Search Documents

By George Grandy

Kvaerner experience is being used to develop software to design or simulate crushing and screening plants. The model techniques discussed are presently being used for open-circuit plants and are being extended to closed circuit plants. The program contains a library of routines, each representing a piece of equipment or unit operation, which are assembled into one of several open-circuit plant configurations. Routines include gyratory primary crushers; standard secondary and shorthead tertiary cone crushers; single, double or triple deck screens; and stockpiles, feed bins and belt conveyors. The program uses steady-state models to simulate the performance of crushers and screens that have small residence times and quickly reach equilibrium when operating conditions and/or parameters are changed. The dynamic aspect of the total circuit model concerns the storage units within the circuit, i.e. stockpiles and bins, and, in the closed circuit configuration, circulating loads and size distributions. In many cases, just vendor's catalog data are necessary for a pre-feasibility simulation; in other cases, actual plant test data are required to obtain more accurate simulations. The entire plant is shown in a single graphic screen so the user can see all the relevant information he might want, and soft-keys are provided for the user to make on- line parameter changes and observe the effects on storage elements, equipment feed rates and the final product size distributions. The model also reports equipment utilization in percentage, power consumption, and other related operating information, and soon, will be able to report estimated capital and operating costs.

Jan 1, 1999

By Roma T. Dec

Many industrial wastes may require preliminary processing to change their particle size, density, surface properties or flowability to become more suitable for treatment and recycle. This can be achieved by pressure agglomeration using roll presses. In the following paper an overview of various roll press processing methods like briquetting, compacting, compacting-granulating or densification is presented together with basics of process and equipment design. The emphasis is focused on major factors influencing compaction process and responsible for pressure build up and final product quality. Finally, two examples of roll press application for briquetting of steel plant wastes and compaction of alumina base catalyst tailings are introduced.

Jan 1, 1996

By G. Springer

The identification of lost mineral values in mill tailings frequently requires the inspection of hundreds of thousands to millions of particles. The search of these particles can be made automatic by using an electron microprobe. A standard instrument (Cambridge Mark V) was modified by the addition of stepping motors to advance the specimen stage in a controlled manner. The X-ray Signal is monitored continuously by a computer interfaced to the instrument with an analog-to-digital converter. 400,000 particles of a tailings sample can be scanned in about 3 hours. Particles as small as 2 um and containing as little as 3% of a particular element can be detected.

Jan 1, 1982

By V. Ramachandran

Under the Resource Conservation and Recovery ACT (RCRA), generators of listed or characteristic hazardous wastes must find satisfactory means for disposal. of wastes. Initially, for many this meant landfills and deep-well injection. Until recently, mining and metallurgical by-products have largely been exempt from RCRA, but now are coming under its jurisdiction. With the increasing closures of landfills, companies in the U.S. such as electroplaters, miners, metallurgical plants and others are turning to recycling as an alternative to treat their wastes. While the cost of recycling has been challenging, the long-term economics prove attractive because recycling interrupts the cradle- to-grave responsibility for the waste generator. The present paper describes the recycling of hazardous wastes at ENCYCLE/TEXAS. Encycle extracts marketable metals from metal-bearing sludges and wastewater using hydrometallurgical processes borrowed from the mining and metallurgical industry.

Jan 1, 1994

By Gabriel Riveros, Ariel Balocchi, Andrzej Warczok, Daniel Smith

Blister copper from converting of copper matte is processed by fire refining prior to electrorefining. The fire refining consists of two steps: copper oxidation with impurities slagging and copper reduction. The classical batch process is carried out in vascular or reverberatory furnaces called anode furnaces. A new process for continuous copper fire refining has been proposed. The copper flows through two reactors in cascade, where is oxidized and reduced. The flow of a liquid copper through a ceramic packed bed increases the surface area and the rate of oxidation as well as the rate of reduction in the packed bed of charcoal. Mathematical modelling allowed for the design of a laboratory scale demonstration installation and industrial-pilot installation in Hernan Videla Lira Smelter (Paipote). The results have demonstrated the process feasibility and flexibility in operation.

Jan 1, 2009

By C. Gasparrini

Mineralogy may be applied to the selection of appropriate separation techniques, as well as to assist in the evaluation of problems causing loss of metals and other economically important elements during plant processing. Mineralogic studies may thus help develop techniques to optimize metal recoveries. The present paper describes how such factors as the minerals in which the elements of interest are concentrated, their chemistry, the chemistry of the associated minerals, grain size and textural associations with other minerals in the ore, may affect decisions on separation techniques for the recovery of economic elements. A number of case studies are described in which the mineralogical observation of ore samples has revealed the cause of problems experienced in the extraction of select precious and base metals, or has been decisive in the choice of appropriate techniques for recovery.

Jan 1, 1981

By M. Rosales

Using the k-e turbulence model, a mathematical fluid dynamics simulation of the flow characteristics in a Teniente converter has been conducted. Two cases were studied: - Transversal sections in the smelting-converting zone; and - A three-dimensional simulation that includes the walls of the reactor The calculations give the velocities field, the gravity waves amplitude, the splashing behaviour, the phase distribution and the shear stress distribution. The latter helps to explain the pattern of refractory lining wear. The calculation includes the approximate shape and dimensions, and the eventual coalescence of bubbles.

