Search Documents

By W. J. Mcgaughey

A crosshole seismic imaging (tomography) experiment has been carried out in an underground mine in order to delineate waste rock within a massive sulphide ore body. Data comprising 1526 travel time measurements were inverted to yield a compressional wave speed image consistent with, and adding to, knowledge of the extent of the waste inclusions. An effective method of resolving travel time discrepancies measured on reversed ray paths is presented.

Jan 1, 1989

By Edgardo Orderique

Southern Perú Copper Corporation ha desarrollado un programa de reevaluación de las reservas para optimizar cada etapa del proceso y así llegar a las reservas mencionadas. En este sentido, el presente texto desarrolla el esquema de optimización de una secuencia anual de minado. El proyecto comprende la realización de de perforaciones en zonas llamadas geometalúrgicas, con el fin de realizar pruebas metalúrgicas y definir el comportamiento del mineral en la concentradora y lixiviación. También se incorpora el concepto de índice de solubilidad, parámetro que sirve para diferenciar adecuadamente un mineral económico para flotación del de lixiviación y finalmente, se optimiza la secuencia anual de minado y disposición de material en botadero. En consecuencia, es importante determinar el uso de software y hardware adecuado para planeamiento de minado, ya que depende de la magnitud de la mina como en el caso deCuajone.

Sep 13, 2001

By Klaus Pöllath

This paper describes mitigating measures and the design of compensation grouting which will be executed from deep shafts of the Amsterdam North/South Metro line project. Due to the specific conditions for TBM-tunnelling in Amsterdam (historical buildings on pile foundations near the tunnel and soft soils with high groundwater levels) tunnel construction necessitates mitigating measures, such as compensation grouting or soil freezing. Züblin developed a special shaft construction method for critical distances to buildings. For the compensation grouting Züblin developed a new software tool, called SOFIA, which controls and visualizes and thus optimizes the entire injection process. This tool significantly increases the efficiency of the injection works while reducing the geotechnical risks.

Jan 1, 2006

By Gene Mattila, Ron Boyd

Introduction Rock bolting is a general term that encompasses pinning, roof bolting, rib bolting, and cable bolting. Rock bolting contributes the highest nonproductive cost and is the most significant safety risk in mining today. Total installed bolt costs are now more than $20 per bolt. Rebolting or repair work doubles this. And bolting accidents account for about 30% of all fatal and nonfatal lost time accidents. It is only logical, then, for the mine operator to install the highest quality anchors possible. Every bolt on the market - tensioned, untensioned, full contact, or point anchor - has designed capabilities in axial, shear, and fluctuating ground conditions. Bolts will provide a designed support if material specifications and installation procedures fall within the manufacturer's recommendations. This also assumes that there are no unexpected geological or operational changes. Proper material specifications and installation procedures should guarantee the mine operator a quality anchor. To help assure this, the Mine Safety and Health Administration (MSHA), the US Bureau of Mines (USBM), and the AMC Manufacturers group developed stringent ASTM materials standards. These govern mechanical point anchor bolts and bolts using threaded and nonthreaded rebar. There are also minimum standards that suppliers must comply with in the manufacture of frictional bolts. However, most frictional bolt standards are based on the manufacturer's own specifications. It would be impossible to set uniform regulations on frictional bolts. Each bolt provides support in a slightly different manner and thereby requires different material needs. Quality Control In any case, material quality can generally be assured through tight order specifications and periodic quality control checks. The problem with installing quality anchors does not solely lie with the material. It includes all the events that occur from the time a bolt leaves a manufacturer to the time it is installed. The anchoring ability of any major type bolt can be affected by transportation, storage, mechanical performance of installation equipment, installation demands of the operator, proper drilling accessories, and local geology. Table 1 and Fig. 1 document the negative events that can affect each bolt and the degree to which it can be affected. Drilling a hole of oversized diameter, for example, is an operator controlled factor. It will adversely affect most bolts. An over-sized diameter reduces, or even eliminates, the anchorage capability of a mechanical shell. It will reduce the support capacity of a split set to nearly nothing. And it will cause a partial or incomplete grouting around the resin bolt. Frequently, due to bit wear, holes are drilled undersized in diameter and may not be properly cleaned out. In this case, it will be difficult for the operator to push the mechanical shell into the hole, thereby causing him to drill another hole. In cases where the bolt is obviously not providing anchorage, operators will probably drill another hole and place another bolt. Rock Bolt Regulations It is the situations where a bolt is improperly installed in the hole, but gives the appearance of a good bolt, that are frightening. In fact, some safety officials and engineers believe that only 50% to 60% of installed bolts are working. These bolts cause irregular ground load transfers in other bolts and overload them. This causes hazardous situations and overstressing. It is these bolts that fail prematurely 200 to 255 mm (8 to 10 in.) behind the face and possibly contribute to the high accident rate. The government and several manufacturers recognized the need to check the integrity of rock bolts. These programs are in different stages today. Tight torque regulations have been established for mechanical

