Search Documents

By E. R. Phelps

It is very seldom that a completely new project is initiated. Most projects consist of a new and different combination of proven techniques or a combination of proven and new techniques. The theme of my discussion today falls in the second category. Proven methods of water transportation and proven methods of bulk material handling were combined with some new techniques which resulted in a new market for the coal industry and a cheaper fuel supply for the power industry. In this respect I refer to the water transportation of coal from the West Kentucky coal fields to coal burning power plants on the west coast of Florida. Peabody Coal Company, Florida Power Company, Gulf Coast Transit, and Mid-South Towing combined their individual requirements and "know how' to make this project possible. I feel the results speak for themselves since it proves that coal can be mined in the West Kentucky coal fields, transported some 1,200 miles by river barge and some 450 miles by ocean going barges, be delivered to power plants on the west coast of Florida and still meet the competitive prices of gas and residual oil. The unique parts of this project concerns the storage and trans loading facilities for coal from river equipment to ocean equipment near New Orleans; the return haul of phosphate and it's trans loading from ocean to river equipment at the same facility and the use of large ocean going barges. In detail it works as follows: Coal is mined in West Kentucky and loaded into 1,500 ton river barges on the Green River. It is then transported some 100 miles to the mouth of the Green on the Ohio River, then 200 miles down the Ohio to it's convergence with the Mississippi, and then 900 miles down the Mississippi to the trans loading facility some 40 miles South of New Orleans. There it is transferred from the 1,500 ton river barges to 18,000 ton ocean going barges and hauled some 450 miles across the Gulf of Mexico to the Gannon Station of Tampa Electric at Tampa entailing a total haul of approximately 1,650 miles.

Jan 1, 1966

By Muhammad I. Kabir

A new minitest of in situ uranium leaching processes at reservoir conditions is proposed. The test which consists of a single observation/ production well and two observation wells is designed to permit the evaluation of both restoration and leaching parameters. It is shown that by using a straight forward history matching procedure, sometimes called a type curve analysis, both the rate of leaching and the ultimate uranium recovery can be evaluated based on the results of the test. Type curves are presented for the case in which the reaction rate is kinetically controlled and there are no other minerals competing for oxidant. Other situations can be approached using the same techniques as those presented here.

Jan 1, 1981

By W. C. Meyer

A physical model of flotation, derived from viewing froth as a kinetic species since it constitutes the carrier of ore particles, not only agrees with and is simulated by engineering math models, but is statistically verified by actual laboratory flotation data. The model couples the mechanical removal of froth using paddles with the more rapid chemical interactions taking place in the bath. It clearly shows that the kinetics of mass removal is dictated by flotation cell dimensions, paddle speed, and, more importantly, froth characteristics. Some conclusions and predictions of the model are presented.

Jan 1, 1982

Coal-derived flue gases contain CO2/SO2 and these contaminants preferably have to be captured by cheap sorbents. This remediation approach is from the standpoint of addressing issues such as global warming, acid rain and development of Advanced Power Generation Systems and to realize the economic gain as well. Conventional and existing dry scrubbing technologies use regenerable sorbents which are pollutant specific and require expensive stabilizers in order to attain versatility. This paper discusses the use a novel class of sorbents prepared from the heavy metal contaminated Berkeley Pit water (Butte, Montana) by a proprietary process developed at The University of Nevada, Reno. These sorbents are activated mixed spinel ferrite (MxFe,_X04)' Preliminary experimental results show that the sorbents have good desulfurization and CO2 decomposition capacities. The decomposition effectiveness of these mixed spinel ferrites was studied at 300°C and compared against the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The results indicated that the mixed spinel ferrite had good affinity for the adsorption and decomposition. The CO2 decomposition data of both sorbents fitted the first order reaction kinetics. Even though the surface area of the magnetite was higher than that of mixed spinel ferrite, the CO2 decomposition rate of the mixed spinel ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO2 was 100% decomposed into carbon and other carbon! hydrogen compounds by the mixed spinel ferrite whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was 3-5 times more efficient than magnetite.

