Search Documents

By Cristian Castro, Patricio Gomez, Jason Furtney, Augusto Lucarelli

Understanding the effect of blast-induced damage on wall stability is critical to safe and economical operation of a large open pit mine. In this paper, a numerical modeling methodology is used to investigate damage to rock at distances of greater than 10 m (30 ft) from a blast. Two applications of the model are demonstrated. First, the method is applied at a zinc mine to investigate the effects of pit blasting on underground stopes. The model predictions are compared with the scaled distance formula. Next, the model is used to investigate a common problem in which unfavorable jointing creates a rock wedge on the bench above a blast. The numerical predictions of wedge stability are compared to the wedge energy model described by Wong & Pang (1992).

Feb 1, 2020

By Jonathan Heiner

Rio Tinto Bingham Canyon Mine started its South Wall Push Back (SPB) in 2011. This push back will mine through the only road to the pit bottom (the 10%). The pit bottom is the main ore sector for the mine and supplies about 80 to 90% of the ore. In late 2017 the mine set off a blast in SPB that created a small wedge failure on the high wall between SPB and the 10%. This wedge failure released a rock approximately 20 minutes after that blast that rolled down the wall landing on the 10% near and then contacting a light vehicle

Jan 1, 2019

By Jose A. Sanchidrián, Ricardo Castedo, Pablo Segarra, Juan Navarro

A study conducted at a mine site that used traditional field surveying and physical hole spot markings bench marked their combined drill and blast performance. The analysis of the operational expenditure (OPEX) improvement determined there were many measurable cost improvements. A primary factor that most operations have to deal with is over drilling of holes. This alone impacts the cost due to nonproductive labor allocations, excessive explosive costs, increased drill tool costs, increased drilling costs and has an impact on the downstream operation cost such as digging the shot material. Other related investigations also show a downstream impact of poor fragmentation on digging payload tonnes, cycle times, haulage payload tonnes, time to load a truck and the number of passes to load the tuck. The intent of this presentation is to draw attention to aspects of mining we understand but may be missing the big picture effects, such as the ability to reduce the operational expenditures consistently to impact the bottom line. The target audience is across the board from owner operators, drill and blast contractors to blasting contractors. Everyone can benefit from these improvements.

Jan 1, 2019

By Nicholas Matthews, Vilem Petr

This project will report findings on the establishment of a new surface test site at the Colorado School of Mines Edgar Mine. Concerns over the blast effects on site neighbors prompted the study to be conducted. The current maximum charge weight of 20-lb was studied to ensure that all environmental effects were within the range prescribed by state and federal regulations. Geophone locations were surveyed using GPS and monitored using Instantel Minimate Plus instruments. Distances and orientation of measurement sites to the test site were varied according to the local geography and geology. Weather conditions were also observed and recorded during all tests. Neighbor complaints were recorded and taken into account during analysis. Current results show that the current charge limit results in a safety factor of over 200 for all blasting activities at the site. Data collection is ongoing and a review is to be conducted annually. These results will be presented in the future. Results are presented and discussed in the following paper. Copyright

Jan 1, 2010

By Kfw Eick

The paper describes the use of the Nonel millisecond delay blasting system in narrow, deep, tabular ore bodies and briefly describes the standard stoping method as used on Harmony Gold Mine and compares this with the new Nonel short panel system.

Jan 1, 1990

By Clayton Thompson

Linear detonation wave generators (DWGs) shape a detonation wave so that every portion of the wavefront reaches the target “line” simultaneously. A projection-type linear DWG uses Gurney plate velocity predictions and Taylor deflection angle predictions to estimate the angle at which a thin projected flyer (typically metal) will impact a target. A mousetrap-style planar DWG consists of two projection-type linear DWGs working in succession to create a planar wave-front through shock initiation of each successive target explosive. The angle of deflection is critical to yielding a planar or linear wave profile. Gurney predictions, nominally accurate to within 10% of empirical results, may not yield ideal linear or planar detonation behavior when used with a grazing projection-type DWG, which typically requires accuracy within 2%. Simulations were conducted using AUTODYN hydro code to compare deflection angle prediction methods. Ranges of minimal error between Gurney and Taylor predictions and the results from the hydro code were determined, using PBX-9404-driven polyethylene flyers.