Jan 4, 1985

By M. C. Bhulose

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The purpose of this project was to identify constraints that could occur in the current sub-decline shaft at Turffontein Shaft should an increase in production take place. Particular attention was to be paid to the transportation of men and materials and to the broken rock and ventilation capacity of the shaft. This project is an in-depth evaluation of the logistic capacity of the sub-decline system at Turffontein Shaft in order to determine by how much production can be increased in this area to replace tonnages from the vertical shaft area, where ore reserves are rapidly becoming depleted.

Jan 1, 2004

By J J. McEwan

Silver tarnishes readily in common atmospheres and is accelerated in humid atmospheres. Tarnish is the formation of silver sulphide on the surface of silver when it is exposed to a wide range of sulphur-containing atmospheres. Tarnish is unattractive and highly undesirable, and can be removed either with a silver polish or a chemical dip. Dips are generally only recommended when heavy black tarnish cannot be removed with a polish, and care must be taken during cleaning because these can contain aggressive chemicals and give off hazardous and unpleasant smelling fumes. Polishes work best for large areas of plain undecorated silver, and form part of a regular cleaning programme. Some polishes contain chemicals that inhibit tarnishing, but these generally only have a short life. Several methods have been developed to reduce tarnish formation on Silver; these include alloying, surface treatment, and coatings. The authors evaluated a range of self-assembled monolayer (SAM) surface treatments and coatings in earlier research. Four treatments/coatings increased the time to noticeable tarnish by more than ten fold, and the results were reported at the International Corrosion Congress (ICC) in 2005, and at the Mint Directors Conference (MDC) in 2006. SAM treatment using 95% 1-hexadecanethiol (C16H34S) was found to give good anti-tarnish performance and showed potential for the commercial treatment of Sterling silver. Therefore research was performed to optimise the methods of application of this type of coating to provide an easier, faster, and more-user friendly technique to provide an anti-tarnish treatment. Keywords: silver, tarnish resistant coatings.

Jan 1, 2006

Kidd Mine in Northern Ontario is now producing from Stage 1 of the Mine D expansion project ? mining between 2100 m and 2700 m below surface. Planning for Stage 2 of the Mine D project is already well advanced and will see the mine extended potentially to 3100 m below the surface. To ensure adequate ventilation is maintained at such depths, two large axial fans have been installed on the 6000 Level (1800 m below surface) as exhaust booster fans to operate in series with the surface exhaust fans. The Kidd Mine 6000 Level Booster Fans are a unique installation with unique and often unexpected challenges. These challenges have been met and attacked through the combined efforts of mine and fan manufacturer personnel with a common focus.

Jan 1, 2009

By AIME AIME

T HE Institute of Metals Division and the Iron and Steel Division will meet jointly at the Stevens Hotel, Chicago, during the week of the American Metals Congress, Sept. 22-26. The Iron and Steel Di- vision of the American Society of Mechanical Engineers, the American Society for Steel Treating and the American Welding Society meet at the same time. but the sessions have been arranged to conflict as little as possible. A rich program of papers and plant visits has been arranged for the members and guests of the two Institute Divisions. The annual dinner and a pro- gram of entertainment are being arranged by the Woman's Auxiliary of the Chicago Section. Members are urged to register immediately up011 arrival and to make dinner and plant visit reservations at the same time.

Jan 1, 1930

By Nicholas Enraght – Moony, Alvin Johns, Zhonghan Zhang, Zhang Xianhua, T. Choo

"The tungsten (WO3)-rich ores from King Island Scheelite (KIS) Mine, Australia, containing scheelite(CaWO4) were previously recovered by gravity separation and flotation of fine scheelite (1978-92) with an overall recovery of 76% when both circuits were operating. Recently extensive test work has been conducted both in China and in Australia on KIS ores, assaying from 0.50%-1.34%WO3, and tailings assaying 0.2%WO3(GZRINM 2009; 2011a; 2011b). A new approach, which aimed at improving both recovery and grade of concentrate by means of an innovative all flotation route WOF (Whole Ore Flotation), achieved excellent results: 90%-92% recovery to concentrate grade of 66%-70%WO3for the ores. The process is characterized by the use of selective reagents in flotation, including a newly developed collector for scheelite, GYWA. The WOF process also embraces the "Improved Petrov Method" in the cleaning of scheelite rougher concentrate. Earlier investigations found that the removal of sulfides by flotation prior to scheelite flotation was not necessary. It was also found that recycling of process water did not influenceresults. Two main ore types were tested as well as tailings from 2009to 2001(0.20%WO3). In addition a flow sheet using wet high gradient magnetic separation (WHGMS) in tandem with flotation was also investigated for the tailings."