Jan 1, 1996

By James W. Echerd

Anthracite preparation developments, particularly in the early days of the anthracite industry, formed the basis for the modern coal preparation plants that have become so essential to the coal industry today. The anthracite industry, from early in the 19th century until relatively recently, was a leader in mining, preparation and marketing of coal, and played a leading role in the development of the industrial America we know today. Anthracite was discovered in America in about 1760--the story of Necho Allen is well known--but the rediscoveries leading to mining operations took place about 50 years later. The Wurtz brothers in 1815 at Scranton, the Smith brothers at Wilkes-Barre in 1807, Beach in Hazleton in about 1814, and Boyd in 1816 at Shamokin were all instrumental in promoting early mining and marketing of anthracite (J3. The early canals and railroads were built for the specific purpose of moving anthracite to the market areas. Eventually, the industry grew until, in 1917, it reached a production zenith of a little over 100,000,000 tons, representing about 20 percent of the total coal output in the United States. Almost half of the anthracite produced that year was consumed for domestic heating, a utilization that had dominated the industry for almost 100 years. Initially, anthracite had to be used by gunsmiths and blacksmiths, after which had followed the consumption of extensive quantities for railroads, blast furnaces and foundries, and electric power generation. Most of the markets have been lost to coke, oil, and natural gas. Near the anthracite regions, however, significant quantities are still used for domestic heating, power generation, carbon black manufacture, blending with bituminous coal to make metallurgical coke and fuel, and for other industrial purposes. Thus, anthracite production has not been entirely committed to history, but remains an active industry that follows modern practices in the mining, preparation, shipping, and utilization of a fuel that is still a valuable adjunct to the national economy. In fact, its inherent low sulfur content may make it an important fuel of the future. Estimates indicate there are reserves of anthracite to last for 300 years at a consumption rate of 50,000,000 tons/year. Anthracite Preparation Yesterday A 170-year history of the anthracite industry obviously is not the purpose of this discussion. A complete history of anthracite preparation, the rather unglamorous step in the processing of "mine run" hard coal to make it suitable for the user, is also not practical. Hence, the purpose of this report is to trace the development of some of the most important processes used through the years to meet a part of the demand for energy developed by our modern society. Anthracite preparation in the early days of the industry consisted solely of separating slate from the coal, by hand, underground (Z). This method prevailed for almost 20 years until wrought iron hand rakes were introduced to separate the large and small sizes. Shortly thereafter, the first attempts were made to size and clean the coal aboveground. The coal was dumped on a perforated cast iron plate, and men used sledge hammers to break the larger pieces into smaller sizes suitable for the market. The smallest sizes--that is, the material that went through the plate--were thrown away because they had no value at that time--a concept that existed for many years and actually was the basis for the subsequent "river" coal production and the many silt banks which are landmarks in the anthracite region. The larger sizes, at that time, sold for 50 cents per ton. The Batten breaker, or roll crusher, was invented in 1844, followed soon thereafter by the Snell-Diehm breaker (A). The latter had disadvantages, including excessive waste and fixed product size, but it later was improved in these respects. A breaker was also developed at Minersville, Pa., at about the same time that processed 200 tons of coal per day, using roll crushers and circular screens (1). Handpicking, from the beginning of anthracite preparation, was an important part of the cleaning process and was still being practiced as late as 1950. It was this process that involved the "breaker" boys of coal region lore. How much good handpicking accomplished depended on how much impurity was present in the coal--the more the impurities, the greater the reduction in ash. Thus, high-impurity streams were significantly improved, whereas picking of relatively clean coal was mainly to show an effort to make a quality product. As indicated, picking is largely a visual operation. It was and is wasteful of coal in the larger sizes since some good coal is always associated with the bad. However, it was probably much more effective' in the larger than the smaller sizes.

