Search Documents

By Saghar Farajzadeh, Fatemeh Kazemi, Ataallah Bahrami

Spirals, the most common equipment for the separation of heavy minerals such as chromite, are greatly affected by size distribution and the liberation degree (hence the specific gravity and size) of the feed particles. In this study, the efficiency of spirals in separation of low-grade chromite particles has been investigated by studying the distribution of grade, size distribution and liberation degree of feed, concentrate, and tailings of spiral. For this purpose, mass balance constraints were applied to the spiral-containing chromite processing circuit. Afterwards, the grade variations and size distributions have been investigated. According to the results, when the feed to the spiral has a larger size distribution, the enrichment ratio of the feed is 1.32 and, with the smaller feed size, this value has increased to 1.99. When the spiral feed has a larger size distribution and higher specific gravity, the recovery of chromite increases with increasing particle size up to 250 microns, and then with increasing particle size, recovery decreases with a relatively steep slope. Evaluation of spiral efficiency with respect to particle liberation degree has also shown that despite the high degree of liberation of spiral feed in size fractions smaller than 75 microns (88.9%), the liberation degree of spiral concentrate and tail in this faction is equal to and less than that of feed, which can indicate poor spiral performance in these size fractions.

Oct 27, 2020

By K. Osseo-Asare

LIX63 in combination with DNNS selectively extracts nickel and/or cobalt from acidic leach liquors with pH values as low as 1.0. Nickel/cobalt and cobalt/nickel selectivities are achieved by varying the relative concentrations of LIX63 and DNNS. Increasing LIX63 concentration retards both extraction and strip-ping rates while DNNS has the opposite effect. Slope analyses of equilibrium data indicate that both LIX63 and DNNS are present in the extracted complexes. Examples of possible flowsheets are presented.

Jan 1, 1978

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

Satisfactory means of managing growth in boom towns is a concern in mineral, energy and other large industrial developments. This session will include examinations of socioeconomic impacts, major issues such as social disruption, case studies, methods of managing growth, and concerns involving Indian lands. Innovative methods will be offered to assist the public, government, and industry in finding solutions to managing growth in rapidly growing communities.

Jan 1, 1979

By D. S. Flett

Abstract. The commercial importance of hydroxyoximes as extractants for copper has given impetus to basic studies on the chemistry of metal extraction by these compounds. The discovery of accelerator compounds which produce catalytic effects on hydroxyoxime extraction rates has led to mechanistic studies of these rate processes. While these studies have highlighted the importance of interfacial chemical reactions in the extraction process, it is not yet possible to unambiguously describe the mechanisms of metal extraction in these systems or the associated catalytic effects. This paper reviews progress in understanding the mechanism of metal extraction by hydroxyoximes.

Jan 1, 1979

By Quanjun Liu, Rongping Lin, Rongdong Deng

Arsenic contamination significantly affects the quality of copper concentrates, presenting challenges during smelting processes. Considering that covellite and enargite have similar surface properties, they are difficult to separate by flotation, resulting in copper concentrates with excessive levels of arsenic. To address this issue, this study systematically investigated the flotation separation of covellite and enargite in microflotation and bench-scale flotation tests using calcium lignosulfonate as a depressant, with the results indicating that calcium lignosulfonate can be used to separate covellite and enargite because it enables the separation of arsenic-bearing copper minerals into high- and low-arsenic (As 0.57%) copper concentrates. According to contact angle and adsorption tests, scanning electron microscopy–energy dispersive spectroscopy, and X-ray photoelectron spectroscopy, the differential adsorption of calcium lignosulfonate onto covellite and enargite is the primary reason for their distinct flotation behaviors in the presence of calcium lignosulfonate. The selective depressive effect of calcium lignosulfonate provides a novel approach for improving the flotation separation of arsenic-bearing minerals from copper sulfide minerals.

Feb 28, 2024

By T. Hayashi

A sophisticated process of extracting ultrafine sulfide mineral particles of under 1µm size suspended in clay slurry has been developed through studies of electrochemical properties of particle surface. Experimental procedure and data of the process applied to some clay ores containing sphalerite and pyrite, and molybdenite and other sulfide minerals are reported. Discussions concentrated on the function of process reagents, particularly on various modifying reagents, and on the effect of dispersed or flocculated state of ultrafine particles in slurry which affect significantly the performance of the process.

