Search Documents

By K. Hanumantha Rao, A. Javadi

Our recent studies revealed that the sulfide minerals in contact with water during grinding produced hydrogen peroxide (H2O2) where the amount of H2O2 production by the minerals found to be in the order of pyrite > chalcopyrite > sphalerite > galena. The H2O2 effect on the oxidation of pulp components and its influence on the concentrate grade and recovery in flotation have been studied and the results have been presented and discussed in this paper. Studies have also been carried out to build correlation between percentage of pyrite in the concentrate, grinding conditions and concentration of OH•/H2O2 in the pulp and as well of controlling the formation of these species through known chemical means for depressing the generation of the oxidant. Flotation tests using a complex sulfide ore with the same reagent scheme that is being used at Boliden concentrator in Sweden but with the addition of i) collector and depressant, ii) Na2S reductant and iii) inorganic (EDTA) and organic (TETA) surface modifiers, during grinding stage have been performed to judge the beneficial or detrimental role of H2O2 on the selective flotation of sulfides. The results demonstrate that the selectivity of metal sulfides against pyrite increases with increasing generation of H2O2 in the pulp liquid. H2O2 is also found to be a better oxidant in chalcopyrite-galena flotation separation than the commonly used K2Cr2O7.

Jan 1, 2016

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By B. Arlyuk

On the basis of research of relations among the market participants the analytical model has been created which connects the price of industrial good at stock exchange with volume of sales and the stock of the sellers and buyers, Also a model was developed for assessment of these parameters of the market status by the actually fixed stock exchange and general market indicators. The composition of these models made it possible to create reliable system of short-term price forecasting for commodities or base metals up to one quarter ahead. Imperfectability of creation a model for reliable price forecasting by purely statistic methods (by the "black box" principle) was shown. A model of price behavior qualitative forecasting till one quarter ahead has been developed, which determines the probability of reaching in future of the given level as well as of the price maximums and minimums, Optimal values of threshold probability were determined for forecasting the future price maximums and minimums securing the maximum profit from the forecasting system application for commercial activity. The developed system of forecasting was identified for primary aluminium at the period of 1990-2003. The system was tested daily during 20 months period for speculations on 3M primary aluminium forwards at London Metal Exchange with high commercial result.

Jan 1, 2004

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005

By A. Lopez-Valdivieso

Particle size enlargement processes play an important role in solid/liquid separation, and in beneficiation unit operations. In the latter, not only the size of the formed aggregates but also their surface properties are very important. Oil agglomeration has a special place among such processes: it is a selective process in which hydrophobic particles are agglomerated into hydrophobic agglomerates which can be recovered by flotation. This explains the broad applications of oil-assisted beneficiation processes not only in the beneficiation of fine coal, but also in agglomerate flotation of many different types of ores, and in coal/gold agglomeration.

Jan 1, 2004

By V. Loya

Metallic foams (MF) are relatively new materials with a combination of attractive properties (permeability, high surface area, thermal and chemical stability, etc,), They can be produced from different materials and can be manufactured using various processes, Due to their unique properties, they find applications in different sectors of engineering, such as energy absorption, filtration, heat dissipation, etc, For many applications, the permeability is an important parameter to characterize and optimize, Most of the recent literature on the subject studied the permeability in the low velocity range. The present study was carried out to have a better understanding of permeability for greater velocity ranges, An equipment was designed and built for this purpose, Pressure drop measurements were made across the thickness of open-cell nickel foams, Pore and window sizes were measured by image analysis on SEM micrographs, The experimental results are in relatively good agreement with the Hazen-Dupuit-Darcy model (R2>98%), The permeability is affected by pore size, porosity and the normalized projected area of the connecting pores (ie. windows).

