Search Documents

By Lucas Barbosa de Souza Martins, Felipe Perissé Duarte Lopes, Nathalia Carneiro Garcia Rosa, Lucas Lopes da Costa, Sergio Neves Monteiro, Rubén Jesus Sanchez Rodriguez

"The fibers extracted from the stem of the banana plant are relatively stronger and have been used as reinforcement of polymer matrix composites. In addition to quasi-static mechanical properties, there is a need to characterize the dynamic behavior of banana fiber composites subjected to thermal and mechanical constraints. In this work, the temperature variation of the dynamicmechanical parameters of polyester composites incorporated with up 30% in volume of banana fibers were investigated by DMA tests. The storage and loss moduli as well as the tangent delta were measured from 20 to 200°C in a TA Instrument operated with the flexural mode at 1 Hz. The results showed that the incorporation of banana fibers tends to increase the viscoelastic stiffness of the polyester matrix. It was also observed changes in the T g and the structure dumping capacity of the composites with increasing fraction of banana fibers.IntroductionNatural fibers with high amount of cellulose, also known as lignocellulosic fibers, have been used from primeval times by our civilization. In the last century, synthetic fibers such as nylon, carbon, aramid and glass fibers gained interest owing to superior strength and precise dimensional control. Natural fibers were then replaced by synthetics in many fields such as textiles and appliances. In the past decades, however, environmental issues drawn, once again, the attention to lignocellulosic fibers as possible substitute for intensive energy-consuming and long term polluting synthetics, specially the glass fiber [1]. In particular, research works have disclosed the potential advantages associated with the use of lignocellulosic fibers as the reinforcing phase in polymer composites [2-7]. Among the advantages it is worth mentioning the renewability, recyclability, biodegradability and the fact that natural fibers are neutral with respect to C02 emissions responsible for global warming. Moreover, as compared to synthetics, lignocellulosic fibers present lower density and cost as well as reduced wear caused to the processing equipment. On the other hand, in terms of composite reinforcement, hydrophilic lignocellulosic fibers present drawbacks such as weak adhesion to hydrophobic polymeric matrices in addition to dimensional limitations and non-uniform properties."

Jan 1, 2011

By Achilles J. B. Dutra, Carlos M. Juarez

"The use of thiourea as a gold leaching reagent has been extensively studied by many researchers, and it has proved to be promising for some cases as refractory ores. Otherwise, the recovery of gold from these solutions did not receive so much attention. In this paper the electrowinning of gold in acidic thiourea solutions was studied by voltarnmetry and chronopotentiometry. An adsorption step was detected prior to Au(I) reduction and the diffusion coefficients at 25°C for Au-TU complex and FD were found to be 1.00 x 10.5 cm2 S-I and 1.98 x 10-5 cm2 S-I respectively. At -0.350 V (SCE) a passivation probably due to TU adsorption was observed. For higher overpotentials hydrogen evolution was the main reaction.IntroductionThe use of acidic thiourea solutions for the extraction of gold and silver has shown to be a promising alternative to the traditional process of cyanidation, specially for certain refractory ores (1-3) and electronic scrap (4). In some cases, the industrial scale was reached (1,5). The thiourea leaching of precious metals presents advantages over cyanidation, as faster kinetics, lower toxicity and lower sensibility to base metals; however the costs due to high thiourea consumption impairs its use.The majority of the publications on thiourea processing of gold is on leaching. Many are review papers (5-7). Recently, the adsorption and desorption of the gold-thiourea complex on activated carbon and ion exchange resins have been studied (8-11).Little research has been done on the electrowinning of gold from acidic thiourea solutions, most of it has been carried on the seventies and beginning of the eighties in the former USSR (12-17) and concerned the eletrolytic extraction of gold in tridimensional cathode cells.The present paper concerns the cathodic behavior of the gold-thiourea complex in the presence of formamidine disulfide in order to provide information on the electrowinning of gold from solutions obtained directly from leaching or from an elution process."

