Search Documents

By Yaniuk DW

The sampling of non-ferrous concentrates from trucks and trains has long been carried out either manually or by automatic spears. Very little use has been made of conventional sampling systems for sampling concentrates at transfer points, or cross-belt samplers for sampling from the belt as the concentrate moves along the conveyor.Due to the high value of base metal concentrates and the often extremely heterogeneous nature of the material it is imperative that the sampling procedures adopted are accurate and precise. The basic principle that all particles in the stream have an equal opportunity to be included in the final sample is not fulfilled by accepted traditional concentrate sampling procedures such as the spearing of wagons, trucks or streams. This may lead to significant bias being introduced into the final sample.Consequently, the application of correct sampling procedures, either with conventional cross-stream samplers or the newer cross-belt samplers, is of prime importance.SGS Australia has recently installed a number of cross-belt samplers for the sampling of base metal concentrates both in Australia and overseas. The application of these samplers will be discussed with emphasis on the benefits of their use.

Jan 1, 1976

By Flierman GA, Van Toor CH

Investigations were carried out of burden distribution using a full scale model of the furnace top. Various charging sequences were used and large differences were found between ore charged as sinter-pellets and as pellets-sinter. These were attributed to the differences in the angle of repose between the two materials. Permeability index was defined which was independent of the driving rate from which a furnace resistance index was obtained for use in weekly reports. Results are summarised as a single expression between blast rates and pressures and the values of Qbl and Qmax are continuously measured to aid the operators in controlling the wind rate in the safe AP region. Results also indicate a reserve in capacity of No. 7 BF.

Jan 1, 1975

By Smith Z, Huppert P, Charbucinski J

The paper describes a spectrometric method and apparatus developed for lithology logging in brown coal formations. The nuclear spectromet- ric technique developed is able to delineate coal/sand/clay seams. One requirement was to log inside drilling rods, as well as cased or open holes. The method described is based on combined natural gamma and gamma- gamma techniques using a spectrometric system for signal acquisition and subsequent computer based on-line data analysis and interpretation.

Jan 1, 1989

By Delahey G, Dunne R

At New Celebration Gold Mine the advent of treating primary sulphide ores resulted in decreased gold recoveries of four to ten per cent. The grind coarsened due to an increase in ore hardness and gold in the residue was found to be associated with pyrite. Finer grinding improved recoveries but was impractical as production rates would have decreased to unacceptable levels. An alternative approach that has proved to be viable combines both gravity separation, to recover the coarse gold bearing sulphides, and then regrinding the concentrate in a tower mill prior to releaching in the cyanide leach circuit. The tailings treatment plant was commissioned in December 1990 and details of the first 18 months' operations are Provided.

Jan 1, 1993

By Wallman D

Since 1981 two single entry roadways have been driven at Ellalong Colliery for a total distance of 1 030 metres. They were driven at a height of 1.73 metres within the 3.7 metres thick Greta Seam using a Dosco In-Seam Miner (I.S.M.). Ventilation of the drivage was accomplish- ed by an exhausting fan in series with steel ducting and flexible ducting in the immediate face area. The air quantities provided at the face were more than adequate to comply with the requirements of -the auxiliary fan rules and the Coal Mines Regulation Act, 1912, as amended. The experience gained in these drivages demonstrated that the ventilation of long single entry headings can be practically and safely achieved using existing equipment.

Jan 1, 1983

The Highlands Region of Papua New Guinea has 3 major national highways. The locations of these national highways are shown in Figure 1. The Highlands Highway begins at Lae City on the coast and passes through the Highlands towns of Goroka, Kundiawa and Mt Hagen. It terminates at Togoba approximately 10km out of Mt Hagen town. The Enga Highway begins at Togoba and passes through the towns of Wapenamanda, Wabag and Laiagam. It terminates at the giant Porgera Gold Mine. The Southern Highlands Highway also begins at Togoba and passes through the major towns of Mendi, and Tari. It terminates at Koroba station, near the Hides Gas Field. Two separate Feeder roads intersecting the main highway service both the Kutubu Oil Project and the Hides Gas Field. These national Highways play a very important role in the development of Papua New Guinea. Goods and services are delivered to the bulk of the population of the Highlands Region using these highways. Heavy machinery and equipment for the mining and petroleum projects of Porgera, Hides and Kutubu are transported using these roads.

