Search Documents

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

By T. V. Nethery

Introduction A brief account of the East Malartic fire is essential if this paper is to serve the purpose implied by its title. The fire originated in the timbers of No. 4 shaft at the 10th, or 1,570-foot, level; this was the top or collar of the underground sinking operations. At the time, sinking was in progress and the shaft bottom was 242 feet below the 12th station horizon, or 618 feet 'below the l0th level. Above the l0th level, the shaft was not in use as the surface plant was not yet completed. The shaft crews descended from surface in No. 3 vertical shaft to the l0th level, where they transferred to No. 4 shaft, a distance of 1,450 feet. Of the sixteen shaftmen mucking at the shaft bottom, four were able to reach safety. One shaftman was overcome by fumes midway between the two shafts on the l0th level, while attempting his escape. The remaining eleven men climbed as far as the 11th station and there succumbed to carbon monoxide. No. 4 shaft, inclined at 61 degrees, bad been raised and timbered from the 10th level to surface; this bad been followed by sinking operations below the l0th. Two air hoists had been set up in the footwall of the shaft, 110 feet above the 10th level, and directly behind compartments No. 2 and No. 4. The waste from the shaft bottom was hoisted in 28-cubicfoot buckets on mono rails and dumped over standard shaft sinking doors into waste chutes built into No. 1 and No. 3 compartments. The five-compartment shaft, 7 ft. 8 in. by 34 ft. 6 in. overall size, was heavily timbered. In addition to the standard shaft timbers of 8 in. by 8 in. and 8 in. by 10 in. B.C. fir, the hanging-wall and ends of the shaft were laced with 4-inch spruce lagging. This represented approximately 300 board feet of timber in placee for every foot of shaft. The cause of the fire bas never been determined, despite every effort to do so. The inquest held for those who lost their lives in the fire was an extremely thorough one, but only the location of the origin, and not the cause, was established.

Jan 1, 1950

By J. G. Thomson

Development of the Canadian North, a subject of growing national interest, must in part await the development of better forms of trans-port. The estimated 500,000 square miles of muskeg terrain in the north combined with the" scarcity of roads make essential the early development of special purpose muskeg vehicles. Good progress has been made in the last eleven years in classifying muskeg and some progress has been made in determining its mechanical properties. Limited travel is now possible through the use of special purpose tracked vehicles which have been built without adequate design data. A program to provide data which can be used to optimize muskeg vehicle designs began in 1957. The results of the second phase of this pro-gram are presented in this report. It is shown that vehicle performance in muskeg is directly related to the mechanical properties of the muskeg. Further, it is shown that good de-sign practice for tracked vehicles expected to operate in snow, sand, soft clays and loams is also good practice for muskeg vehicles. All indications are that muskeg mechanics is properly a part of conventional soil mechanics.

Jan 1, 1961

By A. E. Lehmberg

"IT IS KNOWN that some ores of sulphide type, such as pyrite, chalcopyrite, and bornite have an electrical conductivity comparable to that of metals, and accordingly much higher than the conductivity of any unmineralized rock. This physical property has long been used for the detection of orebodies of this kind by means of electrical measurements made at the surface of the ground.The present paper will deal with a new electromagnetic instrument for the investigation of subsurface conductors, which has been recently introduced into field practice and has already led to successful results in Canada.The principle of the instrument will be described. How it operates, and how the observations made can be interpreted will be explained. Field examples will •be shown to illustrate its application.Description of Instrument and of Operating TechniqueThe equipment (1) includes a low-frequency alternating current generator. The a.c. is supplied to a transmitter coil and generates a primary field which induces eddy currents in the ground, the intensity of which is proportional to the ground conductivity."

Jan 1, 1952

By Morgan Schauerte, Laura Raimondi, Mariel Palomeque

Executives in the mining industry are facing dramatically changing market expectations on reporting and transparency regarding the environmental and social impacts of projects, supply chains and products. Companies increasingly need to disclose the governance procedures they have in place to ensure communities, investors, employees, and Indigenous partners are effectively managing social and environmental risks. These disclosure requirements begin during exploration and carry through to all stages along the project life cycle. This type of environmental, social and governance (ESG) disclosure is referred to as ESG performance by the investment community. ESG is not a new concept, and it builds on and is intertwined with many concepts such as corporate sustainability, corporate social responsibility, eco-efficiency, triple bottom line thinking, life cycle management and many others. This paper will explore how mining companies can develop a credible ESG governance approach and strategy that will reduce risk, open opportunities, and create value. This paper will summarise ESG trends and drivers, discuss the economics and investors’ perspective towards ESG, and outline leading ESG standards and guidelines of interest to investors, regulators, communities and other stakeholders. Linkage of ESG to global sustainability efforts such the United Nations Sustainable Development Goals and Global Compact will also be addressed.

