Search Documents

By Min Chen, Cui-huan Huang, Zhen Tian, Jian-hong Dong

"The present work studied the production of Fe-Si-Mn alloy from adjusted converter slag by thermodynamic analysis. The results showed that solubility of SiO2 in the molten slag increased with increment of temperature, and it is about 80% at 1800 ?. With increment of SiO2 content, a(MnO) and a(CaO) decreased, and a(FeO) increased to the maximum when w(SiO2) is about 30%. As a result, the reduction of the slag was in the order of Fe?Mn?P before SiO2 reduction, the reduction order was Fe?P?Mn?Si when SiO2 content in the slag was from 46.4% to 54.2%, and changed to Fe?Si?P?Mn when SiO2 content exceeded 54.2%. The mass fraction of Si in the alloy phase increases with increasing of w(SiO2) in the slag, and the mass fraction of Si in the alloy reached to 62.2% at 1800 ?.IntroductionFerroalloy production is a high energy consumption and high pollution industry[1-2]. If ferroalloy production could be produced from molten slag by addition of carbon-reducing agent, the valuable metal and oxide in the slag can be recycled, most importantly, if the high-temperature resource carried by molten slag can be made full use in the field of ferroalloy production, the power consumption of ferroalloy production could be cut down greatly.Converter steel slag is a kind of byproduct in steelmaking processing increasing rapidly with the increment of crude steel, but the utilization ratio is low. Most heat recovery research is still in the experimental stage except the heat recovery of blast furnace slag by water quenching method, at present[3-4]. It is of great significance for enterprises to energy saving and emission reduction if the molten steel slag could be utilized directly. Not only the reuse methods of liquid steel slag material can be promoted, but also the use of heat carried in the slag could be achieved. The basicity of converter slag is high and the activity of SiO2 is low so the reduction of SiO2 in the slag is little. The compositions of slag and metal phases were calculated by Factsage program on different conditions to explore the reduction of converter slag for recovery of valuable metals and an efficient new way to use the high-temperature heat combining with the current reuse and research status of converter slag. Further, the improvement of components activity in slag and the increase of Si concentration in the metal were also dicussed."

Jan 1, 2012

By František Molnar, Zsolt Szentirmai, Juraj Schmiedl, Felix Sekula

"Hydrometallurgical nickel production in Sered Nickel Plant (Slovakia) that treated roasted Albanian ore left behind a considerable amount of the solid leaching residue. About 6 million tons of this fine-powder residue containing approximately 52 wt.% of iron in the form of oxides is to the present day stored in a stockpile. However, its iron content makes it a potentially interesting secondary raw material for iron production. This secondary raw material is not, unfortunately, suitable for direct treatment in iron and steelmaking processes.This paper presents results of the laboratory tests of pyrometallurgical method of processing of the leaching residue by its roasting and subsequent refining melting. The objective of the selective reducing agglomeration roasting was to reduce iron oxides and to simultaneously avoid reduction of chromium oxides and silica. Refining melting is carried out in an inert atmosphere. The products of melting are technically pure iron and slag.IntroductionThe leaching residue stockpiled on waste dump near already non-existing Nickel Plant Sered, Slovakia, is considered to be one of the most important environmental burdens in this country. The 40-years of an on-going effort focused on finding the methods for extracting metals and thus remove the waste dump have not been successful [1,4,5,6]. From the literature survey it is evident that past investigations have been following three main routes:1.Removal of chromium by mineral processing methods prior to its metallurgical treatment to achieve final chromium concentrations below 0.3 wt.%.2.Pelletization of solid leaching residue and its subsequent reduction in blast furnace and steelmaking plant and simultaneous removal of chromium.3.Pelletization of solid leaching residue followed by metallurgical processing of preliminary reduced semi-product in electric arc furnace (EAF) accompanied by partial reduction of chromium."