Jan 1, 1982

By E. H. Kurt

INTRODUCTION The simplest way to drill a hole into rock is to strike a steel chisel or drill bit with a hammer. Early miners used this elementary hand technique so successfully in "single jacking" and "double jacking" that the first mechanical rock-drill designers sought to duplicate it. However, in the early developments, the designers were forced to retreat to a construction known as the "piston drill," wherein the entire drilling element is tied to the piston and reciprocates with it. It took nearly 50 years to devise a method of divorcing the two elements and to achieve the original hammer principle used in hand drilling. The Mont Cenis tunnel, drilled through the French Alps in 1861, usually is considered the birthplace of the mechanical rock drill. The Hoosac tunnel in Massa¬chusetts was drilled at about the same time, and the success of these two ventures paved the way for innova¬tions that produced the Burleigh, Ingersoll, Sergeant, and Waugh piston drills between 1870 and the turn of the century. In 1897, George Leyner of Colorado introduced what has been considered the most significant development in rock-drill history. He devised the hollow drill steel for water flushing; when combined with his free-piston hammer drill, this became the first lightweight and dust¬free underground machine. In addition, Leyner's drills introduced improvements such as automatic rifle-bar rotation of the drill steel and chuck, automatic lubrica¬tion, and an enclosed throttle control. During the 1920s and 1930s, automatic feeds, centralizers, sliding cones, and the automatic water back head were developed, laying the groundwork for all pneumatic underground drills currently in use. Since these pioneering efforts, rock-drill development has been concerned primarily with refining the designs and improving the metallurgy to make faster, lighter, and more dependable machines. Fig. 1 illustrates the progress in drilling speed during the first 125 years of rock-drill development; that progress is a credit to the persistence and inventiveness of the designers in the rock-drilling industry. ROCK-DRILL CLASSIFICATIONS To meet the variety of conditions encountered in rock drilling, several distinct types of drills have been de¬veloped. In general, rock drills may be classified as either hand-held or mounted, with the hand-held ma¬chines including the jackhammer or sinker, the jackdrill or jackleg, and the stoper. The mounted drills are com¬monly known as "drifters." Table 1 shows that each type of drill is available in several sizes from different manufacturers. Fig. 2 illustrates a typical rock drill, showing the principal components. The jackhammer or sinker, shown in Fig. 3, is used primarily for general mine utility work such as drilling anchor holes (short vertical holes to bolt or anchor machinery), pin holes (short, usually horizontal holes to fasten sheaves, etc. to side walls), popholes (for blasting large boulders), and similar applications. They also are used for shaft sinking. Jackhammers are classified ac¬cording to weight, and they range from 7 to 30 kg (15 to 65 lb). The rock drill originally known as a jackleg was made by clamping a pneumatic cylinder or leg to a jack¬hammer, both to support the weight of the machine and to feed the tool forward in horizontal or uphole work. The more modern jackdrill refined this concept to make the hinged pivot for the leg integral with the drill cylinder and to group all drill and leg controls in the drill back head for convenience. Fig. 4 illustrates a typical jackdrill. Jackdrills are classified according to cylinder bore size, ranging from 60 to 83 mm (2.375 to 3.25 in.). Because of their light weight and versatility, jack drills are very effective in small drifts, small tunnel head¬ings, and stoping. The larger machines are applied to hardrock formations and in applications where drilling speed is a primary consideration. In soft formations or

Jan 1, 1982

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By F. Ikumapayi

In order to predict and minimize detrimental production problems due to the recycling of process water in sulfide ore processing, the influence of major species, calcium and sulfate in process water on sphalerite flotation was investigated through Hallimond tube flotation, zeta potential, diffuse reflectance Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) measurements using sphalerite mineral sample. Assessment of process water species in flotation was done using deionized water, process water and simulated water containing calcium and sulfate ions in experiments. Hallimond flotation shows increased sphalerite float-ability in process water compared to deionized water, but no significant effect on the presence of calcium and sulfate ions in deionized water using isobutyl xanthate as a collector. The presence of calcium ions reduced the sphalerite?s negative zeta potential, while at higher concentrations, a charge reversal occurred, at about pH 11. FTIR and XPS studies revealed the presence of surface-oxidized sulfoxy and carbonate species on sphalerite at pH 11.5 in deionized water, process water and water containing calcium and sulfate ions. These surface species do not influence xanthate adsorption.