Jan 1, 1999

By James D. Navratil

Neutral bifunctional organophosphorus solvent extractants (such as carbamoylmethylphosphonates and carbamoylmethylphosphine oxides) strongly extract lanthanides and actinides and do not extract more than 40 other elements from mineral acids. Because of their excellent properties they have been found useful for F-element recovery and purification processes. A brief overview of the lanthanide and actinide extraction chemistry of these reagents will be given.

Jan 1, 1990

By Charles Washburn

The authors review mercury sources, and contaminant streams, with particular emphasis on mercury that is extracted from precious metal ores. The design and operation of both large and small mercury distillation facilities are detailed. The relevant properties and characteristics of mercury and mercury vapor are presented. Facility engineering with respect to industrial hygiene, area ventilation, and material handling is presented.

Jan 1, 2003

By Gordon A. Irons, Diancai Guo

"Uneven movement of scrap during melting in an Electric Arc Furnace causes operation problems: cave-ins interrupt electric power input. The movement also influences the radiation heat loss to water-cooled side panels and roof. An apparatus has been built to simulate the flow of scrap that may be interlocked. It has been observed that flow starts at the point where the suspended length of the pile bottom reaches the average scrap size, and proceeds in the form of cave-ins, but scrap pieces slide with each other as ordinary granules. After a cave-in, the pile angle usually remains much larger than the normally observed angle of repose. The force balance of a partially suspended scrap pile has been analyzed, and the equivalent cohesion due to interlocking estimated. A numerical model has been developed to simulate the scrap flow. Simulated results agree reasonably with observed phenomena.IntroductionWhen one considers the melting of steel scrap in an electric arc furnace (EAF), it is helpful to understand the movement of the material during meltdown. As industrial experience demonstrates, scrap movement greatly affects EAF operation. In a typical operation, scrap is dropped into the furnace from scrap buckets. The roof and electrodes are swung into position, and power is applied to the electrodes situated over the scrap. The electrodes ""bore"" into the scrap by melting into the steel in the immediate vicinity of the electrodes as they are lowered. If solid scrap pieces gradually slide towards the arc area, the electric power supply can be maintained at a high level, with few interruptions or drastic electrode adjustments. This results in a high production rate and low power consumption per tonne of steel produced. On the other hand, if the charge moves down unevenly, i.e. in large surges, usually called cave-ins, the electrodes must be drastically raised, and power supply frequently interrupted. This is also accompanied by a high level of harmonics induced in the power network, deteriorating the quality of electricity supplied to other users.In addition, the movement of scrap in an EAF also influences the furnace heat efficiency, as the scrap pile is much closer to the electric arcs compared to the furnace wall and roof, and absorbs more radiated heat. Early exposure of the wall and roof to the arcs will increase the heat loss due to radiation, and reduce the service life of the furnace."

Jan 1, 2004

By W. G. Davenport

Chapter 11 determined the combinations of industrial oxygen, oil and blast preheat that will steadily produce 65% Cu matte from pure chalcopyrite concentrate. It showed that the . combinations are described by a flat plane. It also showed that the minimum energy requirement for making 65% Cu matte occurs with maximum oxygen enrichment, zero oil and zero blast preheat. This chapter examines the, effect of matte grade on industrial oxygen, oil and preheat requirements.

Jan 1, 2001

By J. R. Addison

Commissioned in September 1987, the Phelps Dodge Morenci, Inc. (PDMI) Central Electrowinning (EW) Tankhouse bas undergone two major expansions in its eleven-year history. A third tankhouse renovation, which began in November 1998, entails complete conversion of the 548-cell facility from a copper starter sheet based operation to Mt. Isa Process stainless steel mother blank technology. This paper outlines the operating history of the Central EW Tankhouse and reviews the conversion process, the rationale that led PDMI to undertake this project, and describes various design optimizations which have been implemented during the conversion.

Jan 1, 1999

By Helena Byrdziak

KGHM Polska Miedz SA, in existence since nineteen seventies, operates three underground mines and three smelters with total production of over 400 000 mtpy of electrolytic copper. Its impact on the environment, very serious in the past, has been gradually reduced. While in general emissions into the air and water have been brought under control, attention recently has shifted to the disposal of wastes and residues. The main streams of wastes are flotation tailings, slags and dust captured from the dedusting systems. Much effort has already been expended and is still being spent to utilize this waste for by-products production or to dispose of it within the process by recycling. The most effective measures taken up thus far, as well as present activities directed at tailings disposal, are presented.

