Search Documents

By H S. Welideniya, K Ekanayake

Carbon rich graphite deposits found in Sri Lanka are of inorganic origin and they occur as narrow steeply dipping veins. The vein width of these deposits varies from a few centimetres to metres, with an average vein thickness of 1 m. It is believed that the carbon rich fluid intruded into fracture zones under high pressure and the temperature has crystallised into graphite. This process has also generated many minuscule graphite veins centred on main mineralisation, which has reduced the host rock overall rock mass rating. These discontinuities could also be considered as joints with graphite infill. Graphite mining at Bogala Mines, Sri Lanka is a unique example of narrow vein mining faced with numerous wall stability issues resulting from weak graphite infilled joints.The Bogala vein type graphite orebody has an average vein width of 1 m. Overhand cut-and-fill mining method is used for stoping. The stope consists of two boundary winzes for material handling, access and ventilation. Mining is done on the strike of the vein and the average mining slice height is 2 m. A void to the height of one mined slice is left below the mining level during mining. Waste rock resulting from vein blasting and mine development is dropped into this void as fill rock. Any void height left greater than a single slice height will increase stresses in the stoping zone. This will increase formation of rock blocks and their effective separation from wall rocks. Split miniscule veins occurring around main mineralisation intensifies rock block formation in an environment of mining induced stress release. Consequently, any rock blocks sliding into stopes on graphite infilled joints will behave under constant normal stiffness (CNS) conditions and their shear strength will converge rapidly towards remoulded shear strength of graphite alone. Unlike with general infill deposited in joints, graphite has a very low friction angle and with its slippery nature, a small thickness may affect in great deal to reduce joint shear strength.In addition to immediate filling of excavated voids, controlled vein blasting and spot bolting have improved mine safety. Furthermore, rock bolts connected to each other through iron plates and anchored to anchor bolts installed in non-fractured solid rock are practiced to stabilise rock falls and wedge failures in narrow vein graphite mining. These practices have significantly contributed to safe mining without any rock bursts and catastrophic failures.CITATION:Welideniya, H S and Ekanayake, K, 2012. Challenges faced by narrow vein graphite mining and influence of graphite infill on wall stability, in Proceedings Narrow Vein Mining 2012 , pp 71-76 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By A K. Bayer

When the human eye fails in the evaluation of quality parameters in the extraction of minerals the use of laser-induced fluorescence analysis (LIF) can supply more detailed information on the composition of rocks. On the basis of measurements of selected raw materials engineering concepts for the use of this method in the mining industry as an innovative system for horizon control of mining machines will be described and the most important analysis parameters, influencing factors and interference variables are presented.

Jan 1, 2003

By B Crompton, A Berghorst, G Knox

Laboratory-based dynamic testing provides an invaluable tool in the development of rock bolts for use in highly stressed, burst prone rock masses. While in most cases the laboratory-based test method is not a direct comparison to an in-situ installation due to the purely axial loading and variations in boundary conditions, it does provide an indication of the performance of the tendon system under dynamic loading. The aim of the research described in this paper is to provide an understanding of the effect of the impact velocity of the impact mass during a laboratory-based dynamic test. Understanding the effect of boundary conditions of laboratory testing will improve Geotechnical Engineers understanding of the performance in an in-situ installation. In addition, due to the limited number of dynamic test facilities, an understanding of the effects of the boundary conditions will aid in the comparison of test results for different products from different test facilities. The research was conducted using an impact tester, whereby a known mass is raised to a known height defining the kinetic energy and velocity of the mass at the point of impact with the test sample after release. The impact velocity was varied between 2.7 m/s and 5.4 m/s, while the kinetic energy of the mass was maintained at 11.5 kJ. While a correlation between the impact velocity and strain rate of the system tested was established, due to the properties of the system tested, the range of impact velocity on which dynamic tests were conducted was insufficient to result in a considerable change in the average impact load, the cumulative proximal displacement and the cumulative maximum energy absorbed over multiple impulse. However, due to the reduction in the momentum of the impact mass the impact duration and displacement during each impulse in the series of impulses reduced. CITATION:Knox, G, Berghorst, A and Crompton, B, 2018. The relationship between the magnitude of impact velocity per impulse and cumulative absorbed energy capacity of a rock bolt, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 160–169 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By L Xiong, W J Shi, J H. Wei

