Search Documents

By D. Dreher Whetstone, Paul M. Blakita, Christopher M. Reith, Ravi P. Malviya

"Micro-piles are small diameter (5 to 10 inches), cast-in-place piles which can develop high load capacities by bonding with soil or rock. Micro-piles are particularly well-suited for moderate to heavily loaded structures requiring deep foundations in difficult subsurface conditions, such as karst, bouldery mine spoil, or unsuitable fills with concrete debris or other obstructions. Attempts to install conventional deep foundations including driven piles, drilled piers, or auger-cast piles are likely to be fraught with construction difficulties and disputes, delays, cost overruns, and may be unfeasible in some cases. Micro-pile installation equipment is very effective in installing foundations through such overburden or rock materials.This paper presents case histories of Micro-pile installations on two projects with difficult soil/rock materials. The project sites are located in Charles Town, West Virginia and Masontown, Pennsylvania.Charles Town, West Virginia ProjectThe Charles Town project entailed construction of a four-story pre-cast concrete garage. Triad Engineering, Inc. performed a geotechnical investigation for this project (Triad, 2001). The subsurface, geologic, and project specific information described in th is paper are largely based on the aforementioned geotechnical report.Ground ConditionsThe project site is located in Jefferson County, West Virginia, and is mapped to be underlain by the Elbrook Formation. This formation is described as argillaceous, dolomitic limestone with beds of dolomite and aphanitic and algal limestone (Dean, et al. , 1990). The carbonate rocks at the site were characterized as ""moderately solution-prone, highly calcareous and weathers differentially to produce a pinnacled or ""sawtooth"" top of rock profile. (Triad, 2001 )"" Overburden soils consist of low to high plasticity, fine grained residual soils formed by weathering of the parent carbonate rock. The residual soils include variable proportion of sand and rock fragments."

Jan 1, 2005

By John Y. L Chen

This paper presents full-scale instrumented pile static compressive and tensile load tests to be conducted in the area of Pearl Harbor, Hawaii. Thousands of piles have been installed to support the existing piers and wharves in the Pearl Harbor area. Due to the absence of bedrock within practical depths, most of the piles use combined friction and end bearing. A new 925 feet (282 meters) long and 50 feet (12 meters) wide reinforced concrete wharf supported on pile foundation is planned. This paper will present results of soil investigation, laboratory testing, dynamic load tests during indictor pile driving and static pile load tests. The subsurface conditions consist of soft harbor sediment, young alluvium deposit, volcanic tuff rock formation and stiff old alluvium deposit. The load test piles consist of 20-inch (508 mm) square and 24-inch (610 mm) octagonal pre-stressed, pre-cast concrete pile and instrumented with embedded strain gauges. The length of the piles ranges from about 50 to 125 feet (15 to 38 meters). The test pile program consists of probing, driving indictor piles, dynamic load tests during indictor pile driving and static load tests. The standard loading procedure method was used during static pile load tests.

Jan 1, 2002

By Alan Quiroga

Nestled between Meridian Park and Howard University in the heart of Washington, D.C., the historic block between 14th, V and W streets North- west featured several original struc- tures, many of them dating to the 1800s. During its rich history, this square block has been home to a variety of different organizations including automobile showrooms and repair businesses, a parking garage, various industrial warehouses, and, in recent years, the headquarters of the renowned D.C. nonprofit Martha's Table. The revitalization of the buildings in this block also known as the Collection 14 project involved the transformation of aging and historical structures into a new multi-use development. The redevelopment project was distinguished by the retention of period street-facing building facades (to the extent possible) to preserve the character and culture of the historic neighborhood while revitalizing the block with some modern construction elements. The complexity of the project and difficult subsurface conditions required specialized and extensive sheeting, shoring and underpinning work to be performed. This project had many parties involved, including: • • • • Owner: Madison Investments Owner's representative: Compass Design & Development General contractor: McCullough Construction Civil engineer: Vika Capitol Structural engineer: Ehlert Bryan Architect: Perkins Eastman DC Geotechnical engineer: GEI Consultants Sheeting and shoring contractor: Steele Foundation

