Search Documents

By G. W. Cutting

It is well known in both the research field and in commercial flotation processes that the grades and recoveries obtained from flotation plants are heavily influenced by the structure and height of the froths produced in the flotation cells. The development of steady-state mathematical models of flotation processes based upon practical and readily obtained parameters have demanded detailed information about the structure of flotation froths. The important parameters are the distribution of floating values, gangue and water in the froth with respect to froth height, cell pulp density, cell air flow rates and flotation inducing additives. Little work has been conducted in this field although considerable attention has been paid to bubble loading and other factors close to the cell froth/pulp interface. Laboratory batch tests are prefaced for the derivation of the above mentioned parameters for both practical and economic reasons. The standard laboratory flotation tests using a batch cell produces a froth of low height (1 to 3 cms generally) together with a varying cell pulp density as the test progresses due to the addition of top up water and the removal of froth from the cell. This form of test can be considered only as giving information about froth conditions close to the cell froth/pulp interface under conditions of widely varying cell pulp densities. In commercial processes the froth heights are much larger (frequently greater than 10 cms); therefore the laboratory batch test, although useful in many ways, does not directly yield parameters relating the state of the froth flowing over the cell lip to process operating conditions. To investigate flotation conditions, where more realistic froth heights are developed, an equilibrium type of batch cell has been developed at Warren Spring 1 Laboratory . In this a tank with high walls is used to contain the pulp and whole froth and, after a short period of operation, an equilibrium between froth

Jan 1, 1975

By Peter N. Yanker

The two types of dryers used in the drying of copper concentrates are the rotary dryer and the spray dryer. The rotary dryer has until recent history been the traditional drying method used, Although spray dryers have been used in the chemical field for many years it is only recently that they have been accepted for drying of copper concentrates. The comparison made here will apply in a narrower sense to the drying of copper concentrates as fed into the reverbatory furnaces of the Smelter. To compare a rotary dryer and a spray dryer, which are two totally different methods and pieces of equipment, it is best to view them as systems each made up of certain elements

Jan 1, 1976

By C. D. Taylor, A. L. Mazzella, A. L. Martikainen

In fluctuating airflow, continuous air velocity recording is the most reliable method of air velocity measurement. It allows for fast recognition of changes and the calculation of long-term averages. Also, it enables the mine operator to identify when the airflow has decreased to a point requiring action. Using ultrasonic anemometers provides an accurate option for continuous air velocity monitoring. This paper provides information about the effect of common obstructions in underground mining on air velocity readings. Stationary and moving obstructions are used to represent workers and equipment that would cause discrepancies in measured airflow. Also, it is important to know how large of a sample size is required to ensure reasonable accuracy of results. Statistical analysis is used to evaluate the required sample size. The sampling procedure is further studied by comparing two different sample rates. The results show that obstructions provide noticeable differences in air velocity measurements. Also, movement of obstructions can be recognized from changes in results. Surprisingly small sample sizes provide reliable air velocity information. Standard sample rates are found to be suitable for the underground environment.

Jan 1, 2011

By Andrea Brickey, RICHARD AMOAKO, Akshay Chowdu

Production forecasts derived from the medium-term schedule represent the best path forward for underground mining operations to achieve corporate and operational goals. Unforeseen circumstances, such as equipment breakdown, can cause significant deviations from established production forecasts in the short term. Such situations require timely mitigation of the effects of the deviations in order to stay as close as possible to the medium-term plan. This paper presents a deterministic mathematical formulation for short-term scheduling that addresses this challenge. The formulation is able to make up for deficits resulting from operational disruptions by minimizing deviations from medium-term production goals and medium-term activity start dates. We demonstrate this in a case study by simulating disruptions involving reduction in ore extraction capacity and development advance rate. Aside from the rescheduling capability, this formulation can help mine planners conduct analysis on the impact of various disruptions on the schedule. The formulation can help identify those conditions or disruptions that are more detrimental to the achievement of forecast targets, or otherwise. The formulation also affords mine planners the flexibility to prioritize one production goal over the other, depending on operational conditions at the mine. In the future, we seek to incorporate in the formulation respirable dust, diesel particulate matter and ventilation constraints in order to create more realistic schedules, and enhance miners’ health and safety.