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Baizhangzi gold deposit is located in the northern North China Craton. The structural and lithological controls on the location and geometry of orebodies were studied through geologic survey, ore spatial configuration analysis and structural analysis. The orebodies of the deposit comprise auriferous quartz-sulfide veins and disseminated gold-bearing sulfides. The auriferous quartz-sulfide veins are dominantly hosted by the NNE- (and NE- and NW-) trending faults, which are subsidiary structures of the regional NNE-trending F2 fault. The subsidiary NNE-trending faults, having sinistral reverse kinematics, are associated with the sinistral reverse kinematics event of the F2 fault, which happened under a regional S–N-oriented compression stress field. The subsidiary NE- and NW-trending faults appear to be compressive and extensional respectively. These NE- (and NW-) trending faults are restricted to the granite intrusion and are associated with a sinistral strike-slip event of the F2 fault, which reactivated under a NW–SE-oriented compression stress field. It makes significant influence on geological evolution and distribution of different ore types that the strike of the F2 fault presents significant transition from NNE- to NE-trending in vertical. The ore-bearing disseminated host rocks, with widespread silicification and pyritisation, distribute in the lower inner contact zone of the granite intrusion, especially in the lower wavelike boundary of granite intrusion.CITATION:Xiong, L, Wei, J H and Shi, W J, 2015. Structural and lithological controls on the location of orebodies in the Baizhangzi lode gold deposit in western Liaoning Province, China, in Proceedings PACRIM 2015 Congress, pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By P Craig, A Crosky, H Ramandi, S Saydam, H Chen

Frequency of reports on premature failure of rock bolts and cable bolts have increased in past two decades. Such a failure threatens both the safety of underground mine workers and the economic viability of the operations. Herein, we report on analysis of rock bolts and cable bolts failed recently in three underground mines in Australia. Magnetic particle inspection (MPI) and scanning electron microscope (SEM) techniques were used to study the failed bolts. MPI showed a number of subcritical cracks on the surface of the bolts. The majority of the cracks in both cable bolts and rock bolts were initiated from the base of ribs (indentation) where the stress concentration was high. SEM examinations showed tearing topography surface (TTS) in all failed rock bolts and cable bolts. These indicated that the failure occurred through hydrogen assisted stress corrosion cracking (HISCC). The results of this study enhanced the understanding about the failure of rock bolts and cable bolts in underground mines. CITATION:Chen, H, Ramandi, H, Craig, P, Crosky, A and Saydam, S, 2018. Analysis of premature failure of rock bolts and cable bolts failed in underground coal mines, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 407–413 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By T D. H McGrath, G Wardell-Johnson, E A. Oraby, W Staunton, A R. Bax, J J. Eksteen

"Gold ores often show significant inter-domain variation with respect to the gravity recoverable gold (GRG) content and the leach behaviour of the non-GRG component. Liberation assessment is extremely difficult for gold due to its malleability and the high sampling errors and poor test reproducibility resulting from gold’s high specific gravity and the low metal concentrations that occur in most gold ores. The use of microscopic techniques for the liberation assessment of gold is also impractical due to the high number of sampling errors and high cost of analysis.Curtin University’s Gold Technology Group has developed an online carbon-in-pulp/carbon-in-leach (CIP/CIL) simulation model called SIMCIL, which has been used since 1999 to model and simulate industrial leach-adsorption circuits. Recently the model has been upgraded to include an integrated liberation-leach modelling (ILLM) approach, which can be used to evaluate the impact of various process parameters (such as grind size, bleed to gravity etc) and circuit configurations on leach-adsorption circuit behaviour and overall plant gold recovery. A new time-efficient ore characterisation methodology has been researched and developed to provide the required liberation-leach data used in the ILLM approach, which is implemented online for the modelling of gold operations. The ILLM characterisation methodology, test work data analysis, interpretation and application of the ILLM test work data are discussed.CITATION:Bax, A R, McGrath, T D H, Eksteen, J J, Staunton, W, Oraby, E A, and Wardell-Johnson, G, 2016. An Integrated Liberation-leach Model and Ore Characterisation Procedure for Gold Ores, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By S McKnight, L Koroznikova, J Begelhole

