Search Documents

By Jr. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is always the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxidation practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel.

Jan 1, 1931

By C. H. Herty

Manufacturers and consumers of steel have come to realize during the past few years that cleanliness is of great importance in steels which must meet rigid specifications for various physical properties. Of equal importance is the consistent production of steel which is uniform in these properties. For maximum utility, steels should be uniform not only from heat to heat, but also from ingot to ingot and within each ingot. In the manufacture of killed steels such as the higher carbon forging grades, uniformity as indicated by the usual chemical analysis is easy to obtain, provided that a normal top discard is taken, as is al¬ways the case in steels poured with hot-top practice. No such uniformity, however, holds true for the nonmetallic matter, which consists for the most part of the products of deoxidation of the steel. For a large tonnage of steels which go into articles manufactured by deep-drawing processes, killed steel has never been successfully applied because with the present deoxida¬tion practice, low-carbon killed steel is almost invariably extremely dirty. To obtain the desired qualities for deep drawing, the steel is rimmed, - that is to say, deoxidized with manganese and perhaps a small amount of aluminum, - the resultant product being of high purity in the skin of the ingot, but very badly segregated at the center of the ingot, particularly in the upper-central section. This segregation necessitates a very heavy top discard, and one of the major segregates is carbon which renders the steel too hard to draw properly. If clean, low-carbon killed steel could be made successfully, much better ingot yields would be obtained than by the present rimming steel practice. Furthermore, banded structures and outside and inside seams, which are undoubtedly due in a large measure to blowholes in the ingot, are defects which are very difficult to control in rimmed steel. These defects would be minimized by clean killed steel.

Jan 1, 1931

By W. V. Kuster

The investigation described in this report is part of a survey by the Federal Bureau of Mines of the titanium resources of the United States. The purpose of this project was to study a typical coastal deposit of beach sands in the Middle Atlantic States, particularly in the area surrounding the Delmarva Peninsula. The field investigation consisted of a reconnaissance survey of the Eastern Shore of Maryland, followed by surface sampling and drilling of the sands on Assateague Island, off the Atlantic coast of Maryland. The study covered the period January-December 1957. Detailed analyses were made of 5-foot sections of eight drill holes along the Maryland section of the island. The heavy-mineral fraction of these samples was separated by sink-float tests, using acetylene bromide as the heavy liquid. The minerals comprising the heavy fraction were examined microscopically, and mineral counts were made on selected samples.

Jan 1, 1959

By Arthur L. Murray

The first thought in the case of an accident or contagious disease is naturally that aroused by our humane instinct , how serious is the case and will the person recover ? The economic effects of such cases , owing to their many ramifications , are seldom realized either by those directing mining operations or those engaged in the labor of producing . This paper is based on the accident experience of the State of Utah and the number of cases of two well known preventable diseases , typhoid fever and smallpox , in that State for the fiscal years 1917-1918 , 1918-1919 , 1919-1920 , and 1920-1921 . The data and figures presented are from coal -mining camps only . W. W. Adams , mine- accident statistician of the bureau, contributed valuable corrections and suggestions . The economic results of accidents are considered first , and those of the two preventable diseases later .

Apr 1, 1922

By A. B. Hooker

A list of permissible mine equipment, tested and approved by the Bureau r. Mines previous to January l, i-)4, , was published in Bureau c Moines In ornation Circular 7207.3/ The l ,.t c -. that dote was complete as to equipmentthen available and in current Information Circular 7210,?+/ published as a supplement thereto, listed equipment approved during; the calendar 1942. Information Circular72x'3,_/ published as a second supplement thereto, ! listed equipment approved during the calendar year 1943. The present listis. Another supplement covering approvals issued during the calendar year 1c)44. The items are numbered crud to indicate the consecutive order in which each typo of machine or device was approved _.c?. in its particular classification. Thus Information Circular 7207 gave 1,t drills and drilling much fines on the Bureau'sactive.. d active list Ih: additional anal approval: were given in 1942 the three issued in 19 and one issued :n 1944- bring the total to `3. Item 111, under. Loading Machines and conveying appeared in lnformation Circular 7207. It is repeated ',tore to _how that on j,,l was granted Curia 1the optional of this loader when modified .'or 2 0. alt ciruits .]