Jan 1, 2005

By V. I. Ryaboy, S. A. Kondratyev

"The paper describes influence of desorbed species (DS) of a number of xanthates and higher dialkyldithiophosphates on the collective ability of these reagents. Adsorbed on mineral DS of the reagents in the form of products of non-stoichiometric interaction between xanthates and heavy metal salts can pass to the gas–liquid interface and remove liquid from the layer between mineral particle and water surface. A high-speed video recording displays the process of spreading of DS of xanthates and dialkyldithiophosphates over water at the moment of local rupture of the water layer. Expansion of “dry” spot on the mineral surface after DS of xanthate capture and displace liquid from the layer has been proved with video images. The comparative analysis of collecting ability and dynamic surface activity of dialkyldithiophosphates shows that these characteristics are in good correlation. The forces exerted by spreading film of the reagent’s DS on liquid in the water layer are evaluated, and the water flow rate from the layer is determined. The line of the reduction in thickness of the water layer behind the front of spreading film of DS of dialkyldithiophosphates and xanthates coincides with the line of the increase in their dynamic surface activity. Their force on the liquid volume in the water layer characterizes collecting ability of the DS film of xanthates and dialkyldithiophosphates. It has been supposed that the collecting ability of DS of a reagent is a part of its overall flotation activity, conditioned by surface tension of solution and, thus, defined by the structure of hydrocarbon fragment of the reagent.INTRODUCTIONIt is believed that collecting ability and selectivity of collecting reagents is mainly governed by adsorption of a reagent at the solid–liquid interface. A few studies have shown that activity of collecting reagents at the gas–liquid interface may have deep influence on their collecting capacity and selectivity. Experimental researches have revealed correlation between surface pressure in a carboxylic acid film on liquid’s free surface and floatability of useful components (Kulkarni & Somasundaran, 1975; 1980; Quast, 2006). According to Quast (2006), it is not always that surface pressure of a reagent film influences collecting ability of carboxylic acid. For instance, pH range of adsorption of tetradecanoic acid on hematite does not coincide with pH range of high surface pressure. So, surface properties of this acid contribute little to flotation efficiency.The correlation between reagent film surface pressure and mineral floatability has been reveled for quartz and cationic reagents, too (Bleier, Goddard, & Kulkarni, 1977). Finch & Smith (1973) showed that combination of adsorption of ion–molecular amine complexes on mineral surface and high surface tension of “fresh bubbles” was favorable for flotation performance. The use of bubbles with reduced surface tension resulted in a decrease in quartz floatability."

Jan 1, 2016

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By M. R. Julien, A. Maqsoud, J. Martschuk, B. Bussière

Acid mine drainage (AMD) from mine wastes is one of the most challenging environmental problems currently facing the mining industry. When mining wastes have the potential to produce AMD, the effluents produced have to be managed to meet existing regulations on water quality. The LTA impoundment (property of Barrick Gold Corp.) located near Malartic, Quebec, contains sulphide tailings that have the potential to generate an acidic leachate. The closure option selected by Barrick was to construct a cover with capillary barrier effects (CCBE), in which the moisture- retaining layer is made of non-acid-generating tailings. Since its construction in 1996, the cover has been monitored to evaluate its performance. For that purpose, various parameters have been measured, including the volumetric water content and matric suction in the different layers of the cover. This paper presents some of the main results from the monitoring program that started eight years ago. The results show that the cover is able to maintain a high degree of saturation in its moisture- retaining layer, acting as an oxygen barrier. The actual performance of the CCBE on the flat surface of the 60 ha site is better than expected at the design stage. The only concern with the LTA cover is the effect of slopes that can reduce the performance of the CCBE during dry periods. However, these effects appear only for short periods of time, and are limited to very localized areas, so that they do not significantly affect the overall performance of the CCBE and its ability to limit the production of AMD.

Jan 1, 2006

By G. Knight

"Results of a program of dust research carried out at the Mines Branch Laboratory, Elliot Lake, indicate that dust-concentration estimates vary greatly, depending on the sampling instrument, the assessment technique and the properties of the dust cloud. The wide range of the ratio between the estimates by any pair of instruments shows that the correlation between the health hazard and dust-concentration estimates by most existing sampling instruments must be questionable. Important studies are being carried out to permit the definition of mine environments in more precise technical terms. The influence of size selection, the physical property measured, composition and sampling period on the assessment of the health hazard are discussed."

