Search Documents

By G. W. Govier

Measurements of the settling rates and the rheological behaviour of heavy media formed of fine suspensions in water of each of magnetite, ferrosilicon, and galena have been made. For media ranging from 1.6 to 2.8 specific gravity the settling measurements gave initial settling rates of from 0.5 to 0.01 ?cm. 'Per minute for magnetite; from 4.0 to 0.8 cm. per minute for galena; and from 35 to 1.6 cm. 'Per minute for ferrosilicon. These measurements indicate the ?relative stability of the suspensions and should be helpful in establishing the useful specific gravity range for each medium. Measurements of the consistency of the media were made with a Fann Model 35 rotational viscometer. Aibnormal or non-Newtonian behaviour was observed in the case of each media, the apparent viscosity being dependent upon the rate of shear or the intensity of motion. Measurements were made over the rate of shear range of 10? to 1,000 reciprocal seconds. The apparent viscosities of the magnetite media ranged from 450 down to 4?0 centipoise at 2.30 specific gravity, and from 2,450 down to 700 centipoise at 2.80 specific gravity. In the case of the galena media, the variation was from 40, through a minimum of 6, to 10 centipoise at 2.20 specific gravity, and from 950, through a minimum of 180, to 450 centipoise at 3.6 specific gravity. The ferrosilicon suspensions exhibited apparent viscosities ranging from 42, through a minimum of 5.6, to 9 centipoise at 1.9 specific gravity, and from 160, though a minimum of 35, to 85 centipoise at 2.8 specific gravity. The dependency of apparent viscosity or consistency upon intensity of motion is considered to be of particular significance in applications of heavy media where the medium is in rapid motion.

Jan 1, 1957

By B. D. Sparks, I. E. Puddington, F. W. Meadus

The continuous separation of bitumen from Athabasca tar sands, with a high clay content, has been demonstrated. Recoveries of 95 per cent or higher have been obtained. Further processing of this product, to produce an accept-able type of crude oil, would require less heat than currently used in the hot-water process. Also, by comparison, substantial savings in equipment and operating costs are indicated.

Jan 1, 1971

By J. O. Yeboah, V. Boakye, P. A. Bepswa, M. Lombard, G. Nutor

The comminution circuit at Tarkwa Gold Mine was commissioned as a Single Stage SAG mill operated in closed circuit with hydrocyclones designed to process 4Mtpa. The circuit was later expanded by adding a secondary ball mill in closed circuit with hydrocyclones with a view to treat 12Mtpa. The change in the circuit configuration and assigning the low aspect ratio SAG mill for primary grinding application makes the Tarkwa experience unique in terms the optimisation strategy and operating philosophy. This paper reports the findings from a series of surveys performed on this plant. The surveys reported include data obtained when the SAG mill was operated as a single stage mill in closed circuit with hydrocyclones and also SABC mode under two different feed conditions. The differences in operating philosophy between the initial single stage SAG circuit and the current SAG/Ball mill circuit are discussed.

Jan 1, 2012

By A. R. Sheik, A. A. Baba, M. K. Ghosh, K. Sanjay, R. B. Bale, A. G. F. Alabi, F. A. Adekola, L. Ibrahim

"This paper studies the characterization and dissolution of a Nigerian pyrolusite ore, reporting the results of ore physicochemical analyses and detailed ore characterization before and after leaching at optimal conditions. Ore dissolution rate increased proportional to acid concentration and temperature, but decreased with ore particle size. In a 4 M H2SO4 solution at 80°C with a particle size of –90+75 µm and moderate agitation, ore dissolution rate reached 78.7%. Unleached residue produced under optimal leaching conditions consisted of silica with admixtures of cristobalite and stishovite. The calculated activation energy supported the proposed diffusion control mechanism for the process.RÉSUMÉ Le présent article étudie la caractérisation et la dissolution d’un minerai de pyrolusite du Nigeria, il donne les résultats des analyses physicochimiques du minerai et de la caractérisation détaillée du minerai avant et après la lixiviation sous des conditions optimales. Le taux de dissolution du minerai augmentait proportionnellement à la concentration de l’acide mais décroissait avec la taille des particules. Dans une solution 4 M H2SO4 à 80 °C, avec une granulométrie de –90+75 µm et une agitation modérée, le taux de dissolution du minerai a atteint 78,7 %. Les résidus produits sous des conditions optimales de lixiviation étaient constitués de silice avec un mélange de cristobalite et de stishovite. L’énergie calculée d’activation supportait le mécanisme de contrôle de la diffusion proposé pour le procédé."