Jan 1, 2008

By Harrison Hodge

In the Bayer process for alumina production, between 2–35% Al2O3 is lost with bauxite residue due primarily to incomplete dissolution of aluminiumbearing minerals during caustic leaching or the precipitation of sodium alumino-silicate solids. The recovery of sodium and aluminium from the residue, and particularly from the contained sodium alumino-silicates, is becoming an increasingly critical issue from both an environmental and economic standpoint. Lime-soda residue sintering followed by selective leaching has been proposed as a method to recover sodium and alumina. The factors influencing the sintering mechanisms and kinetics, and the subsequent leaching have not been well described to date. In this study, the physical and chemical changes taking place during isothermal sintering of bauxite residue in air, particularly at short reaction times are investigated using scanning electron microscope (SEM) and X-ray diffraction (XRD). The impacts of these changes on the recovery of valuable materials are reported.

By Peter K. Liaw, Niann-i Yu, Wei Zhao

"For a plain-weave Nicalon ™ fiber fabric-reinforced silicon carbide (SiC) ceramic composite, little attentation has been paid to the effect of fabric stacking sequence on its mechanical behavior. In this paper, fiber-fabric stacking sequence effects on the elastic stress distributions, ceramic matrix-cracking stress, effective elastic moduli, and flexural strengths of laminated flexural test bars are quantified. A quantification model is established based on the combination of classical laminated plate theories and a fiber undulation model developed by Chou et al. A FORTRAN program is compiled to implement the modeling, which can be run in a SUN work station. The mechanical performance of a continuous fiber-reinforced ceramic-matrix composite (CFCC) with a [0/30/60] lay-up was analyzed and predicted. The variation in the fiber-fabric stacking sequence can vary the elastic stress distributions along the thickness direction of specimens, magnitude of ceramic matrix-cracking stress, effective elastic moduli of the laminate, and crack initiation sites as well as fracture modes. Moreover, all these factors contribute to scatter in flexural strengths of the CFCC.I. IntroductionWith enhanced fracture toughness and the ability of non-catastrophic (graceful) failure behavior, CFCCs are currently under evaluation for high-temperature structural applications in heat exchangers, combustors, hot-gas filters, boilers components, first walls and high-heat flux surfaces gas turbines, space vehicles and nuclear reactors.[1-8] Extensive applications of CFCCs by industry are still hampered by an insufficient understanding of the mechanical behavior, and sometimes, the lack of a well-developed and widely accepted design philosophy, in addition to the high-production costs."

Jan 1, 1998

By Qian Li, Haiyan Leng, Kuo-Chih Chou, Haoyuan Xiao, Zhigang Yu

Magnesium borohydride and Magnesium alanate were synthesized by mechanochemical metathesis reaction. The thermal decomposition behaviors of Mg(BH4)2-nMg(AlH4)2(n=0.5,1) systems were investigated as potential hydrogen storage materials. The results showed that the systems started to desorb H2 at 120 ℃ and desorbed 3.9 wt. and 4.9 wt.% H2 below 300 ℃ when n equals 0.5 and 1, respectively, while individual Mg(BH4)2 started to desorb H2 at 250 ℃ and desorbed only 0.82 wt.% H2. Because of the exist of the Mg(AlH4)2, the isothermal desorption kinetics of Mg(BH4)2 in the Mg(BH4)2-0.5Mg(AlH4)2 systems was 50% faster than that of pristine Mg(BH4)2. In addition, the re-hydrogenation rates also increased 49.4% and 37.9%.

Jan 1, 2015

By Ignacy A. Lipiec

The advantage of microorganisms used in bioleach systems to conventional chemical reaction systems is that these apply the available energy more precisely where it is needed, either directly onto the mineral of interest or by efficiently catalyzing the production of a reactant. The literature cover the range from empirical models used in describing macro heat balance in heaps to detailed studies relating the micro heat effects of bacteria adhesion energy to the surface of minerals. In this paper, the heat effects are reviewed in a general way describing bioleaching in two macro systems, heap leaching and slurry bioreactors. The micro scale heat effects is the reactions and conditions at the microorganism scale, including the mechanism of leaching and bacterial behavior.