Jan 1, 1969

By Gurinder Kaur

Selenium (Se) based materials find wide applications in rectifiers, solar cells, photographic exposure meters, data storage devices, xerography and anticancer agents. They are also used in the glass industry to eliminate bubbles and remove undesirable tints produced by iron. In addition, Se is highly reactive towards a wealth of chemicals that can be potentially exploited to convert Se into other functional materials such as CdSe, ZnSe, Ag2Se. Here, we report a review of structural investigations of Se based materials in glassy and nanostructured forms. Glasses having varying amounts of Se and Tellurium (Te) were doped with group IV and V elements such as antimony and tin. Structural changes accompanying the composition variation were characterized with x-ray photoelectron spectroscopy, differential scanning calorimetry and x-ray absorption near edge spectroscopy. At the same time Se-Te nanoalloys were synthesized in aqueous micellar phase using Na2SeO3/Na2TeO3 as the Se/Te source. Morphology change from nanoparticles to nanoribbons was investigated using Scanning and Transmission Electron Microscopy (SEM/TEM) techniques. Structural investigations were also done for well defined morphologies of Se based nano-biomaterials obtained in the presence of water soluble protein bovine serum albumin (BSA).

Aug 1, 2013

By J. Pepin

When using alternating current submerged arc welding (SAW) to produce pipes from microalloyed linepipe steels, it is critical to balance penetration depth and deposition rates, in order to minimize the number of weld passes while still maintaining good heat affected zone (HAZ) microstructures and properties. A series of bead-on-plate (BOP) submerged arc welds were performed on X70 steel, using different waveform variable settings (i.e., balance, offset and frequency). Weld bead cross-section profile deposition and penetration areas were measured, and both Vickers hardness and Charpy V-notch impact testing were performed. Both single electrode and tandem electrode welds were evaluated.

Jan 1, 2011

"Ground control research in underground coal mines has been ongoing for over 50 years. One of the most problematic issues in underground coal mines is roof failures associated with weak shale. This paper will present a historical narrative on the research the National Institute for Occupational Safety and Health has conducted in relation to rock mechanics and shale. This paper begins by first discussing how shale is classified in relation to coal mining. Characterizing and planning for weak roof sequences is an important step in developing an engineering solution to prevent roof failures. Next, the failure mechanics associated with the weak characteristics of shale will be discussed. Understanding these failure mechanics also aids in applying the correct engineering solutions. The various solutions that have been implemented in the underground coal mining industry to control the different modes of failure will be summarized. Finally, a discussion on current and future research relating to rock mechanics and shale is presented. The overall goal of the paper is to share the collective ground control experience of controlling roof structures dominated by shale rock in underground coal mining.INTRODUCTIONThe National Institute for Occupational Safety and Health’s (NIOSH) Office of Mine Safety and Health Research (OMSHR), formerly the United States Bureau of Mines, has been conducting research on ground control safety for over 50 years. The overall objective of the research is to reduce underground mining injuries and fatalities by characterizing roof conditions, improving roof support performance and application, and optimizing pillar design and mine layout. Underground mining has one of the highest fatal injury rates of any industry in the United States—more than five times the national average compared to other industries (CDC, 2012). Roof fall injuries can be severe, resulting in lacerations, bone fractures, amputations, and death. Non-injury roof falls can also be problematic, resulting in lost production, delays, blockage of primary escape routes, disruption to ventilation, and hazardous rehabilitation conditions.Coal mining is increasingly subject to more adverse geological conditions. Weak roof can be found in all coal mining regions in the United States, but there are a few geographically isolated areas with higher roof fall rates contributed to by particularly poor roof conditions, as represented in Figure 1. This figure shows that when non-injury roof fall rates are normalized to production, the Illinois Basin and Central/Northern Appalachia regions have the highest rates. These isolated regions have inherently weak roof even before mining has occurred, and this roof is easily damaged during the mining process. The weak roof in these regions consists primarily of shale. Shale can be troublesome in underground coal mining because it can appear massive but easily splits along bedding planes and is often moisture-sensitive."

