Search Documents

By Ann G. Kim

Hydrocarbon gases, primarily methane but also the C2 through C5 paraffins, the C2 and C3 olefins and possibly the C4 and C5 olefins, are byproducts of coal formation. Although it is generally believed that coal formation occurred at temperatures below 200° C, most experimental work on gas formation from coal has been performed at temperatures between 200° and 1,000°C. The objective of this Bureau of Mines experiment was to determine if observable changes in the gases from coal could be produced at temperatures below 200° C in relatively short periods of time. The experiment involved heating coal samples from six coalbeds at constant temperatures and analyzing evolved gases. The composition of the gases at three temperatures was compared. At 35° C, over 99 pct of the gas is methane; at 125° and 150°, methane constitutes approximately half of the hydrocarbon gas. Isobutane and pentane are the predominant higher hydrocarbons at temperatures between 100° and 150° C.

Jan 1, 1974

By T. T. Campbell

This report traces the development of techniques for the preparation of high-purity rare-earth metals. Rare-earth metals, excepting samarium, europium, and ytterbium, were prepared by converting their oxides to anhydrous chlorides or fluorides and reducing the rare-earth halides with active metals such as lithium or calcium. High-purity, anhydrous rare-earth chlorides were prepared by dissolving the rare-earth oxides in hydrochloric acid to form hydrated chlorides and by subsequently dehydrating the hydrated salts in the presence of ammonium chloride at temperatures ranging from 70° to 360° C. while under reduced pressure (50 microns to 1 inch Hg). The chlorides were also prepared by direct chlorination of rare-earth oxide-carbon mixtures. Reaction efficiencies in excess of 95 percent were obtained by either method; however, purer chlorides were prepared by the aqueous ammonium chloride conversion method. Purification of yttrium chloride by high-temperature vacuum distillation proved to be an effective method of separating, oxygen-bearing compounds from the chloride. Yttrium metal prepared from purified chloride contained significantly smaller amounts of oxygen (990 p.p.m. oxygen in yttrium metal prepared from raw chloride and 200 p.p.m. in that prepared from distilled chloride).

Jan 1, 1961

By J. M. Stuve

Low-temperature heat capacities and the enthalpy of formation were deter-mined calorimetrically by the Bureau of Mines for CuO?CuS04. The derived standard entropy (S°298.15) was 40.36±0.04 cal/deg-mole, and the enthalpy of formation (?H°f) was -219.l±0.3 kcal/g-mole. A large thermal anomaly was observed in the heat capacity of CuO?CuS04 at 20±0.1 K. Gibbs energy of formation data are tabulated up to 1,200 K. Construction details of a precision low-temperature adiabatic calorimeter capable of determining heat capacities of solids in the temperature range 5 to 320 K are given. A calibrated miniature germanium resistance thermometer was incorporated into the calorimeter to extend the range of accurate measurements below 15 K. High-resistance dc heater windings were used throughout the cryostat to reduce heat conduction of inner connecting wires.

Jan 1, 1975

By C. W. Sill

[In the original Norris and Fay method for determining selenium, selenious acid is reduced by an excess of standard thicsulfate in accordance with the following reaction: H2Se03 + 4Na2S203 + 4HC1 = Na2SeS406 + Na2S406 + 4NaC1 + X20. (1) The excess thiosutfate is then back-titrated with standard iodine solution. The disadvantages of ouch a method are obvious. On an unknown sample, the quantity of thiosutfate required would be difficult to determine; a definite excess is required, but large back titrations would be undesirable. Inasmuch as thiosulfate is decomposed by acid, considerable error may be introduced in this method, the amount depending on the acidity, temperature, concentration of excess thiosulfate, duration of contact between thiosulfate and acid, and other factors, In a critical study of the Norris and Fay method, Coleman and McCrosky3/ show that the method is accurate to less than .1 part per thousand if the excess of this sulfate Is not greater than 5 ml. of 0.1 N solution (in 1.0 ml. of 0.x4 N sulfuric acid) whether the titration is made at 0° or 20°C. A greater excess produced unsatisfactory values at either temperature. Coleman and McCrosky regulated the excess thiosulfate by adding 5-ml. portions of thiosulfate solution followed by the addition of 1 to 3 drops of 2.5 percent potassium iodide in the presence of starch. If a starch-iodine blue color formed locally around the drops of potassium Iodide, the reduction of selenious acid was not complete. On stirring the solution, the local blue color fades and another 5-ml. portion of thiosulfate is added. When addition of potassium iodide fails to produce a local blue color, reduction of selenious acid is complete, and the excess thiosulfate is then back-titrated with standard Iodine solution. The number of equivalents involved in the reduction of selenious acid by either thiosulfate or iodide is the same, and therefore no correction need be made for the potassium iodide. This procedure is much better than the original Norris-Fay titration, but acidity and time would stilt be rather critical factors subject to variation with individual technique. Also, the method still requires the lose of two standard solutions, a rather undesirable factor from the standpoint of routine application.]