Jan 1, 1971

By S. Tuylu, D. Adiguzel, A. Bascetin, H. Eker

"Tailings can be more stable in-site where they are stored and and so the risk of conventional tailings dam accidents can be reduced by alternative methods. In recent years, surface paste disposal (SPD) method is one of the alternative tailings storage methods. According to the results obtained from the previous lab scale experiments, optimum storage design was determined and then, this design was carried out in-site application under atmospheric conditions by a pilot scale tests. In the field study, two separate dams with no environmental hazards were established by the hazardous waste storage directive, whose surface area is measured as 400cm × 200cm. Also physical changes in the paste tailings were measured by the sensors such as volumetric water content, mutric suction and oxygen consumption. In addition, seepage water was collected in the drainage pool and examined for acid mine drainage and metal mobilization risks. As a result of the preliminary data obtained from measurements of pilot scale tests, when the pH value of seepage in the cemented dam (only 1th and 10th layers with cemented) is about 11, the pH value of seepage in the uncemented (reference) dam is measured at 8-9. INTRODUCTION Environmental damages occurred during the deposition of mine process tailings at surface using conventional methods (tailings dam etc.) can be reduced and/or eliminated with the use of new technologies and methods to an important extent. Nowadays, it has been investigated to safely deposit metal mine wastes generally discharged into surface tailings dams, seas, rivers, creeks etc. using Paste Tailing Technology which gains the growing importance in recent years. Meanwhile, Paste Tailings Technology has two applications in industry as an underground paste backfill and surface paste deposition. Particularly scientific studies about deposition of process tailings as paste sample in underground and surface have been increased. These studies showed that surface paste deposition can minimize the free water amount which is the biggest problem in conventional tailings dams. Additionally, it also provides less particle segregation, in other words, the formation of more homogenous material, the development of geotechnical properties which causes to obtain more stable material, increases the strength and stability of the paste with addition of binder where necessary surface paste material, and reduces the risk of Acid Mine Drainage (AMD) (Bascetin et al., 2017a). Theriault et al. (2003), Martin et al. (2006) and Simms et al. (2007) reported that Bulyanhulu mine in Tanzania is the first gold mine to employ surface paste disposal (SPD) worldwide. Here, tailings are deposited alternately via several towers. The tailings flow away from each tower to forming a conical deposit. Each layer had a lower thickness than 30 cm. The fresh tailings were poured on top of drying and hardening layer after a waiting period of 5-30 days. No cement was added into the tailings to prepare paste material. Uncemented paste was deposited by a solid content of 73% which corresponded to a 250 mm slump cone height (Yilmaz et al., 2014). In a study conducted by Yilmaz (2010) illustrates the preliminary results of a field cell testing undertaken to investigate the effect of in situ climate conditions and material properties on the performance and quality of fine-grained, sulphide-rich paste tailings at the LaRonde mine in Quebec, Canada. A total of two field cells are constructed in the surface disposal site of the mine and categorized as cemented cell CC and uncemented cell UC (Bascetin et al., 2017b)."

Jan 1, 2018

By R. G. Church

Belle Ayr Mine was established in 1972 as the first large surface coal mine in the Powder River Basin of Wyoming. During the mid-1980s, it was eventually out-distanced in productivity by newer mines, and management recognized that the mine must recapitalize its major mining equipment and enhance its workforce flexibility in order to be competitive in the deteriorating market situation. Therefore, state-of-the-art haulage and loading equipment was placed into service, and a 12-hour rotating shift and a technician-based workforce was implemented. Belle Ayr Mine is located 29 km (18 miles) southeast of Gillette, Wyoming, in Campbell County (Figure 1). The mine is a part of AMAX Coal West, Inc., and with its sister mine, Eagle Butte, located 8 km (5 miles) north of Gillette, is a major contributor to the overall coal production of AMAX Coal Industries, Inc., headquartered in Houston, Texas. This paper addresses mine planning, recapitalization initiatives, and innovative workforce changes which propelled this large, surface coal mine to the forefront of productivity in the ever tightening low sulphur coal market.

