Search Documents

By D. R. Spears

Conventional round tank thickeners have been widely used in the mining industry for many years. The mining industry was well satisfied with the ability of conventional thickeners to improve minerals beneficiation operations. However, development of improved flocculants (the polyacrylamides) made possible much more rapid settling rates, since polyacrylamides produce large flocs rapidly (unlike starch or inorganics). Traditionally considered to be a slow operation if maximum underflow density was achieved, and therefore there was some justification for the expense. Thickeners required large volumes to permit sufficient time for settling. The oversize not considered a drawback but the initial capital cost was. In high rate thickeners, a bed of thickened material is allowed to build around the feedwell, even above the bottom of the feedwell. The slurry is fed directly into the bed at a velocity that allows the material to be evenly dispersed over the thickener area This more efficient use of settling area allows a higher solids throughput per unit surface area (rise rate). In this paper, high rate thickener rise rates and polymer consumption are compared.

Jan 1, 1998

By Michael P. Connor, O&apos

The Wing Hill Garnet Deposit, located near Rangeley, Maine, forsed through assimilation of Early Paleozoic metasediments by an intrusive Devonian gabbro. The resulting ore body is exceptionally large and high-grade, consisting of 50-70% almandine garnet. Following open-pit quarrying, the ore is trucked to Industrial Garnet Extractives' mill in West Paris for final processing. Two grades of abrasive are produced - a pure, premium grade INDUSTRIAL GARNET and the Lower grade co-product IGE UTILITY GRIT, both of which are available in a variety of sizes. INDUSTRIAL GARNET is marketed world- wide into a diverse marketplace including both loose grain and bonded applications.

Jan 1, 1985

By Donald H. Dowlin

The design of a preparation plant for minimum maintenance and clean up requires both the skills of the Engineer and the practical experience of the Operator. From the initial flow sheet and preliminary design until the plant is completed and operating, each phase of the work must be thoroughly explored for simplicity, workability and high efficiency. It is the responsibility of the Designing Engineer to develop the plant around the basic flow sheet, selecting equipment and materials not only with regards to Initial cost but also required upkeep and repair.

Jan 1, 1962

By Drew Bazil, David Smith, Matteo Ferrucci, David Pittman

The Gateway program will provide additional rail capacity between New Jersey and Manhattan. This paper describes how a 70-foot-deep section of cut and cover tunnel was designed to directly support future high-rise towers. The tunnel will link previously completed tunnel sections under Hudson Yards to future tunnels under the Hudson River. The design aims to minimize constraints on future overbuild and future tunnels, while maximizing constructability within a small worksite. The tunnel will pass under the High Line elevated walkway, next to an active rail yard, and close to a subway tunnel. The design was developed by a tri-venture of WSP, STV and AECOM. WSP led the design of major underground works; STV designed utility relocations and the underpinning concept for the High Line; and AECOM designed temporary in-tunnel systems. Construction is expected to start in 2023.

Jun 13, 2023

By Louis W. Towle

A brief history of the use of Ammonium Nitrate in explosives and blasting agents is given. Methods of manufacture and physical properties of the various types of Ammonium Nitrate are given with particular reference to their use in blasting agents Important properties of blasting agents discussed are sensitiveness, methods of initiation, velocities of detonation, strength, density, products of detonation, rate of pressure development, and borehole pressure.

Jan 1, 1959

By Ray A. Rothrock

The in situ mining of uranium is the process whereby chemical lixiviant is injected by means of wells into, and flowed through, an ore body. The lixiviant reacts with uranium which has been previously oxidized making the uranium soluble. The solution is then brought to the surface by means of producing wells. In situ mining disturbs the ground-water quality in the immediate area. Since ground water is a natural resource used by man, care must be taken not to allow the lixiviant to escape the local mining area. Also, when the ore body is mined out, the area should be restored to as near its original state as is reasonably achievable. The return of ground-water quality to its original state can occur naturally over a long period of time or be enhanced using appropriate technological means.