Aug 1, 2023

By Pierre Gouvin

"This paper discusses real time monitoring of utility vaults during the reconstruction of the Elliot Bay Seawall in Seattle. The project, undertaken because deterioration of the old wall posed increasing risks to property and lives, impacts businesses, ferry terminals, a rail line, and electrical utilities that distribute power to much of the downtown area. The project, which has been fast tracked to minimize risk and commercial impacts, involves multiple contractors with heavy machinery working in an area one mile long and only a few hundred feet wide. This presented challenges to monitoring of the utilities, as will be discussed in the paper.INTRODUCTIONThe Elliot Bay Seawall (EBSW) was built in over a period of 18 years, starting in 1916. It consisted of a vertical concrete wall placed on a timber pilings and timber relieving platform. The seawall also retained fill that served as the foundation for a road known as the Alaskan Way. The seawall has performed well over the years, but now cracks in the concrete have allowed loss of fill, and the timber piles and support structures have been weakened by marine boring insects.The project to replace the seawall was undertaken because deterioration of the old wall posed increasing risks to property and lives. Because the project impacts businesses, tourism, ferry terminals, and a rail line, it was given a compressed timeline - 36 months from start to finish. In addition, construction activities have been staged carefully to minimize disruption of Salmon and other wildlife living in Puget Sound. In fact, will incorporate several habitat improvements to promote sea life, such as a nature-imitating textures in the surface of the wall and a glass deck structure that allows sunlight to reach the water. (Fig. 1) shows a schematic of the planned new wall.The sheet piling, concrete piles, jet grouting, drilled shafts, ground freezing, and demolition activities are all taking place in the narrow corridor that holds the subsurface ducts and vaults protecting Seattle’s electrical power distribution. If the network of duct bank and vaults were to experience differential settlement during work here, then most of downtown Seattle would be in the dark. Thus it was important to provide real-time displacement monitoring of these utility structures."

Jan 1, 2017

By V. Tang

In this paper, Chinese economic situation are estimated and prospective developments predicted to assist those US firms who have been trying to do business in China, or are considering to pursue the China market.

Jan 1, 2010

By David White

When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100? of water are well known, let alone in the open waters of the South China Sea. In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130? long, 72? diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE?s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.

By David White

"When finished (projected completion in 2016) the Hong Kong-Zhuhai-Macau Bridge Project will comprise three cable-stayed span bridges and a 4.15 mile immersed tube tunnel - linking Hong Kong to Macau and the mainland Chinese city of Zhuhai. The design included two artificial Islands to serve as the transition structures for the tunnel to bridges, entailing a massive seaborne land reclamation project, and the use of thousands of sheet piles, and man-hours. The challenges of driving individual steel sheet in 100’ of water are well known, let alone in the open waters of the South China Sea.In 2010 a joint effort between American Piledriving Equipment (APE) and Allnamics Pile Testing Experts convinced the Chinese contractor First Harbor Marine Group China that a massive multi-vibro hammer can be used to drive 130’ long, 72’ diameter steel pipe piles weighing 662 US tons each into the sea bed of the South China Sea for the Hong Kong - Zhuhai - Macau bridge artificial islands. Combining APE’s hammer design, production and operation know-how with the pile driving simulation and installation know-how of Allnamics made it possible to show the feasibility of driving these gigantic piles into bottom of the sea to the required depth.INTRODUCTIONThe challenges of driving individual steel sheets in deep water are well known, let alone in the open waters of the South China Sea. Often the challenges of construction are overcome with engineering or equipment. The challenges of China’s Hong Kong-Zhuhai-Macau Bridge, on the drawing board since 1983, were to overcome both. The challenges of overcoming the skepticism of the Chinese Engineering community would be another story.The finished project will comprise three cablestayed span bridges and a 4.15 mile immersed tube tunnel linking Hong Kong on an eastern span to the China mainland cities of Zhuhai and Macau via two western spans."

