructive interference between waveforms from individual boreholes introduced by delay firing. Shot specific models of delay firing suggest that peak amplitudes in this same frequency band for the production shots are insensitive to the total amount of explosives in the blast. Peak amplitude data at regional distances supports his modeling result.

Jan 1, 2002

By Virgil J. Stachura, Larry R. Fletcher

The Bureau of Mines conducted a series of delayed blasting experiments at a West Virginia contour coal mine which resulted in smoother highwalls. The highwalls were smoother due to reduced overbreak and inherently safer due to reduced likelihood of rockfall. Reduced overbreak was accomplished by an increase in the highwall hole delay intervals which changed the effective delay pattern geometry and the direction of burden movement. Three combinations of blast delay intervals in the highwall holes were tested: 1) 50 ms longer than the nominal design, 2) 50- and 100-ms longer delays in the nearest two rows that form the highwall, and 3) 100 ms longer than the nominal design. The mine's nominal blast design was a flat vee formed by 17-ms surface delays between holes and 42-ms surface delays between rows, with 200-ms in-the-hole delays. All three test designs produced highwall improvements over the nominal design with only occasional exceptions because of geologic variations.

Jan 1, 1985

By Richard J. Mainiero, Michael S. Wieland, Harry C. Verakis

The Bureau of Mines, U.S. Department of the Interior, has been conducting research on delay blasting in underground coal mines in support of the efforts of Mine Safety and Health Administration (MSHA), U.S. Department of Labor, to revise coal mine blasting regulations. Part of the research centered on developing an understanding of the factors that lead to misfires of permissible explosives. Research was conducted to determine whether frequency of misfires was related to borehole spacing. For a wide variety of permissible explosives, misfires were observed for about 50 X of the holes at 45-cm (18-in) spacing. Misfires were also observed for 60-cm (24-in) spacing, but the frequency of misfires was much lower than observed for the 45-cm (18-in) spacing. The Bureau has recommended that hole spacings of less than 60 cm (24 in) be prohibited.

Jan 1, 1986

By Richard J. Mainiero, T S. Bajpayee

The Bureau of Mines, U.S. Department of the Interior, has developed test procedures and criteria for evaluating explosive reactivity of explosive contaminated solid waste substances generated by U.S. Army Ammunition Plants. These substances are produced as explosive-contaminated sludge from waste water treatment plants, residues from the burning of munitions and explosives on open ground, and residues from deactivation furnaces. The characterization of explosive reactivity is a prerequisite for disposal of such waste materials, which may be contaminated with primary explosives, propellants, or pyrotechnic materials. The Bureau has proposed two tests for this purpose. These tests were developed to evaluate the explosive reactivity as defined in Title 40, Code of Federal Regulations, Part 261.23(a)(6) and (7). These are Bureau of Mines Gap and Bureau of Mines Internal Ignition tests, which determine the sensitivity to shock and thermal stimuli, respectively. This paper also includes gap and internal ignition reference data for typical blasting agents, high explosives, propellants, and marginally reactive substances. These reference data were used to establish test criteria. The Bureau has evaluated over 400 samples of contaminated soil, sludge, and burning residues using these two test methods.

Jan 1, 1988

By Navid Mojtabai, Jaak J. K Daemen

Some facilities require ground vibration limits that are far below typical vibration levels of interest in most blasting situations. A possibly extreme example of such a facility might be the proposed SSC (Supercollider Super Conductor) high energy particle study system. The applicability of conventional blast vibration predictors for such a low amplitude vibration is highly uncertain. For this preliminary study, a series of field measurements are made, and the results integrated in a set of vibration predictor equations. Ground vibrations induced by blasting operations at one proposed SSC site are monitored at close distances (hundreds of feet), intermediate distances (miles), and long distances (tens of miles) from the blasts. Peak particle velocities are recorded at short distances, ground displacements at other points, as well as frequencies. Theoretical analyses are performed by integrating all data in a variety of ground vibration predictors. From the statistical analysis of the data, ground motions at various points along the ring site are predicted for a given charge weight. The approach taken appears adequate for making tentative estimates of exceedingly low amplitude vibrations at great distances from mine blasts.

Jan 1, 1987

By D VanDoorselaere

"Image analysis techniques are widely used for blast fragmentation measurement, and various commercial packages are available for this purpose. These packages are very versatile and serve as a useful tool for optimization of blasting practice. But many times, the results provided by image analysis techniques do not match with sieved and predicted data. This leads to the suggestion that understanding the limitations of this technology is as important as understanding its usefulness and versatility.A study was conducted in two stages:(a) Comparison between the results of image analysis and screened data using laboratory scale muck piles.(b) Comparison between predicted (Kuz-Ram) and measured (Image analysis) blast fragmentation results for several bench blasts.During laboratory work, muck piles with known size distributions were analyzed with the help of image analysis technique. A disparity was observed between the sieved and measured results because the image analysis techniques cannot accurately determine the % of fi nes in the muck. During fi eld work about fourteen blasts were monitored. It was observed that predicted (Kuz-Ram) results rarely matched with measured (Image analysis) results. The Kuz-Ram curves were modifi ed by changing the rock factor so that the Kuz-Ram and Image analysis curves match in the vicinity of the 50% passing size. The pairs of curves (modifi ed Kuz-Ram and Image analysis) were divided into three categories depending upon their differences in the coarse and fi nes ranges. The blast design parameters affecting the difference between the pair of curves have been outlined. The suggestions have been made to better utilize the image analysis system."