Jan 1, 2024

By Richard C. Holmquist

Some of you may be old enough to remember -- as I do -- the early days of World War II. A highly prepared, well-equipped Japanese striking force had moved like lightning across the South Pacific islands and Southeastern Asia. As the invasion force pushed its way down the Malaysian Peninsula, Singapore stood serene and beautiful, protected by its natural moat of water, busy as ever with its commercial pursuits. One can see its captains of trade and industry now, sitting com¬fortably on the veranda of the "Singapore Country Club", sipping scotch between cricket games, convinced that the weary, logistically extended Japanese force couldn't possibly cross over to their island which had been so secure for a hundred' years or more. No need to remind you what happened. The brave men in their ships at sea and in the gun emplacements ashore were hopelessly out-gunned and out-maneuvered.

Jan 1, 1979

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1991

By R. Venugopal, V. K. Saxena, A. K. Mukherjee

"Coal, iron and manganese ore samples were exposed to different ultrasonic intensities of 250, 300 and 350 W/L for five minutes and to an ultrosonic intensity of 270 W/L for different time durations of 3, 5 and 7 minutes. The ultrasonically treated samples showed reductions in D80 particle diameters of 6 percent for the coal samples, 5.95 percent for the iron ore samples and 35.63 percent for the manganese ore samples during grinding. The ultrasonic treatment was also observed to assist in reducing ash content in the coal product by 8 percent and to reduce manganese losses in rejects by about 5 percent. Ultrasonic treatment was concluded to be capable of assisting in the comminution of friable ores more prominently than the hard and porous materials.IntroductionComminution is an important unit operation in the mineral-processing, cement-making, powergeneration and pharmaceutical industries. But most of the milling technologies are considered to be energy inefficient, with less energy consumed in real size reduction and most of the energy consumed in the machine. This is more critical for the mineralprocessing industry because of the growing need to exploit lower-grade ore bodies and process rejects (Blazy et al., 1994; U.S. Department of Energy, 2005). Low-grade ores require crushing and grinding to liberate the valuable minerals, which are further separated from gangues by various beneficiation methods such as gravity separation, flotation and leaching. Various studies have been carried out to minimize energy consumption during milling by developing pretreatment methods that can initiate new fractures or improve the fracture density in materials before comminution. These studies were mainly focused on chemical additives; thermal, ultrasonic and microwave treatments; and electric disintegration (Klimpel and Austin, 1982; Norgate and Weller, 1994; Bearman, Briggs and Kojovic, 1997; Gaete-Garreton, Vargas-Hermandez and Velasquez-Lambert, 2000; Kumar et al., 2010; Wang, Shi and Manlapig., 2011, Singh et al., 2012).The fragmentation effect of ultrasonic fields in solids has been investigated since the 1950s, and Gärtner was probably the first researcher who attempted it (Gaete-Garreton, Vargas- Hermandez and Velasquez-Lambert, 2000). Sound waves can propagate in solids in the form of longitudinal waves, shear waves and surface waves, and in thin materials as plate waves.In surfaces, fractures and interfaces, various types of elliptical or complex vibrations of the particles make other waves possible. During ultrasonic-vibration treatment, cavitation bubbles nucleate, grow and collapse, generating microjets, whose impacts on the particles initiate microcracks. The ultrasonic waves can enhance the nucleation, growth and coalescence of flaws, caused by tensile or shear stress. The mechanisms operating in the materials and inducing these stresses have been identified as spall and compression-induced tensile microcracks, nucleating at preexisting flaws. These mechanisms are driven by the shock wave and cavitation effects in the surrounding fluid (Chen, Huang and Shih, 2003)"

Jan 1, 2016

By H. Lyn Bourne

This is the 12th year for this column and the 11th in which the royalty data have been tabulated. This year adds 20 to 30 new entries. There are, however, some deficiencies that the readership hopefully will fill. The most common mineral commodity is construction aggregates - either sand and gravel or crushed stone. There are several states where no royalty information was available for either commodity. Readers can help share information about these missing states, so next year there will be fewer states without information. Severn Brown again sent helpful information from the Prospectors and Developers Association of Canada (PDAC). The summer 1992 issue of PDAC Digest recommended"... the most useful technical paper ever published for economic geologists...." "Net smelter return models and their use in the exploration, evaluation and exploitation of polymetallic deposits" was written by R. Goldie and P. Tredger (Geoscience Canada, Vol. 18, No. 4, pp. 159-171). Last year's column described leasing practices in Russia. Some new information has been gathered since then. Kirill Kavun is the managing director of the International Geoeconomic Center in Moscow. He sent two publications from 1992-"Regulation on the procedure of licensing the use of the subsurface," and "Law of the Russian federation on the subsurface." Both are supplements to the magazine Mineral Re¬sources of Russia, Economics and Management.

