Search Documents

By Dean Gerhardt

Why the need for proactive loose detection? ?? Past history of ground falls in Saskatchewan mines prompted research into new techniques for ground control. ?? Traditional tools for ground assessment (i.e. visual inspection, sounding with scaling bars) are not proactive and can often be time consuming. ?? Need existed for a system that was non-evasive, time efficient, and could be managed by a single operator. Ground Penetrating Radar (GPR) immerged showing the greatest potential.

May 1, 2008

By Alfred C. Lane

Reference to the original use of the terms Laurentian and Huronian (and its extension), shows that the former was applied to granitized sedimentary and metamorphic pre-Cambrian rocks, and the gneissoid igneous rocks associated therewith, and the latter to non-fossiliferous rocks supposed to be later. But it appears from the work of Collins, Quirke and others that there is more or less of an overlap, and that of the original Laurentian the Grenville limestone, and some of the granites, may be later than the lowest part of the original Huronian. Before we can decide whether to abandon one or the other of the two terms, or how to delimit them, it is important to know the extent of this overlap. The Pb :U ratio, though not to be depended upon too minutely, does give a real idea of the age of a mineral as it increases with the decay of uranium, and so is greater the longer the time since the uranium was separated: and there are reasonable prospects of help there from in getting a knowledge of the relative age of different granites to assist in solving the problem, as facts already collected show. 1. Historical review of the use of the words Laurentian and Huronian: 2. Difficulty encountered: 3. Popular account of atomic disintegration: 4. Methods of estimating age by it: 5. Applications.

Jan 1, 1925

By V. Vakiloroaya

The paper aims at developing a hybrid solar-assisted air conditioner system for performance enhancement and energy efficiency improvement. To increase sub-cooling of the refrigerant at partial loads, we propose a new discharge bypass line together with an inline solenoid valve, installed after the compressor to regulate the mass flow rate of the refrigerant vapour passing through a hot water storage tank. For control design, a lumped parameter model is first developed to describe the dynamics of the system in an explicit form of input-output relationship. The system has been fully-instrumented to examine its performance under different operation conditions. The system model is then validated by extensive experimental tests. The predictions from the models exhibit a good coincidence with experimental results, judging by an RMS error less than 15%. Based on the obtained dynamic model, a linear quadratic regulator (LQR) is applied to optimize a cost function of the output errors and control efforts. The key challenge is to regulate the refrigerant temperature entering the condenser by controlling the valve opening. The design approach is then tested in a transient simulation tool to predict the system performance in transient conditions. The experimental results obtained from implementation with PLC demonstrate that the proposed system delivers higher system efficiency owing to the higher refrigeration effect in the direct expansion evaporator. Thus, the novel development is promising for improvement of energy efficiency, enhancement of the system performance while fulfilling the cooling demand. Consequently, between 25 and 43% of monthly electricity can be saved on average.

Aug 1, 2013

By E. Johansson, T. Siren, K. Kemppainen

"As part of the preparations for the design of an underground repository for radioactive waste at Posiva’s Olkiluoto site on the west coast of Finland, there has been considerable site investigation work. Except the extensive surface based investigations, Posiva started in 2004 the construction of an underground characterisation facility termed the ‘ONKALO’. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. The research conducted in the ONKALO gives further information on the bedrock and groundwater conditions of the final disposal site, as well as on the impact of the construction. The ONKALO provides an excellent opportunity to investigate the rock at tunnel scale, to conduct in-situ testing in rock, to develop excavation and final disposal techniques in realistic conditions. The ONKALO has aided in collecting the data needed, supported by a Preliminary Safety Assessment, for the application of the construction license that was submitted in the end of 2012. The target is to begin disposal operations in 2022. According to current plans, the final disposal would end in 2112 and the repository would be sealed up by 2120. The testing in the ONKALO still continues several years. This paper presents the current characterisation and research activities in the ONKALO. INTRODUCTIONAfter the Finnish Government's favourable policy decision in 2001, Posiva Oy, which is an expert organisation responsible for the final disposal of spent nuclear fuel of the owners in Finland, has focused further investigations at the Olkiluoto site, western Finland (Figure 1) and has started in 2004 the construction of an underground facility termed the ‘ONKALO’. The ONKALO is not a nuclear waste repository, but more than just an underground research laboratory URL – it is an underground rock characterisation facility. The ONKALO has now been completely excavated to the anticipated repository depth i.e. -430–450 m. In addition to facilitating bedrock research, the ONKALO also provides an opportunity to develop excavation techniques and final disposal techniques in realistic conditions. Later, the ONKALO facilities can be put into use when building and using the repository. The construction methods and materials have been selected in order not to jeopardise the long-term safety of the repository site. The findings of the ONKALO and other investigations will provide the knowledge needed for an application, supported by a Preliminary Safety Assessment, to construct a final repository for spent nuclear fuel at the site. Posiva has submitted an application for the construction licence for a disposal facility in the end of 2012. The target is to begin disposal operations in 2022 and the repository would be sealed up by 2120."