Jan 1, 2016

By Jing Li, Weiqiang Lai, Joe Zhou, Jiezhen Ma, Shuibo Chen, Ashele Copper Company, Feng Gao, Guofu Feng

"Copper-zinc ores often contain gold and silver, which can be recovered into copper concentrate by flotation as by-product. The challenges for operations that produce copper, zinc, gold and silver are the separation of copper and zinc and the low grade of precious metals. Ashele copper-zinc ore in north China contains 2.38% Cu, 0.69% Zn, 0.21 g/t Au and 18.10 g/t Ag and the plant produces copper and zinc concentrates, with gold and silver being recovered into copper concentrate. Copper occurs mainly as chalcopyrite and Zn occurs as sphalerite. Copper is well recovered with a recovery of over 94%. However, the recovery of Zn is substantially low (around 50%) due to fine grain size of sphalerite. In addition, gold recovery is much lower than expected and only 33% of gold in the flotation feed was recovered. The grade of gold in copper concentrate is also lower than the required payable grade (1.0 g/t). To determine the cause for lower Zn and Au recoveries, a plant survey program was conducted on the operation. The information acquired shows that the loss of Zn was mainly in the copper concentrates (accounting for approximately 38% of the head assay); of which, 24% was liberated, 8.5% was associated with chalcopyrite and 4.6% was associated with pyrite, indicating that the separation of copper and zinc was the main cause for the Zn loss, with liberation being the second cause for Zn loss. Future effort in improving Zn recovery should be focused on the separation of zinc from copper. Gold in the ore occurs as both microscopic gold and submicroscopic gold, accounting for 36% and 64% of the head assay, respectively. Microscopic gold occurs mainly as native gold and electrum; it is relatively coarse with a grain size of 10 to 240 µm and a large portion can be recovered by gravity. Submicroscopic gold was mainly carried by pyrite (accounting for 38%), and to a less extent, by tennantite (15%) and chalcopyrite (10%). Gold in sphalerite is nominal (1%). It is suggested that more coarse gold and tennantite be recovered and a gold recovery increase can then be achieved to obtain a copper concentrate with over 1.0 g/t Au through flowsheet optimization. Gravity concentration should be investigated and may be worth added into the existing flowsheet to maximum the gold recovery and grade.INTRODUCTIONCopper-zinc ores containing gold and silver is a subtype of polymetallic sulphide ores. Unlike porphyry copper sulphide ores and iron-oxide copper-gold ores, this type of ores often contains substantial amounts of zinc and lead. Polymetallic sulphide ores are mainly distributed in Canada, such as at the LaRonde and Horne deposits. Other examples include Mt. Morgan in Australia and Boliden in Sweden. Globally, production and reserves from gold-rich VMS deposits account for 1370 t gold. This is equivalent to 1% of the world production and reserves, whereas the Canadian total for gold-rich VMS deposits is 870 t, representing close to 10 % of Canadian production and reserves (Gosselin & Dube, 2005a, 2005b). Flotation is the principal process for processing the copper-zinc sulphides ores, for subsequent smelting, roasting, or hydrometallurgical treatment. Oxidized copper-zinc ores can also be processed using leaching technology. For example, at LaRonde operation (a Cu-Zn-Pb ore containing 3-4 g/t Au and 60-100 g/t Ag) the flowsheet consists mainly of a copper flotation circuit and a zinc flotation circuit followed by a cyanidation process of flotation tails. The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation (Zhou et al., 2005)."

Jan 1, 2016

By M. B. Kime

"Discrete-element method (DEM) modelling is a powerful tool for studying particulate systems within the mineral processing industry. DEM simulations were conducted to investigate the power draw, load behaviour, and impact energy profile of an experimental ball mill under different milling conditions. The variables considered were mill rotational speed (percent critical speed), ball size, and lifter face angle. The simulation results indicated that the grinding efficiency would be enhanced by using 80% critical speed, 30 mm ball diameter, and 45° lifter face angle. These findings can be useful in guiding actual ball milling tests involving an ore sample.RÉSUMÉ La modélisation par méthode des éléments distincts (MED) est un outil puissant qui permet d’étudier les systèmes particulaires au sein de l’industrie de traitement des minerais. Des simulations par MED ont été menées de façon à étudier le profil de la consommation énergétique, du comportement de la charge et de l’énergie de rupture d’un broyeur à boulets expérimental dans diverses conditions de broyage. Parmi les variables prises en compte figuraient la vitesse de rotation du broyeur (vitesse critique en pourcentage), la taille des boulets et l’angle de coupe de la cornière élévatrice. D’après les résultats de la simulation, on pourrait améliorer l’efficacité de broyage en utilisant une vitesse critique de 80 %, un diamètre de boulet de 30 mm et un angle de coupe de 45 ° de la cornière élévatrice. Ces résultats peuvent se révéler utiles pour les essais concrets de broyage à boulets impliquant un échantillon de minerai."