Jan 1, 2015

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By E. S. Moore

DEEP oxidation and-secondary enrichment of ore deposits, although so important in many parts of the world, are comparatively rare in the Canadian shield. Intensive glaciation during the Pleistocene epoch accounts for their rarity. Glaciation has cost Canada much in the destruction of not only enriched ore deposits, but placers that must have been developed near our numerous gold deposits during the long period of weathering that pre-ceded the Pleistocene. There seems to be a very common misconception regarding the average depth of rock that has been removed from the shield by glaciers. These bodies of ice are usually given credit for the removal of the greater portion of the thousands of feet of rock that we know has been eroded from this large area since Precambrian time. As a matter of fact, the average thickness of solid rock removed can be measured in tens rather than even hundreds of feet, although very deep erosion has resulted in some sections where the glacial ice has been constricted in depressions, such as deep valleys and lake basins. On the other hand, there are few areas within the shield where the glaciers have not disturbed practically all of the mantle rock and some feet of the underlying bed-rock. The chances of finding deeply oxidized cappings and enriched ore deposits are therefore comparatively few and these have been found chiefly where favourable structural and topographic conditions for their formation and preservation have existed. Faulting has been responsible for several of these deposits, and easily decomposed rocks, such as. sulphides and carbonates, have been very important factors. Topographic features, such as high and resistant hills, favourably situated with respect to the ore deposits have, in a few cases, played a part in providing protection from glacial erosion and in furnishing head for the descent of surface waters. At least four cases of oxidation to depths quite abnormal in the Canadian shield have so far been found in Ontario. These are the Helen and Josephine iron mines in the Michipicoten district, the Keeley silver mine in South Lor-rain, and the Ross gold mine in Hislop township, Cochrane district. A deeply oxidized zinc deposit of unusual interest occurs in the Precambrian rocks in New York State, not far from the Canadian border, and there arc the well-known iron deposits in the Lake Superior region of the United States.

Jan 1, 1938

By W. Dong

This paper presents the fundamental study of the temperature distribution in a reforming planar solid oxide fuel cell (SOFC) using mathematical modeling and experimental testing approaches at Versa Power Systems (VPS). In order to investigate the on-cell temperature distribution under high rates of Natural Gas direct internal reforming (DIR), both the computer simulation approach and the experimental testing approach have been developed. In this work, comprehensive in-house DIR and SOFC models were developed and employed for the computational fluid dynamics (CFD) based 3D computer simulation. The current SOFC module has been corrected to take into account both the on-cell electrical leaking effect and the stack stage structural resistance. Meanwhile, an instrumented single-cell test jig with multiple thermocouples was built, and a series of experimental tests were performed at various conditions. The numerical results based on the single-cell jigs are in very good agreement with the physical test results.