Jan 1, 1998

By Jianhui Wu, Jing Zhan, Chuanfu Zhang, Zhijian Wang, Chu-ping Xia

"A novel technology about interactive roast of complex bismuth sulfide ore with low grade and Pyrolusite was put forward using the low-grade bismuth sulfide ore and pyrolusite as raw materials. The predominance diagram of Bi-Mn-S-O system was drawn by thermodynamic calculations. Stable coexistence area ofBizO3 and MnSO4 and its control condition was obtained. The interactive roast conditions including roasting temperature, roasting time, the ratio of n(MnO2)/n(S), ventilation rate and so on are investigated systematically. The results show that the sulfur-retained ratio reaches about 98%, in which formation rate of MnSO4 was 94.04%, most of the residual sulfur in the ore exist in the form of BhsO32(SO4)10 in the roasting products The optimum roasting conditions were as follows: roasting temperature of 650°C, roasting time of2h, 1.4 for n(MnO2)/n(S) and 140L/h for ventilation rate.IntroductionBismuth is a ""green"" rare metal with the characteristics of safe, nontoxic and low melting point[l].The use of bismuth and its oxides is extending from traditional fields such as pigment, fusible alloy, bismuth class of drugs and metallurgical additives to the high-tech fields such as semiconductor, high-temperature superconducting materials and nuclear power and so on. Bismuth is one of the precious advantageous resources in China which owns the most abundant bismuth resources in the world. Bismuth metallurgical process is divided into the pyrometallurgy and hydrometallurgy [2-4]. Hydrometallurgy for bismuth is mainly used for the processing oflow-grade complex bismuth ore, whose key steps are oxidative leaching process of the bismuth sulfide ore by strong oxidants(FeCb, Clz, HNO2 etc) in hydrochloric acid system. Therefore, the corrosion of strong oxidants, high demand for equipments and poor operating environment are its inherent disadvantages. Pyrometallurgy for bismuth is mainly used for the processing of high-grade bismuth raw materials or concentrate, which is the main method for bismuth metallurgy at present."

Jan 1, 2013

By Snehanshu Pal

"Concrete understanding of fluid dynamics properties inside basic oxygen furnace (LD converter) and hot-metal surface deformation due to impinging oxygen jet is important for optimization of reaction kinetics and maximization of productivity and refractory lining life. In this study various k-å turbulence models and volume of fluid (VOF) method have been used to model fluid flow and interaction of impinging oxygen jet with hot metal for an industrial scale top blown LD converter.RNG, standard and realizable k-å turbulence models are used to study velocity magnitude, stream function, turbulence intensity profiles. Turbulence kinetic energy, turbulence eddy dissipation, velocity magnitude and probable mixing time have been calculated in three locations inside the converter.The average rate of oxygen jet penetration, location of vortex formation, centre line and superficial velocity of impinging oxygen jet, probability of emulsifícation are studied by VOF method.These simulation studies provide better understanding of phenomena inside LD converterIntroductionComputational fluid dynamics (CFD) modeling in the field of basic oxygen steelmaking can improve substantially the understanding of existing processes where investigation of liquid steel flow measurement is hardly possible due to the rough ambient circumstances. In order to reasonably predict gas stirring operations and emulsifícation, mass, momentum, energy transfer and dynamic interaction among ions, atoms, molecules in the bath, detailed information on flow patterns, fluid velocities, and turbulent properties is essential. Concrete understanding of bath fluid dynamics inside basic oxygen furnace is also important for optimization of reaction kinetics inside the bath and maximization of LD converter lining life."

Jan 1, 2012

By Richard Elliott

Current methods for producing low-carbon manganese alloying materials for the steel industry are energy intensive and costly. To enable wider implementation of high Mn steel alloys, a novel solid-state Mn ore reduction strategy is therefore being investigated. This solid-state process, modelled on existing Direct Reduced Iron technology, employs a methane-containing atmosphere to reduce Mn ore pellets to a metal carbide. These pellets may then be smelted, yielding a Mn-rich master alloy. It is well established that CH4 is a suitable reductant for Mn ore powders; however, the reduction behaviour of industrially relevant Mn ore pellets by CH4 is poorly understood. The present work reports the results of an investigation undertaken to address this knowledge gap. The results of this study highlight the significantly different reduction behaviour exhibited by the Mn ore pellets relative to the ore powder under similar conditions and suggest that the diffusion of CH4 into the pellet interior is the limiting factor in achieving complete reduction.