Jan 1, 2011

By Timothy D. Stark

Blasters are usually strictly liable for injury or damage caused by flyrock (trespassory invasion) and blast-induced vibrations (non-trespassory invasion). The application of strict liability to non-trespassory invasions has resulted in significant litigation that has hampered the use of blasting and the blasting industry. Stark (2002) proposes that blasters should not be held strictly liable for non-trespassory invasions but should be liable only if their conduct is proven to be negligent. This change in legal standard was proposed because improvements in blasting technology over the last thirty years allow blasting to be conducted without substantial risk of harm to property and thus the amount of harm imposed by a blast can be related to the level of care exercised by the blaster. It is anticipated that negligence standard will reduce the amount of litigation because a plaintiff will have a greater burden to overcome. To facilitate the acceptance of negligence standard by a court of law, this paper illustrates the application of the negligence and strict tort liability frameworks using actual cases in which a decision was rendered. It is evident from these cases that some of the successful claims under the strict liability framework would not have been successful, and probably not litigated, under a negligence framework, which could result in substantial cost savings to the blasting industry and consumers.

Jan 1, 2004

By Manuel Calderón

Chile is responsible for 30% of the global copper production; the world ́s largest. However, significant challenges are faced in this industry; declining grades (1.13% in 2002 to 0.61% in 2015), high cost of energy, scarcity of water, and environmental concerns. Mining trends suggest the future of the industry will be focused in the underground space, specifically due to the depletion of economically viable surface mineral deposits. For example, the largest block cave mineat Codelco ́s Chuquicamata mine is expected to reduce energy costs by 50% and dust emissions by 97%compared to the open cut mine. To access these underground deposits, critical infrastructure is required; horizontal tunnel developments, extraction levels, vertical raises, and ore passes with the on-time delivery of the highest quality outcomes being a requisite for successful project delivery (Lift 1 of 3 at Chuquicamata Underground has over 1000drawbells).One aspect that makes this scenario even more challenging for deeper underground operations is the increased risk profile (people, equipment, and geotechnical) that forms part of the general environment. Furthermore geotechnical risks should be considered and they include rock burst and windblast. The safe interaction with this environment must be sustainable throughout the full life of the project. This paper presents the Enaex group approach to addressing the blasting challenges and outlines the solutions created. Aspects such as rock mass damage occurrence as a function of blast vibration frequency content has been studied, as well as the development of blasting methodologies for guaranteeing the full 100% extraction of all infrastructure blasts, including the all-important draw bell volumes. The development of such infrastructure volumes in one single event using electronic detonators and the associated achievement of ambitious productivity goals, are described as a critical part of the successful construction of one of the most ambitious UG projects currently present on the world.

By Manuel Villalobos Calderón

This paper presents the Enaex group approach to addressing the blasting challenges and outlines the solutions created. Aspects such as rock mass damage occurrence as a function of blast vibration frequency content has been studied, as well as the development of blasting methodologies for guaranteeing the full 100% extraction of all infrastructure blasts, including the all-important drawbell volumes. The development of such infrastructure volumes in one single event using electronic detonators and the associated achievement of ambitious productivity goals, are described as a critical part of the successful construction of one of the most ambitious UG projects currently present on the world.

Feb 1, 2020

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling.

Feb 1, 2020

By Frank Hirthammer

Since the introduction of the Explosives Track & Trace in Europe in 2014 for manufacturers and 2015 for end-users, a lot has changed in all areas of the supply chain and the use of explosives. The regional associations, manufacturers' organizations, and trade associations have proven that it is possible to overcome a hurdle, that looks almost impossible in the beginning, through consistent cooperation. The paper gives an insight into the problems involved in introducing such a requirement, identifies ways and solutions, and concludes them. When looking at the current situation, the paper describes the process by which a prescribed change in business processes are transforming into a solution that increases productivity, security, and handling. It shows examples from daily work, in which possibilities for optimization, improved quality assurance, and work facilitation are explained. It presents the resulting potential by comparing process flows, before and after the introduction of Track & Trace solutions. What challenges will we face in the future concerning the use of T&T solutions? Will the tracking of explosives become the norm worldwide? What are future hardware and software developments to be expected? What impact will this have on the global supply chain?