Jan 1, 2007

By Peter Cameron, Tom BoBo

Comminution, being the energy intensive part of a mining operation receives much scrutiny by cost controllers, CEO’s, investors and others as the mining industry goes “back to basics” to reverse the decline in productivity which occurred during the mining super cycle.

Jan 1, 2019

By Yoshihiro Moriyama, Toshihiro Okitsu, Ryouichi Banno

The fracturing composition using the gas pressure generated by the thermit decomposition reaction gives the following performances.

Jan 1, 1995

By Sushil Bhandari

Presented here is the simplified process of fragmentation of homogeneous rocks by blasting based on experimental studies. Small scale single hole blasting experiments on jointed limestone are described. Results show that directions of joints overshadow the degree of fragmentation and also influence the remaining rock. The possible influence of joints on the process of fragmentation of non-homogeneous rock by blasting is also discussed.

Jan 1, 1983

By A. Cobbii, M. Kasliki, W. Birchi

The Department of Mining and Mineral Engineering at the University of Leeds has a long history of research into the environmental impacts of blasting from quarries and opencast mines. This paper gives an outline of a detailed case study into the structural damaged induced in a rock walled tunnel with a brick lined crown due to close proximity quarry blasting. The test site Taffs Well Quarry is located in South Wales in The United Kingdom and has a disused railway tunnel situated within the south eastern comer of the quarry site. Quarry development plans included the working of this area and therefore the deliberate destruction of the central section of the tunnel.

Jan 1, 2001

By Dwayne Tannant, Jeffrey Loeb

Blasting techniques and protective measures exist that can mitigate risks associated with flyrock and the nuisance of vibration, and overpressure. However, these are often misused or not used because there are no prescriptive regulatory requirements and typically urban blasting guidelines do not exist. The relationship between the increasingly negative publicity that the urban blasting industry receives and the existing state of regulatory control on blasting in urban environments is presented.

Jan 1, 2012

By George Young Mosteller

This paper is summary of the practical solutions developed in the excavation of drilled piers (caissons) at GPCo's Plant Scherer, Juliette, GA. Plant Scherer is a 3,245 Megawatt Fossil Fuel Powerhouse and, when completed, will be one of the largest fossil fuel plants in the Southeast.

Jan 1, 1980

By R A. Farnfield

Measurement of the environmental impact of ground vibration from blasting operations is based almost exclusively on the peak vibration level generated. This measurement is known as the Peak Particle Velocity or PPV. The recorded PPV is used to assess the impact of the vibration both in terms of structural damage and human response. Limits for vibration are almost universally quoted in terms of PPV levels and, as a consequence, blast design for vibration control is centred around techniques for the control of this peak value.

Jan 1, 1996

By S Lukovic, Vishwa Bhushan, Calvin J. Konya

Effect of each of these variables has been well characterized for ANFO. This paper presents results of underwater energy measurements for one watergel and one emulsion type of slurry explosive which were initiated by 3 types of initiators (one electric and two cords of different strength) in 2 and 3 inch diameter steel pipes. Results of this 2 x 3 x 2 factorial experiment show the effects of detonating cord on energy released by the watergel and the emulsion explosive. Effect of diameter and its interaction with cord strength have also been characterized for the two explosives.

Jan 1, 1986

By Donald D. Eilers, Pharis E. Williams, Thomas O. McKnown

The Continuous Reflectometry for Radius vs. Time Experiment (CORRTEX) system was developed by the Los Alamos National Laboratory for determining the energy released in a nuclear explosion by measuring the position of its shock front as a function of time. The CORRTEX system, fielding techniques, and the methods and software for data reduction and analysis were developed over a 15 year period with hundreds of measurements made on nuclear tests and high explosive experiments. CORRTEX is a compact, portable, fast-sampling, microprocessor-controlled system, based on time domain reflectometry, requiring only a 24 volt power source and a sensing element. Only the sensing element (a length of 50 ohm coaxial cable) is expended during the detonation.

Jan 1, 1995

By Brian W. Stump

The cessation of testing of any nuclear explosive devices in all environments is the goal of the Comprehensive Test Ban Treaty. In order to assure compliance with such a treaty, an international monitoring system has been proposed. This system will include seismic, infrasound, hydroacoustic and radionucleide monitors located throughout the world. The goal of this system is the detection of any nuclear test. In preparation for this treaty, a series of monitoring system tests, focusing primarily on seismic observations, have been undertaken. The most recent of these tests, Group of Scientific Experts Technical Test Three (GSETT-3), provides valuable data for assessing future monitoring systems. During the course of this experiment, seismic events associated with earthquakes, nuclear explosions and mining explosions have been recorded. This presentation will discuss the numbers and types of mining explosions triggering the system, in a particular area. Possible implications for the mining industry will be explored.

Jan 1, 1997