"This paper outlines a simple methodology for iron ore characterisation. Iron ores commonly contain a range of iron oxides with varying iron content along with generally minor quantities of lighter silicate gangue phases, giving rise to density variations. Companies tend to rely on heavy liquid separation (HLS) in the evaluation of samples arising from exploration, mining or metallurgical processes. Heavy suspension separation (HSS), a simple laboratory technique of density fractionation, employing suspensions of fine tungsten carbide (WC) particles in lithium heteropolytungstate (LST) solutions, can be used in the evaluation of iron ore.As part of Arrium Mining’s program to improve its knowledge of ore types being processed in two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed and geometallurgical evaluation for the OBPs has become a major focus.Metallurgical evaluation of the hematite ore ultra-fine size fraction, formally treated as waste but now upgraded by HSS, is a part of Arrium’s program to improve recovery.The HLS method for iron ore characterisation is not generally used as part of routine iron ore feed metallurgical evaluation due to the expense, toxicity and time-consuming nature of the technique. Results show that the HSS method for iron ore characterisation can achieve low-cost, low-toxic separation and can be used on-site to improve turnaround time of results (Begelhole, Jasper and Koroznikova, 2013).Arrium have applied this technique successfully for the past three years to progress process improvement for the two OBP as well as to assist Arrium’s on-site laboratory services, Bureau Veritas in Whyalla.The main objective of this program has been to further develop the HSS procedures using a low-toxicity, high specific gravity (SG) suspension; LST and WC as the dense medium for metallurgical evaluation of ultra-fines.A suspension of a particular density will separate iron ore into two products: a sink fraction (denser iron oxide – hydroxide particles) and float fraction (silicate – iron ore composite particles). A theoretical grade and mass recovery can be calculated, and a grade – mass recovery curve can be constructed for iron.Metallurgical evaluation of the plant feed ultra-fine size fractions are used to improve efficiency of an upgrading plant process. This type of characterisation can be used to prepare feed piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved.CITATION:Koroznikova, L, Begelhole, J and McKnight, S, 2016. Characterisation of Low-grade Hematite Ore Ultra-fine Size Fraction Particles by Heavy Suspension, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 327–334 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

By Szwedzicki T, Jiang J

The acoustic emission (AE) technique has found wide application in rock engineering. Generally, acoustic emission, which is produced by a rapid microcrack growth, is an ubiquitous phenomenon associated with brittle fractures and can provide information on the failure process in rocks. The sudden release of stored energy in the form of an elastic stress wave that travels from the point of origin within the material to a boundary is called an AE signal or a discrete AE event. Based on a number of experiments and analysis, the correlations among the rock type, the complete stress-strain behaviour, mode of failure and AE properties are investigated and the AE pattern has been classified as four types: single-peak AE, double-peak AE, continuous AE and absent AE. Each type of AE pattern corresponds to a certain type of rock and is largely related to the internal structure and imperfection of a rock. Applications of the AE technique in stability monitoring, in situ stress assessment and seismic source location are also discussed.

Jan 1, 1995

By H J. J Boshoff

Pit lakes, as a final void after completing open cut mining, are in most cases unavoidable. Initial mine designs and approvals require consideration and assessment of closure objectives, legislation and stakeholder acceptance to ensure suitable understanding of the closure liability. Mining companies undertake studies and engineering during the planning, operational and closure stages of mining to identify closure options for the final voids, which would be sustainable. Without adequate planning prior to and during the life of the mine, options during the closure stage become limited resulting in costly closure works or long-term liabilities. Engineering consultants provide a specialist service in the assessment of long-term pit lake water levels and characteristics. Ongoing advances in mining methodology and technology, coupled with improved data collection and data management aid in a better understanding of the complexities in estimating long-term pit lake water levels and characteristics. Closure objectives developed during the planning stage sets the requirements for long-term pit lake water levels, which could require maintaining a water level and pit water or discharge water quality. A variety of approaches could be used to assess these closure scenarios each requiring specific data and methodologies. Typically, limited data is available during the planning stage, which results in assumptions based on past experience and relevant case studies. Closure assessments are revisited during the life of mine and leading up to the closure stage, during which additional site-specific data is available improving the accuracy of the assessments.CITATION:Boshoff, H J J, 2018. Assessment of approaches, data requirements and methodologies for estimating long-term pit lake water levels, in Proceedings Life-of-Mine 2018, pp 28–31 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By W D. Rech, K W. Keskimaki