By W. Birch, G. D. Rangel-Sharp, L. Bermingham

For many years, the accepted method of Measuring the Velocity of Detonation (VOD) in blast holes has been to use an electric cable of a constant resistance per metre. Thus as the wire is consumed by the explosive in the blast hole, the change in resistance is monitored and when this data is plotted against the time period of the in hole explosion, the VOD can be calculated.

Jan 1, 2011

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By Jose Pineda, Abraham Lindo

The Panama Metro System’s Network expansion involves excavating a launching shaft for a tunnel boring machine (TBM) to traverse beneath the Panama Canal. The blasting needed for this shaft construction poses significant challenges due to the presence of concrete walls encircling the excavation. These walls must remain intact throughout construction and the tunnel's future operation. This case study is focused on devising and implementing safe blasting techniques crucial for the shaft's construction, ensuring the preservation of surrounding concrete walls and project equipment. As the interest was potential damage to the concrete walls, an appropriate vibration threshold for this project was also required as an alternative to the traditional U.S. Bureau of Mining RI-8507 limit (USBM RI8507). Blast modeling software was employed to conduct a series of blasting simulations. Parameters like hole diameter, spacing, depth, explosive type, and initiation methods were varied to evaluate their potential effects on wall stability and damage risk. The simulations revealed that smaller diameter holes and reduced spacing between blast holes would effectively mitigate the risk of wall instability. Additionally, utilizing electronic delay detonators and carefully planning the blast hole detonation sequence proved critical in minimizing potential damage. Executing these blasts in the field presented unique challenges, including strict charge per delay thresholds and logistical constraints. Consequently, continuous adjustments to blasting parameters were made and comparative result analysis. Beyond providing a safe blasting strategy for the TBM launching shaft, this study offers invaluable insights into adapting blasting designs to align with environmental and structural safety standards. These findings hold great potential to shape guidelines for analogous sensitive construction projects. They underscore the importance of leveraging prior research as a reference point, engaging with project designers and local authorities, and continually conducting testing and adjustments to ensure project success.

Jan 21, 2025

By C James Dahn

A new generation of high performance and high density ammonium nitrate prills have been developed. These cycled "prills" offer significant improvement in ANFO mixing time, detonation velocity performance, and heaving capabilities. In addition, their safety characteristics are better than standard ANFO explosives.

Jan 1, 1980

By Peter Moser, Michael Messner, Florian Bauer

The existence of ammonia in underground blasting fumes was frequently measured in various field tests (6, 7). Ammonia in fumes with a TLV (threshold limit value) of around 30 ppm (slightly different in various countries) is a toxic gas but not considered to be a high risk for the underground work force as ammonia smells very itching and is extremely annoying. This might be the reason why ammonia is hardly measured in routine underground blasting fumes control. Another reason for the lacking measurement might be the circumstance that ammonia is a very reactive gas and the ammonia sensors available on the market are very cross sensitive to other gases like carbon monoxide. Nevertheless, especially since the introduction of bulk emulsion explosives in underground blasting, complaints from miners about ammonia in the blasting fumes increased. Research work by various institutions [8] around the world relates the ammonia in the fumes back to various mechanisms. Amongst others these comprise: a) non ideal (low temperature) detonation of explosives, with NH3 in the reaction products; b) reaction between rock and non detonated bulk explosives (especially when the rock is of a basic nature (high pH value); c) reaction between shotcrete and non detonated bulk explosives. Numerous blasting tests in an experimental underground set up have been made in order to check these hypotheses for ammonia origin in blasting fumes. None of them has been found to be responsible for sometimes high concentrations of ammonia in the fumes. The major reason for ammonia concentration in blasting fumes has been found in mine water of a high pH value (either natural or from using shotcrete). The mechanism identified is as follows: the moment a non detonated ammonium nitrate bearing explosive comes in contact with mine water of a high pH value, ammonia is formed immediately. The source for the undetonated explosive is twofold: firstly there is a certain spillage of explosives when the holes are charged (especially when using bulk products) and secondly not the entire explosives detonate completely. These undetonated remaining of the explosives end up in the muck pile after blasting. In case there is water of a high pH value the reaction between the explosives and the water starts immediately. This explains also the observation why ammonia can be measured in the blasting fumes quite a long time after the blast. The majority of the ammonia is not formed during the detonation; it is formed inside the muck pile even a considerable long time after the blast.