Jan 1, 1954

By N. Kyriazi

A performance study of oxygen self-rescuers from the United States and other countries was undertaken as an assessment of present worldwide technology. The apparatus were tested a an breathing and metabolic simulator in the Life Support laboratories of the Bureau of Mines. Parameters monitored during the testing were inhaled levels of C02 and 02, inhaled gas temperature, and breathing resistance. The metabolic demand placed on the apparatus represented the average demand of the 50th percentile miner performing a 60- min man-test 4, as described in 30 CFR 11H. Results presented include ;apparatus service life and subjective comments as well as averages and peaks of monitored parameters.

Jan 1, 1984

By H. F. MILLE, Charles A. Kumke

This paper describes mining operations at the Iron King mine of the Shattuck -Denn Mining Corp. in Yavapai County , Ariz . It is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices and methods in various mining districts of the United States . The mine and surface plant of the Iron King mine are situated in secs . 15 and 21 , T. 13 N. , R. 1 E. , about 20 miles by State highway 69 east by southeast from the city of Prescott and 1 mile southwest of the mining town of Humboldt on the Prescott -Mayer branch of the Atchison , Topeka & Santa Fe Railroad (fig . 1 ) . A l-mile truck haul brings the mill concentrates (lead and zinc ) to bins on a siding of this line at Humboldt ; the silver -gold bullion is handled separately . Some of the oldest residents in the vicinity of Prescott claim that the original location for the Iron King mine was made in 1880. The earliest recorded production was in 1906-1907 . During the first World War the mine produced fluxing ore for the Humboldt smelter . In 1936 the property was purchased under tax sale , and a mill (140-ton capacity ) was erected in 1938. The capacity of this mill was increased to 225 tons the following year , and a cyanide plant was added in 1940 to treat mill tailings . In 1942 the Shattuck -Denn Mining Corp. purchased the property . A new working shaft was sunk , mine development was speeded , and mill capacity was again increased . The predominating locally formation of this district is a pre -Cambrian schist known as Yavapai schist . The Iron King deposit , which carries gold, silver , lead , zinc , and copper , occurs as a series of lenses in a sheared zone of the pre -Cambrian schist . Down to the 600 -foot level the ore was mined and drawn by the shrinkage method . The cut -and -fill method was adopted for the lower levels . Waste rock for stope fill was provided by block-caving an area on the 600 level . Main haulage drifts were driven in the firm footwall , and crosscuts were driven across the mineralized zone at 100 -foot intervals . Grab samples taken from each car of every working place and channel samples cut every 5 feet in development work are considered sufficient for estimating ore reserves .

Jan 1, 1950

By J. J. Sammarco

Light emitting diodes (LEDs) are emerging as viable replacements for incandescent-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. The present paper describes the performance of LED and incandescent sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and airflow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Secondly, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and incandescent sources can be magnified toward the end of a 10­hour battery discharge cycle. Empirically, we have determined that after 8 hours at an ambient temperature of 25 °C, the average light output of an incandescent cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and airflow on the light output of an LED and incandescent cap lamp were conducted in the NIOSH Safety Research Coal Mine (SRCM). The LED cap lamp yielded a vertical average illuminance improvement of approximately 9.5% and the INC cap lamp yielded a vertical average illuminance degradation o f approximately 4%. The differences between LED and incandescent cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38 % more efficient than the incandescent cap lamp with a lead-acid battery at the end of the 10-hour driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the incandescent light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, especially given that the light output will decrease an additional 30% to 45% over the period of a 10-hour shift. The implications of the differences between LED and incandescent sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and incandescent cap lamp visual performance research.

