Search Documents

By H. M. Beatty, T. L. Joseph, Gust Bitsianes

SUCCESSFUL blast-furnace operation depends upon securing an optimum balance between a number of important variables. This balance will vary somewhat from furnace to furnace in the same plant and with raw materials available in different plants. It is difficult to isolate the effect of any one variable unless it has a rather pronounced effect upon the efficiency of operation. The physical properties of iron ore and coke are known to affect the process, yet it is difficult to set up any definite yardstick by which these differences can be appraised. In recent years, whenever practicable, operators have taken steps to obtain better control over the absolute size and uniformity of size of the ore and coke. The size and physical character of the stone, however, have received comparatively little attention, emphasis being placed upon chemical composition, fluxing efficiency, and action as a desulphurizing agent. Since the stone occupies only about 10 per cent of the volume of the stock column, its influence upon permeability is less than that of the ore and the coke. The large pieces now used have a tendency to roll to the center and thus increase the permeability of this part of the stock column. Smaller pieces would be more effective in promoting the permeability of denser portions of the stock. The size and physical properties of blast- furnace stone are important also for reasons best understood by considering the results obtained by the crushing and the sizing of iron ore. Crushing ore to about 2 in. at Provo, Utah, and to about I in. in Alabama produced material somewhat less permeable to gases, even though sized. In spite of some sacrifice in permeability, the efficiency of the process was improved by crushing and sizing the ore, as indicated by a substantial saving in fuel and increased output. This saving in fuel is due in large measure to more thorough reduction of ore in the upper part of the furnace and to a corresponding decrease in the amount of carbon consumed prematurely above the tuyeres by the reaction CO2 + C = 2CO ? 70,080 B.t.u. [I] The physical properties of stone, its size and rate of calcination are important because they influence the rate at which C02 is released and the completeness of calcination before reaching a level in the furnace where the temperature does not exceed 1050°C. (1920°F.). Briefly, carbon dioxide from the limestone or from the reduction of ore may cause premature com- bustion of carbon above the tuyeres. Assuming that 1000 lb. of limestone is used per ton of pig iron, about 435 lb. of C02 will be liberated during calcination of a good grade of stone. If all this CO2 from the stone were to oxidize carbon prematurely, about 120 lb. would be consumed above the tuyeres in a heat-absorbing reaction. The amount of carbon thus consumed when a

Jan 1, 1942

Jan 1, 1902

[Trans. No,PlaceDate Vol. Page1 1. Wilkes-Barre, Pa*May, '71 13 2, Bethlehem, Pa Aug., '71110 3, Troy, N. Y Nov., '71.. 113 4. Philadelphia, PaFeb,, '72.. 117 5, New York, N, Y.*May, '72,, 120 6. Pittsburgh, Pa Oct,, '72,, 125 7. Boston, Mass Feb,, '73.. 128 8. Philadelphia, Pa,*May, '73., 23 9. Easton, PaOct., '73., 27 10. New York, N, Y Feb., '74,, 211 11. St. Louis, Mo,*May, '74.. 33 12, Hazleton, PaOct., '74., 38 13, New Haven, ConnFeb., '75., 315 14. Dover, N. J,*May, '75.. 43 15, Cleveland, 0Oct,, '75,, 49]

Jan 1, 1928

By J. B. Umpleby

PRoduction engineering in 1927 may be characterized by a great. clarification of fundamental conceptions, and many improvements in technique. During the year the profession has received tnarked recogni-tion by the industry and to an extent never before attained has become an integral part of it. History Petroleum production engineering is a new profession. Prior to 1925, when this Institute undertook the work, no forum existed for the open discussion of its technical problems. There was no attempt at a handbook of the subject prior to "Petroleum Production Methods by J. R. Suman, in 1921, and no textbook prior to Petroleum Production Engineering" by L. C. Uren, in 1924. As late as 1926, only six schools and universities offered special courses in petroleum production engineering. Prior to about 1923, engineers engaged by oil companies were used almost exclusively for construction and location work. Two of the leading production engineers in the Mid-Continent field, although with their respective companies more than twelve years, were not definitely assigned to production work until 1924. Both men now head large departments giving almost their entire time to production problems. Because of the newness of the profession, the leading production engineers of today have had their fundamental training in mining, civil, mechanical and electrical courses. Not unlikely this diversified training is in considerable part responsible for the amazing growth of the profession. I believe, however, that recognition is due principally to economic pressure within the industry which has directed attention more and more sharply on costs and efficiency. After all, the justification for the growth and continued development, of the profession is to recover more oil from a given unit of sand at less cost per barrel. In this new profession, it seems to me that greatest progress will result from focusing thought and effort on this single objective, and if I might offer one suggestion to the com-

