Search Documents

By W. G. Pariseau

Equivalent elastic properties of discontinuously jointed rock masses are computed using a non-representative volume element(NRVE) approach within a three dimensional finite element program. Joint persistence, defined as the percentage of a joint plane that is actually occupied by joint material, is used in the NRVE computations as a step towards greater realism in stability analysis of mine openings. Persistence p is also the probability that a segment of a joint plane is occupied by joint material. Computations reveal a threshold phenomenon in jointed rock mass moduli similar to that observed in percolation theory. A rapid decrease in moduli occurs above a critical value pc(about 0.6). A detailed analysis of the well-known solution for stress about a circular opening in isotropic, elastic ground illustrates the effects of joint set orientation, spacing and persistence. Although stable “on average”, joint segment failures reveal a threat to stability and point towards rational design of reinforcement or support of discontinuously jointed rock masses.

Jan 1, 2003

By Tim O’Neil

Upbeat, surprisingly so, might describe the mood at the2002 SME Annual Meeting and Exhibit in Phoenix, AZ. More than 4,000 mineral professionals gathered for three days of education, networking and product perusal. The Annual Meeting featured the theme, “Minerals for the Future@ SME” at the Feb. 25-27 gathering. Meeting attendance reached 4,039along with 479 exhibit booths show-casing 325 companies. Exhibitors found a good mix of industry types:37% from mining, 19% from processing, 20% from manufacturing and 28% from environment, education and government.

Jan 1, 2002

By A. W. Khair

This paper deals with the design characteristics of cutting tools and the operating parameters these tools are usually subjected to. Eight types of cutting tools/bits with different geometrical shapes and sizes were tested in a linear cutting apparatus, utilizing concrete blocks. The objectives of these experiments were to study the performance of each type of bit, make qualitative assessment of each bit geometry and size and establish cutting parameters for efficient utilization of the tools. During the experiment required forces Fx, Fy, and Fz, cutting, penetrating and lateral forces respectively and audible and sub-audible noises were measured. In these experiments, the depth of cut was kept constant to 1.5 inch while the bit spacing was varied 1.5,2.25 and 3.0 inch (3.75,5.6 and 7.5cm respectively). The results of these experiments indicated that by optimum ratio of depth of cut to bit spacing, the cutting face will be cleaned with the least ridge/land remains between the bit groves, resulting in least specific energy consumption, more large and less fine product particles and substantial reduction of audible noise. The results of these experiments also showed that proper bit design not only decreased cutting energy consumption but also reduced audible noise.

Jan 1, 2001

By V. McLemore, N. Dunbar, K. Donahue

There are three principle lines of evidence that indicate the clay minerals found in the Goathill North (GHN) rock pile at the Molycorp mine are predominantly a product of hydrothermal alteration, not weathering. The unweathered drill core and samples from GHN have similar types and abundances of clay-mineral groups based on XRD analysis. Chemical analyses from the electron microprobe reveal similar chemical compositions for the hydrothermal alteration clays in drill-core samples and clays found in the rock pile. Textural evidence gathered from petrographic and microprobe examination also suggests a hydrothermal origin for clay minerals.

Jan 1, 2007

By M. G. Irish, E. E. Vidal, M. J. Jahraus, P. R. Taylor

An experimental system has been designed to monitor on-line variations of leaching parameters in a closed circuit of cyanide leaching solutions and gold bearing ores. Experiments performed to deter-mine variations in some important leaching parameters of the solution: pH, dissolved oxygen, free cyanide, oxidation/reduction potential, gold content, temperature, pressure and solution chemistry. By comparing results obtained when the leaching solution is allowed to become acid or kept basic, it was possible to infer the chemical reactions that occurred between the solution and the ores.