Jan 1, 2023

By P. M. Huck, R. John

"The National Uranium Tailings Program was established in 1982 to develop, in part, a mathematical predictive model which would allow the assessment of the impact of uranium mill tailings on the environment and particularly on humans. . To achieve this , various studies were undertaken to establish the role played by key constituents of the tailings. This paper summarizes the findings of a study carried out under that program, to examine the leachability of barium-radium sulphate sludges produced in the treatment of uranium mill tailings decants. The investigators performed detailed chemical an alysis of the sludge, applied geochemical computer models to investigate sludge leaching behaviour, and conducted experiments to assess the impact of bacteria on leaching. The modelling showed that the redox state o f the sludge-leachant system was the most important factor. Substantial bacterially-mediated dissolutio n of the sludge and release of radium was demonstrated experimentally under suitable reducing conditions . INTRODUCTIONIn September 1981, Phillip A. Lapp presented the final report of the National Technical Planning Group on uranium tailings research to the federal government (Lapp, 1981). Lapp' s group had performed an in-depth survey of the status of uranium tailings research in Canada and, as a result, recommended that a national program be funded in the amount of $18 .6 million. Half of this fund ing was to come from the federal government, with the two producing provinces , Ontario and Saskatchewan, providing the balance. However , the provinces declined to support the program and the federal government decided to inaugurate a reduced program with $8.5 million o f funds .In late 1982, the formation of the National Uranium Tailings Program (NUTP) was announced by the minister of state for mines. A primary objective of this program was to develop a mathematical predictive model that would permit the assessment of the impact of uranium mill tailings on the environment, a nd particularly on humans. The program was to use existing information to the greatest possible extent, and then fund research to fill in gaps or substantiate data where necessary .The NUTP was established to administer this program of contract research over a five-year sunset life. By the end of the 1986-87 fiscal year the NUTP had completed about 100 contracts. One of those projects was to study the effect of placing barium-radium sludge ba ck within the tailings matrix. Th is paper gives the results of that study."

Jan 1, 1989

By Chris Harris, Kamal Adham

The use of HCl acid is gaining momentum among hydrometallurgical processes. However, the issue of environmentally efficient and economically viable ways to regenerate HCl acid (from various metal chloride intermediate products) remains a technology and operational challenge. The authors provide a state-of-technology review based on Hatch’s years of testing, design and commissioning experience with high-temperature units (fluid bed and spray roasters), plus the recent efforts in the area of low-temperature HCl regeneration.

Jan 1, 2014

By J. H. Pee, Y. J. Kim, H. U. Lee, G. H. Kim

The general recycling process of tungsten scrap to produce tungsten raw materials (tungstic acid, ammonium paratungstate (APT) and WO3) have been carried out by the oxidation, milling, sodium-fusion, dissolution, and extraction processes. Many studies on the high temperature oxidation of tungsten scrap have investigated various aspects such as swelling kinetics, fracture resistance, and the effect of alloying composition. However, the accelerating factors on the scrap oxidation rate during oxidation were not considered here. In general, oxidized products were fused with sodium carbonate or sodium hydroxide to produce Na2WO4. Later in the process, solid Na2WO4 was dissolved in water. This process required considerable reaction time and was a costly process. Therefore, the aim of this study was to increase the solubility of solid oxidized products to produce Na2WO4 solution by hydrothermal reflux method. Na2WO4 solution was used to produce CaWO4 and H2WO4 by general chemical reactions with calcium chloride and hydrochloric acid. Ammonia solution was also added to the tungstic acid to produce APT. In this study, the effect of ammonia addition on the APT precipitation process was investigated in detail.

Jan 1, 2015

By J. C. Loretto, H. A. Simons

The paper discusses how, in the routine testing of ores, insufficient communication between the laboratory and the design personnel can lead to misunderstanding or misinterpretation of test results and consequent design errors. A number of examples are given together with suggested modified interpretations and the resulting dollar savings indicated by these new interpretations.