Jan 1, 1981

By Bruce F. Bohor

Silica sand has been mined in Illinois from the St. Peter Sandstone since the turn of the century, especially in the area around Ottawa on the Illinois River in the north-central part of the state. Production of this sand, consumed mainly by the glass and foundry industries but also sought after for many other uses, has grown with the economy, and last year's output in Illinois exceeded 4,000,000 tons. Such an important commodity was given the early attention of the Illinois State Geological Survey, and a very complete report was issued in 1928, authored by J. E. Lamar. The mining and processing of the sand has changed very little during the intervening 40 years, so that much of Lamar's data and descriptions are applicable today. More recently, the stratigraphy of the St. Peter Sandstone in north-central Illinois has become better known from the work of Willman and Payne (1942). The present authors have borrowed generously from Lamar's publication, and we wish to acknowledge the contribution of both of these studies to our work.

Jan 1, 1969

By Bruce A. McKinstry

Introduction For many major mining projects the time frame from initial planning to production can be measured in decades. Hecla's Silver Shaft project, scheduled to go into production by the end of this year, includes a complete surface facility, shaft with an ultimate depth of 2.4 km (7,700 ft), complete ore pass and loading pocket system, and 610 m (2,000 ft) of development drifting and stope preparation. The project was conceived in the fall of 1979, and the duration of a mere four years from conceptual engineering to production is testimony to what can be accomplished when a mining company and a contractor work as a team rather than developing into two warring camps, as often happens. Engineering In 1979, Hecla Mining Co. awarded a contract to J. S. Redpath Corp. to perform feasibility investigations and design engineering related to a proposed new shaft facility at the Lucky Friday Mine. The Lucky Friday, in Mullan, ID, is a major producer of silver, as well as significant quantities of lead and some zinc. In late 1979, stoping was in prog-

Jan 10, 1983

By Kenneth R. Hancock

The importance of "Mineral Pigments" can best be shown by noting that the world production is estimated to be in excess of 47 billion kilograms (52 million st). This quantity if pack- aged in the common 22.6 Kg (50 Lb.) bag and placed end to end would circle the world over 500 times. This world production figure is based on a broad concept that pigments, extenders, and fillers have essentially similar functions. In this paper mineral pigments are products produced synthetically or from selected minerals and through pulverization have characteristics of pigments.

Jan 1, 1985

By Björn Johansson

"SUMMARY Every tunnel designer has to consider the power of water ingress when designing a new tunnel. Either you choose solutions with simple methods to divert the ingress water or a robust system with the intention that it will give gain on low maintenance costs and a long lifetime. This article describes a new method to divert ingress water in a robust way and more economical than traditional concrete lined tunnels. This system is based on a bolt grid suspending a water tight membrane, which is reinforced and covered with sprayed concrete. The method has been in limited use in Sweden since 2005 and with continuous improvement, still going on, it is now applied for the large project “Stockholm Bypass”, a 21km long highway project. TUNNEL MAINTENANCE RELATED TO WATER INGRESS The Swedish Transport Administration maintain approximately 190 various tunnels that is constructed by a number of different methods, (Swedish Transport Adm 2015). Commonly the ground conditions are good and fairly low ground support is needed. Contrary water and winter conditions can be sever, which gives high impact onto the tunnel design and in particular methods to protect against “frost and water ingress”. During a tunnels lifetime it is common that maintenance related to water ingress occurs several times and sometimes frequent occasions every year. Such maintenance costs and consequences of lost open time for the tunnel can rapidly become higher than the initial cost of the tunnel. Thereby it is obvious that spending time during design to evaluate requirements for a suitable system against water ingress is preferred. Icicles Icicles are formed when water is below freezing degrees and drips or run from an ingress point. At very cold conditions also water flows running at high velocity freeze into ice and a rapid growth can appear. If the integrity of the tunnel traffic area is interfered by icicles they urgently have to be removed before they cause an accident. Typically the tunnel or a part of the tunnel must be closed to do such maintenance. TUNNELS FROST AND WATER INGRESS PROTECTION IN SWEDEN In Sweden methods to perform “frost and water ingress protection” are primary developed for drill and blast tunnels as it is most common tunneling method. The foundation Swedish Rock Engineering Research has done a comprehensive report SveBeFo Rapport 77 that describes water and frost prevention in Swedish tunnels up to year 2005. Below is only slight description of those various methods. Lately some more attention is paid to concrete lined tunnels made by TBM since TBMs successfully built water tight tunnels in City Tunnel (Malmö) and Hallandsås Project. When environmental demands require maintained ground water levels, water tight tunnels made by pressurized concrete lining becomes more economical and on the same time also becomes protected from icicles and water drips."