Jan 1, 2017

By L. Heber Cole

Introductory During the past few years, salt (sodium chloride) strata have been encountered in western Canada in a number of wells, while prospecting for oil and gas. The ever increasing number of such wells points to the presence of a vast salt basin, the boundaries of which are at present unknown. This basin extends in a northwesterly direction from a point near the United States boundary south of Regina, crosses the Saskatchewan- Alberta boundary northwest of Unity, Sask., and continues with more northerly trend to Waterways and beyond. The beds, as encountered, appear to have a general dip to the southwest of between 10 to 20 feet to the mile and a pitch along the strike to the southeast. Thus one finds the salt strata at Waterways, Alta., at 600 feet below the surface (121 feet above sea level) whereas at Radville, Sask. south of Regina, the top of the salt is at a depth of 6,643 feet below the surface (4,430 feet below sea level). Whether this is a continuous salt basin or a series of separate basins is not yet known. We do know however, that in some of the well~ more than one salt horizon occurs while in others which normally should have encountered corresponding beds, the salt strata are absent. This latter condition, however, may occur only in the southern part of Saskatchewan, where a barren area seems to come in from the southwest. In the northwestern part of the basin, on the other hand, the occurrence of the salt strata seems to be more regular and continuous, and depths at which salt should be encountered in a drill hole in this part of the basin may be predicted with a fair degree of accuracy.

Jan 1, 1948

By Robert Maquil, Gilles Didier, Walter Steiner

"The 1580 m long dual-tube motorway tunnel Markusberg near Schengen, Luxembourg experiences strong swelling phenomena in each tube related to a 35 m wide diagonally crossing rock layer, some150 to 200m from the east portals. Overburden over the roadway is 26 to 30 meters. Tunnel construction started in 1998 and the tunnel was opened in 2003. The tunnel was driven downgrade from the West, the heave phenomenon started to occur as the tunnel approached completion. No indications of the presence of anhydrite and dissolved sulphates were known prior to tunnelling. Water samples had been taken from the beginning of construction and the concentration of anions and cat ions determined. Sulfate content was substantial, in one well it reached 22 mg/l, this high concentration requires the presence of other ions, in particular sodium and chlorine. Based on the knowledge at the time of construction heaving ground was removed from the tunnel invert and a free space was left below the roadway that is covered by a transversely spanned slab. In addition a series of posttensioned tiebacks were installed below the sidewalls. The void left in 2003 was 1.7m high and closed to less than 0.5 meters in 2007 then it became necessary to widen the free space. A central trench was dug with a height of about 2.5 meters and the benches were lowered.Level surveying had been carried out since 2002. In 2006 two extensometers were installed, one in the zone of strongest heave, the second at the edge of the swelling zone. The extensometer in the center of the swelling zone indicated heave with an essential constant rate with seasonal variations, the heave is concentrated in layer from 2 to 5 meters that heaved by nearly 300 millimeters within 5 years or 60 mm/year, which equals to approx. 1% extension per year. At the abutments heave rates of 20 mm/year where the support resistance is higher were observed. With data from other case histories a relation of heave rate with support resistance was established. Based on the numerous field observations hypotheses for the complex in-situ swelling processes, involving rock mechanics, mineralogical, soil mechanics and hydrogeological aspects were developed"