By Christopher Solnordal

A mathematical model was developed to simulate the performance of the reaction shaft at BHP-Billiton?s Olympic Dam copper flash smelter. In order to have confidence in the predictions of the mathematical model, validation was performed by comparing and reconciling the predictions from the model with the results from a campaign of sampling and plant measurements. The model was based on the computational code CFX4.4 utilizing a combustion sub-model purpose-built by CSIRO. The combustion sub-model employed the concept of a composite particle which contained the three components of the solid charge: concentrate, flux and returned dust. Plant measurements were made and samples taken immediately below the burner and through a port halfway down the reaction shaft. Parameters measured included temperature, solid loading and SO2 concentration in the gas. Comparison of the measured and predicted values then showed that: predicted far field gas temperatures were within ±50C of measured values; predicted temperatures in the central plume were lower than measured, and, the predicted plume width was slightly smaller than measured. An optimum composite particle size of 19 m was identified for use in future modeling work at Olympic Dam.

Jan 1, 2006

By Jincheng Hu, Honggang Zhong, Qijie Zhai, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of cooling intensity on the solidification structure and ferrite phase content of a new duplex stainless steel (DSS) was investigated by using a thermal simulation setup for continuous casting. The results showed that the characteristics of the solidification structure were similar to their industrial scale manufactured slabs, including chill zone, colunmar zone and equiaxed zone. And austenite morphologies were mainly primary and secondary Widmanstatten sideplates as well as intragranular Widmanstatten plates. In addition, it revealed that the ferrite content increased with an increasing distance from the chill surface and decreased at colunmar to equiaxed transition (CET) position, then the value remained relatively stable at equiaxed zone. Furthermore, the ferrite content presented the same trend with the cooling intensity ranging from 100 mL/min to 2000 mL/min with the values just varying in a slight range.IntroductionThe duplex stainless steel (DSS) is the kind of steel that ferrite phase and austenite phase occupy about 50% respectively, or the content of the fewer phase has to be more than 30% [l]. The success of modem duplex stainless steels is to a large degree due to their higher strength than austenitic stainless steels, higher toughness than ferritic stainless steels, good weldability and high resistance to stress corrosion cracking as well [2,3]. The cost of stainless steel production continues to soar in recent years due to the increasingly higher price of Cr. In order to decrease the production cost, a new type of duplex stainless steel was developed by Bao steel [4]. This newly developed duplex stainless steel had low Cr content compared with 2205 DSS, and was expected to be applied into automobile industry. However, this type of steel was still in the initial stage of development, and the influence of continuous casting process on its solidification process and structure was still unclear, which needed to be studied further. Several works published in literature presented the effect of continuous casting conditions on duplex stainless steel (DSS) 2205, 2304 [5,6]. It was discussed that the cooling intensity in the chill-side had little efficient influence on the phase transformation. In this paper, the effect of cooling intensity on the solidification structure and ferrite volume fraction of this DSS at a given cooling rate was investigated."

