Search Documents

By C. F. Starr

This paper deals with the various types of cable in use in mines, with special attention paid to their construction. There will be a few comments regarding the different insulants, jacketing materials and armouring used, depending on their application. Governing standards and the differences therein will also be discussed.

Jan 1, 1969

By R. E. Hamilton

"The requirements for effective optimization of a mineral dressing operation are discussed, with specific reference to a flotation system . Also considered are the relation-ships between automatic control and optimization pro-grams. Variables are classified into the following groups, and the significance of the classification is discussed: (a) Directly measurable (b) Directly manipulable (c) Uncontrollable (d) Calculable from measurable variables (e) Affected by changes in manipulable or uncontrol-lable variables. New sensors for measuring variables not normally measured are described."

Jan 1, 1967

By L. Fernandes

A factorial study was performed to investigate the relative effects of temperature, copper concentration and meso-2,3-dimercaptosuccinic acid (DMSA) concentration on the performance of thiosulfate leaching of gold. A total of 24 leaching experiments were performed representing eight unique combinations of high-low levels of the three factors performed in triplicate. All investigations were performed in an electrochemical cell with an electrolyte composed of 0.1 M sodium thiosulfate with a combination of copper (either 0 mM or 1 mM) and DMSA (either 0???or 1µM). All leaching investigations were conducted under open circuit while the electrolyte, which was open to the atmosphere and mechanically stirred, was maintained at either 25°C or 50°C. After 1.5h of leaching the amount of gold in solution was quantified using ICP-MS analysis from an aliquot of the electrolyte. Results indicate that DMSA addition improved gold leaching performance, most notably at 50°C and with addition of copper. Under this unique condition, the quantity of gold in solution was reproducibly and significantly above the average response of all other factors studied.

Jan 1, 2014

By Shinji Shirakawa

The gold wire bonding technology is widely used for electrically connecting aluminum pads on IC devices to external terminal of semiconductor. In 1960?s, the tensile strength of gold bonding wire was about 100 MPa only. However, recently the wire with 300 MPa in strength has been developed. Since the gold bonding wire was started to use for IC package in early 1960?, the many types of gold bonding wire has been developing continuously in order to meet market?s needs, such as high density, small size and thin type of IC packages. Moreover, electronic equipments were used in automobile applications and also demanded good reliability under severe temperature environment. Thus Au-Pd alloy wire has been introduced instead of the wire with 4N(99.99wt%) purity gold to provide excellent reliability in Au-Al bond interface. The phenomena at Au-Al interface in the high temperature storage have been already explained by several studies as follows. There are five phases of inter metallic compound (IMC) between gold and aluminum. Just after bond gold ball on aluminum pad, Au5Al2 phase was formed and occupied almost all of IMC area. During high temperature storage test, Au5Al2 phase transformed to Au4Al phase, then this phase was corroded by Bromide (Br) ion that was isolated from molding resin. Thus the reliability between Au and Al degraded. In case of Au-Pd alloy wire, the concentrated palladium phase (Au-Pd-Al) was formed at the interface between Au alloy ball and Al pad. The Au-Pd-Al phase prevented from transforming between Au and Al, therefore Au5Al2 phase was hard to transform to Au4Al phase. Consequently the reliability at the interface between Au alloy ball and Al pad was less degradation. However, in recent study using several advanced analysis technique, Au4Al phase was found at the interface between Au alloy ball and Al pad same as the case of conventional gold wire (4N purity gold bonding wire). It was suggested that the formation of concentrated palladium phase (Au-Pd-Al) related the excellent reliability at ball bonding process.