Jan 1, 2015

By A. Atrafi, L. Barroilhet

The top size of particles in the flotation of potash ores, which can be as large as 4 mm, exceeds by far the top size in other flotation plants. It is then understandable that while long chain amines are used in the flotation of fine fractions (below 0.8 mm) of potash ores the coarse particle flotation also requires an extender oil. While new and very promising fluidized-bed flotation machines (e.g. HydroFloat) constitute a significant development in the flotation of coarse particles, in the area of extender oils, as reviewed in 2007 by Strathdee, Gotts and McEachern, there have been no new developments to replace the industry standard asphaltene-based carcinogenic extenders. This situation first of all results from the experimental problems that arise when water-soluble minerals like sylvite are to be tested in saturated brine. Both oils and longchain amines are water/brine insoluble. The oil with the amine dissolved in it can however be emulsified and then used as an extender oil. Such oil droplets must wet KCl particles and the emulsion must be stable to avoid handling problems. In this paper we test the use of the phase inversion technique as a method of studying wettability of KCl particles by the oil in saturated brine, and the effect of amine dissolved in this oil on the wettability. The results show that this relatively simple technique can be used to characterize the wettability of fine KCl particles by the tested oil and to determine the effect of added amine on it, and so it can be useful in selecting proper extender oils.

Jan 1, 2016

By A. Montera, M. Loken

"The process of blending consistent and predictable feed for the roasters is critical for optimizing product quality and controlling production costs. To assist in this process, online PGNAA slurry analyzers have been installed and evaluated at a Sudbury Ontario smelter. They are used to measure 100 % of the full process stream to obtain elemental composition data in real time. This paper explains the application details at Sudbury and the benefits achieved from their full stream, elemental slurry analyzers.INTRODUCTIONSudbury Integrated Nickel Operations (Sudbury INO), a Glencore Company, consists of two underground nickel/copper mines in Sudbury, Nickel Rim South and, Fraser, along with the Strathcona mill and the Sudbury smelter. The facilities are spread throughout the 60 kilometer-long, oval-shaped geological formation known as the Sudbury Basin (Figure 1). The company has been mining nickel-copper ores in the Sudbury area since 1929. Nickel and copper are the primary focus of operations at Nickel Rim South and Fraser. Other base metals such as cobalt and precious metals are also produced.The Strathcona Mill receives ore from Nickel Rim South, Fraser, and third-party miners to produce two concentrate streams. One is a nickel-copper concentrate for use by the Sudbury Smelter; the other is a copper concentrate which goes to other Glencore operations for smelting and refining. The Sudbury Smelter converts the mineral concentrate into a high grade matte containing nickel, copper, cobalt and platinum group metals. This matte product is shipped to Glencore's Nikkelverk refinery in Norway for further processing. In 2015, the Sudbury INO Smelter completed the first phase of the Process Gas Project (PGP); a series of process changes and capital investments designed to reduce sulphur dioxide (SO2) emissions in accordance with Ontario Regulation 194. A critical element of the planned emissions reduction was the elimination of a higher percentage of sulphur contained in input concentrate streams, which can then be captured and converted to sulphuric acid."

Jan 1, 2017

By A. Ignatieff

This is the first in a series of Coal Technology Reviews being prepared in accordance with a recommendation voted by the Coal Division in session at the Jubilee Meeting, Vancouver, April, 1948, that the Department of Mines and Resources be requested to arrange for publication by the proper Government authority of a Quarterly Review' of Coal Technology, for distribution among those concerned in the production and use of coal in Canada. This recommendation was subsequently endorsed both by the Council of the Institute and by the Dominion Coal Board. Further reviews (or digests) will appear at intervals in the Bulletin, or will be published and distributed by the Board which, meanwhile, has undertaken to distribute reprints of Mr. Ignatieff's review.-En. * * * The fields in coal mining technology which are considered to demand most attention and study at the present time are reviewed under the headings appearing below. Mechanization In the light of the growing shortage of skilled miners and the necessity of mitigating constantly increasing mining costs, interest continues to centre in mining methods and applications of mechanization chat will produce the maximum reduction of man power. The growth of strip or open-cut mining, also, is a consequence of this trend. Mechanization at the face attracts most attention and the trend is toward developing and adopting machines capable of cutting and loading the coal in one operation instead of having the separate operations of cutting, drilling, blasting, and loading. In Great Britain, where longwall mining is? the general practice, the A.B. Meco-Moore machine still receives much attention, and accounts describing its performance over reasonably long periods have appeared in the technical press.