As an integral part of the conversion from rail haulage to conveyor haulage at Henderson, over six kilometres of drifting and several large complex openings were mined. The deepest of these areas was nearly two kilometres beneath the surface, bringing all of the challenges of rock stress and heat that come with mining at these depths. Though many mines operate at these depths, the development of the infrastructure necessary to support a 36 000 tonne per day caving operation brought some unique challenges to the development mining activity. The issues handled include: finding experienced staff for a æfast trackÆ development program; rock bursts and ground conditions; inflow of 50 degree centigrade water; acceleration of the project completion; large diameter raise boring and difficult muck handling.

Jan 1, 2000

By B Cook, M Karakus, J Light, E K. Chanda

The aim of this research is to develop a model through which the appropriate paste recipe parameters, for example solid content and cement content, can be derived given the stope specific requirements such as stope dimensions, required strength and curing time. A large number of samples and uniaxial compressive strength (UCS) tests were conducted at the Angas Zinc Mine (AZM) paste plant and testing facility. Samples were varied in tailings solids content, cement content and sand content. The results of this testing were modelled to determine the UCS relationship to each of the parameters. The output of this modelling was an easy-to-use program that outputs the design mixture given the stope dimensions and required stope backfill-curing time. This allowed flexibility within the mining schedule for curing times of cemented paste backfill stopes. The optimised schedule using the stope specific mix design, when compared to the standard 14-day curing time used previously, resulted in a smoother weekly mine production schedule. For the modelled 12-week period (one quarter) the 14-day curing time would result in an eight-day shutdown of the mill. The cost for each shutdown is in the order of $125 000/d. Due to the unique nature of each mine’s tailings, this exact outcome would not be directly applicable to another paste fill site. However, the process in this report could be followed for another site to achieve a system similar to the output of this project. This would ultimately lead to a more optimised backfill and stoping cycle and a more optimised mine.CITATION:Chanda, E K, Karakus, M, Light, J, Cook, B and Harris, A, 2014. Optimisation of the paste fill cycle at Angas Zinc Mine, Strathalbyn, South Australia, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 259–264 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By M Rea, E O’Connell

Decarbonising explosives manufacturing and catalysing low-carbon mining supply is a significant global challenge. Low-carbon manufacturing precincts – clusters of geographically close businesses across multiple industries that share a goal of adopting firmed renewable energy and decarbonising process emissions – offer one potential solution. In an Australian first, Orica commissioned tertiary catalyst abatement technology in 2023 to mitigate greenhouse gas (GHG) emissions at its Kooragang Island (KI) facility in New South Wales (NSW), Australia. The EnviNOx® technology (ThyssenKrupp Industrial Solutions AG, Dortmund, Germany) used reduces nitrous oxide (N2O), a potent greenhouse gas arising as a by-product of nitric acid manufacture. As a result, mining customers in NSW are now benefitting from ammonium nitrate (AN) products that are almost 50 per cent less emissions-intensive than those Orica previously offered. The $37 million project is a private-public partnership that has involved partners across Federal and State government, global engineering and technology vendors, local community groups and local carbon advisors to overcome financial barriers.