Jan 1, 1997

By Jiakai Zhang

Many postconsumer electrical and electronic equipment wastes contain a considerable amount of rare earth elements (REEs); however, the current level of REE recycling from them is limited (<1%). Neodymium–iron–boron (NdFeB) magnets, used at both small- and large-scale, from computer hard disk drives and small tools to wind turbines and cars, are a good example of such waste materials that contain high content of neodymium (Nd) and dysprosium (Dy). These elements are considered critical metals because they are the main building block of emerging green technologies that will allow for GHG emission reductions. Because demand for these green products is increasing around the world, the demand for REEs is increasing quickly, putting their supply at risk in the near future. Thus, it is critical to develop efficient, robust, and cost-effective processes to recycle these elements from this class of electronic waste materials. Here, we performed a thorough characterization of a N52–NdFeB magnet to identify its composition, crystal structure, and morphology. Furthermore, we developed an efficient hydrometallurgical process to extract Nd and Dy with high efficiency (more than 95%).

By Scott Samson, Weidong Wang, Shekhar Bhansali, Vandana Upadhyay

"We present an improved design for the two-arm polysilicon thermal actuator. The classic thermal actuator design produces a localized hot spot at approximately the center of the thin actuator arm. This phenomenon limits the actuator efficiency, lifetime, and reliability. Since the actuator deflection is based on thermal expansion of the material, advantage may be gained by making the temperature profile more uniform along the hot-arm length. In our design, the geometry of the thin arm is modified by forming a nonlinear structure near the approximate location of the original hot spot. Electromechanical simulations of this design show an increase in deflection, due to a flattening of the temperature profile along the hot arm. The solid model generation, finite element analysis and simulations are carried out using PEA software. Experimental devices are in the process of being fabricated by using a polysilicon rnicromachining process.1. IntroductionMost active MEMS devices employ some kind of actuating mechanism to increase functionality. Various actuating mechanisms like magnetic, electrostatic, thermal, magnetostatic and piezoelectric have been investigated and incorporated for actuating microstructures. The primary features required from many on-chip actuating mechanisms are large deflection (>10 µm), low actuation voltage, low power.consumption, reliability, fast response, ease of design and fabrication, and small size. Thermal actuation is an attractive mechanism for rnicromechanical devices requiring high actuation forces, large deflections, good linearity and low actuation voltage. Thermal actuators, also known as ""electrothermal actuators"", ""heatuators"" or ""U-shaped thermal actuators"", have been largely used in MEMS based devices to provide both in-plane and out-of-plane actuation [l] .Thermal actuators are also easily compatible with standard CMOS circuitry due to their low driving voltage. However, high power consumption remains a major drawback of the thermal actuation mechanism."

Jan 1, 2004

By W. K. Connor, O&apos

The Bureau of Mines has conducted beneficiation, carbothermic reduction, and leaching tests of Mn oxide ores as part of its evaluation of the Mn and Co resources of the West- Central Arkansas District. The major Mn oxides in the ore include cryptomelane, psilomelane, pyrolusite, and lithiophorite. Cobalt is contained within the Mn oxides. Nonbeneficiated ore was reduced at 800&apos; C with coal and leached in ammonium sulfate and ammonium carbonate leach liquors. Ore concentrates were calcined at 600" C prior to reduction under the same conditions as the raw ore. Head analyses reported up to 21 ptt Mn and 0.11 pct Co. Extractions of 70 to 90 pct Mn and 40 to 60 pct Co were achieved.

Jan 1, 1992

By Baohua Li, Yanhui Liu, Shengping Li, Xuewei Lv, Yun Chen

There are almost ten billion tons of vanadium-bearing titanomagnetite in Panzhihua-Xichang area. However, iron ores in Hongge, which has the most abundant reserves in the four mine areas in Panzhihua, have not been utilized sufficiently so far. The reason behind this is the relatively high Cr2O3 in the ores (0.49 %~0.82 %), that due to its high melting temperature will negatively influence the blast furnace reduction and slagging process. Therefore, in the blast furnace process, Cr is hope to be reduced into molten iron, which can reduce slag viscosity problems. Slag iron reduction experiments were conducted to quantify the Cr reduction. Experimental results shows that with the increase of TiO2, the content of Cr in the hot metal is decreased when balanced. And during the initial stage of the reduction reaction, the reaction kinetic model is a first-order reaction.