Jan 1, 1928

By D. H. Turner, F. A. Crossley

The titanium-rich corner of the system Ti-Al-Si has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the means of investigation. PART of a program on phase relations and transformation processes of titanium alloy systems included the study of the titanium-rich corner of the Ti-Al-Si system. The investigation covered ternary compositions in the range 2 to 8 pet A1 and 0.1 to 2 pet Si and binary compositions in the range 0.2 to 2 pet Si. Temperatures were in the range of 600" to 1200°C. Alloys containing 6 pet A1-0.1 to 0.5 pet Si were investigated down to 400°C. Partial vertical sections are presented for 2, 4, 6, and 8 pet Al. The Ti-Si system has been reported by Hansen et al.' It is characterized by a eutectoid decomposition, ß = ± a + Ti3Si3, at 860°C. The maximum solubility of silicon in a is reported to be about 0.5 pet at the eutectoid temperature. The solubility of silicon in 0 increases from 0.9 pet at the eutectoid temperature to approximately 3 pet at the eutectic temperature, 1330°C. Several investigations in the composition range of interest have been reported for the Ti-A1 system."' These investigations are in agreement on the phase fields, but differ to small extents on boundary positions. However, very recent, and as yet unpublished, findings" " indicate that there are perhaps two phases which occur at lower aluminum contents than the ? (TiA1) phase, and that the solubility of aluminum in a titanium is less than 6 pet. In the present investigation phase relations found are in agreement with the published literature exemplified by the work of Bumps et al.3 Therefore, it is probable that the partial system reported herein is metastable and does not represent true equilibrium. Experimental Procedure High purity Bureau of Mines titanium sponge of 103 Bhn hardness, granulated aluminum shot of 99.7 pet purity, and silicon powder of 99.8 pet purity were used in making the alloys. For the work in the range from 600" to 1200°C, 100 g ingots were prepared by arc melting. Melting losses were negligible and spot checks by chemical analysis showed good agreement between nominal and analyzed results. Nominal compositions are used throughout this paper. Ingots were forged to 3/8 in. rounds and cut into specimens for heat treatment. Isothermal anneals in the range from 600" to 900°C were preceded by solution treatment at 1000°C for 1 hr, followed by furnace cooling to the annealing temperature. Samples were sealed in evacuated Vycor bulbs for heat treatments up to 1000°C. Higher temperature anneals were done with the samples sealed in quartz bulbs under a partial pressure of argon.

Jan 1, 1959

By C. W. Purington, H. B. C. Nitze

The Kotchkar mining-district, known as the Kotchkar System, is situated in the Orenburg government, in Eastern Russia, in the great plateau- or steppe-country immediately adjacent to the eastern slopes of the Ural mountains. Its longer dimension is north and south about 27 miles, while in the widest (northern) portion the distance across is 22 miles. The district lies 40 miles southwest of Miass, a station of the Trans-Siberian railway, and half-way between this village and that of Troitsk. It contains also the not inconsiderable settlements of Kotchkar and Eosobrodskoit., the last a Kossak town. So far as explored, the district is known to contain from 300 to 400 auriferous veins. ? Although the topography is generally of an exceedingly flat character, the country is traversed by several small rivulets running from west to east, and flowing into the Sanarka and Kamenka rivers. Since 1844 placers have been worked in the district, but it was not until 1867 that veins were discovered, and these have been worked only since the impoverishment of the alluvial deposits. The deposit with which this paper especially deals is known as the Ouspensky mine, one of twelve owned by MM. de Zelenkoff & Cie., five of which are situated in the Kotchkar System. An opportunity of visiting this mine was afforded the writers, in eonnection with an excursion of the VII. session of the International Geological Congress; held in Russia during the summer of 1897. The mine is reached by a 40-mile '(troika" journey from the railway station of Bichkil, itself

Jan 1, 1899

Jan 1, 1965

By R. Ward Grosz

Reasonable and timely solutions to the complicated mathematical calculations involved in the mine planning, economic evaluation and slope stability studies related to the Ruth Mine would not have been feasible without the modern digital computers. The Ruth Mine was a prosperous underground copper operation in east central Nevada from 1915 to 1948, when rising mining costs finally exceeded the value of the ore. A substantial reserve of porphyry copper remained in the ground, but until recently all economic evaluations indicated that it was at best a marginal operation and a relatively poor risk of capital. There has been a steady progress in improving all aspects of surface mining since the first steam shovel started stripping overburden; however, developments in just two rather specialized areas proved to be critical in changing the Ruth Mine from a reserve of mineralized rock to an economically attractive orebody. One involved the progress made in recent years in the science of slope stability. Applying the latest techniques in this field to mine planning resulted in reducing the stripping ratio from 6.0:l to 4. 2:l. The other major factor was the efficiency and cost performance of large capacity haulage trucks which made it feasible to go down over 1100 ft. in an open pit and recover ore with a high stripping ratio economically.