Sep 1, 2024

By B Howard, M Jones, D Pershke

"Current closure objectives and criteria are often difficult to achieve and are not delivering value for money outcomes at closure. Current mine closure processes tend to focus on rehabilitation and revegetation of landform structures to as close to premining condition as possible, rather than focusing on the functions of those structures and values they provided. Because mining has highly disturbed the environment, premining conditions and vegetation are often not achievable and objectives and criteria aimed at achieving close to these conditions have been shown to be very costly.The authors have developed a broader approach to developing mine closure plans that is based on environmental risk and gaining post-closure social, environmental and economic value. We think the focus should shift from trying to return the original landscape to returning functions and values provided on- and off-site. If it is not possible to return values on-site in a cost-effective manner, investment should be provided to deliver equivalent values elsewhere.This process can provide better stakeholder acceptance, deliver better environmental outcomes on the tenement and within the catchment and significantly reduce costs, whist fulfilling closure obligations.This framework should enable closure teams to: focus on the functions and services that are important to achieve as outcomes post-closure, rather than a focus on revegetation and replacing the premining biophysical structure engage meaningfully with stakeholders regarding closure outcomes and link outcomes to stakeholder values conduct transparent option evaluations that enable stakeholders to clearly understand the costs and benefits associated with each option and to participate in dialogue on option selection.We present examples of how the framework could be applied to identify alternate closure options that achieve equivalent value outcomes while reducing the costs of closing the mines.CITATION:Howard, B, Pershke, D and Jones, M, 2014. Achieving better mine closure outcomes for less money, in Proceedings Life-of-Mine 2014, pp 615–620 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 16, 2014

By Coates D. F, Neil T. J, O&apos

A proper economic analysis of pit slope design must reflect the trade-off between the benefits and the increased risks of slope fail- ure inherent in steeper slope angles. However, no formal framework for a proper analysis existed to date. This paper describes the results of the past four years' effort in which a formal eco- nomic analysis framework was developed and tested through a case study. This framework, in essence, consists of the availability of tested procedures and com- puter programs. The procedures as well as the programs are divided into two broad functional categories; (1) the first category related to assessing the economic benefits and costs associated with various pit slope angles and (2) the second category that determines the overall financial impact which the assessed benefits and costs exert to the mine operator's overall economic stature.

Jan 1, 1977

By Moritz P

Thiourea has been recognised for a long time as an acid-stable complexant for gold. Generally, the use of thiourea has been shown to exhibit enhanced leaching kinetics compared to cyanide but suffers the disadvantage of excessive reagent consumption. Thiourea leaching is particularly com- patible with the extraction of gold from refractory ores. This is due to the need for an oxidative pretreatment to liberate the gold. Such pretreatments typically result in the production of an acidic residue. The application of novel thiourea leaching technologies to the extraction of gold from a bioleached pyrite concentrate was investigated. The interac- tion of leach variables with thiourea consumption and gold extraction was established. An economic assessment of thiourea leaching was compared with conventional cyanidation. The results indicated that gold leaching of the bioleached residue using thiourea compared very favourably with cyanidation.

Jan 1, 1991

Orebodies in the Mt. Charlotte-Hannan's North area N. and E. of the town of Kalgoorlie provide a marked contrast to the pyritetelluride lodes of the Golden Mile, although both groups of orebodies appear to be fundamentally related.These highly siliceous telluride-free orebodies N. of the Golden Mile are closely related to strong oblique faulting. The Golden Mile lodes, while possessing an apparent overall relationship to the oblique faults also have a close relationship to E. dipping strike faults.INTRODUCTIONThe Mt. Charlotte-Hannan's North area lies N. and E. of the town of Kalgoorlie and is separated from the Golden Mile by the Golden Pike fault. The orebodies discussed lie in an area approximately 3 miles long by 1 mile wide (Fig. 1).The area includes the site of the original discovery of gold in the Kalgoorlie district in 1893. There have been numerous mining operations over the years, the bulk of the production coming from two orebodies, Mt. Charlotte and Hannan's North. These have provided approximately 900,000 tons of the 1,100,000 tons of ore mined in the area.Production to date from the principal orebodies in the area has been as follows.1. Hannan's North orebody, 582,000 tons of ore for 275,000 oz of gold2. Mt. Charlotte orebody, approximately 230,000 tons for 75,000 oz3. Pharlap and Golden Goose orebodies, each orebody approximately 8,000 tons for 2,700 oz4. Maritana Hill orebodies, approximately 170,000 tons for 70,000 oz...