Jan 1, 2016

By Carrie Smith

Along Michigan’s Upper Peninsula lies the Marquette Iron Range, home to iron mines. Just southeast of the region is the small town of Iron River, where Mary Korpi spent most of her chidhood and early adulthood. Though living in the heart of mining country, the industry did not pique her interest while growing up. As the daughter of two educators, she envisioned a different future for herself. Now, decades after working for one of the largest gold companies, she is gearing up for her term as the Society for Mining, Metallurgy & Exploration’s 2026 President.

Mar 1, 2026

By T. W. West

During the design and construction of a coal preparation facility, there are many items that can cause serious problems if not properly handled in the early stages of a project. These problems can be a detriment to smooth owner/ contractor relationships, the designing of a flow sheet, the selection of equipment, the design of the facility, the maintenance of schedule and budget, and a smooth start-up. It is the purpose of this presentation to identify some of these problems and to suggest steps that can be taken to reduce or eliminate their impact.

Jan 1, 1977

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By M. Stefanakis

Respect for the people is one of the main values of S&B. Such respect needs to be manifested by actions ensuring the bodily and spiritual integrity of personnel in pursuing their work. The ultimate target is to achieve zero accidents by developing the culture and infrastructure required to support it. Within this framework, the following proactive safety practices were introduced in 2004 and are implemented at S&B Greek sites: (a.) Management Safety Visits (MSVs) of shop floor operations to address safety attributes of work guidelines, (b.) Monitoring compliance with critical work guidelines, using a ?safety barometer? tool. The proactive nature of both above systems, facilitates communication with employees on safety behaviors and their adoption in our facilities at Milos and Fokis, has been successful. Above all, these practices corroborate the management?s concern for the people and its commitment to continuously improve the working environment.

Jan 1, 2007

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By Dennis Greene

Real-time GPS position monitoring of mining equipment is becoming more and more commonplace. Digital mining plans can now be used onboard properly equipped earthmoving equipment and excavation status is available in real-time via high bandwidth data radio systems. These systems provide a closely integrated link between operations and planning. No longer must operations wait for or be hindered by insufficient survey marks, nor is engineering delayed by lack of timely mine status information. Unprecedented efficiency gains become feasible -from the engineering office, to drilling and mucking, to reclamation, as well as in mine construction projects. Direct economic benefits of these systems will be explored as will the less tangible, but very significant, indirect operational efficiency gains.

Jan 1, 1998

By David I. Smith, Kenneth Arnold, Bryan Aweh, Vincent Falkowsk, Brian Lakin, Andy Fer

Nassau County, New York, is undertaking several projects to improve the water quality in the Western Bays of Long Island. A major step forward will be the completion of the Bay Park Conveyance Project, which will divert most treated effluent away from the Western Bays to an existing ocean outfall at the Cedar Creek Water Pollution Control Plant. The ongoing works include 3.6 miles of microtunneling, 7 miles of sliplining, 14 shafts, and a 75 MGD pump station. This paper provides an overview of the design and an update on construction progress through December 2022. The project is a collaborative effort between Nassau County, New York State Department of Environmental Conservation, the design-builder, and various consultants.

Jun 13, 2023

By Frederick W. DeVries

The following charts were presented at the Randol Gold & Silver Forum 2000, held at the Hotel Vancouver (Vancouver, B.C.) from April 18-21, 2000. It must be borne in mind that the "facts" stated and con­clusions drawn by the author were not as the result of a rig­orous technical investigation, but rather as a member of a journalistic team seeking a rapid view for presentation as news to a TV audience. Since the author's visit, some retrenchment on the part of the operators on estimating the cyanide content of the spill seems to have occurred. This does NOT alter the conclusions that (a) the spill was an intolerable embarrassment for the world mining industry, nor (b) the potential damage to future mining investments, should prompt action not be taken: 1. to understand the reasons for the dam failure, and 2. to draw up firm concepts of how to avoid future fail­ures of dams at mining properties containing materials that are toxic, environmentally unfriendly, or with as highly dis­comfiting a profile as cyanide.

Jan 1, 2000

By Jerome E. Grader

Special-purpose analog computers are being profitably applied in the process industries to perform miscellaneoas online computing functions in situations where conventional measurement and/or control hardware cannot perform a required task satisfactorily. This paper will discuss the application of such equipment in the mining industry. It is divided into two parts, beginning with a description of operation of the hardware, followed by a discussion of several applications of the computers to mining industry control problems.

Jan 1, 1969