Search Documents

By I. Iwasaki

The presence of calcium ion in iron ore pulps causes heterocoagulation of montmrillonite on hematite leading to indiscriminate dispersion. Two methods were investigated to control the adverse effect of montmorillonite: chemical method using such complexing agents as EDTA and sodium tripolyphosphate, and mechanical method involving ultrasonic treatment. Their roles in controlling the adverse effect were investigated by zeta potential measurements, starch adsorption tests, and flocculation and selective flocculation tests.

Jan 1, 1986

By David J. Boron

The United States has the largest total (364 billion metric tons) and recoverable (182 billion metric tons) coal reserves in the world.1 However, progressive coal utilization in this country has been hampered by environmental constraints, such as restrictions on sulfur dioxide, nitrogen oxides, and particulate emissions. New technologies are being pursued both to appease these environmental concerns and improve economic performance and process efficiency. These technologies, however, have not reached the level of effectiveness required for optimum operation. If more stringent emission standards are imposed, it is likely that the coal industry, and the industrial and utility sectors will look increasingly toward the successful development of new and advanced coal cleaning technologies in order to continue and promote the use of coal in this country. The EPA New Source Performance Standards In 1979, the Environmental Protection Agency in response to the amendments to the Clean Air Act of 1977 issued new source performance standards (NSPS) for utility and industrial boilers. The NSPS set emission standards for sulfur dioxide, nitrogen oxides, and particulates affecting boilers of 250 MM Btu per hour heat input or 'greater that started construction after September 1978. Plants starting construction or in operation before September 1978 remained subject to the provisions of the regulations promulgated in 1971, i.e., SO2 emissions of 1.2 15/MM Btu. The NSPS for SO2 emissions provides a sliding scale for SO2 reduction depending on the sulfur content of the run-of-mine coal, with an upper limit of 1.2 lb of SO2 per million Btu and a minimum emission level based on 70% SO2 removal. Table 1 summarizes the EPA NSPS for SO2 emission standards.

Jan 1, 1983

By B. Cavender

Investments in new technology are often intended to improve the production or cost performance of existing operations. The economics used to justify these projects can be flawed, however, if they do not adequately consider the potential benefits of the alterative: the fully optimized use of the facility's present equipment and personnel. While new technology can be effective, dramatic improvements in production performance can also be achieved through the rigorous application of standard industrial engineering and operations management practices. An intermediate approach may also be effective: many basic improvements In the mine or plant necessary to support new technology will be equally effective when implemented for the facility's present operators. Firms who optimize their present operations are able to save the capital and avoid the risk associated with new technology. These firms will also be able to capitalize more quickly on new technology when it is implemented.

Jan 1, 1999

By Bryan Ulrich

Knight Piésold?s annual roundtable discussion was held at the Red Lion Hotel and Casino in Elko, NV on March 14. This year the title was, ?Roundtable discussion on material co-disposal/ co-placement in the mining industry.? This topic was chosen because of the benefits that the mining industry could realize through the advancement of improved methods of storing tailings and mine waste and from reducing short-and long-term environmental hazards while reducing the footprint of these facilities and making strides toward attaining a walk-away solution. Knight Piésold had a local representative, Bryan Ulrich, as well as representatives from its Denver, CO office, including Tom Kerr, president of Knight Piésold?s U.S. practice, and Jeff Coffin, Ph.D., geotechnical engineer, to help facilitate the discussion. The event played host to about two dozen attendees from several western states. Attendees included personnel from more than 10 mining properties, various corporate offices and academia. The purpose of the roundtable was to exchange ideas and information pertaining to broad topics revolving around the subject of co-disposal/co-placement in the mining industry. Compared with traditional conferences and symposia, the roundtable forum tends to provide a less inhibited format for discussion. In the roundtable format, lively discussions and applicable tangential departures are encouraged. This was the seventh in the series of the Elko Roundtable events. Previous roundtables pertained to: ? Heap leach pad design, construction and operation. ? Design, construction and operation of tailings storage facilities. ? Site-wide water considerations. ? Mine closure and cover design. ? Strides toward sustainability in mining. ? High-density tailings, paste and filtered tailings. Acid rock drainage for engineers and environmental scientists.