Jan 1, 1993

By Theodore H. Budd, Austin M. Cooney

The North Shore 9 Collector System comprised an integral part of the Milwaukee Metropolitan Sewer District's Water Pollution Abatement Program. The project required the construction of 1,490 m of tunnel, ranging from 1.5 m to 4.6 m in diameter along three separate alignments beneath arterial streets traversing Milwaukee's central business and cultural districts. This paper details the various aspects of the tunnel drives which were accomplished using two Lovat EPB type TBMs in conjunction with pipe-jacking procedures. Shaft configurations developed for the project, including ancillary subsidence mitigation components and portal pressurization facilities are discussed. Anomalies in observed soil behavior at variance with the parameters delineated in the project's geotechnical report are addressed.

Jan 1, 1993

By R. D. Stewart

Abstract. Induced fluorescent sorting is a means of beneficiating an ore by selective labeling with a reagent combination which fluoresces when activated by ultraviolet light The reagent combination normally consists of a surface active compound and a fluorescent dye. The surfactant adheres selectively to a specific surface and carries the dye with it. Upon activation with ultraviolet light, the labeled pieces, in the size range 1.27 cm to 20 cm (0.5 to 8 in.), are detected during free fall by photosensitive cells and ejected by water jets. Either ore or gangue may be labeled.

Jan 1, 1980

By C. D. Litton, I. E. Perera

This report presents the results of experiments to evaluate different types of mine fire sensors in an underground mine environment using a commercially available atmospheric monitoring system. To determine how well carbon monoxide (CO) and smoke sensors respond for purposes of fire detection, experiments were conducted using test fires of different mine combustibles and for both flaming and nonflaming combustion. The experiments were designed to assess the response of fire sensors to different contaminants and different contaminant levels produced from the test fires. The experiments were performed in the Safety Research Coal Mine at the U.S. National Institute for Occupational Safety and Health’s Bruceton Research Facility in the presence of an average ventilating air velocity of 1.6 m/s (315 fpm). Five fire sensor stations were located downstream of the test fire at fixed locations, with each sensor station consisting of four sensors: a CO fire sensor and three different smoke sensors, of which two were evaluated by the Mine Safety and Health Administration (MSHA) for intrinsic safety and the third was used extensively in underground mines overseas but not evaluated by MSHA for intrinsic safety. All four sensors were mounted near the center of the entry and in the upper onethird of the entry height. A UL-listed combination ionization and photoelectric smoke sensor was mounted near the roof at the first sensor station and its responses were compared against the responses of the four CO and smoke fire sensors. Sensor response data, contaminant travel times, and the impact of fire on the existing ventilation flow are discussed as they apply to earlywarning fire detection. Of significance in the analysis is the need for performance standards for mine fire sensors in order to provide for consistent and timely early warning of developing fires.

Jan 1, 2014

By Ataç Başçetin, Hasan Çelt, Hüseyin Onur Dönmez, Kürşat Hasözdemir

Phenolic foams, known for fire resistance, show broader industrial potential, particularly in mining, through property enhancements. Adjustments to the formaldehyde-to-phenol (F/P) ratio, bio-based additives like lignin, and nano-silica improve foam strength and thermal stability. Density modifications allow foams to range from flexible, low-density forms to rigid, high-density supports. In mining, enhanced phenolic foams could reduce coal ignition risks by acting as oxygen-blocking barriers. Current findings suggest these foams offer viable, sustainable solutions for safety in hazardous environments. Continued development could make them essential for thermal and mechanical applications under extreme conditions. This paper aims to provide a comprehensive overview of the mechanical characteristics of phenolic foams, current enhancement strategies, and standardized testing methods used to evaluate foam properties.

Feb 1, 2025

By MARK J. VANARELLI

Estimating ground-water inflows in rock deep tunnels is critical to the safety of personnel constructing the tunnel and the cost of construction. This paper presents two case studies, including the Chattahoochee and Nancy Creek tunnels, for estimating steady-state ground-water inflows into deep rock tunnels. Statistical methods were applied to packer test data obtained from exploratory borings during geotechnical site investigations, and a semiempirical procedure was used to estimate ground-water inflows. The Chattahoochee and Nancy Creek tunnels are deep rock tunnels that exhibit radial flow conditions. For the radial flow condition, a statistical analysis presented in this paper indicates that the semiempirical procedure works well; however, variations in the procedure and/or an insufficient amount of testing could lead to underestimations of the inflow quantities. Modeling using Monte Carlo simulations was observed to be an effective tool for removing data distribution irregularities and incorporating high-end permeability data to derive reasonable ground-water inflow estimates.