Jan 1, 1945

By Will H. Coghill

[The supply of gravel spar and of acid spar is not well balanced. Gravel spar -- 85 per cent flourspar, 5 per cent silica -- gluts the market, whereas acid spar -- 98 per cent fluorspar, 1 per cent silica -- is somewhat scarce. Hence it is desirable to convert some of the gravel spar into acid spar. Knowledge of this condition prompted the Franklin. Fluorsrar Co. at Paducah. Ky., to enter into cooperation with the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy to improve the methods of fluorspar, milling so that morn acid spar would be available. The fluorspar company detailed Mr. Omar Greeman for the work. During the course of the investigation, while Mr. Greeman was also doing work for a master's degree in the School of Mines? an extensive study was made of gravity concentration of fluorspar ores. Decrepitation by heat treatment was also given a laboratory try-out. A part of tie time was spent on flotation; these notes relate only to the flotation. The results of one of the flotation runs is appended. The test was made in a 500-gram mechanical-agitation machine. The sample was ground to 100-mesh in a pebble mill.]

Jan 1, 1928

By George H. Holmes

This report describes the results of a reconnaissance survey of areas in California and Nevada considered favorable to beryllium mineralization. Pegmatite dikes, veins, intrusive sills, contact metamorphic, and disseminated deposits as well as tactite deposits in the former major tungsten-producing districts were investigated. A general geographic pattern of beryllium mineralization was found to be concentrated along a wide belt in eastern Nevada extending from the Ruby Mountains, Elko County, south through the Fish Creek Range, Eureka County, the Snake Range, White Pine County to the Virgin Mountains in Clark County, Nev., and Mohave County, Ariz. Sporadic occurrences of beryllium are in central and southern Nevada, and in the pegmatite dikes of San Bernardino, Riverside, and San Diego Counties, Calif., and the granite masses of the southern Inyo Mountains, Inyo County, Calif. Principal company activities are centered in the Snake Range, Fish Creek Range, and the Virgin Mountains, Nev., and the Inyo Mountains, Calif. Other areas in California and Nevada have been superficially explored with results indicating either limited or widespread, but submarginal, mineralization. Although beryllium was found to occur, to some extent, in many of the deposits, mining has been hindered by the lack of a market for beryllium ores and concentrates other than standard-grade beryl and also by the erratic pattern of mineralization and the high exploration and beneficiation costs required to produce a marketable product.

Jan 1, 1963

By George H. Holmes

This report describes the results of a reconnaissance survey of areas in California and Nevada considered favorable to beryllium mineralization. Pegmatite dikes, veins, intrusive sills, contact. metamorphic, and disseminated deposits as well as tactite deposits in the former major tungsten-producing districts were investigated. A general geographic pattern of beryllium mineralization was found to be concentrated along a wide belt in eastern Nevada extending from the Ruby Mountains, Elko County, south through the Fish Creek Range, Eureka County, the Snake Range, White Pine County to the Virgin Mountains in Clark County, Nev., and Mohave County, Ariz. Sporadic occurrences of beryllium are in central and southern Nevada, and in the pegmatite dikes of San Bernardino, Riverside, and San Diego Counties, Calif., and the granite masses of the southern Inyo Mountains, Inyo County, Calif. Principal company activities are centered in the Snake Range, Fish Creek Range, and the Virgin Mountains, Nev., and the Inyo Mountains, Calif. Other areas in California and Nevada have been superficially explored with results indicating either limited or widespread, but submarginal, mineralization. Although beryllium was found to occur, to some extent, in many of the deposits, mining has been hindered by the lack of a market for beryllium ores and concentrates other than standard-grade beryl and also by the erratic pattern of mineralization and the high exploration and beneficiation costs required to produce a marketable product.

Jan 1, 1963

By Maria I. De Rosa

During 1990-2001, a total of 518 fires occurred in all metal/ nonmetal mining categories; 296 of those fires caused 308 injuries and 4 fatalities. Surface operations had the most fires and the highest injury risk rate values. Forty-five fires destroyed or heavily damaged facilities and equipment (including 19 pieces of mobile equipment) because of failure of firefighting methods, late fire detection, undetected fires, or fire size. In the future, many of these fires and injuries might be prevented or detected and extinguished at their earliest stage by improving current fire safety procedures, adopting existing/ improved fire detection and suppression technologies, and/or developing new technologies. Several strategies for reducing and/or preventing the number of fires and fire injuries follow. I. Increase vigilance, improve safety procedures, and develop new technologies in order to prevent fires and injuries caused by fame cutting and welding operations. 2. Improve equipment hydraulic/fuel/electrical systems inspection programs; adopt fire-resistant hydraulic fluids and electrically powered motors for use in underground mines; develop new technologies (equipment/cab rapid fire detection/ prevention/suppression systems, emergency line drainage systems, and fire barriers); adopt an optimal ground level location for the activation of emergency systems; improve operator's fire preparedness training programs; and develop effective and rapid local firefighting response capabilities. 3. Adopt existing/improved systems for continuous and early detection of combustion gases and smoke along beltlines. 4. Adopt existing/improved technologies for monitoring equipment (beltlines) operational functions. 5. Increase vigilance and adopt improved safety procedures for handling f amenable liquids and refueling fuel in the vicinity of heat sources.