Jan 1, 2014

For the purposes of this discussion it is assumed that contributors should express the thoughts that arise from their personal experience. So wide is the range of mineral deposits, and so varied the methods employed in their discovery and development, that no two geologists are likely to have been impressed with the same applications of their science. The author's own personal experience has been, during recent years at least, very largely concerned with the broader aspects of the employment of scientific method and geological knowledge to the problems of exploration and exploitation, for the guidance of the general public and governmental authority rather than of mine executives and directors. The view-point thus reached is likely to differ in many respects from that of men who are much more intimately concerned with the mining problems of a single metal or a single mining field, and for this reason a statement may perhaps supplement those from others whose experience has been markedly different.It may well happen that, at some not distant date in the future, when systematic and comprehensive instruction in economic geology is embodied in the courses- prescribed for mining engineers during their years of training, the author's comments will be quitesuperfluous; but at the present time they appear to him to call for expression.The Need for Training of Mining Men in Economic Geology.Contact over a period of many years with mining men who have had different kinds of training and experience has been convincing that there is a general reluctance to acquire a full rational understanding of the geological factors involved in exploratory and developmental problems. The correction of this attitude is regarded as vital to the industry and it is necessary to insist that the outstanding requirement of the present day is the utilization of all branches of geological, investigation in the field and the laboratoryby men who have had systematic and specialized training in these matters. The science of geology is many-sided, but is, nevertheless, whole and essentially indivisible. No one can afford to disregard any fraction of its content 'or any of its methods of investigation.The greatest advances have been made in the understarnding of the occurrence of mineral deposits by those whose knowledge Qfbasal principles, has been soundest, whose endeavour has been to ascertain all their relationships in space and time, whose attention to detail of all kinds has been keenest, and at the same time, whose capability to distinguish between major and minor features has been most marked.With the passage of the years and the accumulation of data from many lands, it has been possible to build up a great body of information regarding the primary deposition and secondary alteration of mineral occurrences, which is of the utmost value in guiding thesearch for new deposits to take the place of those that become exhausted. This heritage is due not only to the efforts of gifted in...

Jan 1, 1950

By Raffaella Granata

The paper deals with the remediation of two areas formerly utilized for the disposal of hazardous wastes in a petrochemical plant. The works, designed on the basis of the criteria of maximum safety and minimum environmental impact, consisted in the confinement of the contaminated soil and groundwater within surface caps and perimetrical cut-off walls embedded in the underlying clay layer. The cut-off wall is 0.8 m thick and has a maximum depth of 33 m: it was designed to guarantee, as a minimum, the level of safety for a landfill for hazardous wastes, in accordance with the applicable National Standards. It was constructed with self-hardening mud and with the installation of an HDPE geomembrane. The HDPE liner of the cut-off wall was then sealed to that of the capping to obtain the complete encapsulation of the contaminated soil. A system of piezometers allows the monitoring of the cut-off efficiency measuring the fluctuations of the groundwater table and testing the chemical contents. Some wells installed within the contaminated areas will contribute to guarantee the full efficiency of the system in case of state of emergency, controlling the water-table level inside the confined areas.

Jan 1, 2006

By S. Prasad

The effectiveness of ultrasonic velocity measurements and attenuation of the propagating pulse was evaluated as a means of Non-Destructive characterization of cold worked and annealed copper. Commercial copper is subjected to mechanical working such as forging, rolling and thermal treatment to induce re-crystallization. The microstructural changes that occur in copper and a variation in its mechanical properties are subjected to analysis using the ultrasonic technique. The signal processing is carried out using the wavelet analysis technique. The features of wavelet analysis namely, localization in space and the presence of an infinite set of basis functions allows removing noise from the time series and components of a non-stationary signal to be analyzed. This is seen to improve the accuracy of the results obtained from the ultrasonic technique in the case of copper, which has distinct coarse grains that are difficult to inspect due to backscattering from the grain boundaries.