Jan 1, 2014

By Wankun Wang, Shixing Wang, Jinhui Peng, Zebiao Zhang

"Germanium leaching from germanium dust and fume was carried out using sulphuric acid. Response surface methodology (RSM), based on a five level, four variable central composite design (CCD), was employed to obtain the best possible combination of liquid/solid ratio (Xi: 2-10), leaching time (X2: 1-5 h), sulphuric acid concentration (X3:3.15-15.75mol/L) and leaching temperature (X4:50-90 *C) for germanium leaching. The obtained experimental data were fit to a one-order polynomial equation using multiple regression analysis and also analyzed by analysis of variance (ANOVA). The 3-D response surface plot and the contour plot derived from the mathematical models were applied to determine the optimal conditions. The optimum extraction conditions were: liquid/solid ratio of 10, leaching time of 1 h, sulphuric acid concentration of 15.75 mol/L, and leaching temperature of 87.8 'C. Under these conditions, the germanium leaching extent was 65.14%, which is in close agreement with the value predicted by the model. The samples were characterized before and after leaching using X-ray diffraction (XRD).IntroductionResponse surface methodology (RSM) is one of the relevant multivariate techniques which can deal with multivariant experimental design strategy, statistical modeling and process optimization [1-15]. It is used to examine the relationship between one or more response variables and a set of quantitative experimental variables or factors. This method is often employed after the vital controllable factors are identified. It is also used to find the factor settings that optimize the response. Designs of this type are usually chosen when a curvature in the response surface is suspected [6], The process optimization of the sulphuric acid leaching of germanium from germanium dust and fume has not been reported in the literature. Hence the present work intends to assess the effects of variables such as liquid/solid ratio, leaching time, sulphuric acid concentration and leaching temperature and to identify the optimum conditions using RSM. The characteristics of sample before and after leaching are assessed using the advanced analytical instruments such as X-ray diffraction (XRD)."

Jan 1, 2012

By Moto Goto

PT Smelting, located in Gresik, East Java, is the first copper smelter and refinery in Indonesia. Since the first charging concentrate in December 1998, many equipment troubles have been systematically eliminated, and the present operation is smooth and has accomplished the design capacity of 200,000 tonnes per year of LME, grade-A copper cathode. This paper describes troubles and countermeasures, which were experienced until now.

Jan 1, 2002

By Frank Mucciardi, Hujun Zhao, Pietro Navarra

"A heat pipe is a device having a very high effective thermal conductivity in which two-phase flow and heat transfer takes place. Recent research at McGill University has led to a new type of heat pipe that contains a flow modifier. This improvement has enabled the device to operate at the high heat fluxes encountered in the metallurgical industry.This paper summarizes the progress made to describe the fluid flow in the evaporator section of a McGill heat pipe with the goal of understanding how the flow modifier configuration is linked to the film boiling and dry-out limitations. A separated flow model, an instability analysis, a lift-off model and an energy balance model are used to calculate the theoretical CHF with varying flow modifier configurations and operation conditions. A summary of the current work to relate the flow modifier to the dry-out limitation is also given.Determining how the flow modifier affects both the film boiling and dry-out limitation will give insight into improving the flow modifier design so as to extend the operational range of McGill heat pipes in terms of maximum heat flux and heat load capabilities.IntroductionThe McGill heat pipe is a specialized two-phase heat exchanger developed for several metallurgical applications where temperatures and heat fluxes are typically close to or beyond the maximum safe range of conventional cooling technology.Over the last few years, several breakthroughs have brought this device beyond the proof-of concept stage and a series of industrial trials have been performed with success. These trials include two oxygen injection applications for the ferrous and non-ferrous industry [l], and two light metals permanent-mould casting applications [2,3]. Current projects include a blast furnace copper taphole cooling application [4], a copper smelting application and a thermal analysis probe application."

Jan 1, 2004

"Recycling of solid wastes plays an important role in environmental protection. However, solid wastes are often contaminated with some undesired components so that many of these solid wastes are hardly economically recycled. Therefore, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes. There exist three general strategies of separation of undesired components from solid wastes: before-process separation, post-process separation and in-process separation. In this paper, different separation strategies are discussed in terms of energy requirement and availability, implementation complexity and additional need for environmental protection. It is concluded that of all separation strategies, in-process separation has the least energy requirement, the least implementation complexity and the minimum need for additional environmental protection.IntroductionIn industries, solid wastes almost come with every production process. Multi-million tons, if not billion tons, of solid wastes are being generated globally each year. These solid wastes are lowvalue materials in general, and often have very limited markets. As a matter of fact, many of these solid wastes have been stored on site or have been disposed of at landfills for many years, not only occupying lands, but also polluting environment. Therefore, effective and efficient recycling of solid wastes has been a very challengeable task and has played a very important role in environmental protection.One of the major barriers which hinder recycling of solid wastes is contamination of the solid wastes with some undesired components. These undesired components are components which are not wanted by production processes or applications where the solid wastes are consumed or recycled, since the undesired components often degrade qualities of the solid wastes, imposing negative effects on operations, facilities and product qualities of the production processes or applications. Sometimes, the undesired components may also pose severe environmental concerns. When undesired components are present in solid wastes at over-limit levels, the solid wastes tum to become destructive, useless and non-recyclable. Consequently, effective and efficient separation of undesired components from solid wastes becomes a crucial step for sustainable recycling of the solid wastes."

