Search Documents

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

By Brian Micke, Mick Gavrilovic

The problem of rock hang-ups in underground mining operations has been a continuing one since the days of the “hang-up man”. This position commanded the highest pay of any underground worker in many historical Western U.S. underground bulk-mining operations, due to the occupational hazards of the job. Although underground mining techniques and especially work practices have changed greatly since then, the hang-up problem is a continuing one in many mines which use gravity flow of coarse rock in their transport systems or in those mines where stressed ground causes rock slabs to spa11 and bridge rock passes and stopes. In addition, with mechanized underground open-stoping mining methods now being used in many different types of ore deposits worldwide, this problem has again emerged as a very significant one in many of these highly mechanized operations. This is especially so where the remote operation of loaders is used for removing blasted rock from underground open stopes.

Jan 1, 1999

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By Gregory B. Poole

As part of a $3.5 billion program to improve the antiquated waste water system in the city of Atlanta, the Nancy Creek Tunnel is being constructed across the northwest portion of the city. This tunnel is over eight miles long and is being constructed using Tunnel Boring Machines (TBM) for the majority of the tunnel and conventional drilling and blasting for three shafts, starter and tail tunnels and four connecting tunnels, totaling 2400 feet in length. An extensive public relations program was developed for this project. A group effort by the owner, engineer and contractor produced a public relations program that both informed and educated the public of the anticipated perceptions and effects of the blasting and TBM activities.

Jan 1, 2005

By William H. Highlands

Lightning is a natural phenomenon which poses a potential hazard to people, structures, and equipment unless adequate protection is provided. The type of protection required is related to the nature and of the facility. The decision making process involves a number of interrelated factors which should be considered when determining the need for protection.

Jan 1, 1989

By John Watson

New Technologies, New Challenges and New Opportunities For quite some time now, numerous explosive manufacturers have spent untold man-hours and millions of dollars trying to develop a blast initiation technology that would “once and for all” provide users with what was once believed to be only a theoretical possibility...nominal timing. Zero “cap scatter” (the amount of variation of delay timing from the targeted nominal) has been the industry’s goal ever since delays were first introduced into the marketplace. Just as adding delay time between blast-holes improved blast performance since their introduction, having the wrong delay or a poorly timed blast has proven to be very inefficient and in many cases hazardous. The question of how precise a blast initiation system needs to be still remains unanswered, but electronic detonator systems being used today indicate that significant improvements can be achieved over conventional pyrotechnic detonators. These systems can typically provide single digit millisecond ranges of variability, if not sub-millisecond in some cases.

Jan 1, 2003

By Ken Cross

This paper aims to demonstrate that explosives organizations and workers have a legal, moral and financial duty to be able to demonstrate their competence when required, and how that may be achieved at any level from explosives storekeeper to senior explosives engineer on a major project. The concept of competence is outlined, as are the benefits to members of staff, management and the organization, particularly in a regulatory regime that includes competence management as a key performance indicator.

Jan 1, 2013

By C B. McCampbell, R W. Jr Bickes

Sandia National Laboratories has developed a semiconductor bridge (SCB) igniter for the ignition of a variety of explosive materials. When subjected to a low-energy current pulse, the bridge bursts into a plasma causing rapid ignition of the explosive material pressed against the bridge. Despite the low energies required for ignition, SCB components have proven to be explosively safe, meeting both no-fire and electrostatic discharge (ESD) safety requirements.

Jan 1, 1991

By Daniel Mallette, Richard Goodridge, C M. Lownds

Despite a world of mobile devices that has many of us taking the ability to communicate wirelessly for granted, an in-hole wireless initiation system was thought to be not viable. The known and common wireless communication techniques are not suited to this application. To overcome this, we have developed cutting edge technology to communicate to our initiating devices more than 1km through solid rock.

Jan 1, 2016

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Jerry Chambers, Scott Crabtree, Randy Wheeler

Destructive wave interference has been studied in theory for many years. In application however, limited information can be found. Recently, circumstances have enabled a multidisciplinary team to utilize electronic detonators and seismograph analysis to create destructive wave interference in an underground production blasting application. Springfield Underground, located in Springfield, MO, in conjunction with Orica, ETI, White Industrial Seismology, and the University of Missouri – Rolla has shown the ability to use destructive wave interference in underground blasting to reduce ground vibrations directly above.