Jan 1, 1972

By Y. Mudryk, D. Paudyal, K. A. Gschneidner, V. K. Pecharsky, M. Khan

"Rare earth intermetallic compounds are utilized commercially as magnetic and battery materials, electron gun electrodes, etc. Several of these intermetallics will be briefly discussed. There are many other rare earth intermetallic compounds which are not utilized industrially but have unusual properties which are of fundamental interest and may have future technological applications. Several of these materials are discussed as well.INTRODUCTIONTens of thousands of rare earth intermetallic compounds exist, but physical properties (primarily their magnetic behaviors), other than their crystal structures have been measured for only a small percentage of these materials. Among these are the commercially important compounds: Nd2Fe14B, and the SmCo5 – Sm2Co17 family – well known high strength permanent magnets; (Tb0.3Dy0.7)Fe2, Terfenol-D, a giant magnetostrictive material; LaNi5Hx a critical component of the rechargeable Ni metal hydride batteries; and LaB6 an electron emitter. There are, however, many other intermetallic compounds which are not utilized industrially, but none-the-less, exhibit interesting, and sometimes, exotic physical properties which are of fundamental interest and may have some future technological significance. These include: the giant magnetocaloric effect compounds Gd5Si2Ge2 and La(Fe13-xSix)Hy; the RCu and RAg families of ductile intermetallics; the mixed intra-lanthanide (R,R')Al2 compounds in which magnetic transitions disappear and reappear as one R is substituted for by R'; and GdNi which exhibits large dilations along two crystallographic directions and a larger contraction in the third direction at the Curie temperature resulting in zero volume change as GdNi orders magnetically via a second order phase transition.COMMERCIALLY IMPORTANT INTERMETALLICSNdFeB Permanent MagnetsThe Nd2Fe14B permanent magnets were discovered in 1984 independently in the USA and Japan. It is a ferromagnet and with proper heat treatment and processing Nd2Fe14B is the strongest near room temperature permanent magnetic material known today. This intermetallic compound is utilized as a permanent magnet in many applications, such as electric motors (e.g. the modern automobile contains up to 35 electric motors), spindles for computer hard disc drives, microphones and speaker magnets for cell phones and other audio equipment, direct drive wind turbines, actuators, and Magnetic Resonance Imaging (MRI) units. There are two kinds of NdFeB permanent magnets – bonded and sintered. The bonded magnets have a lower magnetic strength than the sintered magnet. The highest strength magnets are obtained by small substitutions of Dy (up to a maximum of 10%) for Nd, because Dy can significantly increase the coercivity and thus the energy product (a measure of the magnetic strength or hardness). The bonded magnets account for about 12% of the NdFeB market (~82 metric kt per year, containing ~20 kt/a of Nd). The NdFeB permanent magnet market is growing at a rate of about 15% per year. (Burzo & Kirchmayr, 1989; Kobayashi & Hirosawa, 2001; Coey, 2011)."

Jan 1, 2012

By C. O. Swanson

Introduction It is thirty-odd years since I first entered the mining field by working underground at Anyox, which makes 1t clear that I can qualify as one of the older generation and claim the privilege of dealing in generalities and broad impressions. In this position I find it interesting to re~ view the salient changes that have taken place during the past quarter-century and indulge in some speculations concerning the future, with the hope that my comments may be of value to others engaged in the field of mining geology. As indicated by the title, the treatment is a perspective from a single viewpoint rather than an attempt to give a complete and impartial analysis. This plan, while deficient in some respects, has the advantage of being more specific than one based on .a. compilation of opinions. An additional advantage is brevity, which would be difficult to obtain on a subject of this scope if it were viewed from all angles. In conformity with the general plan, specific references to the literature have been avoided as much as possible, although a number of publications of general nature are listed at the end of the paper. This procedure is intended to give credit to the sources used without making them in any way responsible for the interpretation. The starting point for the discussion is the situation as it existed twenty-five years ago, when, as a recent graduate, I first had a fairly complete picture of it. However there is one impression of an earlier; stage that seems worth mentioning. In one of my first courses in geology the statement was made that some of the leading authorities of the previous generation, who guided geological thought at about the beginning of the century, were inclined to question the value of an association with mining. This attitude was no doubt exceptional, and certainly it was not adopted by the students who laid the groundwork for mining geology in North America. But its existence even in a limited circle is significant m showing how far the application of geology has advanced as the result of the investigations started during the first part of this century.

