Search Documents

By C. Fortin

ABSTRACT The subject of gold flotation has been reviewed extensively. Most of these reviews focus on the theories of gold flotation and the physical and chemical effects that may impact the efficacy of the gold flotation process. The current status of gold flotation chemistry as it is being applied in industry has not been widely addressed. This paper reviews current gold flotation practice and research advancements and discusses how these applications tie in with the current understanding of gold flotation chemistry. Survey results from worldwide gold flotation operations are analyzed. Potential future areas of gold flotation research are highlighted.

Jan 1, 2013

By S. Shairp

"After cooling and thickening, slurry from the second stage of the Hudbay zinc pressure leach circuit is filtered and washed on a belt filter prior to disposal. At times, the belt filter can be a bottleneck to the process. Preliminary studies show that filterability of the second-stage (HAL) autoclave leach residue can be indicated by particle size distribution of the filter feed and filtered residue cake. In particular, the Volume Weighted Mean Diameter, D[4,3], generated by a laser diffraction particle size analyzer from samples of HAL Filter feed, shows residues that filter more poorly have a lower Volume Weighted Mean Diameter than those that filter better. INTRODUCTIONHudbay produces cast zinc metal from blends of zinc concentrates at its metallurgical complex in Flin Flon, Manitoba, Canada, using Sherritt’s two-stage pressure leach process (Collins et al., 1994; Collins et al., 1995; Barth et al., 1998; Shairp et al., 2006). Pressure leaching replaced the original roastleach- electrowinning process in 1993.Filtration for the second-stage (HAL) leach residue originally consisted of two stages of vacuum drum filtration with intermediate cake repulping stirred tanks. As part of Hudbay’s 777 Project, with a designed increase in cast zinc production, a pre-feasibility study by SNC-Lavalin Inc. showed that losses of soluble zinc in the zinc pressure leach residue could be reduced by installing more efficient filtering and washing equipment. Based on laboratory performance, capital cost, installation ability, and potential operating cost savings, a 70 m2 Filtres Phillipe belt filter was chosen for the HAL residue, and commissioned in 2000/2001.When the HAL belt filter is performing well, there is no pooling of water on the surface, moisture content is relatively low, and subsequent analysis shows that water soluble zinc content is relatively low. There have been occasions where the filter has performed poorly with respect to the aforementioned parameters. Aside from the filter experiencing mechanical difficulties, there are several variables affecting leach residue filtration:"

Jan 1, 2012

By I. Farr, H. Wittens

"In 1989 and 1990 abnormally high levels of arsenic in ore from the Thompson Open Pit Mine threatened Manitoba Division's electro-nickel production. The paper will discuss our development of a flotation process to separate pentlandite and gersdorffite (the prime nickel and arsenic bearing minerals).The presentation will focus on the development of the process from conception, through lab and plant test work, to plant optimization and full scale production. The paper will conclude with the benefits and cost of the completed project.INTRODUCTIONRejection of arsenic from nickel sulphide ores was not a primary concern in the Manitoba Division until 1989. At that time increased production in the Thompson Open Pit mine, which contains high arsenic ore zones, resulted in excess amounts of arsenic in the Thompson Refinery affecting electro-nickel quality. This problem was resolved through extensive efforts by Mill personnel. The purpose of this paper is to familiarize the reader with- the Thompson Mill.- the mineralogy of the Thompson orebody.- the evolution of Ni/As separation in the Mill.- the metallurgical impacts of the separation on the Mill.- the importance of the separation to the Manitoba Division."