Jan 1, 2017

By John Davie

We used a Remtek survey in Glenrock and had very good luck with it when we first started the initial investigation. We would have loved to have used that more but my understanding is the equipment is hard to find. It also requires a flooded mine workings. If you're in a dry mine the communication between the two holes is not quite as successful.

Feb 10, 2003

By Dean Abbondanza

"Below grade foundation design has construction issues that above grade foundations do not. These cost factors are dependent on soil conditions and vary by region, but for the most part, the process remains standard.An innovative design concept using steel sheet piles as the permanent wall element changes the traditional cost and schedule for below grade foundations. The sheet pile application reduces dewatering requirements, does not require waterproofing on the vertical walls and eliminates the cast in place concrete wall structure.Foremost, this versatile application affords both Contractor and Designer the choice of two methods of construction; conventional bottom up or top down. The top down method not only provides the savings of bottom up, but also eliminates the cost of anchors while taking the foundation out of the critical path in the early stages of construction. CONVENTIONAL FOUNDATIONSINTRODUCTIONUS construction for a conventional below grade (BG) foundation is fairly standard. Design and install the shoring system, followed by dewatering (if groundwater is present), then excavate in stages with installation of anchorage as work proceeds to final elevation. The site is graded for a waterproofing system to be placed at the base. Once the base slab is cast; forms are set for the vertical reinforced walls. After curing , waterproofing is applied to the back side. The remaining levels are constructed until ground elevation is reached. The site is backfilled and the ground floor is cast. The foundation is now complete and work on the superstructure can now begin."

Jan 1, 2005

By Christian L. Escalera

Over seven years ago, on October 29, 2012, Superstorm Sandy pummeled the Northeast of the United States inflicting heavy damage on New York City Transit’s (NYCT) system. Since then, NYCT has been methodically rehabilitating and hardening its assets to upgrade service and prevent future impacts caused by similar devasting storm surges. Part of these resiliency efforts, NYCT’s 207th St Yard Project is one of many projects that make up the Sandy Repair and Flood Mitigation Program. The work to be performed on the 207th Street Project includes building a perimeter Floodwall along the Harlem River, extending up 215th Street and 9th Avenue with the intent of having the ability to withstand a 500 Year Storm flooding event. The original 1,535 lineal feet of the marine side floodwall design consisted of 937 each W40x235 H-Piles continuously welded to PS 27.5 flat sheet to form an interlocked and composite steel seawall that would protect the NYCT 207th Yard from a storm surge of the Harlem River. However, after the Contract was awarded and a Notice to Proceed was issued, Walsh Construction Company II (WCCII) partnered with Mueser Rutledge Consulting Engineers (MRCE) to propose a redesign of the marine wall section as a Value Engineering Change Proposal (VECP). This VEP redesign is comprised of 279 each 54in Diameter Steel Pipe Piles that are interconnected with continuously welded PZ 35 sheet piles interlocks. The intent of the VEP was to provide a cost savings that could be shared by both parties as well as alleviate some constructability and alignment control concerns that WCCII had expressed to NYCT. The VEP allowed WCCII to substantially lower the total cost which was shared between NYCT and WCCII.

By Helen Ahnberg

The scope of the present paper is limited to report the experimental evidence and not for describing the analytical assumptions. However, the idea behind the experimental program is that the deterioration may be caused by the leaching of Ca from the treated soil to surrounding soil or water driven by the difference in the Ca ion concentration. As a consequence of Ca leaching, it may be natural to expect the expansion of micro void space within the treated soil. In a saturated condition, the water inflow into the treated soil may accompany the leaching phenomenon. We measured the water content within the treated soil. But there is not much difference in water content within the soil.