Nov 1, 2013

By Ross W. Whipple

Applying geophysical techniques in potential geothermal areas has received: little attention in the United States, though it is widely used and accepted in New Zealand and Italy. In those countries it has been demonstrated that geophysical surveys can be useful in locating new geothermal areas and in directing test drilling programs. Geophysical studies in a thermal region can provide structural information and, if conditions are right directly; locate subsurface hot waters. They can give indications of sub-alluvial rock types and of the thickness of alluvial cover. In certain cases they can be used to estimate the power potential of a hydrothermal system.

Jan 1, 1963

By Chee Theng

"What would you do if you are an industry leader and disruptive technology threatens to overturn your business model? Although bearings and seals are in little danger of being displaced in the near future, one company is taking no chances in an age of digital disruption.“For SKF, digital transformation and the Industrial Internet of Things (IIoT) make this time right now arguably the most exciting time in our 100-plus years of history,” John Schmidt, president of SKF USA Inc., said during the SKF Technical Press Day in Philadelphia, PA.The company is not merely integrating digital technologies into its products and services but is taking a forward-looking, strategic approach. “To be successful, legacy companies have to undertake a process called digital transformation. It’s not just an IT initiative but is really about upgrading the strategic thinking,” explained Michael D’Argenio, vice president of digital transformation and customer experience at SKF Americas.Learning from those who went beforeD’Argenio cited the examples of two companies that saw entirely different outcomes in the face of digital disruption. The well-known case is that of Kodak, one of the storied brands in history, whose business was disrupted by the advent of digital photography. Although it invented digital photography, Kodak decided to box it up and put it on the shelf because it was scared of disrupting its business in photographic fim. Instead, it was disastrously disrupted from the outside.Less well known is the case of Encyclopedia Brittanica Inc., publisher of the longest-running English-language, general-knowledge encyclopedia in the world. Sales peaked at 120,000 sets in 1990, plunging to 8,000 sets in 2012. In 20 short years, it saw not one but two massive digital disruptions. The first was in 1993, when Microsoft published the first digital interactive encyclopedia on a CD-ROM, called Encarta, priced at just $99. The second was in 2001, when a communitycurated, free website called Wikipedia launched. Taking the opposite approach from Kodak, Encyclopedia Brittanica looked at its industry, its company and its customers through the lens of the new technologies, made a prediction about the future and, based on that prediction, took a bold move. Having identified its core value proposition as the delivery of reliable, high-value, verifiable knowledge, Encyclopedia Brittanica replanned, restructured and rebuilt its company from the ground up to deliver that same value proposition, only in a different way. It stopped producing the only product that it had known for 244 years and began producing digital products that it sold to educational institutions.“There is a lot to learn from the Encyclopedia Brittanica case,” said D’Argenio. “The company embraced its market change, it embraced its customer change, and it rethought what it needed to do to be successful. Because it owned that disruption internally, it was never disrupted from the outside. It continues to operate today and is as profitable as it has ever been.”"