Jan 1, 1991

By D. Vanin

"Conventional single heading track drifting in the hard rock mining industry has not shown any significant improvements in advance rates, despite the advent of modern track jumbos and igh speed muck handling systems .This paper presents Kiena 's experience in using a 7 ft 2 in. diameter larva Mark 6 Tunnel-Boring Machine (TBM) for driving 6000ft of drift.IntroductionKiena Gold Mines is located about 5 miles west of the town of Val d'Or, Quebec, approximately 300 miles north of Montreal. The mine commenced production in October 1981 and has gone through various expansions of ore production with 287 916 metric tonnes in 1982 to reach 453 800 metric tonnes in 1986.Due to the majority of claims being covered by a lake, a grassroots exploration drive of remote areas of the property was required to allow diamond drilling on a yearly basis. High speed sequential excavation methods (SEM) of single heading drifting in the mining industry has not progressed much in the past 20 years despite the advent of electric-hydraulic jumbos, Haggloader and Hagglund type cars. Certain examples of record SEM drifting advances have been performed in the past but only under very specific ground and cost conditions."

Jan 1, 1987

By R. W. Diamond

Introduction THE Sullivan mine and the milling, smelting, and refining operations of the Consolidated Mining and Smelting Company are sufficiently well known to make unnecessary anything more than a very brief account of the events which led up to this Company's branching out into the chemical industry. This development is the result of the 26 per cent sulphur content of the Sullivan ore. Seventy-five to eighty per cent of this sulphur enters the mill tailing, which is stocked at Kimberley. The remainder, contained in the lead and zinc concentrate, is burned off in the first treatments at Trail. Prior to this new development, the sulphur gas was wasted to the atmosphere. In spire of its great dilution with air and discharge from stacks at high elevations above the plant, some damage to vegetation close to the plant was experienced. It had always been apparent that this sulphur should be recovered and utilized if possible, at the same rime relieving, or curing, the smoke nuisance, and constant studies with this in view had, therefore, been maintained. One of the early conclusions reached was that the Canadian prairies would ultimately require large quantities of phosphate fertilizers, as had been the experience of older countries, and that these fertilizers would constitute a large outlet for sulphuric acid which could be made from smelter gases. This conclusion prompted a widespread search for phosphate rock, particularly in British Columbia and western Alberta, with the result that low-grade beds were discovered in the Crowsnest district and to the north therefrom through extensive areas (1). Following these discoveries, an experimental plant was built at Trail for the production of triple superphosphate in order to facilitate field-tests in fertilizing prairie lands.

Jan 1, 1934

By B. Simonian

"The Mount Milligan mine, located in central British Columbia, began operation in September 2013 with a design nameplate capacity of 62,500 dry metric tonnes per day, using a conventional SABC grinding circuit followed by bulk sulphide flotation. Over the last few years, many changes have been implemented in order to debottleneck and optimize the comminution circuit to meet and exceed the nameplate design capacity as well as improve the metal recovery of the flotation circuit. This paper discusses changes, grouped into mechanical modifications, projects, and operational changes. The implementation of these changes as well as ongoing challenges and potential solutions will also be discussed.INTRODUCTION The Mount Milligan mine began production in the fall of 2013. It is a conventional truck-shovel open pit gold and copper mine and concentrator with a 62,500 tpd design capacity copper-gold flotation processing plant. The average head grades for the life of mine are 0.18% Cu and 0.39 g/t Au. At full capacity, the mine produces an average 400 dry tonnes per day of copper-gold concentrate containing approximately 21.5% Cu and 50-60 g/t Au. Current mine life is 21 years. This paper will discuss a selection of the operational, engineering, and administrative changes that have been made at the site since the publication of An Update on Reaching Nameplate Throughput and Continuous Improvement at Mount Milligan (Yue, 2017). PLANT FLOWSHEET CONFIGURATION Run-of-mine ore is crushed through a 60-110 gyratory crusher to a top size of seven inches. Up to 100% of the gyratory crusher product is diverted to the secondary crushing circuit by a moveable gate. The material diverted to the secondary crushing circuit is fed to a vibrating double-deck screen. The screen oversize is placed on a surge pile and reclaimed by four vibrating feeders to feed two 1250 kW standard head cone crushers in open circuit. The screen undersize is combined with the crusher discharge and returns to the conveyor feeding the coarse ore stockpile along with primary crusher product that by-passes the diverter gate."