Feb 10, 2003

By George Burke

Of the three projects, particularly the extensive Nimitz II (downtown) project, a single system, which was part of the operation, was used to control the spoil. Spoil control was continuous with the work since a vacuum truck and crew was used to suck up the spoils as they came out of the borehole. So, the whole job was kept clean both during operations and at the end of the shifts. On the Sand Island project, a double system was used. Larger spoil quantities were contained within the shaft limits during the work and the cleanup or disposal of the spoils was performed during excavation.

Feb 10, 2003

By Racquel Nottingham, Marc Mastrantuono

Micropiles often provide a favourable solution for many deep foundation problems especially when significant site constraints such as confined construction sites or vibration limitations have been identified. Often the durability of buried steel elements are heavily scrutinized in order to effectively determine the rates of corrosion and methods to reduce this while still maintaining the structural integrity of the engineered solution. Practices such as sacrificial corrosion loss and the introduction of plastic sheaths have become the go-to methods of corrosion protection. Since the introduction of the micropile, other solutions have been developed, namely protection with an adequate grout encapsulation. This paper will explore corrosion protection of micropiles and the guidelines provided in the published codes and norms. Since few codes define the exact way to verify the durability of these micropiled structures, the existing data is presented and the analysis of grout encapsulation as an effective corrosion protection method is evaluated.

Oct 1, 2022

By Ilhan Chang, Ernest Nsabimana, Kiseok Kwak, Juhyung Lee, Young-Hoon Jung

"Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.IntroductionWith the development of offshore technology, applications and real site installations of suction piles are increasing significantly nowadays. They are generally used as mooring anchors in various floating structures, marine platforms, and offshore wind turbines. According to its convenience in installation and removal, suction type foundations are becoming good alternatives for deep ocean support systems. The bearing capacity is similar to the bearing behavior of ordinary offshore structures (piles or drilled shafts). The most common use of suction caissons is anchors for catenary mooring lines, where the chain angle at the mudline is close to zero (Randolph, 2002; Sharma, 2004).Recently, it is reported that a huge isolated single suction pile can be replaced by a group of moderatesized suction piles (Randolph et al. 2004). A single monopile is easy to be produced and installed in site. It is expected that monopile foundation is not applicable for deep depths because it has a limitation on penetration according to its huge side skin area (i.e. friction). Moreover, stiffness requirements sometimes render thicker pile wall conditions which are impractical to be produced."