Aug 1, 2019

By S. Tafazoli, N. Himmelman, D. Chan, E. Chow

"While Wearable Technology has been garnering attention in the consumer market, enterprise and industry have just begun exploring its potential applications. Since February 2014, Motion Metrics International has been working in collaboration with Vandrico Solutions Inc. to apply Wearable Technology to improve productivity and safety in the mining industry. This paper discusses the value proposition of using Wearable Technology to deliver critical notifications in mining. The advantages and disadvantages of various form factors are explored. The challenges, both specific to mining and in general to Wearable Technology, are defined. Finally, the concept of MetricsGear™, the first Wearable Technology platform developed for mining by Motion Metrics International in collaboration with Vandrico Solutions Inc., is described. MetricsGear™ is designed to notify the user with minimal distraction to keep the user focused on their primary task, and aware of mission-critical events. This focus and awareness allows the user to work more efficiently and safely. INTRODUCTION The mining process consists of a series of intricate stages, where certain events or conditions in one stage can have a huge impact on other stages. The notification of these critical events or conditions is vital for ensuring the overall efficiency of the mining process. Critical notifications can be classified as two types: time-critical events and contextual information. Time-critical events are situations where a timely response from a responder can have a significant impact on seizing an opportunity or mitigating cost. Some Human-Computer Interaction (HCI) experts classify notification types based on the Interruption, Reaction, and Comprehension (IRC) framework. Time-critical events are classified to have high interruption, high reaction, and low comprehension due to their urgency. The responder should have just enough information to identify the crisis and react as soon as possible (Chow, E. 2014). For example, when a tooth is lost during shovel operation, it is necessary to recover the missing tooth before it jams the primary crusher. The consequence of missing this critical time period is a jammed crusher that can cause the mine to be out of production until the jammed tooth is extracted (Baumann, M. 2013). In this case, the responder only needs to see an image to confirm if the tooth is missing, and information to identify which equipment and when the tooth went missing (see Figure 1). Contextual information is relevant information that is valuable for the receiver to be aware of as it can present an opportunity to improve efficiency or save cost. According to the IRC framework, contextual information is classified as low interruption, low reaction, and high comprehension. They are not as urgent as time-critical events, but provides more detailed and informative information to assist the receiver. For example, when a shovel’s worn tooth is predicted to require replacement soon, a notification to a GET technician can help him or her schedule a pre-emptive replacement of the tooth in an already planned maintenance to prevent having to reactively schedule another one when the tooth is critically worn. This helps reduce the amount of equipment downtime to maximize production (Baumann, M. 2013). In this case, the receiver will look at the information when he has a moment to spare to get a quick forecast, and make use of this information as needed (see Figure 2)."

Jan 1, 2015

By Juan Andres Jarufe, Carlos Cifuentes

Numerical modelling has been extensively used to estimate plastic displacement in faults and rock mass surrounding mine excavations. Particularly, for fault slip seismicity, modelled plastic displacement is usually utilized to estimate seismic potential, however these methods assume that all the displacement caused during an specific simulated excavation step, is released as a single event at each step. This representation corresponds to a conservative estimation since rock mass displacement does not occur as one single event but as an exponential distribution of many small displacements and a few large ones. When displacement is expressed as seismic magnitude, this exponential distribution is addressed as the Gutenberg Richter (GR) relationship. This paper present a method to decompose the results from numerical models into a distribution of seismic events The reconstruction of the GR relationship from modelling displacement permits not only a more realistic approximation of the expected maximum magnitudes but also provides a tool to develop a probabilistic estimation of the maximum possible magnitudes.

Apr 26, 2022

By M. S. Moats, A. Luyima, W. Cui

"Organic smoothing additives are used to produce dense, thick, high-quality cathodes in copper electrowinning. Glue had been used traditionally and is still used in operations that do not employ solvent extraction to produce the electrowinning electrolyte. With the advent of solvent extraction–electrowinning, guar started to be used and remained in use for many years as it does not affect the phase disengagement in solvent extraction. Recently, however, guar has been replaced by less-expensive saccharide- and polyacrylamide-based additives. This paper is the first of a series of four papers that examine saccharides and polyacrylamides as new additives for copper electrowinning. A review of previous research related to copper electrowinning additives is presented here, along with a selected review of additives in other copper electrodeposition systems.IntroductionThe recovery of copper from solution by electrowinning was first practiced in the early 1900s, but it was the combination of solvent extraction with electrowinning (SX-EW) in March 1968 at the Ranchers Bluebird Mine (Kordosky, 1992) that changed the landscape for the electrowinning process. Most copper electrowinning capacity is now associated with solvent extraction, though some copper is still won directly from leach solutions (Robinson et al., 2013). The ability to produce high-purity copper cathodes from SX-EW has taken the continued improvement of SX-EW technology over the past more than 40 years.One of the technologies that has seen improvement is that of the organic smoothing agents used during the electrodeposition of copper in the tankhouse. These organic additives are added to the acidic copper sulfate electrolyte during electrowinning to improve the smoothness, brightness and density of the copper cathodes. The organic additives that are presently in use are different from those used in 1999 (Jenkins et al., 1999). Over the past decade, many tankhouses have replaced the use of guar-based organic additives with those derived from other saccharides. Until now, there has been no comprehensive publication in the open literature on the behavior of these additives during copper electrowinning."