Jan 1, 2019

By George Delorme

"AbstractThe basic intention of this paper is to present, from a practical viewpoint, a thorough outline of all the sound and accepted principles connected with attaining satisfactory rope performance from multi-rope friction winders.In order to emphasize the importance of some aspects of rope maintenance, a limited amount of hoist rope theory has been included, a s it is felt that without this, some of the more critical, but nevertheless practical, aspects would perhaps pass without full appreciation of their individual merit.It is very much appreciated that many of the maintenance topics and practices discussed herein are already being observed with a high degree of skill among those already involved in modern friction winding. The hope is expressed, however, that the paper will be of additional assistance, and of particular help in introducing sound maintenance principles to those who are moving into this field of operation for the first time.Hoist RopesWITH a multi-rope friction winder system, structural upset within the hoist rope's cross section can occur if the ropes slip in the drum treads. This upset will usually appear at either end of the rope at the tangent point of the drum or deflection sheave with the respective conveyance in the normal uppermost position. This slipping action on the drum causes the outer cover of a Full Locked Coil or the strands of a stranded rope to shift, leading to structural upset. The result very often means that the ropes have to be withdrawn from service before completing their maximum service potential.The cause of any rope slipping in its tread can be associated with a discrepancy in tension of that rope between one side of the drum and the other."

Jan 1, 1977

By X. S. Fan, T. R. Feng, D. Chen

To meet the flotation process requirements, the large-scale flotation cell must be designed for sufficient pulp mixing, reasonable air dispersion and solid suspension, which is very difficult to design for super large-scale flotation cell. Hence, the flotation cell scale-up and optimization for a short period is a challenge for super large-scale flotation cell design. Computational fluid dynamics simulation has been applied in flotation cell study, which is effective, timesaving and low cost in the study of the flow field distribution for super large-scale flotation cell. This paper demonstrates the flow field characteristics in the 600m3 flotation cell by CFD. The flotation cell model is meshed with hexahedral grid and the high mesh quality assures the computational precision. MRF model, namely a steady-state approximation, ensures that individual cell zones can be assigned different rotational speed. Euler-Euler approach is chosen for multiphase flow simulation to treat different phases as interpenetrating continua. Numerical simulation of single phase, two-phase and three-phase are investigated respectively. Results suggested that the flotation cell has the apparent upper and lower flow circulation. In condition of the impeller rotation, the air is dispersed reasonably. In addition, the solid phase volume concentration distribution in the cell has a little difference.

Jan 1, 2015

By John B. Riddell

"AN EXCELLENT review of the status of applied geochemistry was given by Warren (1959) at last year's General Meeting of the C.I.M. The purpose of this paper is to present recent developments and trends. Several important books were announced during 1958: Ginzburg, I. I. Principles of geo-chemical prospecting. (In process of translation from the Russian by V. Sokoloff).Vinogradov, A. P. The geochemistry of rare and zvidely scattered chemical elements in soils. Consultants Bureau, N.Y. Korzhinskii, D. S. Physicochemical basis of the analysis of the paragenesis of minerals. Consultants Bureau, N.Y.In addition to these translations Mason's Geochemistry' has been revised, and Hawkes and Webb (personal communication) are publishing a book on geochemical exploration. A Symposium on Geochemistry was head in Paris in July, 1957, in conjunction with the XVIth International Congress of Pure and Al-lied Geochemistry. The abstracts of the papers presented at this Symposium were published in Geochimica et Cosmocl1imica Acta, 1958, Vol. 14, pp. 150-167."