Jan 1, 2010

By Tristan Worsey

This work was performed during the summer of 2008 during the junior year of a BS in Mining Engineering. It was observed that the mine was having a problem with back break during the blasting of development drifts. The unwanted back break was causing the mine extra costs in ventilation, ore dilution, ground support, back fill, explosives and man-hours. The blasting practices were observed for four weeks and the problems and their solutions were defined. In this paper the reasons and causes of the problem are explained with the proposed solutions to eliminate back break.

Jan 1, 2010

By A K. Raina, P B. Chourdhury

Flyrock is the unwanted throw of rock fragments to excessive distances in opencast blasting. The incidence is relative in nature incorporating the distance of objects of concern like structures within and outside the mine, equipment within the mine & near the blast and persons within and off the mine. Several attempts to predict and defi ne fl yrock made worldwide could not address the problem since the phenomenon is not a regular feature in blasting. This probabilistic nature of fl yrock allows for risk calculation. CIMFR, India developed a Factor of Safety based risk criterion (10, 14) for evaluation of throw/ fl yrock in opencast mines that incorporates all the above in terms of distance and allowable limit of throw – which in turn determines the risk. The criterion provides the blaster a tool for mathematical evaluation of fl yrock risk in terms of a Factor of Safety and threat ratio (defi ned for the 1st time), thereby enhancing confidence when blasting. The method is easy to use and has been applied to several mines in India and the results are signifi cant. This paper details the evolution of the concept and its application in three limestone mines of India and the results obtained. The application of the method for defi ning a fl exible danger zone is also discussed.

Jan 1, 2008

By Türker Hüdaverdi, Özge Akyildiz

"Efficiency of blast operations depends on fragmentation, overbreak, muckpile profile anddisplacement, vibration, airblast, flyrock and damage to wall or slope stability. To provide all these conditions at the optimal level, determination of rock mass properties (in-situ block size, joint spacing and orientation) is the very first step during design stage of rock blasting. Image analysis software is used not only to determine the fragmentation level of muckpile but also to characterize the bench face. In this study, an image analysis software was used to determine apparent block size of bench face and to measure blast fragmentation of muckpile. The source of errors and the vital points to be taken into consideration were explained for bench face characterization andfragmentation measurement. Since it provides much better results than previous techniques and it is not intrusive to production process, image analysis technique is considered as one of the most efficient and preferred way for fragmentation analysis. Besides these advantages, there are some weak points of image analysis software. Lighting is one of the most important factors for photographs captured for in-situ block size analysis and fragmentation analysis. Lighting determines shadow formation. In an ideal image, particles are clearly delineated by soft shadows. If shadows are too strong (dark), analysis suffers. Appropriate scale should be replaced onto blast muckpile during site measurements. The location of the scale in image affects the results of analysis. Also, the densityand orientation of discontinuities should be considered during application of image analysis technique to characterize bench faces. In this study, image analysis software was applied in thesandstone, limestone quarries of Istanbul region and an open pit boron mine. All image analysis, evaluations and results were made based on the site measurements."

Jan 1, 2017

By Roger Keller, Jason Ryan

A number of studies have evaluated excavation methods for the construction of subsurface facilities for a potential deep geologic repository for the disposal of nuclear waste at Yucca Mountain, NV. Many of these studies suggest that where TBM (tunnel boring machine) methods are not applicable and alternative mechanical excavation methods can not efficiently excavate harder rock drill and blast methods may be the most efficient means of excavation. However, a number of concerns regarding drill and blast applications have been raised in these evaluations, most notably the affects of blasting on the surrounding perimeter, as isolation of the waste by the natural barrier of the surrounding rock is a key element in the concept of a deep geologic repository.

Jan 1, 2001