Jan 1, 1948

By A. M. A. Mohamed, F. H. Samuel, S. Valtierra, H. W. Doty, A. M. Samuel

"The influence of Fe, Mn, Cu and Mg alloying additions, Sr modification and grain refinement on the microstructure of as-cast and solution heat-treated Al-10.8% Si alloys was investigated using optical microscopy and EPMA techniques. The results showed that the modification effect of Sr diminished with increasing Cu and Mg additions, due to Sr-Cu-Mg interactions. Strontium caused segregation of AlzCu in areas away from eutectic Si regions, and altered the precipitation sequence of the a-Ah5(Fe,Mn)3Siz iron intermetallic from post-dendritic to pre-dendritic, with the phase observed within the a-Al dendrites. Depending upon the alloy Fe and Mn content, a coarser variation (""sludge"") of the a-Fe phase occurred, in the form of polyhedral shaped particles. The AhCu phase dissolved almost completely during solution heat treatment, while Al5Cu2Mg8Si6, sludge, and a-Aln(Fe,Mn)3Siz phases persisted in all alloys, particularly at high Mg and Fe levels. The f3-Al5(Fe,Mn)Si phase dissolved partially in Sr-modified alloys, the dissolution becoming more pronounced after solution heat treatment."

Jan 1, 2006

By Soumitry J. Ray

Poor visibility of powered industrial vehicles, such as forklifts, used in industry is often the cause of accidents that include pedestrians. Current standards allow up to 20 % non-visible regions for forklifts where measurement of these regions is performed by using lamps. A collaboration of research organizations, including National Institute of Standards and Technology, Georgia Institute of Technology (NIST), and Direct Dimensions, has been evaluating advanced methods for measuring a forklift operator?s visibility. These methods can potentially improve visibility standards. They can also help forklift and sensor manufacturers to determine (1) how visibility-assist sensors and algorithms can be designed and (2) where sensors can be mounted on forklifts. This paper includes explanation of visibility measurement experiments performed and results, associated language suggested to standards organizations, and a prototype design for measuring the visibility of forklifts automatically.

Aug 1, 2013

By Norman A. Grant

"Location and Transportation FacilitiesTHE BEAVERLODGE area of North Saskatchewan is on the north side of lake Athabasca, 500 air miles northeast of Edmonton.The main Eldorado operation and townsite are on the north •side of Beaverlodge lake, which is immediately north of lake Athabasca and is separated from it by only a mile long portage at Lodge bay. The once famous town of Goldfields. Saskatchewan, and the Box property of the Consolidated Mining and Smelting Company of Canada, Limited, are located on lake Athabasca nine mines from Beaverlodge townsite.Previously, all Eldorado freight was delivered by barge at the Lodge Bay portage, hauled across the portage, and across Beaverlodge lake by small Northern Transportation Company barges, which involved many handlings.In 1952 the port of 'Bushell' was established at Black bay. This is a particularly snug harbour, well protected from the main body of the lake and with good foundations for docking facilities. A Butler building, 300 ft. by 60 ft., and tank farms provide storage at the port. A •road from Bushell to the main Beaverlodge operation, a distance of twelve miles through rugged terrain, was built by the Saskatchewan Government. The cost was shared by the Saskatchewan Government, the Federal Government, and Eldorado and other mining companies.Along this road are located the properties of several enterprising mining companies and near the midpoint lies the ambitious budding town of Uranium. This road has made portaging unnecessary and palletized freight loaded at Waterways, Alta., is now loaded directly on trucks at Bushell and delivered to the point of consumption."

Jan 1, 1953

By Norman B. Davis

THE ceramic group of industries is comprised of those engaged in the manufacture of cement, glass, artificial abrasives, whiteware, including earthenware, stoneware, porcelain tableware, porcelain sanitary ware, electrical porcelain, floor and wall tile, porcelain enamel on metals, refractories of all kinds, sewer-pipe and structural clay products, such as terra cotta, brick, and hollow tile. The various sub-divisions of the industry produce a wide range of articles on which we depend for our creature comforts from day to day, perhaps to a greater extent than we generally realize. The industry, in turn, depends on a great number of minerals, and chemical products derived from minerals, and it is the object of this brief paper to present a list of these with notes indicating the particular applications. In order to bring home the importance of the industry to your daily life, stop and consider the many things around you accepted as a matter of course. Cement provides the smooth surfaces of many of our highways, city streets, and sidewalks. It enters into nearly all types of construction, alone or in combination with other clay products. Glass we hardly appreciate because we can see through it so easily, but it is there to serve us in windows, doors, and other light-transmitting structures. Glass is the universal means of transporting liquids and beverages, our beverages are usually served in it, and, with the recent development in fine spun glass textiles, there is a possibility of glass clothing in the future. Chinaware, a general term for table dishes, may be earthenware (not vitrified), semi-porcelain, or bone china, but it is before us three or more times a day ?and we seldom think of the minerals that have made these products possible. Floor tile, wall tile, and other ceramic specialties for interior and exterior use and decoration please the eye and provide sanitary surroundings.