Jan 1, 2016

By William A. Wallace

Common mineral resources (sand, gravel, crushed stone, etc.), which are so necessary for the construction of metropolitan areas, are rapidly being depleted or otherwise rendered unavailable in the very areas that need them most. However, the problem of planning for these resources involves a number of independent and dependent variables that must first be defined and related. Finally, a dollar value must be assigned where possible. Complex interrelationships between the variables and their dependence on outside factors has made mathematical "solution" of the problem of planning for non-renewable mineral resources difficult at the present time. Therefore, the use of computer simulation is suggested as a means by which this complex problem can be investigated. The purpose of this paper is to report on a continuing research program whose objectives are: (1) to delineate the factors involved in planning for the utilization of common mineral resources in urban-suburban environs; (2) to construct a planning model for these materials amenable to computer analysis, (3) evaluate the model by using test cases, and (4) perform a sensitivity analysis to determine the initial parameters in future planning for these materials.

Jan 1, 1968

By Ning Wang, Tengfei Guo, Wanyan Li, Hanjie Wen, Hannian Gu, Zehai Li

Red mud has been reported as a potential resource for lithium. To investigate the leaching behavior of lithium, a lithium-rich red mud was neutralized with hydrochloric or oxalic acid and then leached with acetic acid. When red mud was neutralized using dilute hydrochloric acid, about 58 to 60 percent of lithium was leached with 25 percent acetic acid at 95 °C for 60 min, while more than 95 percent of sodium and 85 percent of calcium were dissolved in the leachate solution. When oxalic acid was used to neutralize red mud prior to acetic acid leaching, lower lithium leaching efficiencies of about 42 to 47 percent were observed. Nevertheless, these leaching efficiencies of lithium were close to that of calcium and much higher than those of sodium under the same conditions. In this study, 25 percent (v/v) of acetic acid at 85 °C for 60 min was demonstrated to be the optimum conditions for lithium extraction from oxalic acid-neutralized red mud using acetic acid. The results are useful and of interest for lithium recovery and purification from red mud.

By E. C. Winegartner

In producing and selling coal, the coal company is faced with many different parameters by which the quality of its product is evaluated. One type, which we choose to call the economic parameters, includes moisture, ash, sulfur, and Btu's. These are reasonably well understood by both the coal supplier and the customer, and the dollar values can be placed on them. This is the group of parameters of primary interest to most purchasing agents buying coal. A second group of parameters governs how the coal will behave in the boiler itself and is of primary concern to the engineers designing the boiler and to the men who must operate and maintain it. Since we have not yet learned to put dollar values on these parameters, they generally show up in coal contracts simply as cutoff points, the purchaser simply saying that he will not accept coal outside of certain limits.

Jan 1, 1975

By J. Wyn Prior

The seismic refraction technique is probably the most popular geophysical method of bedrock profiling in geotechnical site investigations but is somewhat restricted by the inherent assumptions in the method. This paper describes how Hales' method of profile interpretation is modified to overcome the assumptions of increasing velocity and layer thickness with depth when only first arrival data is available. A further expansion of Hales method enables presentation of refraction data in a form whereby bedrock features, such as changes in velocity, relief and dip in particular, are more readily recognized. Characteristic curves of the more common bedrock features are presented as an aid to bedrock feature recognition.

Jan 1, 1976

By William J. Robinson

What is the cummulative rate of recovery of copper from a sulfide leach dump? This is one of the most frequently asked questions today. We, in the industry, ask it of each other when we meet; however, the technical answers may vary from "I don't know" to 'quite good" from people within the same company. Management also poses this question because it plays a vital role in our planning for future production. The answer is difficult because of the many variables between different operations such as physical construction of the dump, topography of the original site, characteristics of dump material, mineralization, water application, etc. Each has a bearing on the rate of recovery. OPERATIONAL DATA Our method of water distribution is unique in that each dump is drilled to allow physical injection of water into the dump. The in¬jection holes are drilled vertically, on 251 centers, from the surface of the dump. Normally, the holes are drilled 40' deep and cased with 4" PVC perforated pipe.. The pipe is perforated at one-foot intervals with four V diameter holes at 901 spacing on the pipe circumference. We formerly alternated shallow holes (20'-40') with deep holes (80'-l80') in an effort to cover the entire dump and hasten oxidation. The shallow hole depth varied according to the compaction thickness. The deep hole depth varied according to the height of the dump and the original ground profile, We prefer to have the deep holes end 20'-30' above the original ground level. This generally allows us to penetrate the coarse material at the bottom of the dump. We had to discontinue the deep holes_ in order to cover more dump area in a shorter period of time to meet increased production requirements.