Jan 1, 1969

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By J. O. Lewis

The operation of gas-condensate fields is comparatively new and involves physical principles with which the industry was not prcviously familiar. It has been necessary to devise methods for testing gas-condensate wells and to correlate laboratory and field data. In this paper new methods are advanced for interpreting well G.P.M.† tests whereby dilution by dry gas can be estimated and information supplied on revaporization of condensates by dry gas. Inaccuracies in well test data are discussed. Changes in flow rates can cause changes in the G.P.M. of the effluent and it may take some time for a well to become stabilized after an important change in flow rate. Retrograde tests as usually conducted cannot be directly compared with field G.P.M. data, because the retrograde tests usually include solution gas in the condensates, which are reported On the cumulative basis whereas field data (G.P.M.) usually report pentaneS PlUS on a rate or instantaneous basis. Introduction Though long known to physicists, the phenomena Of retrograde condensation became known to the oil and gas industry Only in recent years, when deeper drilling disclosed that the behavior of vapors under changing pressures was different in high-pressure reservoirs than under the low-pressure operations with which the industry was familiar. These deep, high-pressure reservoirs in which condensation and vaporization behaved inversely to the accustomed manner became known as "gas-distillate," or preferably "gas-condensate" fields. Partly to prevent precipitation and retention of liquids in the reservoir, but still more to prevent the waste of residue gas, the operation known as "recycling," or preferably "cycling," was instituted, in which the residue gas is reinjected into the reservoir, thus maintaining pressure and driving the wet gas to the producing wells. For lack of field experience to serve as a guide, the industry had to assume that theory and laboratory experiments could accurately forecast retrograde behaviors in operating these gas-condensate fields, but it is obvious that these assumptions should be checked at the first opportunities against actual field experience. To make such checks, it is necessary to accumulate a large quantity of reliable field data, but experience has shown that it is difficult to obtain reliable field data and that the laboratory data as usually presented are not in directly comparable form. The problems of correlation involve the complex phase behavior on the one hand, and a knowledge of field data and a visualization of underground conditions on the other hand. This paper is an approach from field experience, The purposes of this article are to discuss the sources of uncertainty in the data and to present methods of analyzing, interpreting and correlating laboratory and field data. Data mostly from lower Gulf Coast fields are presented, from which some conclusions can be derived, but better data from more sources than those available to the writer will be required before satisfactory answers to many questions can be obtained. This paper is presented to stimulate the analysis and publication of data from other fields, the reexamination of field and laboratory methods, and the taking of more complete and reliable field tests. For these purposes, the writer presents some speculations that otherwise would not be appropriate.

Jan 1, 1947

By P. K. Lucke

ONE of the interesting features connected with the great continental uplift, which formed the table land of Mexico, is the great depth to which oxidation and secondary enrichment of orebOdies occurred. This table land lies at altitudes ranging from 4000 to. 7000 ft. (1219 to 2133 m.) above sea level. Several cases could be cited of oxidized zones in copper and lead mines which reached depths of upward of 1500 ft. (457 m.) below the surface, and it is universally admitted that the oxidized zone in a mine is limited by the permanent water level. FIG. 1. Mexico, however, like many other countries in which deserts occur, is visited at rare intervals by tremendous floods, which sometimes cause variable water levels over long periods. The following cases bear out the idea, and lead to interesting conclusions of commercial value. My paper demonstrates that carbonates of ores may occur below water level and sulphides above, and I will endeavor to explain the causes of the phenomena in certain specific instances.