Jan 1, 2015

By John W. Korczak

The use of geological and grade block models has been standard practice in mine design for many years now, with a wide range of software available for creation and analysis. Although geotechnical parameters are of vital importance to mine planning there is very little in the way of commercially available systems for integrating geotechnical data into the mine planning and design process. Sirovision is a new technology developed by the CSIRO (Commonwealth Scientific and Industrial Research Organization) in Australia for automated, safe and accurate 3D mapping of geological and geotechnical features. Datamine has integrated this capability into its product range so that Sirovision has become an integral part of the day-to-day mapping, mine geology and geological / geotechnical modeling in both open pit and underground mine environments. This is the first integrated underground application of Sirovision from Datamine collaboration with Xstrata Nickel at the Nickel Rim South Project. This paper discusses the role of Sirovision in collecting the raw data required for geological and geotechnical analysis and the interpretation in a quick, safe, auditable and reproducible manner.

May 1, 2009

By D. M. Baird

"THE Island of Newfoundland lies on the extreme eastern edge of the continent of North America and at the extreme northeastern end of the Appalachian geological province. Its belonging to the Appalachian province is shown in the geological history of the region and in the rock types and structures.Geosynclinal sedimentation in early and middle Palaeozoic times was interrupted by Taconic and, more profoundly, by Acadian, mountain building activity. Mid-Palaeo-zoic intrusions range from masses of serpentinized ultrabasic rocks to granite batholiths. A Carboniferous overlay of continental and shallow, drying sea types covers the earlier developed complex. Local basins in these times were filled with products of the erosion of tl1e earlier rocks, and, locally, grew the right kind of vegetation to make thin, discontinuons seams and pockets of coal. Post-early Pennsylvanian history is one of erosion and pene-planation with renewal of movement along many of the older fault systems."

Jan 1, 1960

By K. Jomoto, H. Majima

"Experimental work has been attempted to find a useful criterion of comminution which can be determined simply in a laboratory. The suitability of the ratio of the square of tensile strength to Young's modulus, St2/E, previously derived from the theory of elasticity as a criterion of comminution, was examined measuring tensile strength, Young's modulus and critical height for drop-weight impact of five different rocks. However, satisfactory correlation between St2 /E and critical height has not been obtained, suggesting the necessity of further experimental verification of the representative value of Young's modulus of rocks. The plot of St2 vs. critical height, however, shows one-to-one correspondence, and this finding suggests that St• may be a useful criterion of impact crushing. Also, a close relationship was observed between st• and the energy index for tumbling mill grinding of •the sample rocks. It is confirmed from these findings that the quantity St• is a useful criterion of comminution of rocks, not only for impact crushing but also for tumbling mill grinding. As shown in the experimental part of this paper, the determination ol St with irregularly shaped specimens is simple."

Jan 1, 1972

By C. J. Edmonds

Of the gold mined in Canada over 90 percent is extracted from the ore by the process of "cyanidation". In this process crushed ore is treated with lime to provide "protective alkalinity" and cyanide, usually in the form of sodium cyanide. The gold is dissolved in the cyanide solution, which after further treatments for clarification, is precipitated by the addition of zinc dust. Wastes from the process consist of tailings which will contain cyanides. Water consumption, mill size, effluent quantity and quality are depicted in transparency (1). It should be noted that as far as the wastes are concerned it has been impossible to postulate a typical situation. Variation from the above data will occur. A summary of data from tailings pond effluents is presented in transparency (2). The figures in parentheses indicate the usual range of values for the parameter.