Jan 1, 1972

By Sandip K. Mukherjee

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper reviews developments in water spray dust control technology and recommends guidelines for water spray systems to control dust in under- ground coal and non-coal mining operations. These guidelines suggest type, number, location and orientation of nozzles, desirable operating water pressure, and associated filtration system.

Jan 1, 1983

By H. M. Ray

The discovery of the New Lead Belt in the mid-'50s began a search for mill design criteria that is continuously updated. The opportunity to design, construct, and operate four new mills in the span of 20 years provided fertile areas for new concepts. The central theme for design parameters encompassed simplicity, functional, and economic consideration. Ore characteristics for each plant remained relatively constant, providing stable criteria for grinding circuits. Bond index nominally 10-12. Flotation circuit parameters were based upon power application with 10-20% excess capacity built-in to protect recovery. Newer equipment exhibits greater power application efficiency lowering horsepower requirements per ton. Instrumentation was installed to stabilize circuits, protect equipment, and improve products. With ever increasing requirements of higher quality products, environmental considerations, and operating cost pressures, the upgrading of operating procedures is in a constant state of flux. Installation of more efficient equipment, chemical processing, or any other technique would be considered as feasible. Current practice is for St. Joe to design and engineer in-house its own plant design. The exception being detailing of structural steel. It is felt that familiarity with past design criteria serves as a valuable foundation to incorporate changes. Also, direct contact with operator provides specific data, and feedback for constructive criticism that is utilized for defining and correcting problems. The results are in reality an operator's plant with the benefit of advancing technology that meets the demands for improved products without sacrificing the economies of throughput or recovery.

Jan 1, 1977

By D. Malhotra

Most primary-molybdenite producers use a selective-flotation process in which molybdenite is floated from the ore while other sulfide and non-sulfide gangue minerals are depressed in the same step (Figure 1). The process was developed at the Climax mill. Reagents used in the rougher-flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother) and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born, et al, (1976) and Malhotra, et al, (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50 percent of the total molybdenite-flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors which would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate non-oil based collectors and collector systems that are less expensive than vapor oil.

Jan 1, 1985

By William Gleason

With more than 20 major mines extracting copper, gold, coal, molybdenum and lime, Arizona is recognized as one of the better mining jurisdictions, not just in the United States, but in the world. However, that is not to say the road to production is always paved with gold, or in many cases, copper. Earning the license to mine in Arizona is a complex process with years of paperwork and permitting before the first tons of ore are ever processed. Now, get the federal government involved and the process becomes even more complex, and the path to production can become even longer.

Jan 1, 2013

Zirconium chloride is of great commercial importance as starting materials for production of ZrO2, Zirconium metal and other Zirconium compounds from its main resources (Zircon Sands). The present study concerns with preparation of pure ZrO2 from Zircon by direct chlorination technique. Different parameters affecting the chlorination process are studied viz. carbon, chlorine flow rate temperature and time. The chlorination extent is determined from the loss in weight and chemical analysis of reaction products. The maximum chlorination extent -92% are achieved at 1100°C for 30 min. Zirconium oxide is produced from the collected zirconium tetrachloride either by calcination at 900°C or by hydrolysis in water in presence of RCI with a purity = 99%. Evaluations of the products of the process are investigated microscopically and by X-ray diffraction. The apparent activation energy of the chlorination of Zircon is determined to equal 36 kJ/mole.

Jan 1, 1997

By Justin Jensen, Luis Moya, Jose Carlos Durazo, William Szolga, Tyler McCallum, Tim Doubleday

Sulfuric acid mist is an undesired by-product of the copper electrowinning process, caused by oxygen evolution at the anode which entrains droplets of the acidic copper electrolyte solution. As the oxygen moves to the surface of the cell, these droplets become aerosolized resulting in acid mist. The addition of chemical anti-misting agents to the copper electrolyte is a common mitigation technique. This paper details Syensqo’s laboratory development of a new environmentally friendly acid mist suppressant, ACORGA® EW98. The product exhibits excellent acid mist suppression and it is fully compatible with the adjacent solvent extraction process. Lab and pilot test results are reviewed ahead of future planned industrial trial testing.

Feb 1, 2025