Jan 6, 1918

By W. C. Maurer

A drilling-rate formula for roller-cone bits is derived from rock crater-ing mechanisms. This formula holds for "perfect cleaning", which is defined as the condition where all of the rock debris is removed between tooth impacts. Under these conditions, the drilling rate is directly proportional to the rotary speed and to the bit weight squared, and inversely proportional to the bit diameter squared and to the rock strength squared. Under imperfect cleaning conditions, such m those usually present in field drilling, re-grinding of the cuttings occurs under the bit, and the drilling rates fall below those for perfect cleaning. INTRODUCTION Drilling with a roller-cone bit consists of two fundamental operations: the formation of craters under the bit teeth, and the removal of the broken rock from the craters. To delineate the mechanisms of drilling, it is first necessary to understand the mechanisms involved in the formation of individual craters and then to relate these mechanisms to the over-all drilling operation. CRATER FORMATION When a bit tooth impacts a rock, the rock is elastically deformed until the crushing strength of the rock is exceeded, at which time a wedge of crushed rock is formed below the tooth1, 2 as shown in Fig. 1. As additional force is applied to the tooth, the crushed material is compressed and exerts high lateral forces on the solid material surrounding the crushed wedge.- en these forces become sufficiently high, fractures are initiated below the tooth and propagate to the free surface of the rock. The trajectories of these fractures intersect the principal stresses at a constant angle,'s4, as predicted by both Mohr's and Griffith's theories of failure. It has been experimentally 3,1 .6 that the volume of an impact crater, V,, varies as where Ec is the total energy imparted to the rock during the formation of the crater, and E is the threshold energy required before cratering is initiated (Fig. 2). Indexing experiments' have shown that, when there is a second free face to which the crater can fracture, a larger volume of material is removed and that above a transition zone there is a linear relationship between V, and Eo., which has a slope equal to the relationship for the single crater. The beneficial effect of indexing tends to offset the threshold energy requirement to a large extent, as shown in Fig. 2, and the relationship is closely represented by Rate-of-loading effects have been used to explain the nonproportional relationships usually obtained between drilling rate and rotary speed. The data4, in Fig. 3 show that the Ec/Vc parameter remained constant for craters produced with impact velocities ranging from 10 to 8,000 ft/sec. Since no rate-of-loading effects were detected over this wide range of loading rates, it seems improbable that there would be detectable rate-of-loading effects present in the small changes in impact velocities produced by varying the rotary speed. The writer has shown (Fig. 4) that, for craters produced in rock by impacting spheres, where X is the depth of penetration. Simon2 has shown that this relationship also holds for craters produced in rock by penetrating wedge-shaped chisels. The energy used in crater formation is

By F. M. Lewis, J. F. Myers

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

THE translators wish to record their appreciation of the help given by many individuals with whom they have discussed various details of the work. They are particularly indebted to Mrs. Anne Noble McKeachie, who initiated their collaboration; to Miss Cora Adamson, who spent many hours in making an accurate copy of a much-mutilated &st draft of the translation; and to the Yale University Library which gave access to its excellent collection of books on all aspects of the history of the sciences. The reader will share with the translators their obvious indebtedness to Mr. Carl P. Rollins, Mr. James W. Boyden, and the staff of the Printing-Office of the Yale University Press. The publication of this translation by the American Institute of Mining and Metallurgical Engineers has been made possible by a grant from the Seeley W. Mudd Memorial Fund, administered by a committee composed of Harvey S. Mudd, H. DeWitt Smith, and George Otis Smith. The translators are gratified that their work has been judged to fall within the scope of this Fund, which was established for the advancement of the sciences of mining and metallurgy by the encouragement of research and the dissemination of knowledge, and especially for the furtherance of such activities as might benefit the younger members of the profession. While Biringuccio's book would scarcely serve as a dependable text for the young mining student or metallurgist, it can give him a sense of his membership in a long-standing and honorable profession and enable him better to see his own work in true perspective. It is hoped that this English edition of a sixteenth-century Italian work will be read by the practicing metallurgist as well as by those who have already found pleasure in exploring the past of their profession. A man always feels more at home in a foreign country with men of his own craft than in his birthplace with those of different interests: As in space, so in time, and the modem metallurgist who may be unmoved by the literary and artistic Renaissance will quickly appreciate the spirit of that exciting period as he talks shop with Biringuccio on a visit to mine, smelter, forge, and foundry; as he sees in different forms the very furnaces and machines whose operation and response he knows so well; and as he discusses with this engineer of four centuries ago such topics as the best kinds of fuel or refractory for a given operation, and the importance of adequate supplies of power and material.