By J. S. Hu

FTIR spectroscopy has been used for the characterization of adsorbed oleate at the fluorite surface. It has been found that modest changes in the adsorption density at high temperature and high oxygen potential do not provide a satisfactory explanation for the significant increase in the hydrophobic character of the system under similar conditions. Rather, FTIR spectroscopic measurements suggest that chemical interaction between adsorbed oleyl groups occurs at high temperature and/or oxygen potential and accounts for the increased hydrophobicity. Specifically, the intensity of the =CH bond of the adsorbed oleate diminishes at high temperature and/or high oxygen potential. Such a phenomenon was not observed in control tests with the calcium oleate soap. For extensive reaction at the fluorite surface, the presence of a new surface species has been identified. These results indicate that the fluorite surface catalyzes an oxidation and/or polymerization reaction between adsorbed oleyl groups which results in a more hydrophobic structure at the fluorite surface.

Jan 1, 1986

By Steve Rogers

Nautilus Minerals was listed on the Toronto Stock Exchange in May 2006. The company now has major mining companies Anglo America (5.7%), Teck Cominco (7.2%) and Epion Holdings (22.4%) as significant shareholders, and has raised approximately $US346 million dollars to develop the world's first deep-water mine. The company is currently targeting high-grade copper and gold in seafloor massive sulphide mineralization, located near plate boundaries in back-arch basins of the Western Pacific. The first mine scheduled to be developed by the company is located in 1,600 meters of water at Solwara 1, in the relatively quite waters of the Bismarck Sea approximately 50 km from the port of Rabaul, within the Territorial Waters of Papua New Guinea. During 2006 and 2007 the company completed detailed environmental and geological studies, culminating in a number of world firsts, including the world?s first NI 43-101 compliant resource statement and environmental impact study for a seafloor massive sulphide system. Permitting is well advanced for the project, with initial production scheduled for late 2010, subject to timely grant of the permits. Extensive government and stakeholder liaison and engagement has been undertaken throughout the projects life, and is a core feature of Nautilus' desire to "do it right" in all aspects of this new industry.

Jan 1, 2008

By K. V. K. Prasad

Forecasting mined grade variability from exploration information is a challenging task in mine planning. For effective planning of activities such as workplace scheduling, ore grade quality control etc. development of realistic numerical/simulation models of in-situ variability from exploration information is an essential first step. Geostatistical conditional simulation (GCS) is one of the well known methods to develop these simulations. Recently, stochastic fractal models based on the assumptions of scale-in variance and self-similarity have been used for developing simulations of several natural phenomena. It has been suggested that these models might permit generation of short-scale variability information from exploration data with greater fidelity when the data satisfies the attendant assumptions. In this paper the stochastic fractal models are reviewed and their relationship to geostatistical variogram models is examined. A comparison of the two simulation techniques has been per-formed using coal sulfur data from a mined out coal property. The results of this comparative analysis are also presented in the paper.

Jan 1, 1992

This study was conducted to evaluate the effects of a diesel particulate filter (DPF) regeneration process on the concentrations and size distributions of aerosols in an underground mine. Two active regeneration strategies were examined for an electrically regenerated sintered metal fiber filtration system, and the effects were compared with those observed for a muffler and the same system operated in a passive configuration. The effects were assessed for three steady-state engine operating conditions. The number and mass concentrations and size distributions of aerosols in mine air were found to be strongly affected by the exhaust configuration, engine operating conditions and the regeneration process. When the system was operated in active configurations, the concentrations exhibited a transient and cyclic nature. At light load conditions, the distributions of aerosols in mine air were dominated by accumulation mode aerosols for all exhaust configurations and regeneration strategies. High concentrations of nucleation aerosols were observed when the DPF system was used and the engine was operated at high load conditions. A positive correlation between accumulation of particulate matter in the filter and the efficiency of the filter in removing accumulation mode aerosols was observed for all conditions. In the case of high engine load, reductions in accumulation mode aerosol concentrations were linked to a substantial increase in number concentrations of nucleation mode aerosol. Overall, the filtration system was found to be very effective in reducing total aerosol mass and elemental carbon concentrations for all engine operating conditions. However, the system was substantially more effective in passive than in active regeneration configurations.