Jan 1, 2008

By M. M. Wong, J. E. Klosterman

Scrap beryllium chips ( nominally 96 to 97 percent Be ) were electrore fined in a prototype cell with 408 lb of electrolyte composed of 52.4 mole - percent LiCl , 36.3 mole - percent KC1 , and 11.3 mole - percent BeCl2 . The cell temperature was 500 ° C. In a typical 10-3 /4 - hour deposition cycle , 0.415 pound of metal was produced ; the metal contained impurities in parts per million as follows : C , 700 ; 0 , 610 ; Al , 34 ; Ca , 32 ; Cu , 20 ; Fe , 25 ; Mg , 9 ; and Mn , 23 . Operation of the prototype cell for 2 years demonstrated that adapting the electrorefining process to an enlarged scale of operation presented few difficulties in mechanical functions , maintenance of optimum operating conditions , and control of product purity . After the spent anode feed was leached in a 5 - percent nitric acid solution and the fine - sized particles were removed , it was recycled in some tests . The metal produced was somewhat higher in impurities than metal from the fresh scrap chips .

Jan 1, 1964

By D. H. Platt

Data obtained from on-the-site observations have been compiled to describe the equipment and installation methods used for satisfactory suspension roof support in a large-diameter tunnel. Experimental roof bolting was undertaken from June 1950 until May 8, 1951, in the East Delaware tunnel, which is part of the Delaware aqueduct in Delaware and Sullivan Counties, N. Y. Revised suspension-roof-support plans and specifications were prepared during the spring of 1951 by the City of New York Board of Water Supply; these were approved by the State of New York Department of Labor April 13, 1951, and adopted by the City of New York Board of Water Supply on May 8, 1951.

Jan 1, 1952

By E. S. Shedd

Misch metal was electrowon from a treated bastnasite concentrate in a REF3-LiF-BaF2 electrolyte at 950° C. The metal was prepared and tapped from a 1,000-ampere cell, and nearly 100-percent utilization of the rare-earth oxide was achieved. Prolonged operation in a smaller cell (40 amperes) indicated that the composition of the misch metal product was reasonably constant, and no significant increase of impurities, with the exception of carbon, was noted.

Jan 1, 1970

By W. T. Wertman

A research program to aid development of better petroleum-recovery technology is in progress at the Appalachian Experiment Station, Bureau of Mines, Morgantown, W. Va. The work is part of the overall effort of the Federal Bureau of Mines to effect true conservation of the Nation's natural resources. Knowledge of the magnitude of the interstitial water content of oil-bearing formations is important to petroleum-reservoir engineers because of the influence of water on fluid flow during oil production and because of the significance of water volume in oil-reserve evaluation. Such information on Appalachian oil-bearing formations is needed to aid in planning secondary oil-recovery projects. Generally, the interstitial water content of oil sands can be estimated by one or more of the following methods: Analysis of cores obtained with oil-base drilling fluid, electric logging, restored-state or capillary-pressure tests, centrifuge tests, evaporation tests, or mercury-injection tests.

Jan 1, 1959

By Bertrand L. Johnson

As potash is more necessary to the agricultural economy of the United States now than ever before it is gratifying to find that the virtual stoppage of imports from Germany in late 1939 caused none of the anxious foreboding that gripped American farmers in 1914. For long decades this country, in common with tie rest of the world, depended upon German potash, but today our expanded needs can be mot from domestic sources. The present armed conflict in Europe, like that of 1914, disrupted a world monopoly, but the cartel that in recent years controlled 90 percent of the world output (see fig, 1) was an international syndicate comprising French, Polish, and Spanish as well as German producers and having reported sales agreements covering production in the U. S. S. R. and Palestine. The break-up of these commercial agreements has necessitated readjustments but generates no such alarm as the closing of a single source of supply. In striking contrast to the critical shortage that developed a quarter century ago, no increase in prices has occurred or is anticipated in the domestic market.