Jan 1, 2004

By Christopher Van Dyke, Knox Van Dyke, Lixin Wu, Jaime Gutierrez

"I. INTRODUCTION(SILICA, THE LUNG, INFLAMMATION, AND FIBROSIS)Inhalation of respirable-size silica (0. I to 5 µm in diameter) deposits the particles in the deep spaces of the Jung where oxygen is exchanged. The resulting pattern of inflammation is substantially different compared to that observed from other inhaled substances such as carbon, polystyrene titanium dioxide etc. 1 Following the inflammatory reaction the body attempts to isolate the damage by walling off the area via fibrosis. 2 The unique nature of the inflammatory response to silica makes it logical to infer that fibrosis is a later-stage manifestation of the initial inflammatory damage. In addition to the inflammation extensive lysis and cellular death particularly to macrophages and neutrophils, can occur, depending on the dose of silica.' The ingestion of significant amounts of silica by macrophages and neutrophils produces an inflammatory sequence which activates the lipoxygenase pathway of arachidonic acid metabolism and produces platelet activating factor (PAF) and leukotrienes (LT).4·5II. CALCIUM IONOPHORE MIMICS SILICA TOXICITY IN VITROPhagocytic cells exposed to silica in vitro produce PAF and LT. This response is reminiscent of phagocytic cells exposed to the calcium ionophore (A23 l 87) in the presence of ionic calcium.6-8 A23 l 87 forms a complex with free ionic calcium which passes through cellular membranes, thus transporting calcium inside the cell. The increased intracellular calcium concentration triggers the production of small amounts of prostaglandins large amounts of LT. PAF and. depending on dose cellular death (see Figure 1 ). Could silica cause LT production and cellular death by a similar mechanism? How could silica - an inert solid - act in a similar fashion as a soluble stimulant? Clearly the negative SiO2 and OH- surface of silica can bind calcium ions9 and therefore could theoretically act as a solid-state ionophore releasing bound calcium inside of cells following phagocytosis."

Jan 1, 1998

By D. B. McGilvra

This paper, describing the mining practices and methods at the Black Rock mine, is one of a series of similar papers on mining methods in the various mines of the United States being prepared by the Bureau of Mines. The Black Rock mine is located in the northeast corner of the Butte district, about 3 miles from the center of the town of Butte, and is owned and operated by the Butte & Superior Mining Co.

Jan 1, 1930

By W. L. Parker, W. A. Selvig

"Introduction.Powdered or pulverized coal is extensively used as a fuel, the total annual consumption*** in the United States being about 12.000,000 tons, and growing steadily. As the coal is usually pulverized so that 70 per cent or more parses through a 200-mesh sieve, it presents difficulties in sieving, because such finely divided material tends to clog the meshes. A fineness test is desirable in order to judge the efficiency of the pulverizing apparatus, and as an indication of the particle size of the coal being burned.Committee D-5 on Coal and Coke, American Society for Testing Materials, has recognized the desirability' of a standard method for determination of fineness of powdered coal. The Bureau of Mines, in co-operation with this Committee, conducted sieving tests on two standard samples of powdered coal, which are described in this paper. As a result of this work a method for making fineness tests, by band sieving, is recommended as a standard method, while a rapid method, by machine sieving, is given for routine tests.Outline of Investigation.Preliminary trial tests were made by the bureau and tentative methods were formulated for making the sieving tests both by band and by machine.Each of two samples of powdered coal was carefully mixed, and portions were sent to the twelve laboratories mentioned later. These were requested to make duplicate sieving tests on the two standard samples, by the hand-sieving and machine-sieving methods, and to follow the tentative procedure exactly as outlined. All of the laboratories made sieving tests by hand shaking and eight of them made tests by machine shaking."