Jan 1, 1942

By John Mathews

DURING the prosecution of the aircraft-production program in 1917 and 1918, the writer visited many plants engaged in the manufacture of motors, planes and parts, in carrying out his duties as chairman of the Committee on Aircraft-engine Forgings. On several occasions, when the question of expansion was discussed, it was noted that there was confusion in the use of the terms: the true coefficient of expansion, a physical constant, and distortion in hardening. One engineer, referring to a steel shown in the accompanying table; stated that he could not consider it for crankshafts because of its excessive coefficient of expansion, while another steel, also listed in the table, as said to be especially good because it had no coefficient of expansion, since it came out of the oil bath perfectly straight. Many years ago one of our employees designed anew oil furnace; when asked what became of the products of combustion, he replied: "There ain't any, we burn them all up." While the coefficient of expansion is not without its effect in volume changes in hardened steel, it is not a determining factor in the matter of distortion and going out of shape. Irregular heating, uneven furnace bottoms, and carelessness in withdrawing the part from the furnace, as well as the manner in which the part enters the quenching bath are of greater moment. Generally speaking, also, steels of relatively low hardening temperature will distort less than those requiring higher hardening heats. The coefficient of expansion must be considered in engineering design most frequently when different metals or alloys are used in the same construction. For example, the difference of expansion between a steel crankshaft and an aluminum crank-case might be of real importance and a steel with no coefficient of expansion would be much less desirable than one with the normal coefficient. About 15 years ago, the writer made many determinations of the coefficient of expansion at low temperature ranges, usually between 20° and 100° C. Among the materials tested were: Pure forged electrolytic iron, 11.73 parts per million for 1° C.; cast aluminum (99.93 per cent. Al.),

Jan 2, 1920

By Gilbert E. Doan

IN a technical civilization, that is. one whose major difference from past civilizations is its enormous development of technology, in transportation, communication, labor saving, centralized control, and mass production, it is natural that the most critical problems should be those that arise out of technologic advances; it is natural also that a. man who understands these advances should be chosen as the leader to meet these problems. This was done in the selection of Herbert Hoover as President of the United States. Mr. Hoover was a good, and perhaps a great President. But he was not a great politician and that ensured his defeat when a crisis came.

Jan 1, 1939

THE first session of the Institute was held in the hall of the Washington University, Wednesday evening, May 27th, President Raymond in the chair. After the address of welcome by Hon. Thomas Allen, and the reply of Mr. Raymond, the following names were presented for election as members and associates, duly indorsed by the Council. They were unanimously elected : *Henry Booth, - New York City. *Charles H. Morgan, - Worcester, Mass. *Howard Painter, - West Chester, Pa. *Dr. M. J. Goodfellow, - Eberhardt, White Pine Co., Nevada *Otto Wittelshach, - Eureka, Nevada. *John T. Williams, - New York City. †Charles A. Young, - Philadelphia. *Charles E. Stafford, - Boston, Mass. *Arnold Hague, - Orange, N. J. *Richard Pearcé, - Black Hawk, Colorado. *W. R. Maffet, - Wilkes-Barre, Pa. *Prof. George A. Koenig, - University of Pa., Philadelphia *Prof. R. Nutting, Jr., - Indianapolis, Indiana. *Edwin Mickley, - Hockendauqua, Pa. *G. C. Broadhead, - St. Louis, Mo. *Dr. Adolph Schmidt, - St. Louis, Mo. *Alexander Leonhard, - St. Louis, Mo. *Edward D. Meier, - St. Louis, Mo. *John W. Meier, - St. Louis, Mo. *Prof. Forrest Shepherd, - St. Louis, Mo. *Edward Walsh, - Pilot Knob, Mo. *George Riggs, - St. Louis, Mo. †Col. Chas. B. Parsons, - Cadet, Mo. † W. A. Scott, - Mine La Motte, Mo. *Prof. Paul Schweitzer, - Columbia, Mo. *William E. Guy, - St. Louis, Mo. †William Harris, - St. Louis, Mo. *Henry Black, - Pittsburgh, Pa. †W. Noyes, - New York City. *W. Lorenz, - Philadelphia. †E. A. Whetmore, - New York City. * Members. †Associates.

Jan 1, 1875

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide's Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

By James P. Savely, Victor L. Kastner

Inspiration Consolidated Copper Company is currently mining in four pit areas; Live Oak, Red Hill, Thornton and Joe Bush Extension, near Globe, Arizona. Small satellite orebodies lying outside the main pits have been mined out in a series of small open pits. Major slope instability has affected production in every pit. Some consequences of the instability have been; (1) Serious interruption of mining plans, which resulted in deferred ore production, lost ore, reduced mining rates and increased stripping requirements. (2) Forced replacement of crushing facilities. (3) Serious effects on other production facilities. The introduction of a slope stability monitoring and control function as an integral part of mine planning has been successful in reducing the impact of these failures and will eventually result in economic pit design based on probabilistic slope analysis. This case history presents a brief review of the problems associated with slope instability at Inspiration's mines followed by a more detailed report on one specific failure area in the Thornton pit where the use of horizontal drain holes for slope stabilization appears to be successful. Relationships between slope movement rate, rainfall, and mining activity are shown.

Jan 1, 1983