By Truman P. Stauffer

Secondary use of mined-out space in underground limestone quarries is emerging in the Kansas City area where abandoned quarry sites are being renovated into warehouses, factories, and offices. Mining techniques, ceiling heights, and pillar distribution are being altered as planning for the secondary use of mined-out space is combined with the quarrying process. Even the historic urban- quarry land use conflict invites a reappraisal in that this development provides a potential resolution of the problem. Mutual subsidization by dual rock and space interest is changing the economics of rock production. A city is much more than a surficial adjunct superimposed upon the topography of an area. Its development and growth are deeply rooted in the resources, benefits and problems of its underlying geology. The environmental geologist must address himself to more than the quality of a particular resource. He must comprehensively relate resource extraction and processing with the urban emphasis of optimal use which favors long term usage of land over one time economic ventures. Limestone quarrying, closely allied with the growth of many cities, has commonly left a series of scarred landscapes in the path of the burgeoning metropolis. These abandoned quarry sites are barriers to orderly city growth and fail to serve the people as useful and taxable land. Where quarries are functional, supplying the city with needed growth minerals, problems of blasting damage, noise, and dust exist. Technology faces the challenge of making mineral production and processing good neighbors to the urban market they serve. Continued growth of cities may require more efficient use of space below as well as above the surface optimizing land usage so that long term economic benefits may be reflected in improved mining methods.

Jan 1, 1973

By Todd S. Webster, Matthew J. Pierce, Brad D. Krumel

With the Working Shafts and Starter Tunnel under way, it became apparent this 4.7-mile, 19-foot diameter wet weather tunnel was going to live up to its name. The shaft’s pre-excavation grouting was completed, and ground water inflows were slowing project progress. As the tunnel drive was approaching 50% complete a cooperative effort was underway between the owner, engineer, and contractor to raise the base of the Retrieval Shaft by 65 feet to avoid ground water infiltration construction challenges. The tunnel alignment needed to be raised in kind. The project was behind schedule and rethinking the cast-in-place adit work was next on the agenda due to the very wet environment in the tunnel. The race was on to finish the project within the owner’s time constraints while completing multiple redesign aspects of the tunnel alignment and associated adit construction. This paper will evaluate original design criteria and actual in-route design modifications and change management to meet the owner’s just-in-time schedule needs.

Dec 1, 2022

By K. D. Luxbacher, E. C. Jong

Perfluoromethylcyclohexane (PMCH), a member of the perfluorocarbon tracer group of compounds, has been shown to be a viable supplement to the widely used tracer gas sulfur hexafluoride (SF6). This viability stems from the fact that PMCH can be used concurrently with SF6 while maintaining adequate chromatographic separation and comparable sensitivity during analysis. However, the release of PMCH in an underground mine ventilation system is challenging due to its physical characteristics. While SF6 exists as a gas at room temperature and pressure and can be accurately released by a variety of means, PMCH exists as a volatile liquid at room temperature and pressure, preventing it from being deployed in a similar manner. One method to release PMCH is to use a permeation plug passive release vessel (PPRV), which allows for the controlled release of the gas. This paper presents the results of a study evaluating various preparation techniques, plug thicknesses and plug materials of an aluminumvessel PMCH release source, so that a source appropriate for the mine scale may be developed.

Jan 1, 2015

By V. Kecojevic

Environmental and economic costs related to equipment fuel consumption and carbon dioxide (CO2) emission present a substantial challenge to the mining industry. Haul trucks are an integral part of the overall surface mining system and they consume a significant quantity of fuel. Consequently, they produce a significant amount of CO2. The objective of this research is to (i) establish a mathematical relationship among a truck?s fuel consumption, power and engine load factors and (ii) determine the amount of a truck?s CO2 emission and the associated cost that may arise from potential CO2 legislation. In order to achieve these objectives, the authors have considered original equipment manufacturer (OEM) haul trucks, which are commonly used in surface mining operations. The research presented here may be used by mining professionals to help determine the cost and environmental burden of the trucks? application and efficiently manage energy consumption.

Jan 1, 2010

By H. Mischo, F. Daniela, L. Schaarschmidt, I. Paschke

In order to safely store radioactive waste long-term, HAW repositories in saliferous formations have to be backfilled. The main purpose of those backfill operations is the restoration of the geological barrier function of the containment area. For best possible results the used material should be of a comparable composition or characteristic for the host rock formation. Additionally, the material should show a high density after completion of the backfilling process as well as a low permeability. A major aspect to consider in these processes is the minimization of the gap of the backfill body to the roof of the drift. To fulfil those requirements, a micro-structure stabilized crushed salt backfill material has been developed as part of the GESAV-I-project. Due to the material composition of this so-called GESAV-material, salt mineralcrystallization processes start after emplacing it, a process that leads to the polyhalite formation. With the crystallization of polyhalit, the halite grains are bridged, which in return stabilizes the matrix of the backfill. The GESAV-II-project continued successfully what GESAV-I started and determined an ideal backfill method in order to build the backfill bodies composed of GESAV-material. Due to the compaction of the material during emplacement by vibration, high in-situ densities, low permeabilities and a backfill factor close to 1 was able to be reached. In the following SAVER project this journey of practical test underground will be continued.