Jan 1, 1960

By M. W. Wadsley

"Physical and chemical property models are widely used in process engineering. There exist, in the published literature, completely empirical models of ''thermodynamic properties"", that is, property models that are not consistent with the laws of thermodynamics. There also exist property models that purport to be thermodynamically consistent but are flawed in their implementation. There are also published property models that are consistent with the laws of thermodynamics but that do not reproduce property values with an acceptable accuracy. A practicing engineer might be asked to assess very different property models for which there are a variety of claims. This paper discusses features of thermodynamic and empirical property models that may assist in their practical evaluation and implementation."

Jan 1, 2005

By R. W. Bruce, K. W. Downes

"IntroductionSULPHUR production in Canada from all sources for the year 1953 amounted to about 375,000 tons. Except for 16,000 tons of elemental sulphur derived from natural gas, this production was in the form of by-product pyrites, liquid sulphur dioxide, and sulphuric acid. In the same year, Canadian industry imported 359,000 tons of elemental sulphur from the United States. The cost, including transportation charges, to Canadian consuming plants ranged from $35.00 to $45.00 per long ton, depending upon location.Although most of the sulphur consumed is used in the oxidized form it is often most convenient to buy sulphur in the elemental form, and convert it to sulphur dioxide or sulphuric acid in situ as required. This is because elemental sulphur is easily shipped and stored, weighs only half as much as an equivalent quantity of sulphur dioxide and one-third as much as the corresponding quantity of sulphuric acid, and is readily converted to these forms in a sulphur burner. A process, therefore, which could economically recover elemental sulphur from sulphide ores would be most attractive.Since the turn of the century, notable improvements have been made in extractive metallurgy, but until recently only limited attention has been paid to the possibilities of elemental sulphur recovery. This has been due to the plentiful supplies of cheaply mined Frasch sulphur which have been available on the world markets."

Jan 1, 1955

By J. E. Hawley

"The Aldermac copper deposit is in Beauchastel township, Abitibi county, Quebec. It lies about 11 miles west of Noranda. It has been described by Cooke, James, and Mawdsley(2) and by Bruce(3) and has been mapped in detail by W. Samuel and the late K. W. Fritzsche, former Mine Geologist, and by J . E. Gill and A. R. Byers, so that most of the particulars contained in the description that follows are largely the result of the work of others than the writer, whose connection with the deposit, in a consulting capacity, extended over the last 5 years of the life of the mine.According to A. V. Corlett, former Mine Manager, the property was staked during the early winter months of 1923 because of its location adjacent to the syenite intrusive that had been mapped by Cooke near the height-of-land in this township. An examination by Mr. Corlett in 1924 revealed mineralized zones to the north of MacKay lake, and in the vicinity of these K. W. Fritzsche, by dip needle and trenching, discovered the No. 1 and No. 2 deposits, which were both too small and too low grade for exploitation. During the winter of 1925, A. A. MacKay, with a dip needle, picked up a magnetic 'anomaly' in a drift-covered area about 600 feet to the north of previous workings. Trenching here revealed only a narrow zone of mineralization of little consequence, but, farther east, MacKay discovered a more pronounced 'anomaly' over what later drilling and underground work proved to be ore of commercial grade (No. 3 and No. 4 orebodies)."

Jan 1, 1954

By R. G. Helberg, S. M. Rebelo

"Copper and cadmium are removed from the zinc sulphate solution in primary purification by cementation reaction followed by filtration. The solids are sent to the cake leach section where zinc and cadmium are recovered from the copper rich slurry. The copper solids from cake leach are filtered, bagged and sold. In order to achieve a lower cadmium copper cake, an altered process flow is suggested. It is proposed the primary purification be split into two steps for individual removal of copper and cadmium. INTRODUCTIONCopper cake is a product of primary purification, also known as copper and cadmium removal. Copper and cadmium are removed by cementation reaction in four stirred reaction tanks. The slurry is then filtered through Shriver manual plate and frame presses with the solution advancing to the next stage of purification, hot zinc purification (HZP). The solids from primary purification are further processed at the cake leach section where zinc and cadmium are separated from the copper rich slurry. Cadmium and zinc are dissolved in the cold cake leach tanks using spent electrolyte. Cadmium is recovered from this cadmium rich solution by cadmium sponging, leaching and electro-winning circuits. The residue from this cold leach step is further leached using spent electrolyte at a temperature of 85°C. The copper rich solids from hot cake leach are filtered on a drum filter and bagged in 1 ton bulk bags for shipping to buyers.Current assays of copper cake are shown in Table 1. The goal is to produce a copper cake product that is below 0.5% cadmium."