Jan 1, 1938

By Ali Montaser

Hauling trucks are important part of equipment fleets for large earthmoving operations such as those encountered in dams and highway construction projects. This paper presents an automated methodology for tracking and estimating productivity of hauling trucks fleet operations in near-real-time. Recent advancement in automated site data acquisition technologies made their use in tracking and monitoring of construction operations feasible. However, these technologies fail to track hauling truck fleets due to the change in the cut and fill locations from one cycle to another; making tracking and progress reporting difficult and inaccurate. In addition, there is very little work done utilizing data sensed directly from equipment, for example sensing when truck dumping bed is raised during the dumping process. The technologies deployed in the developed method are Radio Frequency Identification (RFID) and equipment control sensors. Low cost passive RFID tags are attached to hauling trucks and fixed RFID readers are attached to loaders or excavators. The read range of the used RFID tag is centimeters, to be activated only when a loader with an attached RFID reader is loading a truck. On the other hand, control sensor is connected to the truck control system and operated by the motion of its movable bed. The function of control sensors is to record the signal time when the truck operator gives order to the truck control system to raise or lower truck bed. The captured data is then transferred wirelessly from the RFID reader and control sensor to a computer housed in one of the temporary offices onsite and subsequently to the main server in the contractor?s head office. Fusing the data captured from RFID reader and control sensor is used to identify loading, travel, dumping and return time that constitute the hauling truck cycle time. The collected data is analyzed and processed automatically, without human intervention, to calculate the productivity of the hauling truck and to report it directly to onsite personnel. Relational database is developed to support the implementation of the proposed method. The developed database is used to process the data captured by the RFID and the control sensor to calculate the productivity achieved in cutfill operations in near-real-time. The developed methodology is expected to facilitate early detection of discrepancies between actual and planned performances.

Aug 1, 2013

By E. Fiset, T. Hennebel, F. Verbruggen, A. Prévoteau, K. Rabaey

Arsenic (As), bismuth (Bi) and antimony (Sb) are known to affect the quality of copper deposits in copper electrowinning operations. The codeposition of As was previously believed to occur only at current densities far exceeding the range of typical current densities for copper electrowinning. In this study, we investigate the copper electrodeposition on different pretreated stainless steel (SS) substrates from bleed electrolyte in galvanostatic mode at –45 mA/cm². Scanning electron microscopy (SEM) micrographs illustrate that during the initial phases of copper nucleation and growth, the current density was locally increased due to the pretreatments. It was reasoned that the codepostion of As could possibly occur in normal electrowinning conditions, but the risk can be substantially reduced by good SS substrate handling and maintenance practices. INTRODUCTION The presence of As, Bi and Sb is known to have a deleterious effect on the copper cathode quality in copper electrowinnings (Hiskey & Maeda, 2003; Hoffmann, 2004; Xiao, Cao, Shen, & Volinsky, 2012; Xiao, Cao, Mao, Shen, & Ren, 2014; Jafari et al., 2017). They are known to influence both the chemical and physical quality of the copper as they can contaminate the copper (Jafari et al., 2017) and affect the copper deposit structure (Hiskey & Maeda, 2003; Kim, Kim, & Chung, 2009), which contributes to a degraded market value of the copper (Tuddenham, 1984). The incorporation mechanisms of these impurities are believed to occur mainly through slime inclusion (F. Xiao et al, 2012) and electrolyte inclusion (Hiskey & Maeda, 2003). Other studies suggested that codeposition of these impurities is possible by their standard reduction potential being close to the one of copper (Xiao et al, 2014). Hiskey and Maeda (2003) investigated the copper electrodeposition on a copper electrode substrate in Cu electrolytes with a Cu, H2SO4, As, Bi, Sb composition representative for commercial copper tankhouses. The combination of voltammographic techniques and Auger electron spectroscopy showed that As was the first impurity to be electrodeposited from this electrolyte, yet at potentials where the limiting current density of the copper electrodeposition reaction is exceeded. The copper tankhouses usually operate at a current density ratio of 0.3 to the limiting current density in order to achieve tolerable copper quality deposits. The codeposition of As could be considered impossible in this current density condition. However, it is known that during the initial phases of electrodeposition on foreign substrates, a substantial part of the reaction proceeds by growth of individual nuclei where the current density is locally high and diffusion limited (Radisic, Ross, & Searson, 2006). Furthermore, it was observed that copper nucleation on TiO substrates occurred preferentially in the scratched oxide free areas which could serve as parts with high localized current densities (Chang, Choe, & Lee, 2005).