Jan 1, 1994

By W. Moser

During the ten year span from 1978 to 1987, the number of fires which occurred in under-ground coal mines doubled from the previous ten years. Anyone involved with underground coal mines is well aware of the associated tragedy that can result from these fires, both to personnel and to property. Every day mine management and mining personnel face this threat of a possible mine disaster or fire. Their ability to deal with such a situation safely and effectively depends on the level of emergency preparation developed and maintained. As a direct result of the ever-increasing interest in the Mine Emergency Preparedness Program and the Mine Fire Training Programs currently being conducted, the Emergency Preparedness Center was created. As a branch of the Mining Extension Service at West Virginia University, the Center provides preparedness training at several different levels on a varying range of topics. Classes are conducted at a new especially-designed training laboratory at the National Mine Safety & Health Academy in West Virginia. By maintaining the proper equipment and levels of training allowing for immediate response, the personnel who are part of the Center believe that the impact of a mine fire or other such emergency situation can be minimized. This paper will present recommendations for maintaining an efficient mine emergency preparedness program and will provide information regarding the Mine Fire Training Program as conducted by the Emergency Preparedness Center and describe the advantages of the newly constructed training facility.

Jan 1, 1993

By Rajat Gangrade, Haotian Zheng, Jarrett Smith, Daniele Nebbia, Mike Mooney

The application of artificial intelligence (AI) to improve tunnel boring machine (TBM) operations requires a significant amount of information to train robust performance prediction models, e.g., for tunneling-induced settlement, productivity, tool wear, etc. This paper presents the AI framework applied to the North-East Boundary Tunnel (NEBT), the largest component of the Clean Rivers Project in Washington, DC. The paper focuses on required elements for real-time AI use to estimate tunneling-induced ground and building deformation and cutter tool wear. Keys to the framework include defining the necessary quantities of data required as well as the process of windowed training, validation and model testing. To date, the models developed for ground deformation and tool wear show satisfactory performance when compared to observed field observations during tunneling.

Jun 13, 2021

By A. Taghavi, I. Hassan, A. Solecki

"The Eglinton Crosstown Light Rail (LRT) Project is part of an $8.4 billion investment to expand transit in the Toronto, Canada area and is the largest transit project initiated in Province’s history. Settlement control and impact to over 1400 adjacent structures due to tunnelling was identified early as a critical project risk. The ground conditions along the 10km tunnel alignment consist of water bearing soft ground deposits (clays, sands, silts) which required careful analysis and control during design and construction. This paper will describe the process used to analyze settlements along the numerous of adjacent structures and evaluate achieved settlement results to those used during design. The paper will demonstrate that with the appropriate design specifications, selection of modernized EPB machines, and contractor performance, settlement can be maintained well below typical industry (volume loss) standards, expanding the application and suitability of soft ground tunnelling in sensitive settlement areas. INTRODUCTION The Eglinton Crosstown Light Rail Transit (LRT) Project is part of an $8.4 billion (2010$ CND) investment from the Ontario provincial government to expand transit in the Toronto, Canada area. The project is being developed by Metrolinx, an agency of the Government of Ontario to provide 19 kilometers of dedicated LRT service connecting the City of Toronto from the west to east along Eglinton Avenue. Upon completion in the year 2020, the Crosstown will be the first LRT constructed in Toronto. It will link regional and local transit, cut travel time along the route by half and provide over a thousand jobs during construction."

Jan 1, 2016

By H. Dho

The role of sodium silicate in the anionic flotation of a Florida phosphate ore was investigated using laboratory continuous flotation tests, frothability tests and SEM observations. In the absence of sodium silicate, Ca++ promoted the unwanted activation of quartz by forming calcium bearing precipitates. The addition of sodium silicate enhanced the flotation efficiency through: (1) the removal of impurity minerals and calcium-bearing. precipitates from quartz surfaces by dispersion, (2) drier and more persistent froths stabilized by oily droplets containing calcium silicate precipitates, and (3) higher specific flotation rates of phosphate relative to quartz, leading to faster flotation rates and increased selectivity of separation.