Jan 1, 2016

By I. Ohnaka

Although many works have been reported on the semisolid casting, the mold filling behavior of semi-solid alloys has not been so well understood. This paper compares the physical and numerical simulation results on the mold filling behavior. Physical simulation was performed by using solid-water mixture. The numerical simulation was made under the assumption of one phase flow with an effective viscosity. It was found that the solid particles stabilize the flow greatly if the kaction solid exceeds about 0.4, because viscosity increases greatly. The overall flow behavior can be estimated by the numerical simulation. Interesting flow behavior was also found which can not be observed in the case of one phase flow and which is difficult to simulate by the one phase flow assumption.

Jan 1, 1997

By Heng Yi

The salt lake brines that lithium is extracted from have high chloride levels making the brine very corrosive to stainless steel extraction column internals. This is a significant problem in column scale-up to industrial production. Two types of corrosion-resistant ceramic internals, the hybrid ceramic internal and ceramic plate, were designed and tested under pilot conditions for future industrial application in this field. The hydrodynamic results (Yi et al. Ind Eng Chem Res 56 (4):999–1007 (2016), [1]) show that holdup of hybrid ceramic internal is higher than that of ceramic plate by around 50%, while Sauter mean diameter when using the hybrid ceramic internal is smaller than when using the ceramic plate by around 30%. This results in a larger mass transfer area, hence better mass transfer efficiency for the hybrid ceramic internal. Axial dispersion and mass transfer parameters are also examined (Yi et al. Ind Eng Chem Res 56(11):2049–3058 (2017), [2]). The results show that the column with hybrid ceramic internals has 50% lower axial dispersion coefficient and 50% higher mass transfer coefficient, leading to higher mass transfer efficiency. The transfer unit height of the column using hybrid ceramic internals can be as low as 0.2 m, showing very good efficiency. This is promising for near-future applications. Two-phase computational fluid dynamics (CFD) models have been developed for the two columns with ANSYS FLUENT commercial software. CFD successfully predicts the higher holdup and lower axial dispersion coefficients for the hybrid sieve plate pulsed column as measured in the experiments, and the cause for the difference in performance has been explained with information from CFD.

By Yichi Lu, Haydn N. G. Wadley, Douglas T. Queheillalt

"Using a 3-D ray tracing methodology combined with laser ultrasonically measured elastic constant data near the melting point, ultrasonic propagation in cylindrical single crystal bodies containing either a convex or a concave solid-liquid interface have been simulated and used to design new sensing concepts. Ray paths, wavefronts and time-of-flight (TOF) of rays that travel from a source to an arbitrarily positioned receiver have been calculated. Experimentally measured TOF data have been collected using laser generated/detected ultrasound on model systems with independently known interface shapes. Both numerically simulated data and experimental results have shown that the solidification (interfacial) region can be identified from ultrasonic transmission TOF data. Since convex and concave solid-liquid interfaces result in distinctively different TOF data. When TOF data collected in the diametral plane are used in a nonlinear least squares algorithm, the interface curvature has been successfully reconstructed and ultrasonic velocities of both the solid and liquid obtained. The reconstruction errors were found to be less than 5%.IntroductionMany of today's single crystal semiconductors are grown by variants of a vertical Bridgman technique in which a cylindrical ampoule of a molten semiconductor is translated through a thermal gradient, resulting in directional solidification and the growth of a single crystal, Fig. 1.1 It has long been recognized that during crystal growth the velocity and the shape of the solid-liquid interface, together with the local temperature gradient, control the mechanism of solidification (i.e. planar, cellular or dendritic), the likelihood of secondary grain nucleation/ twin formation (i.e. the loss of single crystallinity), solute (dopant) segregation, dislocation generation, etc. They thus determine the crystals' resulting quality.2-4 The solidification rate and the solid-liquid interface shape are also sensitive functions of the internal temperature gradient (both axial and radial) during solidification.5•6 This in turn is governed by the heat flux distribution incident upon the ampoule, the latent heat release at the interface, and heat transport (by a combination of conduction, buoyancy and surface tension driven convection, and radiation) within the ampoule. The solid-liquid interface's instantaneous position, velocity and shape during crystal growth are therefore difficult to predict and uncontrolled during growth, especially for those semiconductor materials with low thermal conductivity (e.g. CdTe).4-6 The development of technologies to non-invasively sense the interface position and shape throughout the vertical Bridgman crystal growth process has therefore become a key step toward developing a better understanding of the growth process, for enabling sensor-based process control, and thus ultimately for improving the yield and quality of difficult to grow semiconductor materials like CdTe."