Jan 1, 2014

By Hongmin Zhu, Suning Liu, Kai Huang

"Recovery of silicon particles from the cutting slurry for the manufacturing of solar grade silicon is very important to recycle this kind of special resource. The challenge is to separate the silicon particles from the mixed abrasive particles which contain SiC. Various methods such as sedimentation, centrifugation, and flotation have been conducted, while in present work, a simple and effective novel method was proposed to study the separation of Si and coexisting SiC particles in the cutting slurry. The new process is based on the size difference between the two kinds of microparticles. And the membranes with the different pore sizes of 1µm, 2µm, 3µm and 5µm were used to test the pass ratio and separation efficiency of the suspension. Results shows that the effective separation of Si and SiC microparticles was obtained under the optimal conditions, and indicating great potential of practical enrichment of Si from the coexisting abrasive particles.IntroductionWith the development of the world economy, energy shortage and environment problem is becoming more and more seriously. Solar energy, which is regarded as one of the most important new energy in the word, has received much attention and interest from the scientists [1, 2]. More than 80% solar cells are manufactured by the high purity polysilicon as the raw material. The main process of producing silicon wafer is by multi-wire slicing. In this slice processing, large amount of slurry is produced. The slurry contains more than 30% wt silicon powder, silicon carbide powder as the abrasive, scraps of metal chips, as well as cutting abrasive suspension polyethylene glycol (PEG). The high-purified silicon powders are worth recycling and reusing as the materials for preparing solar-grade silicon though it is a big challenge [3].Most of the current studies were focusing on the recycling of the silicon carbide and PEG, while work on the recycling of the high-purified silicon is not so been focused since there is lacking of very effective separation and recovery technologies till up now. Nishijima utilized the method of superconducting magnetic to recycle the abrasive [4]. Wang applied a combinational process of chemical treatment, high-gravity centrifugation, high-temperature precipitation technique and directional solidification to enrich the silicon [5]. And other purification methods, such as centrifugation [6], froth flotation technologies [7], electrical filed separation [8] and phase-transfer process [9] have been employed. The disadvantages such as using poisonous media or complex equipments decrease the feasibility and efficiency of the above mentioned techniques."

Jan 1, 2014

By Xudong Liu, Feng Chen, Yufeng Guo, Wei Chen, Tao Jiang

Willemite is typically found in oxidized zinc ores and metallurgical secondary resources but without effective extraction method yet. Based on the ideas of zinc phase reconstruction in the willemite, the extraction of zinc from willemite by calcified-roasting using CaO as additive and ammonia-leaching process was studied in this paper. The influences of CaO dosage, roasting temperature, roasting time on the phase transformation and zinc leaching rate were studied, which were characterized by XRD. The results indicated that Zn2SiO4 was transformed into ZnO or Zn2CaSi2O7 .After roasted with 1.4 times of theoretical CaO dosage at l280 for 40 minutes, willemite was thoroughly transformed into ZnO. The zinc leaching rate of the roasted sample was 97.45% in NH4Cl-NH3 H2O leaching system, which increased by 91.40 % compared with zinc leaching rate of 6.05% when willemite was directly leached in NH4Cl-NH3 H2O system.

Jan 1, 2016

By Eltefat Ahmadi

Iron-free titanium oxycarbonitride (TiOxCyNz) is a promising feedstock for production of titanium tetrachloride (TiCl4) at low temperatures. In this study, the effects of leaching variables such as temperature, time, particle size of staring material and concentration of the leaching solutions were evaluated on iron removal from nitrided Malaysian ilmenite by Becher process. The nitrided ilmenite was prepared by isothermal reduction with graphite at 1200 °C for 3 h in H2-N2 atmosphere. The aerated leaching experiments were conducted at 50–90 °C with addition of 0.3–2.0 wt% of NH4Cl catalyst. The highest extent of iron removal (XFe) was obtained at about 96.2% for the sample leached at 90 °C for 7 h with 2.0 wt% NH4Cl. The iron concentrate and titanium oxycarbonitride product were characterized by ICP-OES, XRD, XRF and SEM-EDX analyses. The results indicated that the aeration leaching process was a successful route to prepare low-iron titanium oxycarbonitride.