Oct 1, 2003

By Jeffrey S. Loen

"The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 x thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995

By R. Shamsodini, A. Poor Zaeif Doost, H. Haji Amin Shirazi, M. R. Garmsiri

"With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.INTRODUCTIONThe flotation circuit at Miduk Copper Complex consists of five flotation columns as roughers and ten mechanical cells as rougher-scavengers. According to design criteria, 75% of the final product was expected to be produced by the rougher columns, while most of the feed consisting of liberated valuable particles is introduced into rougher-scavengers. To liberate locked particles, the rougher-scavengers concentrate is introduced into the regrinding circuit (see Figure 1 below). The regrind mill is in reversed closed circuit with a secondary hydrocyclones cluster, and the cyclone overflow is introduced into three parallel cleaner columns. Cleaners concentrate reports to concentrate thickener and the column tailings is introduced into six mechanical cleaner-scavenger cells. The cleaner-scavengers concentrate reports to the regrind circuit(Figure 1)."

Jan 1, 2012

By Th. Hassel

The application of magnesium as an absorbable biomaterial demanded the consideration of the alloy composition, the mechanical properties and the corrosion a special adapted material development in terms of the human biological system. Magnesium for technical applications mostly comprised alloying elements up to 10 wt%. Thereby often metals (e.g. rare earth and aluminum) with high toxic potentials are used to optimize the mechanical properties. To minimize toxic reactions during the degradation of a absorbable magnesium alloy, the Mg-Ca system is being selected and investigated because both elements belong to the mineral nutrients. Rods and small tubes are produced by extrusion of gravity die casting billets (Ca-content 0.4 to 4.0wt%). The positive grain fining influence of calcium and its improvement of the corrosion behavior are additional advantages. The microstructure, the mechanical properties and the corrosion attitude are investigated. The results show that an optimal composition of micro alloyed Mg-Ca and ideally processing parameters lead to 16% strain and a tensile strength up to 185MPa. Electrochemical investigations and measurements of the hydrogen production demonstrate the influence of the Ca-content to the corrosion behavior of the investigated alloys.

Jan 1, 2006

By J. E. Rehder

IN A DISCUSSION of use of any material of ?construction in the mining industry, two points of view must 'be kept in mind - that of the producer or manufacturer of mining and metallurgical equipment, and that of the maintenance and operating staff of the mining plant. In the first case, the choice of material of construction is up to the manufacturer and the user of the equipment has little direct say in the matter. However, if materials are badly chosen and the equipment does not function properly, wears out rapidly, or costs too much, repeat orders ?will likely go to a different manufacturer, so that, in the end, the consumer or mine operator does have the final voice. In the case of materials for maintenance work and plant operations, however, .the mill personnel have direct control over purchases and it is then that a well-balanced knowledge of materials, their properties, and their costs, can be directly useful. With all materials of construction, the final criterion is unit cost versus service performance, so that the lowest possible total operational cost will be obtained. Sometimes this means using the cheapest material available, sometimes the most expensive, but in any case careful analysis of service performance, replacement cost, and material cost is essential to determining the material that produces lowest total cost.

Jan 1, 1956

By E. G. Leonardon

The question of geophysical prospecting is one that is beginning to occupy a pre-eminent place in the minds of those actively concerned in the discovery and exploitation of ore deposits. This is in marked contrast to the reception accorded such ideas when the Junior author, six and a half years ago, began introducing electrical prospectii1g to the mining fraternity on this continent. Happily, the mention of geophysics no longer evokes the sceptical and pitying smiles that it did in those days. A little reflection will show that modern geophysical methods are merely a logical development from pre-existing technique. In the study of geological problems, is it not logical to use all possible physical properties of matter? The study of crystal form and cleavage, the examination of thin sections of minerals by means of polarized light or ordinary light, in fact, utilize physical properties of minerals for the benefit of the geologist. These are, of course, laboratory methods, and the extension of the study of similar properties into field work was inevitable. This began with the magnetometric surveys, used as early as 1760 in New Jersey to locate iron ores. Eighty-four years later, John Locke's work in the United States resulted in pointing out relationships between the terrestrial magnetic field and main tectonic features of the earth's crust.