Jan 1, 1997

Ore Reserves estimation for the two producing copper orebodies at Isa Mine, Mount Isa, Queensland is discussed. The principal estimation techniques used and discussed are first, a computer based inverse power distance weighted assay meshing technique, and second, a manual arithmetic averaging technique. The principles involved in these techniques are compared, and their areas of application indicated. A general comparison of the estimation of reserves with eventual production is presented.

Jan 1, 1979

By Johns A. L

The concept of the Melbourne Underground Rail Loop and the organ- isation to achieve its construction are covered in the companion papers (Reference 1, 2) and will not be repeated here. The Victorian Railways, as well as being the eventual operator of the Loop when it is completed by MURLA, have also been responsible as "Contractors" to MURLA for the construction of the "cut and cover" or "box" tunnels and related approach works located on existing Railway property. These tunnel connections link the existing suburban system to the new underground works. The following tabulation indicates the significant work volume involved in this cut and cover tunnelling exercise and which is covered in some detail by this paper.

Jan 1, 1981

By Shrivastava P, Humphreys M, Guibal D, Deraisme J

Customer requirements concerning the final products of iron mines are extremely stringent. Because of this, there is an ever-increasing need for mine operators to monitor and strictly control the quality of their product. This quality, as measured by the stockpile grade variability, is the result of a very complex process, where natural characteristics (the orebody and its geology) are transformed through the mining technique (open pit, shovel and truck fleet, blending into stockpile). The only way to reproduce and hence to control the variability of such a system, which is composed of several interactive sub-processes, is by simulation. A complete simulation of a Hamersley Iron Pty Ltd (HI) ore deposit has been undertaken to forecast the impact and cost of various mining methods, mining schedules and product stockpile sizes on variability of chemical and physical characteristics of the products. The mining simulation was made on a conditionally simulated orebody. On a range of criteria, the simulation was considered to fulfil the objectives set and was a valuable aid to analysis of product grade variability, operating and capital costs, selection of equipment, mine scheduling and setting of product grade targets.

Jan 1, 1994

The Blackwater Coal Mine is a modern open cut operation using large draglines for over- :)urden removal and shovels, loaders and trucks to mine and haul coal to the crushing and coal ?reparation plant. Operations at the mine are described in sequence following through overburden removal to the railing of product coal from the mine site. The close operating connection between the mine and washery, which results from the blending of raw coal into clean product via the qashplant bypass system, is stressed. Some features of special interest at Blackwater Mine, such as land reclamation and slope stability,are outlined.

Jan 1, 1974

By Jeffery RI, Pollard CA, Fear NJ

The paper describes the detailed hydrogeological studies carried out prior to the sinking of twin shafts at British Coal's new mine at Asfordby, Leicestershire, UK. The test methods for assessing potential groundwater inflows to the shafts are discussed and details are given of the ground freezing scheme employed through the major aquifer zone in the Sherwood Sandstone at a depth of 375 metres. During shaft sinking pressure recovery tests were carried out to further assess potential inflows and the results are compared with those from the surface tests prior to sinking.

Jan 1, 1988

The mineralogy of regolith material for which whole rock geochemistry has already been done can be used to better understand/rank the significance of geochemical anomalies. Case studies show that the secondary minerals of the regolith environment have quite different capacities to incorporate pathfinder and target elements, eg hematite appears to be a better host to Pb than goethite and Pb rich alunite-jarosite minerals are a better Ag host than mimetite. Thus correlations between elements in regolith material may be strongly affected by mineralogy. Understanding of the significance of a geochemical anomaly is frequently enhanced by knowledge of the weathering susceptibility of different minerals. For example, when a mineralogical sequence which does not correspond to the expected order is found (eg feldspar overlying weathered material without feldspars) it is possible that transported material is present in the profile. Such mineralogical information is particularly relevant as exploration continues into areas of thick regolith.

Jan 1, 1997

By McGuckin P. H

The Cadjebut orebody is a MississippiValleyType (MVT) zinc-lead deposit, and is located approximately 80 km southeast of Fitzroy Crossing in the Kimberley region of Western Australia. It is one of five zinc rich orebodies discovered by BHP Minerals in the region.The participation in the Cadjebut Joint Venture is BHP Minerals limited (Manager), 58 per cent and Billiton Australia Limited, 42 per cent.The mineralisation is contained in gently dipping dolomitised limestone sediments (part of the Lennard Shelf carbonate sequence) with an orebody width of between 60 and 120 m and a strike length of approximately 3 km. The deposit consists of two thin, stratabound shallow dipping orebodies, one overlying the other, to provide discrete but not independent mining areas. The orebody contains approximately 2.1 million tonnes of recoverable ore at an approximate grade of 12 per cent zinc and four per cent Lead.