Jan 1, 1997

By M. Kawakami

In relation to the designing of a new-type blast furnace, the reaction of carbonaceous materials with CO2 is expected to occur at as low temperature as possible. In order to get a highly reaetive carbonaceous material at low temperature, the reaction kinetics was investigated by measuring such quantities as the reaction rate from weight loss, the amount of CO adsorption and specific surface area by BET method. The reaction rates were large in the order of the Bintyo char, metallurgical coke, graphite and glassy carbon. If the rate was converted to the rate per unit area, however, those of the Bintyo char was smaller than that of graphite. Thus, it is suggested that the rate of the Bintyo char is influenced by the pore diffusion of CO2. The rate had a positive relation with the amount of CO adsorption, showing that the rate determining step would be the desorption of CO from the active side on the surface. The rate independent of surface area was derived, combining all the obtained data.

Jan 1, 2003

By Edward Peters

Scandium (Sc) has unique properties and is one of the more valuable elements in the periodic table. Scandium can be used in solid oxide fuel cells and to produce high strength aluminium alloys of value, for example, in the aerospace industry. Scandium is often grouped together with the rare earth elements (REE). Amongst others, scandium can be found in bauxite residues, so called red mud. It is possible to extract and enrich scandium from red mud by leaching and solvent extraction. Scandium can then be recovered from the pregnant strip liquor by crystallization. The strip liquor will however still contain certain impurity elements. In the present work, a method for obtaining a pure scandium solid phase by direct crystallization from the strip liquor is evaluated. It was found that Fe and Ti co-precipitate with Sc under the conditions employed.

By José D. T. Capocchi

Viscosity of liquid lead, tin, and Pb-Sn alloys has been measured by the rotational viscometer method in the temperature range from 50 K above their respective liquidus temperature to 823 K. The results are accurate to within ±1.0 %. The variation of viscosity with temperature followed the Arrhenius-type equation µ = µo.exp(Q/RT). The composition dependence of the isothermal viscosity and the activation energy for viscous flow have not shown anomalous changes at the eutectic composition of the Pb-Sn system.

Jan 1, 2000

By S. Peng, Vaughan R. Voller

"Free boundary problems are a common occurrence in materials processing operations. An important example is the filling of material into molds. This paper looks at filling problems associated with polymer processing, in particular Resin Transfer Molding (RTM) and Compression Molding. A general, single governing equation is developed which on numerical solution provides predictions for the position of the polymer front in the mold during filling. Both fixed and deforming finite element solutions are developed. Application to polymer filling test problems reveal that the fixed and deforming grid scheme are accurate and compare closely with each other.IntroductionProblems arising from the analysis of material processing operations often involve the tracking of a moving boundary, on which a balance conditions needs to be met, or the locating of a free surface that defines the solution domain. Material processing examples of so called ""free and moving boundary problems"" include; the tracking of solidification/melting fronts[l], the tracking of the metal/gas interface during the filling of a mold[2] and location and shape of a skull (freeze line) in a melting furnace[3].Computational solution of free and moving boundary problems usually fit into one of two classes, viz.1. Fixed grid scheme: In which the spatial domain is covered by a fixed grid (mesh) of node points and the solution uses an auxiliary variable (e.g. a local liquid fraction) to track the moving boundary or locate the free surface.2. Deforming grid scheme: In which the grid in the spatial domain is continuously deformed (or adapted in a steady state problem) such that a specified set of grid points lie on the moving boundary or the free surface.Details on the basic underlying features in these two classes of solution can be found in the excellent monograph by Crank [4]."