Jan 1, 2019

By B. Karnath, K. Guha, S. Tandon

At Jhagadia Copper Ltd (India), Copper is produced through secondary route using Top Blown Rotary Converter (Kaldo Furnace). The basic raw material being treated includes Matte-slag Reverts, Copper Cakes, dross & Cement, Oxide Ore, Low S bearing Concentrates & various metallics along with high grade copper scraps. The plant has capability to refine & produce Blister grade copper from Kaldo furnace as well as PS Converter . Blister is fire refined in Anode furnace & electro refined in Refinery to produce cathode copper. Our product , Copper Cathode , has already been established in the market as its quality is better than 'LME Gr'. The paper deals with the experiences encountered during commissioning & stabilization of the plant.

Jan 1, 2007

By W. J. Mcgaughey, M. A. Vallée

"Abstract -The application of geophysical technology to resource delineation aims to improve the quality of resource/reserve estimates by integrating high-resolution survey methods, geophysical modeling and inversion with three-dimensional representations of geological and mineral deposit data. The use of geophysics can cost-effectively improve a geological interpretation based only on geological and sampling data. Success depends upon the ability to use geological visualization and modeling software, first to develop a three-dimensional geological model and then to modify it interactively by integrating geophysical data with the geological and sampling data.The high resolution required for mineral delineation geophysics results in a focus on borehole seismic and high-frequency electromagnetic methods. Borehole wireline logging is used to develop an understanding of the relationship between physical properties and geological description. Data from core samples and borehole wireline logs allow the construction of a three-dimensional physical property distribution, consistent with the existing geological interpretation. The three-dimensional physical property distribution is used for both geophysical forward modeling (to compare to field data) and as a starting model in iterative inversions.Advanced visualization techniques allow the simultaneous viewing of the three-dimensional physical property model, the geological information and data from which it is derived, and the geological interpretation and the geophysical results. Geophysical results may be simulated responses from a forward model or the output from a numerical inversion in the form of an updated physical property distribution. Iterative refinement of the geological interpretation is required to ensure consistency with the geological and geophysical data. The key to success with this approach is that all relevant geological, geophysical, and rock property data reside in a common, visual model of the earth.Examples from massive sulfide deposits illustrate the benefits obtained by the integration of geophysical and geological data."

Jan 1, 1998

By Joseph Hirschi, Behrooz Abbasi, Harrold Gurley, Yoginder P. Chugh

"The research goal was to assess if analytical tool/s can be developed to quantify displacements around a geological fault as longwall face moves toward it and past it. A company was faced with crossing a 2-3 m (6-10 ft.) normal up-thrown fault in the development entries and the face while mining a 375 m (1,200 ft.) wide longwall face. A field monitoring and numerical modeling study was performed to develop data. Field measurements consisted of roof-to-floor convergence and rectangular rosettes in the immediate roof. Numerical modeling consisted of constructing a 3-D structural model using the FLAC3D software with the fault plane incorporated as ubiquitous joint. Based on analyses and field observations data, the coal company was informed of impending movements along the fault plane and likely impacts on the development entries. Additional stiff supports were installed in head gate entries around the stage loader and equipment about 60 m (200 ft.) outby of the longwall face (solid). As the longwall face approached the fault, predicted displacements were documented and manifested by severe loading on the installed supports.BACKGROUND AND STUDY OVERVIEWThis paper summarizes results of a cooperative study aimed at improving longwall mining operations in Illinois. More specifically, the study focused on: 1) In-mine measurements in development entries while mining ahead of and behind a faulted zone, 2) Making observations on stability of pillars and entries while mining through the fault, and 3) Developing simplified analytical structural models using FLAC3D to assess if predictive techniques can be developed to plan mining operations through fault zone. Available data on geometry of the fault with estimates of the cohesion and frictional parameters were used for modeling."

Jan 1, 2015