Jan 1, 1990

By Stanley Noss

One need be neither an historian nor technologist to recognize that activi¬ties related to the conversion of coal to other usable energy forms have been active for nearly fifty years. The degree of such activity and its evolution to significant commercial proportions has, however, fluctuated widely with world circumstance. For the past decade there has existed both a consistent technology evolution effort in classic R & D proportions, and a mainstream commercial acti¬vity but in rather modest proportions when viewed from the vantage point of world energy needs. But the chain of events wherein it became increasingly obvious that we were in energy trouble irrespective of world politics, spurred alternative energy source activities in the fossil fuels areas. The oil embargo of 1973-1974 made the obvious even more so and provided additional emphasis for the need of such alternatives. Yet the preponderance of these added expenditures and activities (with one notable exception which is the subject of this discussion) has been focused on the intended identification of the best or ultimate process by means of analytical and modest empirical means, whereas our circumstance dictates a bold, higher-risk effort to prove the viability of coal conversion as an industry on a real-time, real-size, real-economics basis. With such proof on hand, industry demands in all related areas will provide the stimulus, motivation and environment for all processes. There is both need and room for many who will compete for a meaningful segment of this new industry which can grow at a rate never seen before in our growth history. The single program in the world today oriented specifically toward the goal of proof of industry viability is the Energy Research and Development Administration's CBF (clean boiler fuels) Program for which COALCON is proud to be the prime contractor.

Jan 1, 1976

By David N. Hedges

This paper discusses the actual recovery and installation of a longwall in a bituminous coal mine in Western Pennsylvania. The coal bed mined is in the Lower Freeport seam which averages 42 inches (1.07m) in height locally. Drainage from the mine is approximately 3.5 million gallons of water per day (13.25 million liters per day). This water deteriorates the mines predominately fire clay bottom making it extremely difficult to move equipment. Support removal is accomplished by pulling the 6 ton (5443 kg) shields out under their own hydraulic power and transporting them by track over four miles (6437m) co the next longwall panel. This paper also discusses the changes that will be made to aid in the succeeding longwall recoveries and installations.

Jan 1, 1984

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By J. M. Duke

Significant resources grading less than about 1 % nickel occur in magmatic sulfide deposits of two types. In the Mt. Keith type, extensive zones of disseminated nickel sulfides occur in the central portions of certain synvolcanic dunite-peridotite sills of komatiitic affinity in Archean greens tone terranes. In the Duluth type, disseminated copper-nickel sulfides occur near the basal margins of intrusions of flood basaltic affinity associated with intracontinental rifting. In both types, the parent magmas became saturated with sulfide following the onset of fractional crystallization and the separation of the immiscible sulfide melt was accompanied by the precipitation of a relatively large proportion of silicates. The abundant silicate crystals impeded the coalescense and accumulation of the sulfide droplets with the resulting formation of large but low grade deposits.

Jan 1, 1982

By Lake H. E.

The request to participate on your theme panel was accepted with some reluctance but indeed as an honor. My subject was outlined to cover 'Energy Resources - both nuclear and conventional' as related to your theme 'Minerals - Treasure Trove of the West'. This is indeed quite an order and I hope you will forgive me for concentrating mainly on the nuclear-uranium portion with brief references only to conventional fuels some of which will be covered in detail later in your conference. In regard to Uranium, I am speaking on the fringe of the area containing half the uranium reserves in your country and no doubt to many who are very conversant with knowledge of these resources. Nevertheless since our two countries have been very closely allied in both nuclear developments and uranium supplies I hope an exchange of information may be mutually beneficial. Concentration on the nuclear fuel resources is I hope understandable as nuclear energy is the coming source of power which will augment the rapid demand in the industrialized countries and provides hope for economic power in many of the more underdeveloped countries. The situation regarding conventional fuel resources is more widely known and their expanding future revolves around production cost reductions, research into diversified uses, plus more assurance of imports from countries less effected by international controversies determining export policies.