Jan 1, 1928

By Guoxiang Chi

Hydrocarbon fluid inclusions entrapped in diagenetic minerals may be used to constrain hydrocarbon exploration models in two aspects. First, the distribution of different types of hydrocarbon inclusions in different tectonostratigraphic domains, and their relationships with organic matter maturation levels may reflect a regionalscale variation in the thermal regimes of the hydrocarbon systems. Second, the relative timing of hydrocarbon inclusions in the diagenetic history may provide constraints on the evaluation of reservoir potential. This paper summarizes the distribution of hydrocarbon inclusions in four different Paleozoic tectonostratigraphic domains in eastern Canada, discusses its implications on hydrocarbon systems in the different domains, and finally provides two examples to show how the relative timing of hydrocarbon inclusions may be used in the evaluation of reservoir potential. Oil inclusions mainly occur in host rocks that are within the oil zone, although some are found in units in the condensate zone. Light hydrocarbon inclusions occur in the dry gas zone, and methane inclusions were found from dry gas zone to anchimetamorphism zone. This correlation between hydrocarbon inclusions and host rock maturation implies that the hydrocarbons were derived from source rocks having a maturation level broadly similar to the host rocks. Although the Paleozoic rocks are generally relatively poor in reservoir quality, the two examples provided in this paper show that in some stratigraphic units, significant secondary porosities could have existed prior to some hydrocarbon migration events, thus favoring the accumulation of hydrocarbons.

May 1, 2001

By John A. C. Fortescue

There is a need for better communication between scientists who plan and carry out mineral exploration research in glacial terrain and the exploration geologists who look for mines. In this paper, four ways in which workshops could be used to close this communication gap are described and discussed in relation to the solution of this problem in Canada.

Jan 1, 1973

By C. Han, S. J. Zhou, Y. B. Shen, D. Z. Wei, P. Fang

"Collecting property of two hydroxamic acid collectors have different type of nonpolar structure to hemimorphite has been comparatively studied via monomineral flotation test, and the reason causes different collecting performance has been discussed from the view of relationship between molecular structure and collecting property. The flotation tests results show that C5-9 hydroxamic acid has an unbranched linear alkyl nonpolar group shows better collecting property to hemimorphite than cyclohexyl hydroxamic acid which has a naphthenic nonpolar group. FTIR detecting results show that the adsorption type of collector adsorbed on hemimorphite surface is chemical adsorption. Calculation results of polar group’s geometric structure parameters, polar group’s electron density distribution, octanol-water partition coefficient (logP) and molecular frontier orbital energy show that the key factor caused different collecting property of two collectors to hemimorphite is the logP; unbranched linear alkyl nonpolar group is more conducive than naphthenic nonpolar group to make hemimorphite particle more hydrophobic.INTRODUCTIONZinc-bearing mineral recovered from lead-zinc ores is the main source that people can obtain zinc resource from nature. However, natural sulfide ores are currently getting depleted steadily for the primary zinc source. In order to satisfy the future demand of zinc resource, there is an obvious recognition that the recovery of zinc oxidized minerals from the ores is a crucial alternative (Hosseini & Forssberg, 2007; Navidi Kashani & Rashchi, 2008).But the fact that can’t be ignored is the flotation of zinc oxidized minerals is much more difficult than that of zinc sulfide minerals, which is mainly due to the flotation characteristics of these zinc oxidized minerals such as lower selectivity and higher reagent consumption, as well as complex and variety of lead-zinc ores. Presently, there have been many various beneficiation technologies used for recovering zinc oxidized minerals and dealing with ores for recovering metallic zinc such as flotation and hydrometallurgy (Abkhoshk, Jorjani, Al-Harahsheh, Rashchi, & Naazeri, 2014; Önal et al., 2005). But from an overall perspective, flotation is the most common method used for the beneficiation of zinc oxidized minerals, and there have been extensive investigations conducted on the flotation of zinc oxide ores (Ejtemaei, Gharabaghi, & Irannajad, 2014). Until now, the most well-known method used commercially for the flotation of zinc oxidized minerals is sulfidization with sodium sulfide and flotation with a cationic collector of amines containing from 8 to 18 carbon atoms. However, a major problem for this method is the large amount of fines and slime results in the increase of reagent consumption and promotes the phenomenon of slime-coating. For preclude this negative effect, the de-sliming and processing optimization is indispensible (Peres, Borges, & Galery, 1994; Salum, de Araujo, & Peres, 1992)."