Mar 2, 2022

By Richard E. Sabaski

The demand placed on the mining industry in the past 15 years for increased production, coupled with lower grade ore and higher cost capital, has resulted in a noticeable increase in grinding mill sizes. The pressure to increase mill size continues. During the mid sixty's and early seventy's, ?larger? conventional ball mills were in the range of 13 - 16-1/2 f t. diameter (4 - 5 m) increasing by the mid 70's to 18 ft. (5.5 m) diameter. At the same time, autogenous mills expanded from 24 - 32 ft. (7.3 - 9.1 m) to the present 34 and 36 ft. (10.b and 11.0 m) diameters. These size pioneers of 16-1/2, 18, and 36 ft. diameter mills from Allis-Chalmers have been free from structural problems, because they were analyzed, modeled, designed, and field tested to meet the challenge.

Jan 1, 1981

By J. M. Mutmansky

A number of previous publications have attempted to provide the practicing ventilation engineer with simple guidelines on the optimal velocity to be used in mine openings. Some of these velocities were meant to be used in metal mining operations and some were meant for coal mining. A careful review of these publications reveals that the optimal velocities were determined based upon assumptions that are not existent today. As a result, they are not suitable for use in a modern coal mine. This paper takes a new look at this problem and determines a statistical relationship for optimal velocity that can be applied under both current and future conditions. The analysis performed here is based upon the determination of the optimal velocity for coal mine entries under variations in power cost, mining cost differential, airway friction factor, time value of money, airway lifespan, and quantity of air carried. A total of 8400 different conditions were analyzed for optimal velocity using computer calculation of the capital and operating cost values. Using the individual values of the optimal velocity derived in the calculations, a linear regression equation was fitted to the data to relate the optimal velocity to the other six variables outlined above. This regression relationship allows the ventilation engineer to make an easy, rapid determination of the optimal velocity.

Jan 1, 1984

By Colin Lawrence

The Port of New York and New Jersey is one of the most heavily used transportation arteries in the world, handling nearly 40 per-cent of the North Atlantic shipping trade and directly providing nearly 230,000 jobs to the local economy. In 2004, $100 billion worth of consumer goods moved through the port. To accommodate future cargo volumes in the port, which are expected to double over the next decade and possibly quadruple in 40 years, deeper shipping channels are needed to provide access for a new generation of cargo mega-ships with drafts exceeding 13.7-m (45-ft) when loaded. Current channels within the harbor range in depths up to 13.7-m (45-ft), thus preventing carriers from using these larger ships, or requiring significant reductions in cargo to achieve lesser drafts to operate safely within the harbor. As part of the Harbor Deepening Project, the Anchor-age Channel would be deepened to 15.2 m (50 ft) below mean low water (MLW), for a length of 5,790 m (19,000 ft). The New York City Department of Environmental Protection (NYCDEP) owns, operates and maintains two existing water siphons in the harbor. Due to their shallow depth, both existing siphons must be relocated before dredging of the Anchorage Channel can be completed. Tom Costanzo, manager of capital programs for the Port Authority of New York and New Jersey (PANYNJ), says that ?While the re-location of the existing siphons under the Anchorage Channel is vital to the success of the deepening program, it is also a story of cooperation among key agencies at different levels of government resulting in improvements that will benefit the people of this region greatly.?

Jun 1, 2010

By Richard S. Klein

Frozen coal creates severe handling problems. Utilities require uninterrupted supplies of coal to meet their increasing coal consumption rates. Difficulties incurred due to frozen coal result in more costly downtime for the utilities. Air cannons, vibratory hammers and thaw sheds are examples of mechanical devices used to break, crack or thaw frozen coal. Recently chemical treatments have been developed as preventive measures. The freezing of coal depends upon a number of factors, of which one of the most significant is surface moisture. The more there is, the larger the frozen coal problem. Slide 1 depicts a graph of frozen coal compressive strength as a function of surface moisture. Below a certain minimum value the coal will not freeze. Above this point, compressive strength is essentially a linear function of moisture over the range practically encountered. By surface moisture is meant the free moisture on coal having a normal vapor pressure as opposed to capillary moisture or inherent moisture. In addition to the straightforward freezing of coal surface moisture binding particulates together, frost formation occurs due to temperature gradients which develop in rail-cars and stockpiles .

Jan 1, 1980