Jan 1, 1967

By Alex Stewart

Most iron bearing ores treated by the R=N Direct Reduction Process yield products lower in phosphorus than the initial ores. The sulfur is also removed and generally is in the range of 0.02 to 0.05 percent in the final R=N product, independent of the sulfur content of both the ore and carbon fuel used. The mechanism and thermodynamic justification of the principal reactions leading to the removal of both phosphorus and sulfur and the control of sulfur in the iron concentrate produced are discussed and supported by the results of laboratory experiments. In substantially all iron ores (containing up to 4% sulfur as sulfate) and solid carbon fuels (containing sulfur from 1 to 8%) tested, the rejection of sulfur has been in the order of 90-95%, with not more than 0.02 0.05% sulfur in the final metallic iron product. With respect to phosphorus-bearing iron ores ranging up to 0.70% P205, the rejection to tailings has been in the order of 70-95%, resulting in not more than 0.03 - 0.07% phosphorus in the final product.

Jan 1, 1958

By J. Le Gac, P. Zettwoog, J. Brenot, J. W. Piechowski, J. C. Nenot

INTRODUCTION The components of the radiological hazard in uranium mines are: 1. exposure to radon and its short-lived daughters 2. exposure to long-lived ore dust 3. external irradiation With usual ventilation rates, the dosimetry relative to the first component only requires to know each miner&apos;s exposure to a potential energy of short-lived radon daughters, (EXP[a]). Presently in France, (EXP [a]) is determined monthly from radon concentration measurements. This is an indirect method based on ambient monitoring. After technical improvements achieved during the last years it is now possible to measure (EXP [a] directly with an individual portable monitor developed by the CEA. The purpose of this study is to analyze and compare monitoring results obtained by these methods. DETERMINATION OF INDIVIDUAL MONTHLY EXPOSURES TO[ a] POTENTIAL ENERGY OF SHORT-LIVED RADON DAUGHTERS [(EXP a) amb, by ambient monitoring] In this case, it is necessary to know individual monthly exposures to radon, (EXP Rn). As mentioned by Pradel, J.,et al., 1976, (EXP Rn) is estimated for each worker from informations both on radon concentrations (CRn) measured as described by Pradel, J., 1962 and times (t) elapsed in the various workplaces. (EXP Rn) is obtained by summing up the elementary radon exposures CRn x t relative to all the workplaces where the miner was successively engaged during the month. (EXP Rn) values are then corrected by an average equilibrium factor of 0.17 deduced from many measurements and taken as representative for all the French mines. Finally: [ ] (EXP [a])ind are obtained directly with an individual portable instrument described by Chapuis, A.M., et al., 1972. Samples of the air breathed by the miners are pumped continuously and radioactive aerosols containing the short-lived radon daughters are trapped on a filter. The principle of the measurement lies on track-etch detection of the a particles emitted by the deposited material. The technical aspects have been described by Duport, P., et al., 1980a, Mouden, A., et al., 1980 and Chapuis, A.M., 1980. As mentioned by Duport, P., et al., 1980, fiability is good. Indications on measurement reproducibility are given by Pradel, J., et al., 1977. PRESENTATION OF THE STUDY The underground miner population of a French mine was followed during a period of 8 months (October 1978 - May 1979). Monthly exposure values for each miner determined either by ambient or individual monitoring, (EXP [a])amb or (EXP[ a])ind, had been previously collected by Le Gac, J., 1980, who had also defined miner categories according to the characteristics of the work performed. Four groups are considered here, the "whole mine" and three categories as described in table 1. Data on the individual monthly exposures,(EXP [a])ind and (EXP [a])amb, were taken again to analyze the individual cumulative exposures instead of the "month by month" values. The influence of the mean habits of each individual on its surveillance results is thus taken into account. Each miner has a cumulative exposure as an individual of the "whole mine" and as an individual of each category in which he has worked. The results obtained by ambient or individual monitoring were analyzed (characteristics and adjustements of the distributions) and then compared (description of the discrepancies observed). Obviously, such a study is possible only if all the exposures are cumulated on a same duration. As miners have not worked during the same number of months in the course of the data collecting period, one must considerer the individual average monthly exposures, [(EXP a)]amb and[ (EXP a)]ind, instead of the individual cumulative exposures, which is typically the same thing. To be sure that the exposure values of a given group (A, B, C or D) are representative, only those miners really present for at least 3 months in this group were taken into account. Finally, each individual of the "whole mine" and of the various work categories has a pair of average monthly exposure values : [(EXP a)amb] determined by ambient monitoring and[ (EXP a)ind] deduced from the track-etch recording of the individual portable monitor. Let a miner be engaged during n months[ (3 < n < 8)] in a group, the following relations then apply : [ ]