Jan 1, 2016

By R. Kong, X. W. Zhang

"High pressure (up to 50 MPa) isotropic compression tests were performed on marble, gneiss and sandstone specimens, of which represents the typical rocks, to investigate isotropic compression deformation characterization at room temperature. Experimental data with respect to volume change in loading and unloading are presented. An apparent volume change inflection point (sensitive stress) was observed at a lower pressure range for porous sandstone, indicating that the elastic-plastic behaviour arising in the isotropic compression stage, but for tight crystalline rock, the sensitive stress is much higher, not probed prior to 50 MPa. The irrecoverable volumetric strain in the unloading can be seen for sandstone as well. The anisotropic deformation was discussed in terms of the axial and radial strain measurement. It was found that essential features of mechanical anisotropy are the irreversible in deformation range. The deformation feature in the isotropic compression tests is a very complex issue due to the factors concerning the stress history, unloading in sampling and in-situ stress. INTRODUCTIONThe isotropic or hydrostatic compression condition that stress is compressive and has the same magnitude for all direction, which is expressed as s1=s2=s3 in principal stress space. A yield locus of soils subjected to the isotropic and anisotropic compression was widely known, for instance Cam Clay model, which forms a closure cap model. However, the similar isotropic compression yield curves for rocks, especially for hard rock, was not established due to the geo-stress in the rock mass is much less than the socalled isotropic yield stress. And hence, the previous experimental studies on the hard rock have been made tend to on the stress-strain-strength relationship (Handin & Hager, 1957; Edmond & Paterson, 1972; Menéndez et al., 1996). Perhaps the yield curves related to an increasing in the hydrostatic pressure is not forced to construct for hard rocks, undoubtedly, the deformation data in this processing is valuable to assess the bulk module (Fabre & Gustkiewicz, 1997), anisotropy (Niandou et al., 1997), field stress (Hakala et al., 2007). Furthermore, many rocks store much elastic volume strain energy link to the hydrostatic pressure exerted, following a deviator stress applying, to drive the unstable brittle fracture for hard rock. Latter was studied to interpret the incentive of rock burst. However, volume change characteristic in the isotropic compression behaviour have been scarcely studied experimentally to our knowledge, less application related to the fracture in hard rock as well. The mechanical behaviour in the isotropic compression of hard rock is notably affected by the original structure anisotropy, stress history and stress condition before sampling, all of which need reasonably assess. It is also a useful understanding to study isotropic compression that elastic and plastic volume change in the isotropic loading and unloading, and the micro crack evolution throughout it."

Jan 1, 2015

By A. F. Abd El-Rehim

The behavior of both transient and steady state creep of Al-4.5 wt% Cu and Al-4.5 wt% Cu-0.1 wt% In alloys was investigated using a constant stress where torsional oscillations of different frequencies and shear strain amplitudes were operated at various working temperatures. An augment in both transient and steady state creep rates was observed by increasing both frequency and shear strain amplitude of the applied oscillations. The mean values of the activation energy of both alloys for both creep stages were found to be equal to that quoted for dislocation intersection mechanism.

Jan 1, 2006

Mirador - Overview ? Located in Andean foothills of SE Ecuador ? Copper-gold porphyry hosted by calc-alkaline Late Jurassic granitic and porphyritic rocks ? 438 MT of 0.61% Cu and 0.19 g/t Au measured and indicated resources (at 0.4% Cu cut-off) ? Additional inferred resources of 235 MT of 0.52% Cu and 0.17 g/t Au ? Initial 25,000 tonnes/day production, expanding to 50,000 in year 6 320 MT of 0.62% Cu, 0.2 g/t Au ore mined at an average 1.4:1 strip ratio over a 21 year mine-life