Nov 1, 1923

By L. M. Chan, D. R. Carlson, J. H. Johnson

"This paper presents an apparatus and procedures to implement a methodology for controlling ambient air quality in a confined working environment, such as an underground mine, an underground storage area, or a tunnel. The air quality control methodology is directed at limiting the quantities of exhaust pollutants emitted by diesel-powered vehicles into the confined space by identifying vehicles that are excessive polluters. The methodology is based on tailpipe and ambient air measurements in the confined space, and the ambient air threshold limit values (TLVs) for the various diesel exhaust pollutants. The methodology consists of two computational methods; a deterioration criteria computational method to identify excessive polluting vehicles, and an engine performance computational method to determine engine performance and to provide information needed to diagnose engine faults. The methodology is designed for implementation in conjunction with a preventive maintenance program.The first part of the paper describes the mine air and tailpipe emissions measurement apparatus and techniques used to obtain data. This is followed by sections discussing the deterioration criteria and the engine performance computational methods. A section discussing some common engine emissions-related faults is also presented lastly, a proposed procedure to implement the methodology including a possible hierarchical structure for mine personnel involved to implement the procedures is presented.INTRODUCTIONDiesel-powered mining vehicles are gaining Popularity in underground coal mines and are almost universally used in underground non-coal mines due to their mobility, flexibility, and higher productivity. However, noxious gases and particulate matter in diesel engine exhaust are a concern because of the potential for being harmful to the health of miners. Diesel exhaust pollutant concentrations out the tailpipe of a mine vehicle change with time due to engine wear, inadequate maintenance, improper adjustments and other factors. This deterioration in pollutant concentrations, if not properly controlled, may adversely affect the air quality in an underground mine. To provide assurance that a clean and healthful work environment are maintained, a program is needed to identify and repair diesel engines that contribute to poor air quality. Also, earlier detection of deteriorated engines will make preventive maintenance possible, thereby eliminating further deterioration and possibly complete breakdown. Preventive maintenance also increases engine life and equipment availability in production which in turn will result in decreased operating costs."

Nov 1, 1995

By Paris V. Brough

This paper, which describes the practice of milling custom ore, in addition to that produced under company and lease operations in the Tom Reed mines, is one of a series 'being prepared by the Bureau of Mines. ACKNOWLEDGMENT Acknowledgment is made to W. B. Phelps, managing director, and Jack Zwinge, superintendent, far permission to publish, a-ad to G. E. Jarpe, the present mill superintendent, for his assistance in preparing the paper. LOCATION The mill is in Oatman, adjacent to the Benjamin Harrison shaft of the Tom Reed Gold Mines Co., in the foothills on the western slope of the Black Mountains, western Mohave County. The railroad shipping point is Kingman, Ariz., 25 miles northeast of Oatman. Paved highway U. S. 66 passes by the mill. The altitude is approximately 2,700 feet.

Jan 1, 1937

By C. B. Manula, R. L. Sanford, R. A. Rivell

A - Contains the coordinate pair information for deriving the co¬efficients of the 3rd degree polynomial which approximates the loading station equation. C(N) - Coefficients for third degree approximating polynomial. I - General DO LOOP variable. K - Position in BRANCH of next character. L - Format specification in DEFINE FILE statement. X - Uniform displacement for random uniform number. Y - Load increment At. AO-A3 - Coefficients of approximating polynomial for loading station equation. GR - Grade direction, or grade resistance. IQ - Counts quadruples of distance grade speed and end of route for determining total distance. IT - Intersection counter in XXXDEF. Il - Station number trip is leaving. Jl - Station number for trip destination. J2-J8 - Motor assignments and functions for given trip. KK - Location of starting grade and distance in DISTGR KK - Position of decimal point in real number. KZ - DO LOOP variable for motor assignment check. LL - Location of ending grade and distance in DISTGR. Ll - Position in IECB of station satisfied. L3 - Next available position for IECB sort. MM - Flag for printing the failure of sanding to overcome slippage. NN - Trip destination in MOTSER RR - Rolling Resistance. XK - Station level or type.

Jan 1, 1974

By J. A. Herdlick

"INTRODUCTION The Bureau of Mines began a broad program of exploration of various proportion in the Pine Creek area of the Coeur d'Alene mining region in the fall of 1943. As a part of this project, exploring was done at theLittle Pittsburg property in 1945. The work included driving a 500-foot crosscut from the No, 6 level and drilling four diamond core drill holes to test the behavior of the Little Pittsburg vein at depth. This report presents the data obtained by the Bureau.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyses samples and performs beneficiation tests.The Bureau's exploration of the Little Pittsburg vein was one of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. The project was started by R. M. Gammell, mining engineer, and was continued by the author and J. R. Reynolds, assistant mining engineer.The chemical analyses included in this report were made at Reno, Nov., under the direction of A.C, Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines.The cooperation and assistance of the management of the Denver Development Co. is gratefully acknowledged, in particular that of C. E. Nugent, who made available much of the operational data included in this report."