Jan 1, 2005

By J. Muralha, L. Lamas

"Given the results of triaixial tests, regressions are commonly used to evaluate the parameters of failure criteria that model intact rock strength and to perform statistical inferences used to evaluate characteristic values defined in EC7. Statistical robustness of these inferences is affected if the basic hypothesis underlying regression are not met, namely homoscedasticity (constant variance of the errors). This paper presents analyses of 23 sets of triaxial tests, starting by the evaluation of the regression parameters of the Mohr-Coulomb linear criterion and of the Hoek-Brown non-linear criterion, followed by carrying several statistical tests to check the homoscedasticity null hypothesis of independence between the variance of intact rock strength and the confining stress.INTRODUCTIONThough rock engineering design is clearly included in the scope of Eurocode 7(EN1997-1), its implementation raised a wide discussion regarding the applicability of structural safety concepts to geotechnical design of construction works in or on rock masses. The basis of the limit state design philosophy adopted in EC7 is that, for each particular design situation, all the possible limit states for a structure, or part of it, shall be considered and that it shall be demonstrated that the likelihood of any limit state being exceeded is sufficiently small. Though EC7 allows the limit states to be verified by one or a combination of methods, use of calculations is by far the most used, and it is often confused with the EC7 itself. It involves using characteristic values of actions, ground properties and geometrical data, as well as obtaining their design values by the partial factor method.Characteristic value of a given material property is defined in Eurocode (EN 1990) as: “value of a material or product property having a prescribed probability of not being attained in a hypothetical unlimited test series. This value generally corresponds to a specified fractile of the assumed statistical distribution of the particular property of the material or product”. As regards the design value of a material or product property, according to the Eurocode it is a “value obtained by dividing the characteristic value by a partial factor”."

Jan 1, 2015

By A. Aubin, H. Yang, G. Zaluski

The Athabasca Basin of northern Saskatchewan and Alberta is an exceptionally rich metallogenic region, hosting more than 2.8 B lb U3O8, of which over 927 M lb U3O8 have been mined out since extraction first started in the late 1970’s. A detailed compilation of several empirical features of 85 deposits located within the basin was conducted in order to understand the distribution and variability of the geological characteristics of the mineralization and its associated alteration. A new empirical classification was devised based on four parameters: 1) geometry of the mineralization (dimensions and relation to the unconformity surface), 2) size, grade and metallurgical complexity of the mineralization, 3) lithostructural setting, and 4) extent and nature of associated alteration haloes. This compilation defines the footprint characteristics of the Athabasca Basin deposits, which guides decision-making processes from early exploration and discovery to resource expansion and extraction.

Jan 1, 2020

By S. Mostaghel, Fariba Azgomi, Steven Goodman, M. Oliazadeh

"It is known that copper loss to the slag phase can be in the forms of chemical dissolution and mechanical entrainment. The contribution of each mechanism to the total Cu-loss depends on different parameters and may vary significantly. To reduce emissions to the atmosphere and to shorten the converting cycle, most industrial processes are aiming at production of high matte grades. Increased oxygen-to-sulfur potential, required by these processes, results in a highly oxidized slag, which in turn leads to an increased concentration of the chemically dissolved copper in the slag phase. Hence, slag cleaning processes are becoming increasingly important for economic viability of the smelting operations. Hydrometallurgical, pyrometallurgical, and mineral processing routes have been used for copper recovery from slag. The current article reviews a trade-off study evaluating two of the commonly used methods (namely flotation and electric slag cleaning furnace) by comparing the technical pros and cons, operability/maintenance requirements, and capital/operating costs of the operations.INTRODUCTIONLarge volumes of smelter and converter slags are produced by copper smelters around the world. It is estimated that for production of each ton of metal 2.2 tons of slag is produced (Gorai, Jana, & Premchand, 2003). Considering the current pressure on the mining and metals industry for “zero-waste, sustainable and environmentally friendly” extraction of metals, it is absolutely essential for metal producers to improve their efficiencies in order to remain competitive. To meet these objectives, almost all metal producers, from steelmaking plants, ferroalloys, base and precious metals producers, are trying to reduce their metal losses to the slag phase. In particular, copper producers are aiming to produce higher matte grades in their smelting furnaces to reduce the converting time and improve their overall throughput. Copper smelters need to minimize their copper/precious metal losses to the slag phase before final landfilling/use of slag. The current article, therefore, briefly reviews the copper loss to the slag phase, methods of metal recovery from the slag and then presents a trade-off study conducted for a green field flash smelter of the sulfide concentrates. A comparison was made between two of the major process routes for metal recovery from slag, namely slag cleaning furnace and flotation."

Jan 1, 2016

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilizationneutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre."

Jan 1, 2017