May 1, 2006

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By J. E. Rowland

NIOCALITE is a new mineral species which has been identified in rock from the Oka district, Quebec. It occurs as prismatic crystals up to l 0 mm. in length and I mm. in width, in coarse, white, crystalline calcite with associated apatite, diopside, biotite, pyrochlore, and niobian perovskite. The crystals of niocalite are light yellow in col-our and have a vitreous lustre. The optical properties of niocalite (I) are as follows: Biaxial negative -2V = 56° a = 1.700, [ ] = 1.730 Birefringence y -a = 0.030 Optic orientation: X = b, Z/\c 12°, Y , /\a = 32° The specific gravity is 3.32 and the hardness is approximately 6 (Mohs scale). A detailed analysis performed on 2.4 gm. of hand-picked material reveals that niocalite is essentially a calcium niobium silicate. Table I gives the result of the analysis. Crystals of niocalite, apparently suitable for X-ray diffraction work, were selected, and single crystal photographs were obtained using both Weissenberg and Precession cameras. Initial difficulties were encountered in interpreting these films, and in correlating the crystal data with the optical data. The in-consistencies were explained by the fact that every grain examined was twinned to some extent.

Jan 1, 1957

By J. P. Wiser

THIS paper discusses testing and quality control of milled asbestos fibre. It has been composed with the intention of: (I) Summarizing past, present and probable future methods of testing and classifying the various grades of commercial asbestos produced by the Quebec asbestos industry. (2) Acquainting those unfamiliar with the methods used for evaluating, testing and controlling the grading and the quality of Quebec chrysotile asbestos fibres with some of the physical and chemical procedures currently used for that purpose. (3) Discussing some of the complications facing the producers, such as variations in the orebody and special requirements of asbestos manufacturers. ( 4) Detailing some of the present quality control methods. SUMMARY OF PAST, PRESENT AND PROBABLE FUTURE TESTING METHODS Past During the first years of production of commercial asbestos in the Province of Quebec, fibre testing and quality control were based principally on dry screen analysis and visual inspection. These methods were gradually expanded during the period from 18, 90 to 1932. In 1932, standardization

Jan 1, 1962

By W. G. Deeks

CANADIANS are world leaders in marketing metal and mineral products. Noranda Sales Corporation Ltd. is an international metal and mineral product marketing company operating from Toronto and London, England, where it operates a wholly owned sales subsidiary and is a 50% partner in Rudolf Wolff and Company Ltd., a charter member and the largest metal broker on the London Metal Exchange. Noranda Sales employs 97 people, of whom 52 are university trained and professionally competent in international resource product marketing. We market for 19 companies or divisions in the Noranda Group and 39 companies for whom we act as agent, consultant and purchaser of resource production. Our business in 1976 was 1.5 billion dollars carried out in 45 countries and covering 24 products and materials. Today, ownership of most of the mining industry in Canada has transferred back to Canadians, and this is said with the knowledge that a significant part of the Canadian industry has been Canadian owned and managed from its very early days. Noranda Mines Limited is such an example. It was born in 1922 as the result of a copper-gold showing at Noranda, Quebec, discovered by Ed Horne, a prospector, financed with a grubstake by a syndicate mainly composed of New York businessmen. Shortly after the discovery, when the shares of the company had risen, the syndicate was sold to Canadian interests and, since that time, Noranda has been dominantly Canadian owned and certainly Canadian managed. Today, over 90% of Noranda's shareholders are Canadian, who hold an equivalent percentage of the stock.

Jan 1, 1977

By Burns Sutherland

Although some mine hoisting systems incorporating steel wire ropes on drum hoists experience completely dependable performance on the hoist ropes for many years, other rope records illustrate an erratic behaviour pattern and, as such, become a source of concern to the operator. This paper describes the causes of the difficulties most commonly encountered and incorporates methods of providing preventative or corrective maintenance. When such a program is utilized wisely, within the allowable limits of shaft time available, it can be the means of avoiding many unforeseen circum-stances and of reducing operating costs, as well as rope costs, to a mini-mum.

Jan 1, 1970