Jan 1, 2004

By F. F. Peng

The raw-coal feeding system and the upward medium current flow in a dense-medium vessel (DMV) are, in addition to the residence time of particles in the separator, important factors for efficient coarse particle separation. The feed material from a raw coal screen and/or pre-wet screen merge with the major volume of circulating medium as push medium, guided by an adjustable submergence baffle plate deep fed into the separator for effective separation. The remaining volume of the circulating medium enters from the purge and drain hoppers at the bottom of the DMV. This generates a gentle upward medium current flow in the separator, which prevents dense medium stratification/settling and merges as part of the push medium. A two-dimensional, two-phase model developed using computational fluid dynamics (CFD) is used to describe the flow pattern and evaluate the function of the dip plate for understanding the mechanisms of particle separation in the separator. The particle movement in the DMV is also tracked to investigate the major operating parameters affecting the separation performance of the DMV. The simulation results of the DMV separation performance are validated by in-plant test data.

Jan 1, 2007

By M. Rossi

Geologic ore controls are usually interpreted and modeled from cross sections and plans, as they are critical to construct meaningful and accurate ore reserves models. The geologic boundaries are often modeled as two-dimensional surfaces or three-dimensional solids and used as hard boundaries to constrain the grade estimates. In many cases, the geologic model is the most important factor in estimating the mineralized tonnage predicted by the reserves model, since it is generally drawn to separate the volumes of mineralized and waste material within the deposit. Because geologic models are interpreted from widely spaced drill hole data, the accuracy of the contacts of the different zones modeled could be poor. The lack of accuracy in the definition of geo-logic zones can have a significant impact on a resource model. In this paper it is shown that the geologic interpretation can and should be checked for potential biases. In particular, an unbiased overall volume of the original drill hole information with respect to the resulting solids and codes assigned to the block model is sought. In addition, geostatistical conditional simulations can be used to simulate the geologic attributes modeled, thus providing an alternative view of the geology, and a measure of the uncertainty of the geologic boundaries. The simulated geologic model provides an assessment of the impact of alternative geologic interpretations on the over-all uncertainty of the reserves model. In the case study presented here, the uncertainty of the geologic model is quantified for a difficult-to-model, high-grade copper deposit in northern Chile.

Jan 1, 2004

By M. Perolo, A. Contini, E. Ramelli, G. Borgonovo, L. Locatelli

This paper presents the ground settlement monitoring system used during the construction of two tunnels bored by two EPB TBMs, beneath the existing and active railway embankment in Bologna (Italy). The tunnels run close to large buildings and beneath bridges and other infrastructure. Data are collected from remote total stations and from electro levels installed directly on the railway tracks. The automated monitoring system acquires and analyses data then sounds an alarm in the event that there is a problem. Alarms are sent out in case of excessive tilt or settlement. Data is provided through a dedicated web application for multiple-party access, to gather, manage and store monitoring data.

Jan 1, 2007

By Bijan Taheri, Behrouz Maghsodi, Monireh Heshami, Reza Kohan

A common problem recently encountered with the increase in the rate of input feed at Enrichment Plant 2 of the Sarcheshmeh Copper Complex is the loss of value to the tails, translating to lower recoveries. The feasibility of the direct transfer of part of the high-grade concentrate from rougher stages to an appropriate position along the circuit was studied, and two positions were proposed for direct transfer of the concentrate. One position was the feed flow into cleaner cells, and the other was the feed flow into the recleaner cell. The results indicated that transferring the concentrate from the first unit of the rougher stage to the feed flow into the cleaner cells was feasible, with no limitations, while the second position required the installation of a set of hydrocyclones. It was found that the transfer of concentrate to the proposed positions not only addressed the problem of limited cell capacity, resulting in debottlenecking of the circuit, but also improved metallurgical separation efficiency up to 1.4%.

By Douglas B. Silver

Traditional cycle theory would postulate that if you have a supply shortage relative to demand, the price will increase because buyers will incrementally increase the price they are willing to pay to ensure that their needs are fulfilled. As prices rise, more supply will be brought on and will eventually exceed demand. This supply excess will cause the price to decline as producers have to lower their prices to sell their goods. What is interesting is that cycles are simply volatility over time. Without the time factor, volatility simply goes up and down. When we add the time element, a cycle is created. This cycle can be big or small. In mining?s case, we are talking about a Super Cycle ? a big cycle. But a Su-per Cycle can be formed in two ways. It can form by either increasing the wavelength or the volatility. If these two elements are combined, a Super Cycle is formed. It is bigger than the normal cycle in terms of time duration and extent of volatility. A recent study (Fig. 1) conducted by Cuddington and Jarrett showed an interesting proof of Super Cycles and suggests that these cycles last between 15 and 30 years. So, what causes a Su-per Cycle? Is it a convergence of unrelated events or a consequence of related events? In a global community everything is related. Equilibrium theory would also take the position that a Super Cycle is a consequence of events.