Jan 1, 1994

By Baozhong Zhao

Laboratory experiments have been conducted on the removal of As, Sb and Bi from molten copper by SF 6 injection. The results showed that the impurities can be removed by SF6 injection in the? sequence of Sb >As >,Bi and the rate of Bi removal is affected significantly by the concentration levels of As and Sb in the copper melt. Analysis of the experimental data indicates that the impurity removal process is under chemical reaction control rather than by mass transfer of impurity through the molten copper phase. On the basis of experimental results, a kinetic model was developed and the order of chemical reaction and the volumetric chemical reaction rate coefficients of impurity removal were determined.

Jan 1, 1996

By Takeshi Nagano

Copper pyrometallurgy in Japan has experienced quite fundamental changes in last fifteen years. The severe environmental restriction coupled with increase of energy costs accelerated the development work of the new continuous process in Mitsubishi Metal Corporation. After several years of pilot plant test work the commercial plant was put into operation at Naoshima Smelter in 1974, the design capacity of which was 4,000 tonnes of copper per month. Many modifications and improvements have been incorporated into the process and 7,200 tonnes per month of copper production was achieved in 1983, proving that continuous process was much more economical than conventional process. It is now possible to design and operate the continuous process in wide range of capacity. This paper will review the process and describe the progress of the process in these 10 years. 311

Jan 1, 1985

By Nagahiro Saito, Takahiro Ishizaki, Mituhito Hirota, Akio Fuwa

"Owing to their extremely high toxicity in the environment, the dioxins have been attracting social, technical and scientific attention in recent years. The authors theoretically had predicted the thermodynamic properties of all the dioxins via quantum chemistry and statistical thermodynamics and elucidated the generation-decomposition behavior of dioxins in the equilibrium calculation· of C-H-0-Cl system. In actual combustion processes, it is said that metallic compounds have much influences on the dioxins behavior. The aim of this study is to reveal the roles of metallic compounds the generation-decomposition behavior of dioxins is revealed from the viewpoints of quantum chemistry. Especially, the catalytic effect of copper has been investigated for the reaction, 2HCl(g)--H2(g}+Cl2(g) and for the etherification reaction from precursors, which is Phenol(g) here, to dioxins. The catalytic role of Cu is shown to have much influence on the generation -decomposition of dioxins.1. IntroductionIt is well known that dioxins are very harmful not only for our health but also for that of our children and grandchildren because they are very stable substance and their reaction rates of decomposition are considerably low. On the other hands, it is not well know how dioxins are generated and decomposed; the generation-decomposition conditions and paths as well as the catalysts to decompose them'1l. The authors believe that the thermodynamic and kinetic study of dioxins is useful to find a solution to these issuers. The authors have been investigating the following problems to reveal the generation-decomposition behavior of dioxins; (a) the prediction of the thermodynamic parameters of dioxins (2), (3), (b) the generation -decomposition behavior of non-chlorinated dioxins by the thermodynamic equilibrium calculations in C-H-O system(4) and (c) the generation-decomposition behavior of dioxins by the thermodynamic equilibrium calculations in C-H-O-CI system(5). Summaries of these thermodynamic researches are as follows.(I) The thermodynamic parameters for dioxins, which had been unknown and/or inaccurate'6 l, could be predicted and are available within the scientific accuracy."

Jan 1, 2000

By K. B. Shedd

Questions regarding possible adverse health effects from exposure to zeolites arose when the inhabitants of two villages in Turkey were found to have high incidences of mesothelioma, a disease generally identified with exposure to asbestos. No asbestos deposits are known in the area, but some fibrous zeolites have been found. Further investigations have resulted in conflicting opinions as to whether fibrous zeolites are related to the high incidence of mesothelioma in Turkey. The U.S. Department of the Interior, Bureau of Mines examined the habits of domestic zeolites by scanning and transmission electron microscopy. Only erionite and mordenite particles possessed acicular to fibrous habits. With the exception of a rarely occurring woolly erionite sample, the fibrous zeolites were not dimensionally equivalent to asbestos.