Jan 1, 1940

By K. C. Dean

The combination of flotation and chemical processing methods presented in this report of the Bureau of Mines enabled treatment of typical low-grade ferberite ores from the Boulder County, Colo. area, to produce specification-grade synthetic scheelite. The overall recovery from ore to synthetic scheelite was 87 percent, based on a flotation recovery of 93 percent and a similar recovery in chemical processing. Preliminary mineral dressing studies revealed that the physical and mineralogical nature of typical ferberite ores precluded high recovery of tungsten in plus 60-percent-W03-grade products by these methods. Therefore, the flotation research was focused on attaining plus 90-percent recovery in a concentrate containing 10 percent W03. Detailed studies were made (1) to establish optimum grinding conditions for obtaining adequate mineral liberation, (2) to develop collecting and modifying reagent combinations that would enable controllable selective flotation, and (3) to define the influence of different pulp solids, temperature, pH, and time for conditioning and for the rougher and cleaner flotation stages.

Jan 1, 1961

By W. G. Pariseau

A U.S. Bureau of Mines case study of pillar recovery in high-grade ore near the Ross shaft at, the Homestake Mine, Lead, SD, has demonstrated the usefulness of the finite-clement method for the evaluation of shaft pillar mining plans and shaft stability. This report, one of three in a series describing the Ross shaft pillar case study, focuses on the premining stability analysis. The two-dimensional computer program UTAH2 was used in advance of pillar mining; results suggested that the shaft would remain stable. Subsequent reports describe parts 2 and 3 of the study. In part 2, borehole extensometers and other instruments were installed to provide data for model verification and shaft monitoring. Results of the recalibrated two-dimensional model confirmed the premining stability evaluation. However, after mining began, great concern developed because of the appearance of cracks and other signs of ground movement over considerable distances from the area of active pillar miping. In part 3, an intense three-dimensional modeling effort using UTAH3 was initiated. The results again showed that the shaft would remain safe. Three-dimensional analyses of alternative pillar mining scenarios indicated that more of the shaft pillar ore reserve could be recovered than previously thought.

Jan 1, 2010

By J. H. Field

Synthesis of hydrocarbons by the Fischer-Tropsch reaction in a hot-gas- recycle system was demonstrated to be technically feasible. This project was undertaken, by the Bureau of Mines, to determine if the system was operable and to ascertain the optimum conditions for the production of gasoline. Carbon steel turnings packed with a void volume from 88 to 90 pct. were satisfactory catalysts, but steel catalysts with greater void volume, either turnings or steel wool, were not as active. Good temperature control with a pressure drop of less than 0.5 pounds per square inch (p.s,i,) per foot of catalyst bed of turnings was obtained by operating with a recycle to fresh feed ratio of 20 and by splitting the total gas flaw and injecting portions into the reactor at different entry ports.