Jan 1, 2006

By Rob Farnfield, Charlie Adhock

The measurement of near-field shock has always been an attractive proposition for those working in the field of explosive and blast performance. The most commonly employed technique involves the use of piezoelectric accelerometers. Although highly effective, these complicated devices are relatively expensive and are often destroyed in the blast event. This paper describes the development and field-testing of a shock sensor of sufficiently low cost to enable it to be routinely used in product blasting. This new device is based on piezoelectric wafer technology and does not require any external signal conditioning. The device is housed in a small cylindrical package with approximate dimensions of 30mm (1.2”) length and 5mm (0.2”) diameter. It has been determined that the most effective way of fixing the device to rock is in a small diameter hole with epoxy glue. Alternatively the sensor can be simply placed in holes filled with either water or bulk emulsion explosive.

Jan 1, 2005

By Alastair Grogan

In October of 2002, the author was retained by Public Works and Government Services Canada, on behalf of the Department of National Defense, to design, construct and test the effectiveness of a bubble curtain system at an underwater demolition range, near Victoria, BC. The purpose of the bubble curtain was to reduce the potential for fish mortalities at the site. This paper presents some of the elements of the design, along with the results of overpressure monitoring during blasting and compares the results of fish mortality and animal behaviors with and without the bubble curtain in operation.

Jan 1, 2005

By G. Adderley, A. Wetherelt

The problems of poor drilling in underground operations have been highlighted on many occasions. Incorrect collaring and poor angular deviation can all lead to an increased block size, dilution, over-break adding to both cost and time, while in a tunnelling operation sidewall damage and a poor percentage pull from a blasted round has similar consequences. This paper sets out to further investigate the ability of the laser scanner method of obtaining drill hole deviations and collaring errors at the face as described by Wetherelt and Williams (2006). Tests were carried out to compare measured inter-hole burdens from this method in comparison to that obtained using a total station survey. To investigate the ability of these methods to accurately determine drilling errors, a field test was carried out through an analysis of a series of pre-drilled blast holes of known inclination and direction. A time-motion study was also conducted for a varied number of holes to assess the usability of each method. In line with current research into blast vibration being undertaken at the Camborne School of Mines, 6 cut blasts were carried out to establish the effect of poor drilling on a blasts success to see whether an increased burden at the toe of a hole had an influence on vibration.

Jan 1, 2009

By Ricardo Gaviria, Vincinte Acosta

There are major blast design and field procedures differences between conventional blasting in horizontally bedded coal seams and blasting underneath coal seams in a multi seam deposit with seam inclinations of 14 degrees or more.

Jan 1, 1995

By Ron Lutz

In today’s world, production is the name of the game. We are all in business to make money. In the Quarrying and Mining industry the same holds true. The primary goal is to develop the best drilling and blasting program available to maintain uniform fragmentation to maximize production. Also we want to maintain drilling and blasting costs and minimize escalators. This paper is intended to discuss ways for all parties (quarry’s, blast service and drill companies) to attain this through understanding what can be done to help blasthole drilling and production. Blast designs and seminar’s emphasize the accuracy of drilling to produce better fragmentation. Blast design must also include basic concepts in the drilling process. The type of drill to be used for example whether it is a crawler or truck mount, top hammer or down the hole is important. Quarry operators have a role to play as well. They hold the key to the production of drilling. What the customer does or does not do has a direct effect financially to the drilling. The phrase of pay me now or pay me latter comes to mind. This paper will explore the detail of planning that is required by the quarry and/or blast service companies before a single hole is drilled. The drill must be able to meet the production need of the operation. The type of drill available and what can and cannot be done. The drill cost must be competitive. This paper will touch on comparison drill costs from 1967 to 1999.