Jan 1, 2012

By Jonathan Peck, Carl Hendricks

"Global Positioning Satellite (GPS) based positioning and navigation systems have been recently developed and implemented by AQUILA Mining Systems Ltd. on blast hole drills and electric cable shovels in Canadian open pit coal and iron ore mines. These systems enable the location of the drill bit or the shovel tracks to be accurately determined in three dimensions. The position of the drill or shovel is displayed to the operator via a real-time, Moving Map Display (MMD) on an LCD-VGA screen. The MMD allows the operator to accurately navigate the drill from blast hole to blast hole or maintain a desired shovel grade or face position, with respect to displayed bench features. The maps for the MMD are downloaded from the mine office via laptop or radio link as required or as mining plans change.To obtain reliable, accurate and real-time3D positions of mobile mining equipment, proven GPS technology has to be utilized. The GPS components need to operate reliably under the severe environmental conditions that exist on board mobile mining equipment. In addition, they have to contend with varying pit geometry’s and satellite configurations, with little or no performance degradation. These issues were initially examined in December1993 during a feasibility project between AQUILA and Gregg River Resources Ltd., in relation to implementing GPS systems on blast-hole drills.To achieve certain design objectives, AQUILA Mining Systems Ltd. has developed navigation systems for cable shovels and blast-hole drills based around off-the-shelf, high precision GPS components. These systems utilize the AQUILA Advanced Monitoring Platform (AMP), to display graphically, via the MMD, shovel grade and drill position to the operator to within ±12 inches of design coordinates. Production prototypes have been installed on a Marion 301 cable shovel and a Bucyrus-Erie49-R Series III drill at the Fording River Mine in August, 1995, at the Wabush Mine on a Bucyrus Erie 190-B shovel in June, 1995, and on a GD120 drill at Gregg River Resources Ltd. in January, 1996. All these systems have undergone field trials to test system components and functionality’s under actual production conditions. This paper will discuss these GPS-based positioning and navigation systems in subsequent sections."