Jan 1, 1997

By Benjamin Vidales

Copper in concentrations above 0.5 weight percent in iron and steel causes hot shortness. This tendency is intensified in the presence of dissolved tin above 0.05 weight percent in the alloy. The understanding of the mechanism of removal of copper from molten iron and steel is of industrial importance. In this investigation, we present the experimental results of the removal of copper from molten iron using sulphide flux in the temperature range 1000°-1500°C. The solution thermodynamic properties of binary sulphide melts have been estimated by using the relevant phase diagrams and the behaviour of copper sulphide in these melts is discussed. The kinetics and thermodynamics of the removal reaction are also explained and, the experimental results are also reported showing the equilibrium distribution of copper and sulphur in molten iron.

Jan 1, 1995

Copper and gangue mineralogy constitute the most critical parameters for the hydrometallurgical processing and cost-efficient extraction of copper. Minor changes in copper-, rock-, or alteration mineralogy can severely impact the comminution efficiency, curing, agglomeration, acid consumption, copper extraction and PLS impurity loading. Further, copper leach operations, particularly in the southwestern United States, are increasingly challenged by a combination of low grades and semi-refractory copper. This paper discusses the metallurgical and economical benefits of continuous mineralogical analyses in order to establish and operate a mineralogical data base in copper leach operations. Troubleshooting for copper extraction, integration of process mineralogy into production forecasting, and process optimization will be illustrated with operational experiences from Chile and the United States.

Jan 1, 1999

By Peter Schwartz

This paper presents GBN's "Global Scenarios" for the first decade of the 21st century. We describe a set of key scenario actors and develop 6 driving forces in demography, technology, climate change, macroeconomic change, globalization, and geopolitics. We argue that a set of majorchallenges to world systems of commerce and politics will coalesce in the next several years. We develop four scenarios which differ according to how these challenges are handled, and which scenario actors play the key roles in managing the transition.

Jan 1, 1999

By Ioannis Paspaliaris, Dimitrios I. Gerogiorgis, Dimitrios Panias

"Red mud fiberization is a process with remarkable potential, alleviating environmental pressure by transforming an aluminum by-product into mineral wool, thus to various marketable products. A promising mineral wool process is molten slag fiberization via an impinging air jet, which avoids mechanical wear and rotating parts. The molten slag which remains after pig iron casting flows out of a heated ladle orifice at a high temperature (1600 °C) and adjustable flowrate, and forms a free-falling vertical jet which visibly radiates its excessive heat: at a given distance, a high-velocity impinging air jet meets the vertical melt jet perpendicularly (or at an angle), inducing intensive droplet generation, subsequent fiber elongation, collection and processing.This paper focuses on high-fidelity CFD modeling of the molten jet flow under external cooling: the model encompasses all physicochemical phenomena (melt laminar flow, radiative cooling) and considers several temperature-dependent slag transport properties in order to understand which operational degrees of freedom (manipulated variables) are useful to process optimization."

Jan 1, 2012

By O. A. Bascur

Applying the latest information technologies in mining and metallurgical complexes has become a serious challenge to management and technical teams. Emerging component design is changing the way the user relates to the desktop. Connectivity between mining and metallurgical process operations and their business systems has become a reality. Expanded use of plant information on the desktop is a standard tool for revenue improvement, cost reduction and adherence to production constraints. The industrial component desktop support access to information for continuous improvement and innovation by staff personnel and engineers. Collaboration between groups enables the implementation of an overall process effectiveness index based on losses due to equipment availability, production recovery and quality rate. The integration of information from mining, mineral processing and metallurgical performance monitoring increases production efficiency, even when many elements cannot be measured directly. Three case studies of large mining/metallurgical complexes are highlighted.

Jan 1, 1999

By Philippe Charlier

Recycling of aluminium contained in used aseptic beverage cartons is a difficult task which has nevertheless to be tackled by our modern societies. Techniques have earlier been developed by the paper and pulp industry for the recycling of the board fibres from collected post-consumer beverage cartons. A joint technical feasibility study by Granges and a leading beverage carton producer has dealt with different techniques for handling residues from repulping facilities. The aluminium obtained can be used as raw material for the production of thin gauge foil, thus closing the recycling loop.

Jan 1, 1995

By R. Parada

In January 1995, Disputada Mining Company Ltd. (Compañia Minera Disputada de Las Condes) started up the Expansion Project for the Chagres Smelter, following an investment of US$M 2 15. The new smelter replaced the 44,000 tomes per year revervatory furnace with an Outokumpu Flash Smelting Furnace (FSF) designed to produce 118,000 tonnes per year of copper. Nowadays, this smelting unit has achieved a 40% over design performance. The landmarks of this modernization project are described. The start up period in 1995-1996 was characterized by the impacts of several restrictions that prevented the smelter from reach design production. The design performance was reached in 1997-1998 through the implementation of solutions designed to eliminate, or at least mitigate, the restrictions found early on. The smelter has been further optimized in the 1999-2000 period, leading to a new record anode copper production rate of 148,000 tonnes in 2000 while obtaining 98% approval for our different anode shapes. The objective of this paper is to discuss the consecutive processes of start-up, achievement of design capacity, and operational improvements to go well beyond the design capacity. These processes took place between early 1995 and late 2000, under the principles of Continuous Improvement that promotes the effective participation of the workers in the technology innovation and Enterprise Management.

Jan 1, 2002