Jan 1, 2010

By Radianto Elprama

For the realisation of the underground railway line RandstadRail in the city area of Rotterdam a bored tunnel is under construction. Diaphragm walls up to a depth of about 40 m were used to construct the building pits for the start shaft, the Blijdorp Station and the end shaft. The water tightness of the diaphragm walls was determined by leakage tests that were executed after the construction of the walls, but prior to the excavation of the building pits. The tests showed satisfactory results with a hydraulic resistance of the diaphragm walls of at least 500 days. To determine the water tightness of diaphragm walls it is recommended to follow the specific procedure as described in this paper.

Jan 1, 2006

By Luis Haro

Puesto que el deslizamiento de relaves constituye uno de los principales riesgos para la vida y seguridad de los embalses, se desarrolló un programa que rehabilite los depósitos de los relaves a través de los gaviones y geomallas como elementos que estabilizan los relaves descargados. En este sentido, el uso de geosintéticos revolucionó el diseño de los relaves y sistema productivos y permitió un mejor manejo ambiental de los relaves. Asimismo, la utilización de gaviones como paramento externo en el sistema suelo armado, otorga mayor rigidez al mismo en el caso de paredes, taludes más verticales, drenaje y protección contra la erosión. En consecuencia, el uso de gaviones y geomallas es aplicable para la construcción de depósitos de relave y estabilización de depósitos inactivos.

Sep 13, 2001

By Richard A. Cubeta

Precast concrete segments have been used in sanitary sewer tunnel design for decades. Federal mandates (reduction in heavy metals and I & I), and system design changes (increased retention times) and other factors have exacerbated corrosion problems. In an effort to combat the ever-growing effect of microbiologically induced corrosion, owners, engineers, and designers have been specifying thin-film lining systems to protect precast concrete segments. These systems have compatibility and installation issues. Chemical additives or calcareous aggregates have been utilized in precast concrete, but have only proven to retard the rate of corrosion and do not eradicate the problem. Solid cast polymer segments are stronger than precast concrete, do not require linings or coatings, are impervious to ground water infiltration, and, above all, are inherently corrosion resistant through and through.

Jan 1, 2008

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By Ramin Motamed, Joseph A. W. Toth

Evaluation of the capacity of large-diameter drilled shafts using current load test methods present challenges when considering the magnitude of loads required to fully mobilize their capacities. Often, these full scale tests do not fully mobilize the capacity through side resistance. Therefore, the need for innovative solutions to extrapolate side resistance and interpret nominal capacity are of key interest. In this study, we evaluate three methodologies for extrapolating unit side resistance based on bi-directional load test data. Fellenius (2001) presented these methods for interpretation of pile capacity using static load tests. Our interpretations are based on the evaluation of 116 load tests. Unit side resistance was calculated and reviewed for each load test and categorized using three criteria of mobilization; (A) full, (B) partial and (C) linear. This study specifically focuses on load tests that showed fully mobilized unit side resistance behavior (Criteria A). The three methodologies were applied assuming Criteria (A) load tests were mobilized to 50% of their measured values. Subsequent comparisons of each extrapolation were then compared against the full measured values for each test and generally showed good agreement. INTRODUCTION It is widely accepted that conducting load tests such as standard top-down tests or bi-directional (i.e. O- cell) tests can help designers understand load-settlement behavior and the nominal resistance of drilled shaft foundations. These load testing methods provide the advantage of confirming design assumptions as well as improving the reliability of the foundation design. The potential cost savings from the application of these methods for mid to large size projects is self-evident. For example, in a recent project in Northern Nevada, an O-cell test on a 6.9 ft diameter, 114.8 ft length drilled shaft imposed an initial cost of $125k to the project, resulting in a 15% reduction on the total foundation cost; equivalent to $1.3 million in overall savings (Pease, 2014). However, the costs of implementing such methods on smaller projects can be prohibitively expensive (Hagerty et al, 2016). Despite the clear advantages of drilled shaft load testing, the current practice is not without limitations. Performing load tests on large-diameter drilled shafts with high capacities is a challenge considering the significant loads required to fully mobilize the capacity of such foundations. In some cases, the feasibility of these tests is impractical because the associated initial cost is not guaranteed to outweigh the final savings. As a result, large scale load tests are sometimes ruled out from the design phase of projects. Furthermore, in the majority of load tests the magnitude of loads applied are specifically selected to not approach failure, so the shafts can be used in the future foundation system (i.e. production shafts). This practice of field testing restricts our knowledge of the true capacity of the drilled shaft at failure; hence the nominal resistance remains unknown.