Jan 1, 2017

By Kaushik Mukherjee

"Malaysian offshore and surrounding region are favorable to the installation of driven piles. During the design phase, pile driveability analysis plays a major role in pile make-up design to suit and selection of the feasible hammer, besides defining acceptance criteria to ensure a certain level of confidence of its fitness for purpose. The accuracy level of driveability analyses depends substantially on the selection of its parameters that best represent the in-situ scenario. The most uncertain of the parameters are those related to the soil model. It is noted in various projects in the region, that the consideration of suitable soil resistance to driving, coupled with soil dynamic parameters, significantly affects driving sequence planning, design, material, hammer selection and most importantly pile acceptance criteria. This is particularly relevant for a region that contains predominantly clayey subsoil resulting in large diameter, long friction piles susceptible to driving disturbances and slow strength recovery. Various researchers suggested suitable dynamic parameters and soil resistance during driving calibrated to specific regions. Regional experience suggests a set of soil degradation and parameters to suit the different stages of driving which is corroborated by pile monitoring records during continuous and delayed driving scenarios. The most sensitive amongst all dynamic soil parameters is the skin damping in clay. Smith’s wave theory approach considers a conservative assumption in selecting the parameters in absence of site-specific data, while a different approach may be adopted based on consistency of the clay for a site where the geotechnical parameters are well defined. This paper summarizes some independent studies on the effects of variations in dynamic parameters and resistance at different stages of driving and suitability of choices of different pile make-up and hammers for an optimum design. Similar experiences, coupled with simulation studies and back-analyses of available driving records suggest a reasonable judgment for the region.INTRODUCTIONFixed structures are generally supported in the in-place condition on a pile foundation those may either be driven or drilled & grouted piles depending on the subsoil. The piles may be driven inside the jacket legs or drilled through individual skirts normally grouped in clusters at the base of each leg. The types of subsoil dealt with in the Peninsular Malaysia and Gulf of Thailand surrounding region are conducive to the installation of driven piles only. The design of an offshore pile is fundamentally the optimization of pile length, size and make-up those are suitable to the requirement and supply. An interactive effort combining aspects related to geotechnical, structural and constructability are required to converge into a feasible, safe and economic solution. Other than the checking of the installation feasibility using a set of hammers in a given environment, driveability analysis is also used to define acceptance criteria for a majority of the offshore piles. Unlike short and end bearing piles in sand/soft rock, the piles in clayey subsoil regime often could not be rested on a dense strata where it could be met by a definite set criteria. Usually a measurement of blow counts determined and defined by driveability analyses forms the acceptance criteria to ensure a certain level of confidence of its fitness for the purpose coupled with an optimum penetration. While softness and uncertainty of the soil strata at target penetration may be resulted in possible overdrive, an unusual delay or the presence of an unidentified cemented layer or a boulder may cause early refusal or underdrive scenario. Hence, accuracy of the investigation, driveabilty study as well as the precautionary measures to avoid delays during driving are of equal importance."

Jan 1, 2015

By Emre Biringen

Over the past decades, there has been an increasing recognition of the strategic use of pile-supported rafts in design of heavily-loaded structures to reduce total and differential settlements. However, such a hybrid foundation construction method has not been widely utilized in many countries, including the U.S., due to code limitations. In current practice, the foundation design is based on either (i) the bearing capacity of the raft supported by the subgrade soils, or (ii) solely the pile capacity. This paper addresses the potential use of such hybrid piled-raft systems, where the structural load is shared by both by the piles and the subgrade soils directly beneath the raft, in foundation design of power plant structures. The study assessed some of the characteristics of piled-raft behavior by undertaking three-dimensional finite element analyses of two raft sizes, and various pile layout patterns, including the rafts with piles distributed evenly and only in the central area of the raft. The computer software PLAXIS 3D with the Mohr-Coulomb constitutive soil model was used to facilitate the modeling of such cases. The results presented in this paper indicate how strategically locating the piles could reduce the differential and total settlements.

By Juhyung Lee

Numerical analyses were performed to analyze the behavior of two different type of suction piles (mono type and group type) under various soil layer conditions (uniform silty clay layer, uniform silty sand layer, and two-layer deposit consisting of clay and sand layers) and lateral loading locations (top, middle, and bottom of the suction pile). According to the results, mono suction pile shows maximum resistance when load is applied on its middle, regardless of the soil layer conditions, while group suction piles varies significantly according to the allowance on head rotation. When head rotation is allowed, the behavior of group type piles become similar to the behavior of mono suction pile. Whereas, when rotation is prevented, resistance is maximized when load is applied on the top head. Moreover, group suction piles show higher efficiency regardless of the ground condition and geological stratum. For further advances, concrete block on the top of group suction piles are suggested as an effective alternative method to prevent partial rotation and maximize ground resistance for group suction piles.