Jan 1, 1973

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By Rob Kelso

What is a Lunabot? ?Robot Controlled Remotely or Autonomously ?Visual and Auditory Isolation from Operator ?Excavates Black Point 1 (BP-1) Simulant ?Weight Limit - 80 kg ?Dimension Limits - 1.5m width x .75m length x .75m height ?Designed, Built and Tested by University Student Teams

May 1, 2013

By P. A. Riveros

The literature on the arsenic disposal practices of the metallurgical industry and the long term stability of the disposed arsenic compounds were reviewed from a Canadian perspective. The review was complemented with visits to selected operating metallurgical sites to obtain information on their specific arsenic disposal practices and the behaviour of their impounded residues. The arsenic disposal procedure currently favoured by the industry involves the formation of an insoluble ferric arsenate compound which is allowed to sediment at the bottom of tailings or residue ponds. It has been shown recently that this poorly formed crystalline compound is similar to ?arsenical ferrihydrite? which is ferrihydrite containing strongly adsorbed arsenate anions. Despite concerns about its long term stability on thermodynamic grounds, arsenical ferrihydrite appears to be stable for many years in the proper environment which includes a slightly acidic pH and oxidizing conditions. A high Fe/As ratio and the presence of heavy metals appear to increase the stability of arsenical ferrihydrite. High temperature operations, such as those encountered in the autoclave treatment of refractory gold ores, are conducive to the formation of scorodite, FeAsO42H2O, and/or a series of ferric arseno-hydroxy-sulphate compounds depending on the solution composition. Scorodite has several advantages over arsenical ferrihydrite as a disposal compound including a lower iron demand, a higher density and a greater thermodynamic stability. New procedures have been developed to generate scorodite at ambient pressure. These procedures would offer significant reductions in capital cost because of the elimination of the need for autoclaves. Lime precipitation which was widely used in the past is being abandoned as a result of strong evidence showing that calcium arsenate compounds decompose slowly in contact with atmospheric CO2 to form calcium carbonate and soluble arsenic acid. In all cases, the long term stability of the disposed arsenic compounds depends on a number of factors including disposal site characteristics, particle crystallinity and size distribution, the presence of complexing agents and the effect of bacterial activity.

May 1, 2002

By F. Guo

"The leaching kinetics of zinc sulphide concentrate was studied under total pressures ranging from 0.3 MPa to 0.5 MPa and leaching temperatures ranging from 358 K to 378 K. The apparent activation energy of leaching reaction under different total pressures was calculated. The results show that for the extraction of zinc at low-temperature pressure leaching is controlled by an interfacial chemical reaction. This was supported mineralogical analysis of the leaching residue. The kinetic equation for low-temperature pressure leaching of zinc sulphide concentrate was further established by quadratic regression on the basis of shrinking core model.INTRODUCTIONThe Roast-Leach-Electrowinning Process (RLE) is the primary route for zinc production and responsible for more than 85% of the total zinc production (Souza et al., 2007). During the roasting of zinc concentrates, fugitive SO2 causes pollution. The prevention of SO2 emissions from the RLE process can be one of the challenges to this technology (Deller, 2005). In the 1980s, the Zinc Pressure Leach (ZPL) process changed the concept of zinc hydrometallurgy, in which zinc sulphide concentrate is directly leached at approximately 423 K and approximately 0.7 MPa oxygen overpressure and the sulphidic sulphur is oxidized into elemental sulphur so that the pollution by SO2 is completely avoided. Since 1981, five zinc plants have adopted the ZPL process either for expansion by integration with existing roasting facilities, or for the production of zinc without any roasting at all (Collins et al. 1994; Barth et al. 1998). The innovation of the ZPL process has made the zinc industries more competitive although it needs an autoclave. The direct leaching technology of zinc is still in development."