Jan 1, 1982

By Kazuyuki Kakegawa

The sintering characteristics and the change in the compositional distribution in the PbTiO3 PbZrO3-Pb(Mgl/3Nb2/3)O3 system during the sintering process by spark plasma sintering (SPS) method were examined. They were compared with those by a normal sintering method. The densification by the normal sintering was slow even at high temperatures, When SPS method was employed, much lower temperature and shorter period resulted in sintered bodies having almost the theoretical density. As expected in normal sintering, the compositional distribution decreased as the sintered density increased. On the contrary, the change in the compositional distribution by SPS was much smaller than that in the normal sintering. This sintering characteristic of SPS suggested a possibility of fabrication of sintered material having a desired compositional distribution.-

Jan 1, 2003

By Shengli Wu, Mingyin Kou, Laixin Wang, Zhe Wang, Xinliang Liu

The sticking behavior of iron ores in the shaft furnace is one of the most important problems in the COREX melting progress, which directly influence the smooth operation and productivity of shaft furnace. Therefore, it is of great importance to study the sticking behavior of pellets in COREX shaft furnace. The results showed that porous metallic iron produced at the interface of pellets samples was the main reason for the sticking of pellets in the COREX shaft furnace. The SI (sticking index) and metallization rate increased with the reduction temperature and gas flow, and decreased with melting rate. However, the SI of pellets in the COREX shaft furnace could be decreased by the proper match of melting rate and reduction temperature, reduction temperature and gas flow, while the metallization rate of pellets were kept at a certain level. Furthermore, the matching of melting rate and reduction temperature was more effective than the matching of reduction temperature and gas flow.

Jan 1, 2016

By Kimiaki Utsunomiya, Yasumasa Hattori, Yoshiaki Mori, Toyokazu Okubo

"The effect of various operating conditions on splashing behavior in a Peirce-Smith converter has been investigated with a 1/5.7 scale cold model. Dynamic similarity between the model and a commercial converter was attained by setting the modified Froude number in the model experiments in· the range for normal converter operation. It is known that for a given modified Froude number the dimensionless penetration length of gas into the liquid phase increases as the liquid density decreases. Moreover, penetration· length has a large effect on splashing behavior. Therefore, a heavy liquid, a mixture of water and lead concentrate was used as the liquid phase. It was concluded that the amount of splash dramatically decreases with a reduction in the buoyancy energy per, unit liquid mass and an increase in the horizontal distance between the tuyere tip and the edge of the mouth.IntroductionSubmerged gas injection is widely used in practice in ferrous and nonferrous pyrometallurgical operations to achieve large gas-liquid contact areas and good agitation of liquid for rapid chemical reaction. The common application in ·nonferrous industry is the Peirce-Smith converter with multi-tuyere for copper and nickel matte converting. This process has been used for over 100 years because of its effectiveness in mixing of the molten bath, as well as its merits of the engineering simplicity. However, the mechanisms which · determine the blowing performance is poorly understood, and the design and operating conditions of the Peirce-Smith converter varies widely from plant to plant, such as by diameter, length, mouth angle, tuyere position and level of molten matte. Smelters have continuously made an effort to increase converter productivity, implying maximum tuyere blowing rate. Above a certain critical blowing rate, splash of molten matte from the converter mouth becomes unacceptable because of dangerous ejection and accretion buildup around the converter mouth, which results in interference with effective hood sealing. In fact, a 1993 converter survey[!] reported that splash was a major limiting factor for blowing rate and 54% of responding plants from around the world regard it as a limiting condition[2]. In order to increase tuyere blowing rate a study of the effect of various operating conditions on splashing behavior is expected."

Jan 1, 2000