By E. Gratz, U. Pal, A. Powell, S. Pati, J. Milshtein

"The solid oxide membrane (SOM) process has been used at 1150 'C to produce magnesium by direct electrolysis of its oxide. Magnesium oxide is dissolved in a molten CaF2-MgF2 ionic flux. An oxygen-ion-conducting yttria-stabilized zirconia (YSZ) SOM membrane separates the cathode and the flux from the anode. During electrolysis, magnesium ions are reduced at the cathode and Mg(g) bubbles out of the flux into a separate condenser. The flux has a small solubility for magnesium which imparts electronic conductivity to the flux. The electronic conductivity decreases current efficiency of the process and also degrades the YSZ membrane. This study investigates different methods for reducing the electronic conductivity of the flux due to magnesium solubility. One effective method shown here is inert gas flushing near the magnesium nucleation site. Potentiodynamic and potentiostatic experiments along with AC impedance spectroscopy are used to characterize the effectiveness of the approach.IntroductionMagnesium is the third most abundant metal in the earth's crust. Since magnesium is the lightest of all metals used for construction alloys, magnesium is the leading candidate to replace steel and aluminum in automobiles. Automobile manufacturers would like to increase magnesium content from 4-5kg per vehicle to 40-IOOkg per vehicle [I]. Using magnesium alloys instead of steel and aluminum can reduce automobile weight and improve fuel efficiency. However, in order for automobile manufactures to make this change, it is generally believed that new cost effective methods of magnesium production must emerge.One approach for magnesium production which has been shown to be effective on a laboratory scale is the direct electrolysis of magnesium oxide utilizing an oxygen-ion-conducting solid oxide membrane (SOM), this is known as the SOM process [2]. A recent study estimated that a commercial SOM plant could produce magnesium from magnesium oxide at a cost that is 40% less than current technologies [3]."

Jan 1, 2012

By Alejandro R. Alonso, Lizet Alvarado, Gretchen T. Lapidus

"Cobalt and lithium recovery from spent Li-ion secondary batteries has been increasingly studied in recent years due to the high value of both metals and the low proven reserves for lithium. The standard method employed until now has been the deactivation and crushing of the batteries, followed by leaching of the L1C0O2 spinel from the battery cathode using acid solutions, such as 1.5 to 2.0 M HC1 or H2SO4, in a temperature range from 120°C to 250°C. Once leached, the cobalt is separated by electrodeposition and the lithium by precipitation, using large amounts of carbonate to bring the solution to alkaline pH values. In the present work, citric-thiosulfate solutions are used for the spinel leach at room temperature, favoring a reductive environment at room temperature, which stabilizes the cobalt(II) as cobalt citrate and lithium(I) at pH 5, and recovers approximately 99% of both metals.IntroductionThe Li-ion batteries industry has become an important economic sector in recent years. This type of battery is the most promising system for energy storage, because of its high efficiency in charge-discharge cycles, and its adaptability to many configurations. The demand will probably increase because of the need for mobile energy sources in many types of devices ranging from cell phones, tablets, and laptops to medical, navigation and sophisticated communication equipment and even in automobiles.One major problem related to the use of these batteries is the method employed for recycling the components, mostly cobalt and lithium. Currently, there are two processes employed on an industrial scale: the Sony/Sumimoto process, used since 1990 [1] and the Toxco Process [2]. In the first case, incineration is used to open the batteries and at same time volatilize the organic solvents. After that, the metals (copper, iron and aluminum) are physically separated. The cobalt and lithium are recovered as oxides and then thermally treated in order to recycle them for new batteries manufacture."

Jan 1, 2012