Jan 1, 1961

By H. Kim, R. W. Plummer, T. J. Stobbe, W. G. Jones

"Exposure to airborne dust in coal mines has caused respiratory disease in coal miners. The causal agent in these diseases remains unknown, although the minerals found in and around the coal seam have been implicated. Toxicological studies designed to establish the effect of different mineral combinations and concentrations are lacking because the mineral content of coal mine dust has not been defined. This paper reports the initial results of a study done to characterize the mineral content of the coal mine dust found in a mine in the Upper Freepott seam in Northern West Virginia. Coal mine dust samples were collected using 4- stage cassette impactors at nine locations in the mine. The samples were analyzed by an x-ray microdiffraction film technique supplemented by energy dispersive scanning electron microscopy. Primary size modes of about 17 to 20 micrometers from the samples collected at the haulageway and the returnside of the continuous miner were found. From the returnside of the roof bolter samples, a primary size mode of 12to15 micrometers was measured. The minerals found in high percentages were illite, kaolinite, quartz, and calcite. The distribution of minerals in inter· and intra- location samples showed wide variations. Trends in these variations are presented. Stobbe, T. J.; Plummer, R. W.; Kim, H.; Jones. W.: Characterization of coal mine dust. Appl. Ind. Hyg. 2:95· 100; 1986. IntroductionDisease-associated dusts in coal mine environments continue to afflict miners in today's modern mines. The relationship between exposure to coal mine dust and the development of various respiratory diseases has been well recognized; however, the reasons for variation in occurrence of these diseases among miners in different geographic areas,(1) rank of coal seams,(2-3) and jobs (4) remain uncertain. Several papers have reported on the causal agent in the development of these diseases. Davis (5) found that the percentage of the non-coal minerals present in the lungs of deceased miners increased as the level oi pneumoconiosis became more severe. Reisner (6) reported that cell damage caused by coal mine dust increases with the mineral and quartz content of the dust and with the geo· logical age and rank of the coals. Two studies, investigating the in vitro effects of mineral dusts. reported by Seemayer and Manojlovic (7) also obtained positive correlation between cytotoxicity and the mineral content of coal mine dust. Gormly (8) postulated that destruction of macrophages by certain mineral dusts is the first step in the development of pneumoconiosis. In 1980, Adamis and Timar (9) reported that quartz. sandstone, slate. respirable colliery dust. bentonite, illite, and some kaolins had cytotoxic effects on rat peritoneal macrophages""in vitro."" Walton,(10) however, reported that the presence of high clay, illite, and kaolin mineral exposures reversed the hazards associated with increasing quartz exposures. This finding was supported by Le Bouffant and coworkers.(11) They reported that illite present in coal mine dust strongly inhibited the pathogenic effects of quartz while kaolin had a weaker inhibitory effect."

Mar 1, 1989

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsater-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig. Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this typo of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By H. F. Yancey

This report, dealing with the separation of coal from its associated impurities by means of a pulsator-type jig, continues the series of reports that have been issued by the Bureau of Mines, in which detailed study has been made of the efficiency and mechanism of separating coal and impurities in various coal-cleaning appliances. The previous reports have dealt with the piston jig, coal-washing table, pneumatic table, and Baum-type jig.5/ Such studies of the separation accomplished by any form of concentration device are essential and necessarily preliminary to any intelligent attempt to improve the performance of such equipment Object and Plan The pulsator-type jig was developed recently by G. A. Vissac. Although two articles(2) describing plants using this type of cleaning unit appeared in 1936, both dealt principally with plant design and layout rather than with plant performance The object of the stork described in this report was to determine the efficiency of the separation made by the pulsator jig on a sized feed, the specific gravity at which the separation between coal and impurity was effected, and the influence of the specific-gravity composition of the coal on the character of the separation made.

Jan 1, 1938

By H. J. Coleman

Knowledge of the types of naturally occurring sulfur compounds in petroleum is of both theoretical and practical interest to petroleum chemists and geologists. This knowledge has been extended by the identification of 77 sulfur compounds, including 36 thiols, 23 chain sulfides, and 18 cyclic sulfides in a 111° to 150° C boiling range distillate of Wasson, Texas, crude oil. The characterization procedure used in separating and identifying these compounds included isothermal distillation, vacuum fractionation, liquid-solid chromatography (alumina adsorption), chemical treatment, gas-liquid chromatography, microdesulfurization, and infrared analysis. The procedural steps described represent a systematic method of sulfur compound analysis considered applicable for determining the nature and concentration of the sulfur constituents present in any straight-run petroleum distillate of the above-boiling range.

Jan 1, 1966

By Edward F. Divers

This Bureau of Mines report describes a new type of scrubber (dust collector) and ventilation system built into the auger support frame (boom) of a Jeffrey 120L continuous mining machine. With this twin scrubber arrangement, one scrubber is mounted into each side of the boom. Each scrubber includes a 2,500-cfm fan, a flooded fibrous-bed scrubber panel, and a water droplet eliminator. The system was designed for minimum size and adds only a few inches to machine height. Exhaust duct design allows flexibility with various airflow configurations to suit both blowing and exhaust fare ventilation systems and brattice distances ranging up to 20 feet. Full-scale tests with exhaust ventilation were conducted at a Mine Safety and Health Administration surface facility at Bruceton, Pa., to determine the scrubbers' methane dilution capability. Several configurations of the twin scrubber-ventilation system produced striking improvements in face methane dilution when compared with conventional systems.

Jan 1, 1981