Jan 1, 2012

By Sylvie Poirier

This paper focuses on new developments regarding thermal rock fragmentation applications. The technology consists in a strong burner powered by diesel fuel and air. The thermal reaction, which is created, allows for the enlargement of 125-mm to 450-mm holes by breaking the rock in a spalling effect. It has been used for over 30 years in Russian open pit mining. Following an agreement between Dynamitage T.C.G. Inc. and the owner of the technology, major improvements have been brought to this technology, allowing for the fabrication of a prototype suitable for the Canadian industry. In Russia and Ukraine, thermal rock fragmentation is actually used to drill large diameter holes in surface mining. Upon having acquired a better knowledge of this technology, it seems that it presents a great potential for selective mining in narrow-vein operations, for either surface or underground mining. Rocmec International Inc., a subsidiary of Dynamitage T.C.G. Inc., and Natural Resources Canada are technical partners in the evaluation of the operational parameters and environmental aspects, such as gas, heat, dust and fog emissions. Furthermore, Canada Economic Development is a financial partner in this project. This paper presents the technology and its history. It also reports on the changes brought to the equipment to adapt it to North American environments. A summary of the tests realized since 1995 is provided, along with the main conclusions obtained. The anticipated applications for the use of this technology in both surface and underground environments are described, such as open pit mining, bulk sampling and narrow-vein ore extraction. An estimate showing a comparison between the thermal fragmentation mining concept and the long-hole mining method is presented and, finally, the future developments planned are listed.

May 1, 2002

By Franz Simon

Conventional fine gold electrolytes for barrel applications working electrolytically actually permit significant precious metal savings by corresponding optimizations but the most gold is still deposited on areas of the components where it is not absolutely essential for the desired bonding and soldering applications, i.e. in high current density areas. Therefore an electrolyte working electrolessly has been developed which inevitably leads to a much more uniform thickness distribution since in an electroless process there are no areas favoured by metal deposition and current distribution. The new electrolyte will be presented and its performance will be compared with conventional electrolytes as regards thickness distribution. The potential gold savings will be discussed.

Oct 1, 2003

By G. B. Hudson

Previous papers (1, 2) pertaining to the treatment of uranium-bearing ores were concerned with the flotation of the radioactive minerals. In this investigation, the application of flotation to the removal of acid-consuming minerals from uranium ores was considered. Two pitchblende-bearing ores, which, because of the presence if dolomite were abnormally high acid consumers, were studied. In both in-stances commercial reagents of widely varying fatty acid composition proved satisfactory as flotation col-lectors, particularly at a pH of 10.5, for the carbonate minerals. From an economic viewpoint, however, Neo-Fat 42-12 was favoured. A mixture of sodium tripolyphosphate and citric acid was an effective depressant for the pitchblende in the ores. The tailings remaining after the removal of the dolomite by flotation contained, in one case, 88.5 per cent of the uranium in the original sample, and, in the other, 93.8 per cent. Analyses conducted on these tailings and on the original ores showed that

Jan 1, 1963

By Timo Heikkinen

We have read, with great interest, Mr. Crocker's article on "Recent Trends in Autogenous Grinding," published in the October issue of The Canadian Mining and Metallurgical Bulletin. Referring to our paper, "Two-Stage Autogenous Grinding Investigations at Outokumpu," we can now report that last August we changed to this method at the Keretti concentrator. Prior to the conversion, the Keretti plant (see flow-sheet, Figure 1) had two primary rod mills, 6 ft. in diameter and 12ft. in length, in open circuit, followed by four secondary 9-by 12-ft. pebble grate mills in closed circuit with rake classifiers. Last summer, wl1en the Since August, grinding has been successfully carried out autogenously in two stages, with two mills being employed in the primary stage and four in the secondary. The size of the pebbles in the secondary mills is about the same as earlier -l V: i to 3 inches (Figures 4 and 5). Also, we generally prefer two-stage grinding to single-stage grinding because, in the former,

Jan 1, 1964

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By C. Campero, C. Nicolau, L. Pagliero