Jan 1, 1992

By Mousset-Jones P, McPherson M. J

Underground airways are characterized by irregular shape and uneven surfaces including large-scale natural roughness, fractures, and a super-imposed sand roughness. Swirls in the grooves of the wall and separation because of the periodic variation of the open cross sec- tion, due to the blasting patterns, make it almost impossible to calculate average con- vective heat transfer computationally on the bases of the geometrical description of the surface. However, dimensionless friction factors can be used to characterize the surface effect of an airway and an analogy between heat and momentum transfer can be applied to calcu- late an average convective heat transfer Coefficient.

Jan 1, 1988

Hydraulic transport of coal has been used for many years on the West Coast of New Zealand to extract small blocks of steeply dipping coal. Recent development at Strongman 2 Mine has seen the use of high pressure monitors to cut coal and a corresponding increase in the scale of production.This paper provides a brief introduction to hydraulic mining, describes the present system used at Strongman 2 and discusses future potential development.

Jan 1, 1998

The transgressive sedimentary sequence of the Notnnea Basin contains rhyolitic lavas and less voluminous mafic and intermediate volcanims of shoshonitic affinities which erupted simultaneously during the late Cretaceous. The shoshonitic volcanism shows a trend from early inafic to younger evolved intermediate lithologies. The rhyolites are consistently calc- alkaline. There is no evidence of 'mixing, of, the two magma types. The shoshonitic volcanism is the result of a short-lived subduction event related to sprcadime in the New Caledonia Basin and involved reactivation of an earlier Mesozoic subduction zone.

Jan 1, 1995

By Rath M. C, Das R. P

Studies were carried out on dissolution and oxidation of iron powder in ammonia-ammonium carbonate solution using oxygen over pressures. Cobalt and nickel losses during iron oxidation under different conditions were investigated. Regression equations were derived for percent cobalt loss and percent iron oxidation using ammonia, ammonium carbonate and oxygen partial pressure as the variables. The equations were tested for adequacy using Fisher's test. Cobalt losses increased with the increase of initial cobalt concentration and about 400 mg/l of cobalt was lost from a solution containing 500 mg/l cobalt. A maximum of about 80 mg/l nickel was lost from 1 g/l nickel containing solution, and this loss remained the same even when the nickel concentration was increased to 7.5 g/l.

Jan 1, 1992

Comminution Kinetics equations are developed to take into account difference of grindability of mineral components. The equations describing both batch and closed circuit grinding or crushing processes are given. These equations are applied to industrial data to derive comminution kinetic and classification characteristics of the component minerals in a multi-mineral ore. Control strategy based on these concepts is presented.

Jan 1, 1985

By Newell R

The situation in which a gas stream flows through a bed of solids is found in many extractive metallurgy operations. Examples include blast furnace smelting, sintering and pellet firing. In such cases the resistance of the bed to fluid flow and heat transfer is of major significance to the operation of the process. This depends on the structure of the bed, which in turn is influenced by the manner in which the materials are charged to the bed. In this work, packed beds of hematite pellets of two different sizes were prepared in which the pellets were charged as a uniform mixture and in layers. The porosity, flow resistance and heat front velocity were measured and compared for the different bed configurations. For layered beds, the overall porosity and heat front velocity increased while the flow resistance decreased when compared with the values obtained for the uniform mixture. The size of the layers also had an effect on flow Properties.

Jan 1, 1991

By Jensen B, Ofori P, He Y, White E, Stanmore B, Brien M, O&apos

As part of a large AMIRA project, an on-line moisture meter was installed at two mine sites in Central Queensland. This project investigated the factors which control the moisture content of coarse (>0.5 mm) coal from the centrifuges used in conventional coal preparation plants. It was placed immediately after the first centrifuge to isolate the factors pertaining to one machine and its feed.The meter was found to be accurate and precise when compared with manual and mechanical sampling methods. The Grubbs estimator technique indicated that its precision is better than 0.3 per cent at the 95 per cent confidence limit.It has been identified that:1. the variability of the measured moisture contents of coarse coal can be described by normal distributions. Standard deviations of about 0.6 per cent are common; and2. the treatment of the coarse coal on the drain and rinse screens immediately prior to the centrifuge can affect the final moisture content.

Jan 1, 1995