Jan 1, 1947

By Jun Yi

In this paper, single-component gas sorption and transient diffusion processes are described within coal matrix exhibiting bimodal pore structure. The coal matrix is treated as a poroelastic medium manifesting swelling and shrinkage effects due to the sorption of gas under effective overburden stress. Gas transport is considered Fickian with molecular (bulk) and surface diffusion processes simultaneously taking place in the macro-and micropores of coal, respectively. The numerical formulation is intended to be explicit in nature to investigate the influences of sorption phenomena on the macropore volumes and on the overall gas transport for the cases of gas uptake by and release from coal. Results of the study show the presence of hysteresis during a sorption?desorption cycle of the gas. It is also found that the overall gas transport takes place at a rate significantly less than that in the macropores only. Thus the existence of a retardation effect in the overall gas transport is concluded. This retardation effect is primarily due to the micropore resistances, in particular gas adsorption, and is independent of the changes in the macropore volumes. It is shown that macroporosity of the coal matrix may change during gas transport due to combined effects of pressure and sorption-induced swelling or shrinkage of the coal. It is estimated that the macroporosity variation is non-uniform in space and time, as it is expected in reality, and typically taking values less than ±10 percent of the initial porosity.

Jan 1, 2009

By W. O. Philbrook

Reduced-scale models have long been used in hydrodynamics, aerodynamics, and heat transfer for studying fundamental flow relations or the performance of prototype designs under prescribed conditions. The pilot plant is a common tool of chemical engineering for investigating process variables and as an integral step in developing a new process. The metallurgical industry was rather slow to recognize the applicability of these techniques to some of its established and rather complex processes, but there has been a rapidly increasing number of applications of the principles of modeling in process metallurgy since World War II. Not only have pilot-scale operations been employed for developing methods of extracting metals that have recently achieved commercial importance, as well as new processes for some of the commoner metals, but models have also been used for engineering studies aimed at better understanding of the controlling, variables of time-honored conventional processes, It appears that the principles of similitude have become accepted as a useful tool, when properly applied, in metallurgy as in other fields of engineering. Much of the work of the Pyrometallurgical Laboratory, Region V, involves study of high-temperature smelting and refining processes for ferrous and related metals in pilot-scale equipment, such as the experimental blast furnace, converter, open-hearth, arc furnace, and rotary kiln. It was appropriate for the work of this laboratory that guiding principles for designing apparatus and interpreting results should be set down and that a bibliography of related work should be available for reference. A summary of the principles of model study and a brief review of some of the more noteworthy general papers have been published elsewhere.3/ Also, the Bureau of mines plans to publish a report of investigations describing its experimental work in this field. The bibliography is presented here as a service to others who may have use for it.

Jan 1, 1958

By R. W. Stahl

One of the broad purposes of the Bureau of' Mines since its establishment has been conservation of mineral resources. As some of the coal beds approach depletion, especially those coals suitable for making metallurgical coke, more and more attention is being given to means of recovering a larger percentage of coal in place. The customary system of mining in the United States is by room and pillar, or some variation thereof, which leaves pillars of coal to support, the roof. In many operations, where the pillars are not systematically recovered, the loss of coal often amounts to 50 percent or more of the original deposit. In many instances in developing new mines, It is planned to recover chain and barrier pillars on retreat when the mine has reached established boundaries. Too often, however, mines are abandoned for some unforeseen reason before completion of mining without recovering any pillars. Usually, these pillars are lost forever. With this in mind, the Mining Division, Region VIII, of the Bureau; of Mines is encouraging mining by longwall methods. It is a generally known fact that almost all of the European coal is mined by longwall methods, which are conducive to a high percentage recovery of coal. A comparison between mining systems usually is on the basis of tons per man per shift. Unless all operating conditions are similar, such a comparison could be misleading. Generally, the output per man shift in European longwall mines is less than that obtained in room-and-pillar mining in the United States. In European mining, maximum recovery of coal is not only mandatory but it must be accomplished without major damage to surface by subsidence. These restrictions necessitate packing or stowing with consequential increases In manpower and decreases in output per man shift.

Jan 1, 1954

By Wm. F. Netzeband

The purpose of this paper is to present to the operators, in other districts a detailed description of the ruining method used and the results obtained to exploiting one of the zinc-lead deposits of the Kansas-Oklahoma-Missouri district. No. 1. mine is located in the heart of the town of Picher in the extreme northeast corner of Oklahoma. HISTORY The first prospect drilling was done at No. 1 mine late in-1914, and shaft sinking was started early in 1915. Sufficient ore was developed to start construction of the mill in April, 1016, Production begin in August, 1916, and the mine s been producing, except for short periods, to the present time. The property was originally a 40-acre tract, but additional properties have been consolidated with the original one until the mine now covers 200 acres.

Jan 1, 1929