Jan 1, 1965

By Pak DL

Over the last decade computers have become an essential element in assessing the economic feasibility of mining new mineral deposits and in assisting a variety of related support functions. A broad overview is given of the many technical application areas where computers are contributing to the mining industry with reference to work being done on the evaluation of drill hole information, mineral inventory modelling, ore reserve estimation, financial analysis, process simulation, process control, workshop job scheduling, PERT applications, and com- puter aided drafting. In all these areas the computer has greatly reduced the manual effort involved in looking at alternatives. It has had a significant effect in eliminating delays in revising calculations, or rescheduling activities to incorporate new data or cater for changing conditions, while at the same time providing more accurate and prompt information for the management decision making Process.

Jan 1, 1980

By L W. Palmer

"Evaluating the geological risk associated with ore deposits is becoming common practice in the mining industry. While geostatistical simulation is a useful tool for evaluating this risk, the effect of applying different types of simulation is less understood. For simulation of categorical variables like rock types, available methods perform simulation in fundamentally different ways. In this study, the geological risk relevant for informed mine planning is studied with two categorical simulation methods, PluriGaussian Simulation (PGS) and Sequential Indicator Simulation (SIS). Risk is expressed as a probability of repeated occurrence of lithological units in the same location across simulations. Significant differences are observed between the methods in terms of spatial distribution of risk. To identify the most plausible risk model, the input parameters at every step of both techniques are scrutinised. PGS and SIS inputs are classified as four parameters that are: fundamental to implementation of the methodfixed to enable comparison of PGS and SISdetermined by user interpretation, hence variablenormally optimised during application of PGS and SIS. The effect of parameter selection from categories 1 and 4 on the risk model is investigated using drill core data from a leucogranite deposit. A corresponding block model is created for assigning outputs from PGS and SIS. Risk models produced by either method are illustrated in a cut-out from the block model to enable bench-by-bench comparison. For PGS, risk associated with relatively rare lithologies is relatively sensitive to variation of parameters. Independent of the abundance of lithology, a location-dependent effect of variogram and vertical proportion curve parameter selection is observed, with risk increasing towards the deposit edge. Although SIS requires fewer inputs, single lithologies must be modelled in turn. Using small numbers of samples in the search neighbourhood, all risk models differ substantially. For larger numbers of samples, the risk models are similar. Overall it appears that the risk model produced using SIS is less sensitive to changes than PGS but further work is required to confirm this.CITATION:Palmer, L W and Glass, H J, 2014. Risk associated with rock type prediction using simulation techniques, in Proceedings Ninth International Mining Geology Conference 2014 , pp 217–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By Q Zhuo, P C. Pistorius, M N. Al-Harbi

A likely increasingly important pathway for future low-carbon ironmaking and steelmaking is the combination of gas-based direct reduction with electric furnace steelmaking (DRI-EAF route), or with electric smelting (DRI-ESF route). In the DRI-EAF route, the gangue that is present in the iron ore is fluxed and removed as slag in the melting (steelmaking) step. This is in contrast with integrated steelmaking, in which the gangue is removed as part of blast furnace ironmaking. For DRI-EAF steelmaking, the amount and composition of slag depend on the iron ore composition, flux additions and iron yield. Slag volume and composition affect phosphorus removal, foaming behaviour and the process energy requirements. In this work, heat data from a year of DRI-EAF production was analysed to test whether the expected relationship between slag volume and electricity consumption for EAF steelmaking was observed. The data include slag analyses (one sample per shift), and heatlevel information on all inputs, final steel temperature and dissolved oxygen concentration, electricity consumption, tapped steel mass and tap-to-tap time. In analysing the data, the slag volume was estimated from the assayed slag CaO concentration and CaO inputs to the EAF. The expected effect of slag volume on steelmaking energy consumption was calculated with a mass and energy balance, considering the heat of mixing of the slag. The calculated energy requirement of slag formation is in line with previous estimates reported in the literature.

Aug 21, 2024

The An Shan iron ore deposit is the biggest low-grade oxidised iron deposit in China. Over the past ten years, about 120 SLon verticalring-pulsating high gradient magnetic separators units have been installed in An Shan to process oxidised iron ore. This paper describes how several plants have upgraded their old technologies to new technologies with SLon magnetic separators as the key equipment for controlling tails grades, including using reverse flotation as the key technology for iron concentrate cleaning, These plants have been modernised with beneficial results at low cost.

Jan 1, 2009