Jan 1, 2000

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By John Dean Smith

"In many operations the two most overlooked aspects in the drilling and blasting process is theblast optimization and explosive selection. Often times we find a blast design that seems to work andproduce acceptable results and will use this cut afier cut, even years. When in reality one should never become complacent and should be constantly looking for ways to improve the drilling and blasting operation."

Jan 1, 1995

By Vic Sterner

As cities and towns continue to grow, the need to install sewer, water, gas and other utilities becomes a necessity and the blasting of trenches for these service lines probably constitutes one of the most important forms of blasting in built-up areas. There f o re, understanding how explosives can be safely used in the most efficient manner is of prime importance. The need for protection against flyrock must be emphasized. The first consideration is that all explosive c h a rges should be located well down in the blastholes. The golden rule is to ensure that the depth of top stemming is never less than the burden on the hole. In the case of shallow holes, the minimum depth of stemming should not be less than 18 times the charge diameter, if airblast and flyrock are to be controlled. If there is a doubt, then additional cover and/or blasting mats should be used. Putting too much burden on blastholes is another possible cause of flyrock and raising ground vibration levels. Overburdening of explosive charges will also result in the blastholes not breaking to grade. This in t u rn re q u i res additional drilling of shallow holes down in the trench to achieve grade, thus further increasing the h a z a rd of flyrock .

Jan 1, 2004

By Ron Glowe

This paper shows the potential of a new computer model, using the Glowe-Tech (GT) Tonnage Analyzer program to compare drilling and blasting results. This model uses the crushers and conveyors as measuring tools in aggregate quarries in the USA and Canada. All data is collected using commercially available kilowatt transducers and an analog input/output automation module. There are two areas of measurement used to compare results. The first area is the tonnage moved by key conveyors to show the split in products produced and the actual rate of production. If belt scale readings are not available then the Glowe-Tech Tonnage Analyzer can be used to convert kilowatts from the conveyor motor to tonnage. The second is the tons of rock crushed per kilowatt hour of energy consumption by the primary and secondary (optional) crushers. This modeling process works best if blasts are mucked and crushed in sequence. There are many other variables such as crusher types, crusher settings, screen sizing and actual geology in the pit that can influence the results, however if variables can be standardized then definite trends can be seen when comparing drilling and blasting results

Jan 1, 2005

By Robert Lee, Jeff Corace, Rob Cyr

Blasting in the heart of the historic Byward Market District of Canada’s capital, Ottawa, presents a unique set of challenges. The obvious difficulties arising on projects requiring blasting within 3 m (10 ft) of 125 year old buildings in various states of disrepair have been encountered and successfully dealt with countless times before. The complexities increase exponentially when tenuous property boundaries, unknown structural details, litigious histories and the need for encroachment agreements lead to individuals with competing interests all able to impact the same operation. Blasting on three projects in the Market was started in early 2005 after months of negotiation. Ultimately, the potential for the projects to proceed hinged on the ability to successfully disseminate blast data to the various stakeholders. As part of the agreements drawn up, property owners demanded immediate notification of the measured vibration levels with contract provisions including clauses such that any exceedance of the USBM criteria immediately triggered project shut down and complete blasting program redesign, and approval by all parties. With stakeholders located in various cities and, in some instances, on various continents, a conventional attended monitoring strategy would not satisfy the requirements. In response to the critical reporting need, Explotech Engineering Ltd. installed unattended monitoring stations around the sites, all incorporating wireless telemetry. After each blast, data was automatically transferred from the monitoring stations to a web-linked server via the wireless network, where it was immediately available to project stakeholders through a password protected website. The solution required a unique blend of data acquisition, telemetry, database, and security technologies, all married to produce a reliable system that was easy to maintain and use. While these types of systems were originally developed for use as permanent monitoring networks in operating mines and quarries, monitoring professionals are increasingly benefiting from the technology on temporary building projects that have typically been the realm of attended monitoring strategies. Globally, this has emerged as a solution to provide more timely access to data for stakeholders, and to minimize the legal exposure from multiple violations of vibration limits. As this trend is likely to continue, the regulated vibration control industry is likely to see a continued shift in technology development to leverage wireless networks and the Internet to continue to improve data transfer, archiving and distribution.

Jan 1, 2006