Jan 1, 1981

By Rodolfo V. de la Cruz

The in-situ deformability of a highly jointed basalt rock mass was determined by two distinctly different methods: one, by the NX- borehole jack method where the displacements of opposing curved platens were related to the applied hydraulic pressures, and; two, by the modified Goodman jack method where the tangential strains on the borehole walls were related to the induced tangential stresses. The modulus obtained by the modified Goodman jack method were much higher than those obtained by the NX- borehole jack method. To explain the discrepancy, the influence of fractures and test variables such as depth, orientation, hole number and applied pressure on the calculated modulus of the rock mass were analyzed by factorial analysis and it was found that the orientations and depths of measurement has statistically significant effects. The in-situ deformability values obtained by non-linear regression analysis were also found comparable with other measurements and empirically predicted values for the basalt rock mass.

Jan 1, 1982

By Aliakbar Golshani, Behnam Eslami

"Surface settlement adjacent to sensitive structures is a challenging issue in the tunnel engineering. In this study, 3D simulation of TBM excavation has been performed with the FLAC3D code and then the results compared with real monitoring data. Sensitivity analysis was carried out for all parameters affecting the surface settlement, such as the tail void grouting pressure (Pt), the face pressure (Pf), the tunnel diameter (D), overburden (q), shield thickness (t) and the length of the shield (L). The results show that the face pressure, tail void grouting and tunnel diameter have a considerable effect on the maximum ground displacement.In this paper, the monitoring data from Mashhad Metro was used to verify the numerical simulation. Data monitoring for about 47 sections between A2 and D2 stations was selected and a multiple regression analysis was performed. Based on this analysis, an empirical relationship was obtained for the coefficient of regression relationship which confirmed the sensitivity analysis.INTRODUCTIONThe surface settlement due to tunnel excavation is a complex issue, since the surface displacement is a function of several parameters that they are related to the excavation method, soil characteristics and TBM elements. Prediction of deformation is a very important issue, especially in urban areas, since these displacements may be affected the superficial structures. In recent studies, one of the most popular empirical relationships that is used to predict the surface displacement has gussian curve that it was suggested by Peck [1, 2]. An analytical relationship was proposed by Chow that its base assume was isotropic of soil, that surface settlement can be estimated based on the tunnel geometry and the shear modulus(G) [3]. Besides these methods numerical approaches such as the Finite Element Method (FEM) and the Finite Difference Method (FDM) have been used over the last twenty years, since numerical modeling has a high capability to simulation a complex soil conditions and irregular geometry [4]. In this study, all aspects of the EPB-TBM on Mashad Metro Line 2 were modeled and the most important influences on surface displacement in urban areas were determined [1, 3]."

Jan 1, 2016