Jan 1, 2012

By John Newby, Mahmood Khwaja, Bernard Theron, Janice McGovern, Bernard Catalano, Michael S. Schultz

Launching a full-size pressurized-face Tunnel Boring Machine (TBM) in difficult ground conditions is always challenging. Recently, few projects have innovated the process by scaling the trenchless method of pipe jacking, and modified steel bell approach, to facilitate the launching of a full-size TBM without the need for large and deep trenches, starter/tail tunnels, or for incrementally installing supporting gear as the machine advances. This paper presents three such projects; evaluates the post-bid contractor proposed modifications; details the innovative use of pre-cast pipe segments to facilitate machine launch; and, provides an overall assessment of the benefits, challenges and lessons learned related to the modified approach.

Jun 13, 2021

By J. Edberg

"This article details the use of an alternative testing method to the 2004 "Post-Tensioning Institute (PTI) Recommendations for Prestressed Rock and Soil Anchors" manual’s recommendations for temporary and permanent rock anchors for applications in shafts and tunnels. This method was developed and used for the Black River Tunnel (BRT) project in Lorain, OH as a means to reduce testing time of rock bolts during shaft construction while maintaining a similar level of quality control and assurance. The following sections will detail the project background, subsurface characteristics, shaft construction, the 2004 PTI testing method and associated difficulties, the alternative testing method and conclusions reached.Project backgroundThe city of Lorain is located in north central Ohio on the south shore of Lake Erie, approximately 40 km (25 miles) west of Cleveland and 119 km (74 miles) east of Toledo. The city chose to build a large-diameter storage tunnel and pump station to meet its requirements to reduce sanitary sewer overflows to the nearby Black River. NTH Consultants Ltd. (NTH) was retained by the city’s prime consultant, Malcolm Pirnie Inc. (now the water division of Arcadis), to perform a geotechnical investigation, develop design and construction bid documents for the tunnel and shaft liner systems and ultimately provide oversight assistance during the construction phase of the project.The BRT is an approximately 1,700-m (5,560-ft) long, 7-m (23-ft) diameter rock tunnel to be lined with a 5.8-m (19-ft) inside diameter secondary concrete lining (Fig. 1). The tunnel is designed to accept flow at a new drop shaft (Shaft 3) located on the west side of the Black River, across from the city of Lorain Black River waste water treatment plant (BRWWTP). The tunnel will be dewatered at the south end by a large diameter pump station (Shaft 1) located in the existing Lorain Port Authority Public Boat Launch. Flow from the new pump station will be discharged into an existing shallow interceptor sewer and directed back to the BRWWTP."

Jan 1, 2014

By Z. Henderson, J. R. Saylor, L. Rojas-Mendoza

"Diesel particulate matter (DPM) is a major occupational health hazard in underground mine environments, even with available abatement technologies. Prior work has demonstrated that micrometer-scale water droplets, or “fog,” may be effective in removing significant number fractions of DPM from a conditioned exhaust stream. Here, a series of laboratory experiments are described which demonstrate that such a treatment can remove significant DPM mass from an unconditioned stream. The removal mechanism involved coagulation of the DPM and drops. The fog treatment removed about 45 percent more DPM mass on average than no treatment. Varying engine load, flow rate and fog droplet number density did not significantly affect the results under the range of conditions tested. IntroductionDiesel engines have seen widespread use for well over a century due to their relatively high thermal efficiency and fuel economy (Heywood, 1988). Recently, however, the adverse health risks of diesel exhaust have become increasingly clear. The term diesel particulate matter (DPM) is used to refer to the solid components of diesel exhaust, which are an ultrafine mixture of elemental and organic carbon (EC and OC) and minor constituents including sulfates and metal ash (Kittelson, 1997). DPM is generally considered to occur almost entirely in the submicrometer range. It is classified as a carcinogen (Occupational Safety and Health Administration, 2013), and epidemiological studies have demonstrated a positive correlation between long-term exposure to DPM and other combustionrelated fine particulates and increased cardiovascular and pulmonary diseases (Pope et al., 2002; McDonald et al., 2011). Many of the risks of diesel exhaust are associated with the physical and chemical properties of exhaust components (Heywood, 1988; El-Shobokshy, 1994; Kittelson, 1997). Exposures are generally measured and regulated on the basis of mass concentration. However, DPM number density and particle size are increasingly recognized as critical factors in terms of health outcomes (Bugarski et al., 2012; Kittelson, 1997; Occupational Safety and Health Administration, 2013; Pope et al., 2002)."

Jan 11, 2017