Jan 1, 1997

By N. Birbilis, S. Kairy, C. R. Hutchinson, D. Jiang, D. R. Feenstra, O. Gharbi

"Recent developments in metal-based additive manufacturing (AM) technology have generated considerable interest in multiple industries, owing to flexibility in design and the ability to produce final components in their net shape. The AM of high-strength aluminium alloys has not been widely explored, due to findings of undesirable microstructures leading to short fatigue life and poor fracture toughness; restricting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date. Herein, aluminium alloy AA2024 (Al-3.6Cu-1.2Mg) was additively manufactured via selective laser melting (SLM), with the resultant microstructures and corrosion properties characterised and compared to wrought AA2024-T3. Microstructural characterisation was carried out using transmission electron microscopy (TEM), revealing SLM produced AA2024 included a population of ?-phase (Al2Cu) in preference to S-phase (Al2CuMg) typical of wrought AA2024. Additionally, the corrosion properties were investigated by potentiodynamic polarisation in a range of NaCl concentrations, whilst elemental corrosion rates were also determined (including for open circuit exposure conditions) and quantified in situ with an inductively coupled plasma mass spectrometer coupled with an electrochemical flow cell. Results revealed a significant improvement in the corrosion resistance, and elemental dissolution of AM prepared 2024 relative to wrought AA2024-T3.INTRODUCTION Aluminium alloys remain the preferred candidate materials in applications requiring a balance of low density and strength. The ability to produce net shape components from aluminium alloys has accelerated due to recent developments in metal-based additive manufacturing (AM) technology, including selective laser melting (SLM) and powder bed 3D printing. The AM of Al-alloys, including Al-Si-Mg (namely AlSi10Mg), has become widespread commercially in recent years. Alloys including AlSi10Mg offer reliable and reproducible production by AM, however such alloys (and variants thereof) are not high strength alloys. The pursuit of higher strength AM Al-alloys presents significant merit to multiple industries; however, such higher strength AM Al-alloys have not been widely studied to date. The solidification of high strength Al-alloys during conventional (casting) operations needs to be executed in a manner that avoids so-called =hot-tearing‘, which can arise as a result of the solute type and loading. A report on the solidification of a high strength Al-alloy prepared by AM, along with factors related to solidification, was recently covered by Pollock and co-workers (Martin et al., 2017). It was reported that AM of high-strength aluminium alloys (which have to date been principally based on the compositions of wrought high strength Al-alloys) may lead to undesirable microstructures that reduce fatigue life and result in poor fracture toughness; presently limiting the application of AM to lower strength aluminium alloys (with cast-like Al-alloy compositions) to date."

Jan 1, 2018

By Krishna Parameswaran

"This paper discusses energy use and conservation in the primary copper industry and illustrates eco-efficiency considerations, using select examples of practices at ASARCO LLC, an integrated primary copper producer and others in the industry that promote eco-efficiency. The World Council for Sustainable Business Development first publicized the concept of eco-efficiency at the Rio Earth Summit in 1992. Eco-efficiency is a management concept linking environmental and economic performance and is aimed at generating added value for a business through, among other things, increased resource and energy conservation and reduced environmental impacts throughout the life cycle of the product or service. This concept differs from sustainable development in that focus is only on economic and environmental factors and does not include social considerations. In the metal mining and processing context, this added value can be realized by implementing practices that promote conservation of water and mineral resources, conservation of energy, minimization of waste, reduced emissions and effluents and increased recycling. The examples from the primary copper industry used to illustrate eco-efficiency considerations include: water and energy conservation in mineral processing, adoption of flash and bath smelting processes, emission reduction and process improvement associated with fire-refining, implementation of green chemistry in electrorefining, promoting product stewardship initiatives and fostering renewable energy project on disturbed mined lands.INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, solvent extraction-electrowinning (SX-EW) plants and a copper smelter in Arizona and a copper refinery in Texas."

Jan 1, 2017

By C. Samuelsson, H. Ahmed, B Björkman, A. Andersson

The cost of raw material and energy is a continuing driving force towards working with increasing the recycling of ore based steelmaking residues. In Sweden no on-site sinter plants are operated at the integrated steelworks. Instead, selected residues from the plant are incorporated in a cold bonded briquette product which is recycled to the process via the blast furnace (BF). Since the BF sludge is the major bleed of zinc out of the furnace it is required to be de-zinced prior to recycling in the briquette product. In the present work landfilled BF sludge has been characterized with respect to chemical composition, particle size distribution, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The sludge was also subjected to laboratory scale hydrocyclone trials aiming at reducing the zinc content making the sludge viable for recycling. The results suggested that the sludge had been agglomerated prior to the characterization and hydrocyclone treatment. The zinc removal using the hydrocyclone was discussed.