Jan 1, 2008

By Zephaniah Varley, Satoshi Akai, Richard Sage, Steve Redmond, Mike Murray, Rohit Shetty, Gerald Skalla

One would be hard pressed to find another project as complex as this one given its configuration, the variety of issues to address and the required construction techniques. Contract C710 is currently under construction as part of Sound Transit’s Link Light Rail, connecting downtown Seattle with Sea-Tac Airport. The paper describes the construction-to-date of the deep mined station under Beacon Hill using the Sequential Excavation Method (SEM). This deep “binocular” station is being mined through some of the most challenging soft ground conditions in the USA. The excavated volume of the station is approximately 60,000 cy (46,000 m3) and the station comprises a variety of geometries and cross sections ranging from 235 sf (22 m2) up to 1,670 sf (155 m2). This underground complex includes platform, concourse, cross-passage and emergency ventilation tunnels together with station egress and ventilation shafts. Various excavation sequences are in use for the different tunnels including the twin-sidewall drifts for the impressive45 ft (13.7 m) wide by 42 ft ( 12.8 m) high concourse cross adits. This station has two train platforms approximately 165 feet (50m) below the surface. This station, constructed in highly variable glacial deposits including water bearing sands and silts approximately 50 ft below multiple perched water tables in an urban setting, creates a very unique and challenging situation. The ground is being managed with various types of ground improvements such as jet grouting and vacuum assisted deep dewatering wells from the surface, and from underground by use of “SEM Tool-box Items” such as barrel vault canopy, grouted pipe and rebar spiling, chemical grout,

Jan 1, 2007

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Kanchan Mondal, Gopi Bylapudi, Anand Bhagwat

Corrosion of steel roof support systems can cause potential premature failure of the support, thus adversely affecting the excavation stability and rock-related safety. An in-house corrosion test system was designed and developed to test full-length roof bolts for material performance based on tensile load capacity and strength under different corrosive conditions found underground. The roof bolts tested are also used to identify the possible corrosion mechanisms that influenced the bolts’ performance over time. Initially, the most commonly used bolt material in the USA, the ASTM A615 grade 60 steel roof bolts, was tested with and without stresses in a simulated underground coal mining environment for approximately 6 months, and the results are discussed. Localized corrosion forms such as crevice and pitting were mainly observed after testing. The stressed and unstressed roof bolts with and without threads that were tested in alkaline coal mine corrosive environment for 6 months passed their load-bearing capacity as per ASTM F432 test standards. From the results, it is concluded that this test protocol could be applicable to test the material performance of different roof bolt metallurgies and coatings with desired modifications to the proposed methodology for the specific underground mine environment. This paper mainly discusses the test system and protocol and shortcomings of the system and makes recommendations based on the observations and results.

By Charles Stone, Madan Naik, Drupad Desai, Karel Rossler

Planning of New York’s new subway line dictated the location of shallow underground station caverns and track crossovers. Clear span openings ranging from70 feet to 100 feet and lengths in excess of 1000 feet, coupled with low rock cover ranging from 25 feet to 40 feet required judicious selection of construction methods, equipment, and proper sequencing of the excavation stages. Rock classifications alone could not predict the behavior of the rock mass during construction. A robust design procedure that considered most of the important aspects of rock behavior and elements of shallow tunnel design, minimized the negative impacts of variable geotechnical data. This paper describes the intricacies of the planning and design of the $16 billion Second Avenue Subway with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2005