The Chilean Congress has recently promoted desalination as a solution to meet the mining industry’s growing water demand. However, this rapid expansion of desalination infrastructure comes with trade-offs. This includes a significant energy cost for treatment, as well as socio-environmental impacts on indigenous communities, tourism, fisheries, and the marine ecosystem. This paper advances a regional-scale model for analyzing competing trade-offs through a case study in the Antofagasta mining region of Chile. Through geospatial data analysis in ArcGIS, new desalination infrastructure investments supplying water to mines are overlain with features of concern raised by communities during the environmental impact assessment (EIA) process, such as national parks, fisheries and exploitation areas for benthonic resources. The resultant model provides a test-bed for analyzing the cumulative effects associated with desalination expansion and for investigating scenarios to mitigate negative social-environmental impacts. The model simulates alternative scenarios for desalination locations and pipeline routes according to competing constraints (i.e. to minimize cost and energy constraints while also avoiding ecological and social hotspots). The ultimate contribution of the work is a demonstration of how the proactive adoption of a regional-scale infrastructure planning might have led to different desalination investment decisions. INTRODUCTION Chile represents the largest producer of copper globally, and holds approximately a third of the world’s estimated copper reserves. However, access to water represents a major constraint to industry expansion and creates conflicts with competing water users (Aitken et al., 2016; Côte et al., 2010). Recently, the Chilean Congress has promoted desalination as a solution to meeting the industry’s growing water demand, which is likely to lead to significant growth in desalination infrastructure to support large-scale mining projects that extract freshwater over a rate of 150 l/s1. By most recent projections, the Chilean copper mining sector is set to increase seawater use by 230% by 2029 (Faversham House Group Ltd, 2019). By the year 2015, Chile had 11 projects serving the mining industry and there are at least other 12 planned plants (Cochilco, 2015). While the use of seawater allows continued expansion of the sector without depletion of scarce underground aquifers, it is nonetheless accompanied with important socio-environmental drawbacks. One such challenge with desalination is the associated energy costs, expressed, both economic and environmental (e.g., CO2 emissions). This includes the energy required for reverse osmosis treatment facilities, as well as to pump water to inland regions at high elevations around 3.100 m.a.s.l in Chile. (Dixon, 2013; Knops et al., 2013). Additionally, the impacts of desalinated water use on flotation chemistry are generally poorly understood, necessitating the need for further research into the impacts, both positive and negative (Cisternas and Gálvez, 2018; Liu et al., 2011).

Jan 1, 2019

By Roy S. Celland, K. H. Singh

The introduction of 'post' pillar mining at the Strathcona mine represents a new approach to ground support in cut-and-fill applications. The method has also shown significant economic advantages. It is believed that the development of this concept is one of the few examples where rock mechanics principles have successfully been applied in the development of a stoping method. The paper describes the evolution of this method and contains discussions on the theoretical analysis of the technical, operational and economics aspects of the system. Pillar design procedures and field observations on the practical application of theoretical analysis are also outlined.

Jan 1, 1973

By P. A. Gonzalez Contreras

Scorodite is considered as a secondary mineral formed from the product of weathering of primary minerals by chemical or biological reactions. In the case of biological scorodite formation, microorganisms mimic and accelerate what in nature takes a very long time, i.e. biocrystallisation. The goal of the biological scorodite formation is to form very stable arsenic crystals suitable for long-term and safe disposal. The biological formation of scorodite is a novel combination of biological oxidation, biocrystallisation, and proper bioreactor design to achieve the biological formation of scorodite crystals in one step. We have explored simultaneous biological arsenic and iron oxidation at 30ºC and at 70ºC leading to arsenic-jarosite phases and scorodite, respectively. As biologically formed scorodite crystals are very stable (TCLP < 1 mg/L As (V)), the risk of arsenic toxicity is minimized when leaching takes place. This process is suitable for arsenic concentrations above 0.5 g/l As achieving up to 20 mg/l As in the effluent. This biological scorodite formation system is a selfsufficient bio-oxidation system and therefore many new applications can be explored such as reprocessing of arsenic trioxide, orpiment or calcium arsenate to scorodite crystals for a stable and safe disposal.

Jan 1, 2014