Jan 1, 1949

By L. Yuan, J. Qin, J. Xie, Q. D. Qu, Y. P. Liang

"This paper presents key outcomes of a major Asia-Pacific Partnership project between the Commonwealth Scientific and Industrial Research Organisation and Huainan Mining Industry Group Co. Ltd. to develop and demonstrate advanced technologies at Pansan mine, Huainan, China. A comprehensive approach assessed fundamental strata and coal seam methane conditions during mining and optimized mining sequences and coal mine methane capture systems. The project demonstrated a practical approach and procedures for advanced coal and methane co-extraction systems, improved mining safety and efficiency, increased methane capture and use, and reduced fugitive methane emissions.RÉSUMÉ Le présent article donne les principaux résultats d’un grand projet de partenariat Asie- Pacifique entre le CSIRO (Commonwealth Scientific and Industrial Research Organisation) [Organisation de recherche scientifique et industrielle du Commonwealth australien] et le Huainan Mining Industry Group Co. Ltd.; ce projet cherche à développer et à démontrer des technologies avancées à la mine Pansan, à Huainan, en Chine. Une perspective globale a évalué les conditions fondamentales des strates et du méthane dans les couches de charbon durant l’exploitation et a optimisé les séquences d’extraction et les systèmes de captage du méthane dans les mines de charbon. Le projet a permis de démontrer une approche pratique et des procédures pour des systèmes avancés d’extraction conjointe du charbon et du méthane, pour améliorer la sécurité et l’efficacité minières, accroître le captage et l’utilisation du méthane et réduire les émissions fugitives de méthane."

Jan 1, 2015

By John O. Galloway

"The year 1947 was a momentous one in the history of the petroleum industry in Canada. It was in that year that Imperial Oil Limited made its discovery at Leduc, the forerunner of other discoveries, large and small, and the spark wl1ich started a most intensive exploration and development programme there.If, to use boxing parlance, Leduc was the first blow of a one-two combination which left doubting Thomases groggy, then Redwater was the number two blow which achieved the knockout. The oil industry's exploration leaders did about-face without delay and the rush of oil operators of all classifications to western Canada began. It is still continuing, and the influx of capital which the operators have brought in and are bringing in has a bouyant effect upon the over-all economy. The boom is on, but it is a sound one, and it is difficult to conceive that it will have anything but the most beneficial effect on Canada, and particularly western Canada.The petroleum industry is an important segment of the general economy. Its activities call for tremendous amounts of capital; its employees are well paid; it is a large customer for a wide range of products of other industries; its commodities are essential to the citizens and the nation.The industry is carried on by highly aggressive and independent groups and individuals, of which a small minority are integrated while the majority are relatively small operators engaged in only one or two phases of the business. Competition is the rule and, since the nature of the business is mass production, the industry is faced from time to time with serious problems, many of which are peculiar to it."

Jan 1, 1950

By A. H. Lang

THE recent production of important quantities of high-grade muscovite at the Purdy mine, near Eau Claire, Ontario, bas brought that district into prominence and bas added another strategic mineral to the list of Canadian products. The discoveries are thirteen miles west of Mattawa and about two miles north of the Trans-Canada highway and the Canadian Pacific railway. HISTORY Clear mica of low power factor is in considerable demand in Canada and in the United States for war purposes such as radio and telephone condensers, aircraft spark-plugs, radio tubes, and transformers. Some muscovite (white mica) bas been produced in North Carolina and New Hampshire, but the United States trade bas depended largely on importations of muscovite from India and of phlogopite (amber mica) from Madagascar. For many years Canada bas been a substantial producer of phlogopite, but was unable to compete extensively in the United States with importations from abroad. Canadian production of muscovite bas been negligible as no important deposits were known. Ever since the construction of the Canadian Pacific railway, attempts have been made from time to time to mine the pegmatite dykes in and near the Eau Claire area, but, although some feldspar has been mined, no appreciable muscovite was produced. Lace in 1941, J. Purdy and H. MacDonald discovered a dyke containing large crystals of high-grade muscovite from which they are reported to have sold $700 worth of mica. They recorded claims 35974 and 35975 in December, 1941, and claim 36095 in May, 1942.

Jan 1, 1943

By B. McKevitt, P. Abbasi

The ion exchange process (IX) is applied in the mining industry for the removal of impurities from process streams, treatment of waste solutions prior to disposal and the recovery of valuable metals. Extensive studies have been performed with the goal of modeling of IX for the case of a single metal loading onto iminodiacetic resin in the hydrogen form. However, in a real system, a resin may be saturated by impurities (iron, calcium, magnesium, manganese), which are then displaced by the metal of interest. The present study provides an insight into the Fe2+ loading process onto iminodiacetic ion exchange resin under the infinite solution volume condition. The study involves the measurement of iron loading under a variety of experimental conditions as well as an attempt to model the loading process using the hybrid correlation advanced by McKevitt (2012). The importance of the experimental and modeling work are discussed in the context of resin in pulp recovery of nickel.