A methodology has been developed and demonstrated to be effective in reclaiming surface-mined land for a forestry post-mining land use. The Forestry Reclamation Approach (FRA) has been applied, almost exclusively, to flat or gently rolling surfaces. One of the primary steps in the FRA is to loosely grade the top 1.22-m (4-ft) of soil or substitute root growth medium to avoid excessive compaction. Concern has been expressed by regulators and the public that loose grading on steep slopes could lead to slope failures, which is one of the issues that SMCRA sought to correct. A field investigation was conducted at a steep-slope contour operation in eastern Kentucky to test the applicability of FRA in this setting. Final grading was performed according to FRA standards. The surface consisted of two distinct substitute rooting media. One was unweathered gray sandstone and the other was a combination of gray sandstone, brown sandstone, and topsoil. A variety of native hardwoods was planted following the FRA guidelines. The slope was instrumented with 70 survey monuments to monitor for mass movement. The reclaimed spoil was also characterized using bulk density and penetrometer resistance methods. The characteristics of both spoils are similar to those observed on flat to rolling surfaces where the FRA has been used and, after one year, approximately 70% of the trees had survived. There has been no major mass movement of the slope and slope stability analyses indicate that the application of the FRA has little impact on the overall stability of the slope.

Jan 1, 2011

Colloidal interactions play a critical role in mineral processing, including grinding, physical separation (particularly flotation), dewatering, and tailings management. Despite great energy input in comminution to liberate valuables from gangues, heterocoagulation between valuables and gangues would prevent the separation of valuables from gangues. On the other hand, selective coagulation/flocculation to increase the size of desired fine particles could enhance physical separation and dewatering, while dispersion is needed for fine grinding. To control the state of colloidal dispersions by creating favorable conditions, it is of paramount importance to study colloidal interactions in a relevant system and understand underlying mechanisms. This review summarizes recent advances in developing the-state-of-the-art techniques and novel methods of measuring colloidal forces, including atomic force microscope, surface force apparatus, zeta potential distribution measurement, quartz crystal microbalance with dissipation, and our recently developed integrated dynamic force apparatus. The basic principle of each technique was introduced first, followed by a summary of critical information derived for the relevant mineral processing systems. Finally, the pros and cons of each technique were discussed to emphasize the use of complementary techniques that assist in solving fundamental problems in mineral processing.

By William R. Yernberg

The Cripple Creek & Victor Gold Mining Co.(CC&V) celebrated completion of a two-year, $168.5-million expansion and capital improvement program. An open house celebration was held in the historic mining town of Victor, CO on Oct. 4, 2002. Hundreds of townspeople, the press and other invited guests from the mining industry joined the employees of CC&V in the celebration. The event included mine tours, company displays and a barbecue picnic, complete with a country and western band. The Cresson Mine is located about 40 km (25miles) west of Colorado Springs, CO between the towns of Cripple Creek and Victor. The mine is the only large-scale gold mining operation in Colorado and now employs about 300 (ME, October 2001, pp.21-28). The operation is a joint venture between Anglo-Gold (Colorado) (67%), based in Greenwood Village, CO, and Golden Cycle Gold (33%), based in Colorado Springs. CC&V is managed by AngloGold North America. AngloGold North America is the U.S. subsidiary of AngloGold, the world’s second largest gold mining producer. AngloGold is based in Johannesburg, South Africa.

Jan 1, 2002

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.

By Rameshwar Sah, Bharath Kumar Shanmugam, Govinda Raj Mandela, Marutiram Kaza, Harsha Vardhan, Harish Hanumanthappa

Iron ores obtained from different sources differ in their chemical and physical properties. These variations make the process of grinding a difficult task. The work carried out in this context focuses on three different samples of iron ore, viz., high silica high alumina, low silica high alumina, and low silica low alumina. The grinding process for all the three iron ores is carried out individually in Bond’s ball mill and the total retention time taken by each iron ore sample is calculated. The present investigation focuses on utilizing the calculated retention time of the iron ore as a standard grinding reference time to the laboratory ball mill for optimizing the grinding time of each ore. The desired P80 (150 μm) with an acceptable range of hematite liberation (> 75%) was obtained in the laboratory ball mill after reducing 6 min from the total retention time taken in the Bond ball mill.