By Jennifer Peirce Brandt

Project documents and the United States Army Corps of Engineers? permit for construction of the Stemmers Run Relief Wastewater Force Main across the Back River in Baltimore County, Maryland specified a minimal width, steel sheet pile cofferdam and a 12 feet wide, pile supported, timber decked, causeway trestle ? both approximately 1700 feet in length. Due to the impractical width of the causeway, the contractor desired to combine the cofferdam and the causeway structures in order to minimize wetland disturbance and maximize access for construction equipment. The resulting support structure was a steel sheet pile cofferdam, approximately 17 feet wide, internally braced, and capped with transverse timber deck mats to serve as the access and work trestle for the trench excavation, pipe bent construction, and trench backfill. Construction of this cofferdam/causeway progressed from the north shoreline toward the middle of the river. Then, working back toward the north shoreline, the contractor excavated, installed the 54 inch diameter pipe and H-pile support bents, and backfilled the trench in increments of approximately 60 linear feet. Excavation spoils from one section were used to backfill the preceding section. As the pipe installation progressed toward the north shore, the steel sheet piling and timber deck were removed. As sufficient sheet piling and deck mats were removed, the contractor began the process anew from the opposite shoreline using the reclaimed materials. The project was complicated by the presence of deep, very soft, weight of hammer, silts and organic clays and an unbalanced, hydrostatic head of 20.5 feet. In addition, concurrent pile driving, excavating, and backfilling in successive cofferdam sections required the use of heavy, long reach, hydraulic backhoes, and a 200 ton capacity crawler crane which controlled the design of the timber causeway deck and its supporting sheet piles.

Jan 1, 2008

By Sepideh Damavandinejad Monfared

"In recognition of the practicality of using inclined micropiles as elements for foundation support to resist static and seismic loading conditions, specifically in retrofitting projects, this study presents an investigation into the behavior of an inclined micropile subjected to simultaneous lateral load and bending moment. Three-dimensional numerical simulations are performed using the finite element method to assess the influence of micropile geometrical parameters such as angle of inclination, length, and diameter on the response of micropile-soil system. The Mohr-Coulomb failure criterion is used to define the behavior of soil and stabilized soil around micropile materials and the micropile, constructed of concrete and steel, is assumed to be elastic. The interaction between soil and micropile is taken into account by defining interaction elements covering both tangential and normal behavior. The study is carried out using nonlinear FEM analyses. The results of these simulations indicate that negative micropiles, in which slip surface deflects downward, have higher lateral load capacity than positive micropiles with slip surface deflecting upward. The conducted research also shows that increasing the diameter and the length of micropile increases the lateral load capacity. Increasing micropile diameter is more effective in increasing lateral load capacity. A relationship is developed from statistical regression analysis of the finite element modeling computations to estimate the lateral displacement of a micropile inclined at an angle of 30o in silty sands. IntroductionMicropiles are small diameter (typically less than 300 mm), cast-in-place, drilled, and grouted replacement piles with steel pipes which after being conceived in Italy (Lizzi,1978), were originally developed for underpinning existing structures (Bruce et al.,1990) to arrest and prevent structural movement, upgrade loadbearing capacity of existing structures, repair or replace deteriorating or inadequate foundations or raise settled foundations to their original elevation."

Jan 1, 2017

By Abolfazl Eslami, Fatemeh Rostami, Sara Heidarie Golafzani, Mohammad Arabameri

Collapsible loess is classified as problematic soil found in most continents. The loess immediately collapses under stresses induced by axial compressive loading or the soil weight when exposed to moisture. In Iran, vast areas of the Golestan province are covered with aeolian loess deposits. This paper investigates whether the simultaneous effect of inundation and pre-loading in helical pile installation are operative and effective in improvement of Golestan loess. The effect of installation conditions on loess collapsibility is studied via two main approaches, i.e., field investigations and physical modelling. The experimental studies include installation of eight single helix piles in the Amirkabir University of Technology Frustum Confining Vessel, i.e., FCV-AUT. Also, four single helix piles with embedment depth of 3 m and diameter of 250 mm were installed in Golestan province and full-scale pile static loading tests were performed. The results indicated that the simultaneous application of crowd loading and water pressure during installation of helical piles results in better soil shear strength parameters. Moreover, high crowd stresses or low crowd stresses accompanied by water pressure during pile installation brings about similar load-displacement behavior of model piles installed in FCV-AUT and full-scale helical piles.

Oct 1, 2022