Jan 1, 2014

By M. Aljarrah

The phase equilibria in the Mg-Al-Ca system was investigated experimentally by differential scanning calorimetry (DSC) and X-ray diffraction (XRD) techniques similarly the Mg-Al-Sr system has been studied using DSC and XRD as well as scanning electron microscopy/energy dispersive spectrometer (SEM/EDS) and quantitative electron probe micro-analysis (EPMA). A new ternary solid solution MgxAl4,xSr was confirmed in Mg-Al-Sr system, which is a substitutional solid solution of Mg atoms in Al4Sr. Maximum solubilities of 21.3 at.% Al in Mg17Sr2 and 11.4 at.% Al in Mg were observed. It was also noticed that Mg38Sr9 dissolved 12.5 at.% Al. In the Mg-Al-Ca ternary system, one of the invariant transformations predicted by thermodynamic modeling was verified experimentally and found to occur at 512°C with composition close to 10.8 at.% Ca, 79.5 at.% Mg and 9.7 at.% Al. A ternary solid solution (Mg,Al)2Ca was confirmed where large solid solubility of Al in Mg2Ca was observed.

Jan 1, 2006

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By A. Giacomini, M. Nazem, E. Fathi Salmi

"Numerical simulation of collapse of tunnels in weak rocks is one of the challenging problems in rock mechanics. Collapse can impose technical and financial difficulties during the construction of underground excavations. This phenomenon, particularly in shallow excavations, may lead to propagation of a caved zone toward the surface and formation of chimney subsidence. Chimney subsidence has numerous catastrophic consequences such as the adverse environmental impacts and damage to surface structures in vicinity of excavations. Due to the importance of subsidence in civil engineering, the main goal of this study is to propose an appropriate method for preventing the formation of subsidence in shallow tunnels in weak rocks. The Dolaei road tunnel is investigated as a case study, where a large chimney subsidence has occurred. The geology of the area and the geostructural characteristics of the rock mass surrounding the tunnel are briefly reviewed in this paper. Two-dimensional as well as threedimensional numerical simulations are conducted to study the tunnel stability. Moreover, the effects of staged excavation and pre-supporting method on controlling the ground movements are studied. Outcomes of this study indicate that employing forepoling and staged excavation can be a practical remedy to control the ground movements and prevent the formation of chimney subsidence.INTRODUCTIONPredicting the formation of subsidence, mainly sinkhole subsidence over civil or mining excavations, is a very challenging task. An accurate prediction of subsidence is required for selecting an appropriate control and mitigation system to reduce the level of ground movements and its impact on the surface life (Bétournay et al. 1994; Leca and New 2007). Excavations, particularly in weak grounds, could result in surface subsidence; they modify the in-situ stress conditions as well as the hydrogeology of the area. Construction of unsupported excavations in soft soils and relatively weak rocks usually leads to the formation of a failure zone behind the face. In a very soft ground, the failure zone can extend towards the ground ahead of the tunnel face. Propagation of this zone toward the ground surface results in generation of sinkholes."

Jan 1, 2015

By Erwin L. Zodrow

"This paper is based on a statistical analysis of the Smallwood iron ore mine (6). In this mine, the prediction of magnetite is especially difficult because of strong trends. Recognizing the statistical limitations of the sample data, the paper approaches the basic statistical analysis of the magnetite by endeavouring to obtain a first approximation of its sample density function. The knowledge of the distribution of a random variable is essential for several reasons, but particularly: (1) to obtain reliable estimators of the population parameters -for example, mean and variance; and (2) to use these estimators in hypothesis-testing concerning future experiments -sample points and sample intervals."

Jan 1, 1968

By Nehad Elsafty

It is always necessary to expand existing buildings, so that they could meet the growing societal needs. Compared with demolishing them and then constructing new ones, the expansion of existing buildings could not only reduce project cost, but also save the use of energy and raw materials in projects. Therefore, it is widely adopted in most under-developed countries. However, the expansion of existing buildings is not an easy task. It has been involved with a lot of issues in defining the scope of work, planning landscape, managing construction activities, etc. This paper investigates the potential challenges in expanding existing buildings. The project of expanding the Al-Agoza Hospital, one of the biggest and oldest hospitals in Cairo, Egypt, is selected as a case study. In the case study, the project documents have been carefully reviewed. The project engineers and the health-care professionals working in the hospital have been interviewed. This way, the point of views from the owner, the architect/engineer, and the contractor have been taken into account. Several lessons are learned through the discussion with these people. The results from this paper are expected to provide pieces of useful advice and suggestion for the expansion of existing buildings in the future.

Aug 1, 2013