Jan 1, 2015

By Tapio Leskinen, Jouko Koskinen, Timo Nlltti, Lappalainen Seppo, Pentti Vanninen

"The Courier 300 on-stream analysis system manufactured by Outokumpu has now been in operation at five of the company's concentration plants long enough to give a reliable basis for closer examination of the benefits achieved in control of these processes. The first system was installed at the Pyhiisalmi mine at the end of 1967. Since November 1970, two analyzers have been in operation at Pyhiisalmi feeding the assay data to a process computer which controls the whole plant and does the optimization of the process. In October 1970 the Courier 300 analysis system was installed at S. T. O. LESKINEN J. KOSKINEN the Keretti concentrator of the Outokumpu mine, followed soon by installations at the Vihanti Mine in May 1971, at the new Vuonos mine in November J 971 and at t he Kotalahti mine in December 1971. Since installation of the Courier analysis systems, considerable improvements have been achieved in the control and the economy of the plants. Immediate knowledge of the changes in the process and the possibility for rapid action has resulted in evener production and higher capacity and recovery. The recovery has been increased most significantly at the Vihanti concentrator, which operates on a complex ore. Consumption of chemicals has been reduced at all concentrators. Due to the fact that process control and partly also bilance analysis are not achieved by conventional methods any more, it has been possible to reduce the personnel of the laboratories drastically. Two of the plants, viz. the Pyhiisalmi and the Vuonos concentrators, are computercontrolled. The Vuonos concentrator started operation in January 1972 under computer control from the very beginning. The Pyhiisalmi concentrator has been computer-controlled since 1970. The Courier 300 analysis system was described in detail at the AIME Centennial Annual Meeting (1971). In this paper, less attention is paid to the analysis system. Only the sampling system of the Courier 300 is described in more detail. In the development of sampling equipment, effective use has been made of the company's wide knowledge of the problems involved and the test field offered by its concentrators. The sampling equipment includes secondary samplers and six basically different types of primary samplers, with which most sampling situations can be managed."

Jan 1, 1973

By B. Konda, R. Lauer, D. Camilucci, D. Gladwin

"Income based taxes are significant cost elements to be considered in evaluating investment in new mine development. This paper presents the results of comparative analysis of effective income-based tax rates for mining in the Northwest Territories (NWT), selected Canadian provinces and international jurisdictions. The study was done as background to a review of royalty regulations for the NWT. ObjectiveThis paper presents results of comparative analysis of effective mining royalty1 rates, and combined effective mining royalty and income tax rates on selected mine models for the Northwest Territories (NWT), with those for several other jurisdictions in Canada and abroad which compete with the NWT for mining investment.BackgroundThe February 27, 1995 federal budget directed the Department of Indian Affairs and Northern Development (DIAND) to proceed with a comprehensive review and amendments to northern natural resource management legislation in order “to increase revenues and ensure a fair return to the Crown.” DIAND is responsible for the administration of the Territorial Lands Act, and its regulations.The Territorial Lands Act gives the Governor-in-Council the authority to “… make regulations for the leasing of mining rights in, under or on territorial lands and the payment of royalties therefor,…”. In the NWT, the Canada Mining Regulations (CMR) provide for the disposition of mineral rights for most minerals, other than coal, petroleum and related hydrocarbons, in return for the payment of a royalty to the Crown.As part of this review of the NWT mining royalty regime, several computer mine models were developed and tax regimes in a number of jurisdictions were analyzed. Effective mining royalty rates, and the combined effective mining royalty and income tax rates were compared across the jurisdictions. The results presented in this paper are a part of the background work done in preparing a discussion paper on proposed changes to the NWT mining royalty that is expected to be released for public consultation in the very near future."

Jan 1, 1997

By H. Wotruba, L. von Ketelhodt, M. Kowalzcyk, M. Robben

ABSTRACT Decreasing reserves, water shortages, increasing energy costs, and environmental and social constraints are challenges to the gold mining industry that must be met with innovative machines and methods. This paper introduces the principles of sensor-based sorting and installations that demonstrate the technical and financial viability of the method. The scenarios discussed highlight the potential and advantages of this dry processing technology that requires little infrastructure. Case studies are presented for different ore types using optical- and X-ray transmission–based sorting. Current research is discussed in terms of the potential of near-infrared spectroscopy and X-ray fluorescence sorting for gold applications.

Jan 1, 2013