Jan 1, 2018

By C. -T. Mutale, A. S. Tuling

Titanium can exist in three different oxidation states. Its oxides are numerous and in presence of iron and oxygen, iron-titanium oxide compounds can also form. Some of the oxides are non-stoichiometric, making the determination of the thermodynamic properties of titanium and its oxides in molten steel and in slag difficult. Therefore, for the assessment of titanium activity in molten steel using the electrochemical measurements of oxygen partial pressure, the identification of oxides in equilibrium with titanium is important. This paper reports on an investigation of solid titanium oxide inclusions, which have been identified by combining different methods of analysis on quenched samples. These samples were taken from a Fe-Ti-melt at 1600°C, quenched in cold water then mounted and polished for optical microscopy. The oxide inclusions were analysed using transmission electron microscopy (TEM) with energy dispersive spectroscopy (EDS). Both single crystal and polycrystalline diffraction patterns were used to identify the oxides by comparing the d spacings with those in the ICDD X-Ray Diffraction (XRD) database. XRD was used to analyse the oxide particles on the top of slow cooled samples. It was found in the TEM study that the similarity of the diffraction patterns of the various phases meant that unique identification was difficult to achieve in some of the diffraction patterns. However, TiO, Ti2O3, Ti3O5, Ti4O7were identified in quenched samples, while TiO2, FeO.TiO2and iron oxides were seen in slow cooled samples. It was also confirmed that the type of oxides is related to titanium content of the samples. Keywords: Titanium, Titanium Oxides, Iron, TEM, XRD, thermodynamic.

Jan 1, 2004

By C Chambers

"AustraliaÆs mining sector faces challenges to its competitiveness; operating costs are being adversely affected as a result of volatile commodity prices and growing international market pressures.Diesel fuel-generated power used in typical remote mining projects is generally reliable and quick-to-deploy; however it is ongoing expensive operating cost.Many mines and communities in remote locations source electricity from diesel generation, and often pay over $300/MWh in fuel and carbon only (i.e. excluding CAPEX). These costs are expected to rise over time and are vulnerable to price shock events or supply chain interruptions in international markets.Solar photovoltaic (PV) and other renewables can be integrated with existing diesel units to provide a highly reliable power supply. Such renewables now provide a cheaper source of electricity while maintaining the mining industryÆs stringent reliability requirements; some renewables are now cheaper than diesel power ù supplying electricity at approximately $226/MWh.Also, significant funding and concessional rate financing have recently become available to support the development of remote solar-diesel (or solar-wind-diesel) hybrid systems, including: up to $2.2 billion of as-yet uncommitted grants through the Australian Renewable Energy Agency (ARENA) and is now seeking mining industry partners, up to $10 billion of concessional financing for emerging renewable technologies through the Clean Energy Finance Corporation (CEFC) and this commences July 2013, ongoing revenue support through the Renewable Energy Target scheme, and other regional support programs administered by various governments.This paper explores: the business case for renewables - what applications and when to consider them, the potential operating cost savings if solar was integrated, the technical challenges and common pitfalls, and how to overcome them, and the upfront investment costs and whether the site is eligible for Government subsidy programs.CITATION:Chambers, C, 2013. Off-grid solar in the mining sector - Can renewable energy reduce your operating costs?, in Proceedings MetPlant 2013, pp 71-85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

By Jessie L. Bonner, W. Stephen Blomberg, Mark Leidig, Heather Hooper

Understanding the effects of the bench on ground motion can improve the design of cast blasts and achieve improved blast efficiency while remaining below vibration requirements. A new dataset recorded in September 2003 from a coal mine in Arizona has allowed us to examine the excitation of short-period Rayleigh-type surface waves from four simultaneously-detonated explosions in and below a topographic bench of a mine. The explosions were recorded on a network of over 150 seismic sensors, providing an extensive understanding of the ground motion radiation patterns from these explosions. We detonated two separate explosions (~3 tons and ~1.5 tons ANFO) in the deepest pit of the mine, thus the explosions were shot to solid rock. Within 25 meters of these two explosions, we detonated two additional explosions of similar explosive yields in a bench, thus these explosions were shot to the free face. Radiation patterns and spectral ratios from the explosions show increased amplitudes (by a factor of 1.5 to 2) at azimuths behind the bench relative to the amplitudes in front of the bench. We compared these findings to seismic observations from two ~1.5 million pound cast blasts at the same mine and found similar radiation patterns. Modeling of these blasts shows that the variations in ground motion are caused by the topographic bench as a result of 1) horizontal spalling of the rock falling into the pit and 2) non- linear scattering near the free- face. We also note that shooting to a buffer (previously blasted rock) causes the azimuthal variations to be significantly reduced.

Jan 1, 2005